2005harleyflhtcubolttork spec

You search Auto repair manual PDF 2005harleyflhtcubolttork spec, if there are search results will appear below. If search results do not exist, please search by others keyword.



  2005harleyflhtcubolttork spec Direct Download speed 5282 Kb/s

  2005harleyflhtcubolttork spec Full Version speed 6162 Kb/s



1999 YAMAHA YZF-R6 SERVICE MANUAL

0

Filed Under (Yamaha) by admin on 25-11-2010

download
ENGINE SPECIFICATIONS/ELECTRICAL SPECIFICATIONS SPEC ENGINE SPECIFICATIONS Item Standard Limit Pistons Oil ring Dimensions (B T) End gap (installed) 1.5 2.0 mm 0.10 0.35 mm Crankshaft Crankshaft-journal-to-crankshaft- journal-bearing clearance 0.028 0.052 mm Carburetors ID mark Jet needle Pilot screw turns out 5EB1 #1, 4: N7RA #2, 3: N7SA 1-1/2 2 ELECTRICAL SPECIFICATIONS Item Standard Limit Ignition system Ignition timing 10 BTDC at 1300 r/min Ignition coils Primary coil resistance Secondary coil resistance 0.204 0.276 Ω 8.5 11.5 Ω Oil level switch model (manufacturer) 5EB (DENSO) Fuel pump relay model (manufacturer) Resistance G8R-30Y-M (OMRON) 162 198 Ω -3- TIGHTENING TORQUES SPEC CHASSIS TIGHTENING TORQUES Item Thread size Tightening torque Remarks Nm mkg Engine mounting adjusting bolts Rear shock absorber and frame Pivot shaft adjust bolt M10 7 40 5 0.7 4.0 0.5 -4- CABLE ROUTING SPEC 1 Throttle cables 2 Clutch cable 3 Left handlebar switch lead 4 Starter cable 5 Main switch lead 6 Front brake hose 7 Right handlebar switch lead AInstall the headlight relays onto the headlight housing bridge. BRoute the headlight lead through the plastic guide. CRoute the headlight lead through the headlight bracket right side, and connect relay. DDon’t kink. EPut coupler into stay. FMake sure the connector is out off the bottom end of front cowling. GRoute the right handlebar switch lead in front of the front fork inner tube. HRoute the throttle cables between the brake hose and right handlebar switch lead. IRoute the wire harness through under the left handlebar switch lead and starter cable. JFasten the left handlebar switch lead to the front fork with a plastic locking tie and cut the end of locking tie. KFasten the throttle cables and starter cable with a band. EB206000 CABLE ROUTING -5- CABLE ROUTING SPEC LLocate the end of band to for ward. Route the horn lead outside the throttle cables and fasten it to the under bracket with a plastic locking tie. Cut the end of locking tie. And then, route the horn lead under the brake hose and clamp it to the under cover

Incoming search terms:

1998 YAMAHA YZF-R6 SERVICE MANUAL

0

Filed Under (Yamaha) by admin on 25-11-2010

download
Camshafts Drive system Camshaft cap inside diameter Camshaft journal diameter Camshaft-journal-to-camshaftcap clearance Intake camshaft lobe dimensions Measurement A Measurement B Measurement C Exhaust camshaft lobe dimensions Measurement A Measurement B Measurement C Max. camshaft runout Chain drive (right) 23.000 23.021 mm 22.967 22.980 mm 0.020 0.054 mm 33.05 33.15 mm 25.14 25.24 mm 7.81 8.01 mm 32.55 32.65 mm 25.07 25.17 mm 7.38 7.58 mm 0.08 mm 33.0 mm 25.09 mm 32.50 mm 25.02 mm 0.06 mm
2-5 ENGINE SPECIFICATIONS SPEC Head Diameter Face Width Seat Width Margin Thickness Item Standard Limit Timing chain Model/number of links Tensioning system RH2015/120 Automatic Valves, valve seats, valve guides Valve clearance (cold) Intake Exhaust Valve dimensions 0.11 0.20 mm 0.21 0.30 mm Valve head diameter A Intake Exhaust Valve face width B Intake Exhaust Valve seat width C Intake Exhaust Valve margin thickness D Intake Exhaust Valve stem diameter Intake Exhaust Valve guide inside diameter Intake Exhaust Valve-stem-to-valve-guide clearance Intake Exhaust Valve stem runout Valve seat width Intake Exhaust 24.9 25.1 mm 21.9 22.1 mm 1.14 1.98 mm 1.14 1.98 mm 0.9 1.1 mm 0.9 1.1 mm 0.6 0.8 mm 0.6 0.8 mm 3.975 3.990 mm 3.960 3.975 mm 4.000 4.012 mm 4.000 4.012 mm 0.010 0.037 mm 0.025 0.052 mm 0.9 1.1 mm 0.9 1.1 mm 1.6 mm 1.6 mm 0.5 mm 0.5 mm 3.950 mm 3.935 mm 4.042 mm 4.042 mm 0.08 mm 0.1 mm 0.04 mm 1.6 mm 1.6 mm
2-6 ENGINE SPECIFICATIONS SPEC Item Standard Limit Valve springs Free length Intake (inner) (outer) Exhaust Installed length (valve closed) Intake (inner) (outer) Exhaust Compressed spring force (installed) Intake (inner) (outer) Exhaust Spring tilt Intake (inner) (outer) Exhaust Winding direction (top view) Intake Exhaust 37.0 mm 38.4 mm 41.7 mm 30.0 mm 32.5 mm 36.1 mm 69 79 N (7.0 8.0 kgf) 114 132 N (11.6 13.4 kgf) 160 184 N (16.3 18.7 kgf) Clockwise Clockwise 35 mm 36.5 mm 39.5 mm 2.5/1.6 mm 2.5/1.7 mm 2.5/1.8 mm Cylinders Cylinder arrangement Bore stroke Compression ratio Bore Max. taper Max. out-of-round Forward-inclined, parallel 4-cylinder 65.5 45.5 mm 12.4 : 1 65.50 65.51 mm 0.05 mm 0.05 mm

Incoming search terms:

2000 YAMAHA YZF-R1 SERVICE MANUAL

0

Filed Under (Yamaha) by admin on 27-11-2010

download
CABLE ROUTING SPEC AProperly insert the meter assembly coupler and rubber boot into the meter assembly. BRoute the meter assembly lead through the left side of the headlight housing. CThe speedometer lead with not be tighten. DInstall the headlight relays onto the headlight housing bridge. EConnect to the right front turn signal connectors. FRoute the turn signal leads upper the headlight housing boss. 1 Clutch cable 2 Left handlebar switch lead 3 Starter cable 4 Main switch lead 5 Steering cover EB206000 CABLE ROUTING -21- NRoute the thermo switch/temperature sender sub- wire harness to the outside of the radiator cap. ORoute the right handlebar switch lead behind the throttle cables. Do not cross the throttle cables and the right handlebar switch lead. PRoute the right handlebar switch lead in front of the throttle cables. GFasten the headlight lead with a plastic clamp at white tape mark. HFasten the wire harness to the headlight housing boss with a plastic locking tie. IRoute the headlight lead through the plastic guide. JRoute the throttle cable to the front side of the brake hose. KRoute the clutch cable behind the front fork leg. LMake sure that the horn leads face out. MRoute the throttle cables and right handlebar switch lead between the lower bracket and steering cover. CABLE ROUTING SPEC -22- CRoute the rollover-valve-to-fuel-tank hose to the inside of the fuel hose (California only). DRoute the coolant reservoir breather hose over the timing chain tensioner. EInsert the plastic clip through the hole in the plastic frame panel and then fasten the wire harness and coolant reservoir breather hose with it. FRoute the clutch cable between the radiator bracket and frame and in front of the thermostat assembly breather hose. GRoute the clutch cable to the inside of the radiator inlet hose. HInsert the plastic clamp into the hole in the coolant reservoir’s tab

1996 YAMAHA TDM 850 SERVICE MANUAL

0

Filed Under (Yamaha) by admin on 20-11-2010

download
Model: TDM850 Model code: 4TX2 5AR1 (CH,A) Dimensions: Overall length Overall width Overall height Seat height Wheelbase Minimum ground clearance Minimum turning radius 2,200 mm 790 mm 1,285 mm 805 mm 1,475 mm 165 mm 2,900 mm Radiator: Radiator capacity (including all routes) 1.7 L Tire: Type Size front rear Manufacturer front rear Type front rear Tubeless 110/80 ZR18 150/70 ZR17 BRIDGESTONE*/PIRELLI/MICHELIN BRIDGESTONE*/PIRELLI/MICHELIN BT54F/MTR03/MACADAM 90X BT54R/MTR04/MACADAM 90X *In Austria and Switzerland only Bridgestone tires are equipped on this mode. MAINTENANCE SPECIFICATIONS SPEC ELECTRICAL Item Standard Limit Voltage: 12 V Ignition system: Ignition timing (B.T.D.C.) Advancer type 10 at 1,150 r/min TPS and electrical type Voltage regulator: Type Model /manufacturer No load regulated voltage Semi conductor-short circuit type SH650A-12/SHINDENGEN 14.1 14.9 V Electric fan: Model /manufacturer NAAF20/NIPPONDEN SO CARBURETION CARBURETOR FUEL LEVEL ADJUSTMENT 1. Measure: Fuel level a Fuel level: 15.8 16.8 mm (below the MIKUNI mark) Out of specification Adjust. Adjust the float level by slightly bending the float tang 1. Fuel level measurement and adjustment steps: Place the motorcycle on a level surface. Use a garage jack under the engine to ensure that the carburetors are positioned vertically. Connect the fuel level gauge 2 to the drain pipe. MAINTENANCE SPECIFICATIONS SPEC ELECTRICAL Item Standard Limit Voltage: 12 V Ignition system: Ignition timing (B.T.D.C.) Advancer type 10 at 1,150 r/min TPS and electrical type Voltage regulator: Type Model /manufacturer No load regulated voltage Semi conductor-short circuit type SH650A-12/SHINDENGEN 14.1 14.9 V Electric fan: Model /manufacturer NAAF20/NIPPONDEN SO

Incoming search terms:

Yamaha XVS 650AN Supplementary Service Manual

0

Filed Under (Yamaha) by admin on 15-12-2010

download
MAINTENANCE SPECIFICATIONS ENGINE Item Standard Limit Connecting rod: Oil clearance Color code (corresponding size) 0.031 0.055 mm (0.0012 0.0022 in) Blue Black Brown Green CHASSIS Item Standard Limit Front suspension: Front fork travel Fork spring free length Installed length Spring rate (K1) Stroke (K1) Optional spring Oil capacity Oil level Oil grade 140 mm (5.5 in) 332.5 mm (3.1 in) 287.4 mm (11.3 in) 3.43 N/mm (0.343 kg/mm, 19.2 lb/in) 0 140 mm (0 5.5 in) No 0.507 L (17.4 US oz) 95 mm (3.74 in) Yamaha fork oil 10 WT or equivalent 325.9 mm (12.83 in) Front brake: Type Disc outside diameter thickness Pad thickness inner Pad thickness outer Master cylinder inside diameter Caliper cylinder inside diameter Caliper cylinder inside diameter Brake fluid type Single disk 298 5 mm (11.73 0.2 in) 6.0 mm (0.24 in) 6.0 mm (0.24 in) 14.0 mm (0.55 in) 30.2 mm (1.19 in) 33.3 mm (1.31 in) DOT 4 4.5 mm (0.18 in) 0.8 mm (0.03 in) 0.8 mm (0.03 in) Brake lever & brake pedal: Brake lever free play (at pivot) Brake lever free play (at lever end) Brake pedal position Brake pedal free play Clutch lever free play (at pivot) Clutch lever free play (at lever end) 1 2 mm (0.04 0.08 in) 10 15 mm (0.39 0.59 in) 108 mm (4.25 in) 20 30 mm (0.79 1.18 in) 2 3 mm (0.08 0.12 in) 10 15 mm (0.39 0.59 in) -4- MAINTENANCE SPECIFICATIONS SPEC ELECTRICAL Item Standard Limit T.C.I.: Pickup coil resistance/color T.C.I. unit model/manufacturer 182 222 Ω at 20C (68F)/Gray – Black J4T088/MITSUBISHI (U.S.A) J4T128/MITSUBISHI (CAL) Ignition coil: Model /manufacturer Minimum spark gap Primary winding resistance Secondary winding resistance F6T541/MITSUBISHI 6 mm (0.24 in) 3.6 4.8 Ω at 20C (68F) 10.7 14.5 kΩ at 20C (68F) Voltage regulator: Type Model /manufacturer No load regulated voltage Semi-conductor, short-circuit type SH650C-11/SHINDENGEN 14.1 14.9 V Rectifier: Model /manufacturer Capacity Withstand voltage SH650C-11/SHINDENGEN 18 A 200 V Electric starter system: Type Starter motor: Model /manufacturer I.D. number Output Brush overall length Commutator diameter Mica undercut Starter relay: Model /manufacturer Amperage rating Constant mesh type SM-13/MITSUBA SM-13 0.7 kW 10 mm (0.39 in) 28 mm (1.10 in) 0.7 mm (0.08 in) MS-5F-441/JIDECO 180 A 4 mm (0.16 in) 27 mm (1.06 in) Flasher relay: Type Model /manufacturer Self cancelling device Flasher frequency Wattage Semi transistor type FB257H/DENSO Yes 75 95 cycle/min 27 W 2 + 3.4 W Fuel pump relay: Model /manufacturer G8R-30Y-Q/OMRON

Incoming search terms:

Suspension Basics for BMW Motorcycles

0

Filed Under (BMW) by admin on 30-11-2010

download
tires: Tires are the first part of any suspension system. The design of the tire and even the pressure you run can have a profound affect on the way your motorcycle handles. Stiff, low profile tires will give a sharper feel to the bike, as will higher tire pressures. Those of us who ride our GS’s off the road will decrease the tire pressure to about 50% of the street spec when we are in the dirt. The tire then becomes a very active part of the suspension, but will wallow like an old pig if not re-inflated when pressed back into pavement duty. It still surprises me when we have a customer complain that his BMW needs new shocks when they come in with nearly flat tires. It is possible that the best dollars-per- unit improvement you can make to your BMW may be in keeping the tires inflated. Chassis: There is not much that we can do about the chassis design, unless we are Troy the Welder, but it is a fact that different frames and swing arms flex differently and therefore are part of the suspension. On the Airheads, we often braced various parts of the frame and swing arms, resulting in improved handling that even mere mortals could appreciate. On the latest BMW’s it would take the likes of a Valentino Rossi to even notice if the parts were stiffened. Stiffer is not always better. One of the Japanese racing bike manufactures controls the stiffness of the frame in various areas to allow some flex for better handling. So, Mr. Rossi might not even like it if Troy stiffened his new BMW. Springs: Springs control the ride height of the motorcycle and the ability to allow for different loads. On most BMW’s there is a way to adjust the spring preload to some extent so that the ride can be optimized for a light rider or two-up operation with luggage. Dampers: Dampers control the speed and frequency at which the suspension operates by changing the kinetic (moving) energy to thermal (heat) energy. Without the damper, the suspension would oscillate as each movement occurred, resulting in decreased vehicle control. Dampers on BMW’s fall into two main groups. On airheads, older K bikes, F and G models, and the R1200 HP-2, the front dampers are integrated into the forks. On the rear of the above mentioned -3 – models, and on both ends of all the rest of the bikes, there is a more common shock absorber, around which the spring is located. The HP-2 uses an air spring and air dampened rear shock. Seat: OK, folks, this is here for my old buddy Jeff. We know that a seat isn’t part of suspension, but a bad one sure can make you miserable. We have sent dozens of seats to our friend Mike Harris for inexpensive mods that might improve your riding enjoyment more than any suspension changes you could make! Let us know if we can help you with this most important item

Incoming search terms:

HARLEY DAVIDSON TOURING MODEL BASIC SLIP ON'S INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 22-12-2010

download
1. Remove both saddlebags and set them aside. 2. Loosen the bolt from the pinch clamp on the front end of each muffl er. 3. Working with one muffl er at a time, support the muffl er (assistance may be required) while removing the 5/16″ bolts from the saddlebag support and slide muffl er off of the head pipe. 4. Repeat the process for the opposite muffl er. NOTE: It may be necessary to use a penetrating lubricant to loosen the muffl er from the head pipe 1. Install the band clamps (supplied) over the front of each muffl er so that the bolt is to the inside and the nut is facing down (Figure 1). NOTE: New band clamps are supplied, do not use the old clamps. 2. Install muffl er by sliding it on to the head pipe and bolting it to the saddlebag support using the stock 5/16″ bolts. 3. Repeat installation procedure for opposite muffl er. 4. Align muffl ers and tighten hardware, beginning with the 5/16″ bolts on the mounting brackets followed by the Torca band clamp. Torque spec. is 40-45 Ft./Lbs. 5. Replace the saddlebags. 6. After installation and before starting motorcycle, completely clean pipes and muffl ers with cleaning solvent and a clean, soft cloth that will not leave a residue. NOTE: Any residue, oil, or fi ngerprints will stain the chrome when the metal heats up. 7. Be sure to tighten all hardware before starting your motorcycle

Harley Davidson 2004-Up Sportster EZ-Steer Installation Manual

0

Filed Under (Harley Davidson) by admin on 16-02-2011

download
Installation Notes • Remove front fender, wheel, brake caliper, and fork tubes. • Remove all components attached to stock triple clamps, then the triple clamps themselves. • Remove upper and lower bearings including race. • Install new steering stem bearing races into neck. • Install new upper steering stem bearing with seal into neck. • Install Top and Bottom triple clamps into neck and snug steering stem bolt with washer. • Remove fork tube cap from both forks. • Install fork extensions with o-ring into fork tubes and tighten until fully seated. • Install fork tube caps with o-rings and tighten (see torque table). • Slide fork tubes into triple clamps until the top of each tube cap extends 0.42-0.50 in. above top surface of upper triple clamp. • Tighten 3/8-16 x 1.5″ bolts on upper triple clamp (see torque table). • Tighten steering stem bolt (see torque table). • Tighten pinch bolts on lower triple clamp (see torque table). • Install front wheel assembly and front brake caliper. • Install front fender. Item # Part Description Torque Spec (Lb. Ft.) – Fork Tube Cap 22-58 8 Bolt, Steering Stem, SP 30-35 11 3/8 – 16 X 1.5″ Socket Head Cap Screw 30-35 EZ-Steer Maintenance The bearings in your EZ-Steer rake kit are normal wear items, not subject to replacement under Champion’s one year Limited Warranty for the product. Failure to follow your motorcycle manufacturer’s recommendations for periodic OEM triple-tree maintenance will accelerate the wear on these bearings. Checking/adjustment of the steering stem nut torque with the front end lifted, in accordance with your motorcycle manufacturer’s recommendations, is important to reliable bearing service. Windshield Notes Please note that this EZ-Steer kit accommodates all known windshield types with the exception of a minor modification to Quick Release Compact Windshield, example part no. 58063-04. You will need to oblong the lower bolt holes as shown in figure

Incoming search terms:

YAMAHA YZF-R6R/ YZF-R6SR/ YZF-R6RC/ YZF-R6SRC SERVICE MANUAL

0

Filed Under (Yamaha) by admin on 26-04-2011

download
CABLE ROUTING SPEC A Pass the right handlebar switch lead inside the front brake hoses and over the throttle cables. B Install the throttle cables to the hook so that the pulling side of the throttle cables is routed downward. C Pass the clutch cable through the guide. D Plastic locking tie shall be positioned at 10 mm (0.39 in.) below from the upper bracket. E Clamp the left handlebar switch lead to the front fork with the plastic locking tie and cut the tip of the tie. Clamp it to the protector section Set in the coupler between the head light’s hollow section and the duct. J Install the relay to the rib of the head light. (Location for the left and right relays is alternative.) K To the wire harness L To the front turn signal light (right) M Set the sub wire harness in the joint. N Do not catch the sub wire harness when the duct is assembled. O To the front turn signal light (left) P Point the tip of the plastic locking tie to the front side of the vehicle. Cut the tip leaving 2 X 10 mm (0.08 X 0.39 in). Q Point the tip of the plastic locking tie under the under bracket and rear side of the vehicle. Cut the tip leaving 2 X 10 mm (0.08 X 0.39 in) A Pass the main switch lead under the left handlebar switch lead and then to the right side of the vehicle. B Pass the throttle stop cable by the left side of the side stand switch lead, oil level switch lead, A.C. magneto lead and then to the right side of the vehicle. C Pass the fuel tank drain hose and fuel tank breather hose inside of the reservoir tank breather hose, reservoir tank hose and wire harness and then route it by the out side of the starter motor lead. D Pass the coolant reservoir tank hose outside of the fuel tank drain hose and fuel tank breather hose. E Pass the fuel tank drain hose, fuel tank breather hose through the clamp of the coolant reservoir tank

Incoming search terms:

YAMAHA XT660R(W) XT660X(W) SUPPLEMENTARY SERVICE MANUAL

0

Filed Under (Yamaha) by admin on 27-11-2010

download
CHASSIS SPECIFICATIONS Item Standard Limit Rear wheel Wheel type Spoke wheel —- Rim Size 17M/C × MT2.75 (XT660R) 17M/C × MT4.25 (XT660X) —- —- Material Aluminum —- Wheel travel 200.0 mm (7.87 in) (XT660R) 191.0 mm (7.52 in) (XT660X) —- —- Wheel runout Maximum radial wheel runout —- 2.0 mm (0.08 in) Maximum lateral wheel runout —- 2.0 mm (0.08 in) Wheel axle bending limit —- 0.25 mm (0.01 in) Front tire Tire type With tube —- Size 90/90-21M/C 54S, 90/90-21M/C 54T (XT660R) 120/70R 17M/C 58 H, 120/70ZR 17M/C 58W, 120/70ZR 17M/C 58W (XT660X) —- —- Model/manufacturer TOURANCE FRONT/METZELER, SIRAC/MICHELIN (XT660R) DRAGON/PIRELLI, SPORTEC M1/ METZELER, RADIAL PILOT SPORT/ MICHELIN (XT660X) —- —- Tire pressure (cold) 0 ~ 90 kg (0 ~ 198 lb) 200 kPa (2.00 kgf/cm, 29 psi) (XT660R) 210 kPa (2.10 kgf/cm, 30 psi) (XT660X) —- —- 90 (198 lb) ~ Maximum load* 200 kPa (2.00 kgf/cm, 29 psi) (XT660R) 220 kPa (2.20 kgf/cm, 31 psi) (XT660X) —- —- * Load is the total weight of the cargo, rider, passenger and accessories. Off-road riding 200 kPa (2.00 kgf/cm, 29 psi) (XT660R) —- Minimum tire tread depth —- 1.6 mm (0.063 in)
- 7 – SPEC CHASSIS SPECIFICATIONS Rear tire Tire type With tube —- Size 130/80-17M/C 65S, 130/80-17M/C 65T (XT660R) 160/60R 17M/C 69H, 160/60ZR 17M/C 69W, 160/60ZR 17M/C 69W (XT660X) —- —- Model/manufacturer TOURANCE/METZELER, SIRACA/ MICHELIN (XT660R) DRAGON/PIRELLI, SPORTEC M1/ METZELER, RADIAL PILOT SPORT/ MICHELIN (XT660X) —- —- Tire pressure (cold) 0 ~ 90 kg (0 ~ 198 lb) 200 kPa (2.00 kgf/cm, 29 psi) (XT660R) 210 kPa (2.10 kgf/cm, 30 psi) (XT660X) —- —- 90 (198 lb) ~ Maximum load* 225 kPa (2.25 kgf/cm, 33 psi) (XT660R) 230 kPa (2.30 kgf/cm, 33 psi) (XT660X) —- —- * Load is the total weight of the cargo, rider, passenger and accessories. Off-road riding 200 kPa (2.00 kgf/cm, 29 psi) (XT660R) —- Minimum tire tread depth —-

Incoming search terms:

Incoming search terms: