2006 suzuki eiger choke position

You search Auto repair manual PDF 2006 suzuki eiger choke position, if there are search results will appear below. If search results do not exist, please search by others keyword.





SUZUKI SV 1000 RADIATOR (COOLING SYSTEM) SERVICE MANUAL

0

Filed Under (Suzuki) by admin on 26-02-2011

download
FI SYSTEM MALFUNCTION CODE AND DEFECTIVE CONDITION MALFUNCTION CODE DETECTED ITEM DETECTED FAILURE CONDITION CHECK FOR COO NO FAULT C11 Camshaft position sen- sor The signal does not reach ECM for more than 3 sec . after receiving the starter signal . The camshaft position sensor wiring and mechanical parts (Camshaft position sensor, intake cam pin, wiring/coupler con- nection) C12 Crankshaft position sensor The signal does not reach ECM for more than 2 sec . after receiving the starter signal . The crankshaft position sensor wiring and mechanical parts (Crankshaft position sensor, wiring/coupler connection) C13 Intake air pressure sensor The sensor should produce following voltage . (0.50 V < sensor voltage < 4 .85 V) Without the above range, C13 is indicated. Intake air pressure sensor, wiring/coupler connection C14 Throttle position sen- sor The sensor should produce following voltage . (0.20 V < sensor voltage < 4 .80 V) Without the above range, C14 is indicated. Throttle position sensor, wiring/coupler connection C15 Engine coolant temperature sensor The sensor voltage should be the following. (0.15 V <_ sensor voltage < 4 .5 V) Without the above range, C15 is indicated. Engine coolant temperature sensor, wiring/coupler connection C21 Intake air temperature sensor The sensor voltage should be the following. (0.15 V < sensor voltage < 4 .5 V) Without the above range, C21 is indicated. Intake air temperature sensor, wiring/coupler connection C22 Atmospheric pressure sensor The sensor voltage should be the following. (0.50 V < sensor voltage < 4 .5 V) Without the above range, C22 is indicated. Atm. pressure sensor, wiring/coupler connection C23 Tip over sensor The sensor voltage should be the following for more than 2 sec . after ignition switch turns ON . (0 .20 V < sensor voltage < 4 .80 V) Without the above value, C23 is indicated. Tip over sensor, wiring/coupler connection C24 or C25 Ignition signalCrankshaft position sensor signal is produced and ECM determines the ignition signal but signal from ignition coil is interrupted continuous by 4 times or more. In this case, the code C24 or C25 is indicated. Ignition coil, wiring/coupler connection, power supply from the battery SERVICING INFORMATION 8 .3 C28 Secondary throttle valve actuator No operating voltage is supplied from the ECM, C28 is indicated. STVA can not operate. STVA lead wire/coupler, STVA C29 Secondary throttle valve position sensor The sensor should produce following voltage . (0.10 V < sensor voltage < 4 .90 V) Without the above range, C29 is indicated . Secondary throttle position sensor, wiring/coupler connection C31 Gear position signalGear position signal voltage should be higher than the following for more than 2 seconds. (Gear position switch voltage >_ 0 .6 V) Without the above value, C31 is indicated. Gear position sensor, wiring/coupler connection, gearshift cam, etc. C32 or C33 Fuel injector Crankshaft position sensor signal is produced and ECM determines the injection signal but fuel injection signal is interrupted continuous by 4 times or more. In this case, the code C32 or C33 is indicated. Injector, wiring/coupler connection, power supply to the injector C41 Fuel pump relay No voltage is applied to fuel pump although fuel pump relay is turned ON, or voltage is applied to fuel pump although fuel pump relay is turned OFF . Fuel pump relay, connecting lead, power source to fuel pump relay C42 Ignition switchIgnition switch signal is not input in the ECM . Ignition switch, lead wire/coupler C44 Heated oxygen sensor (HO2S) [For E-02, 19] During 02 feedback control, 02 sensor voltage is higher or lower than the specification . No signal is detected during engine operation or no electrical power is supplied from the battery . HO2S lead wire/coupler connection Battery voltage supply to the HO2S C49 PAIR control solenoid valve (PAIR valve) When no operating voltage is supplied from the ECM, C49 is indicated. PAIR valve can not operate. PAIR valve lead wire/coupler

Incoming search terms:

SUZUKI SV1000/ S SERVICE MANUAL Supplimentary

0

Filed Under (Suzuki) by admin on 26-02-2011

download
CHASSIS BOLT AND NUT Check that all chassis bolts and nuts are tightened to their specified torque. (Refer to below and page 2-29 of SV1000S Service manual for the locations of the following nuts and bolts on the motorcycle.) CHASSIS FRONT FORK REMOUNTING Align the upper surface A of the inner tube with the upper surface B of the steering stem upper bracket. Tighten initially at 1 000 km (600 miles, 1 month) and every 6 000 km (4 000 miles, 6 months) thereafter. ITEM N·m kgf-m lb-ft 1 Handlebar clamp bolt 23 2.3 16.5 2 Handlebar holder set nut 45 4.5 32.5 SV1000K3 5 SUSPENSION SETTING After installing the front fork, adjust the spring pre-load and damping force as follows. SPRING PRE-LOAD ADJUSTMENT There are eight grooves on the spring adjuster. Position 1 provides the maximum spring pre-load and position 8 provides the minimum spring pre-load. STD position: 7 DAMPING FORCE ADJUSTMENT Rebound damping force Fully turn the damping force adjuster 1 clockwise. It is at stiffest position and turn it out to standard setting position. STD position: 1 and 1/4 turns out from stiffest position Compression damping force Fully turn the damping force adjuster 2 clockwise. It is at stiffest position and turn it out to standard setting position. STD position: 1 turn out from stiffest position STANDARD FRONT SUSPENSION SETTING ! FRONT Spring pre-load adjuster Damping force adjuster Rebound Compression Solo and dual riding 7 1 and 1/4 turns out from stiffest position 1 turn out from stiffest position Be sure to adjust the spring pre-load and damping force on both front fork legs equally. 6 SV1000K3 HANDLEBARS REMOVAL AND DISASSEMBLY Remove the handlebar balancer 1. NOTE: Do not remove the handlebar balancer mounting screw before removing the handlebar balancer. Slightly loosen the mounting screw, and then pull the balancer assembly out of handlebars. Remove the rear view mirror 2. Disconnect the front brake light switch coupler 3. Remove the front brake master cylinder. Remove the right handlebar switch 4 and throttle grip 5. Disconnect the clutch switch lead wires 6. Remove the left handlebar switch 7. Remove the rear view mirror 8. Remove the clutch master cylinder. Remove the handlebar clamp caps

Harley Davidson 1990 and later HSR Choke Cable Installation Manual

0

Filed Under (Harley Davidson) by admin on 28-02-2012

download
The majority of HSR42/45 installations use the Harley cable. Installation is simple when the installation instructions are followed, step by step. Those steps are: • Remove the stock Harley choke cable assembly. • Remove the spring and plunger from the stock cable. • Remove the Mikuni “Starter Nut” from the HSR. • Remove the Mikuni spring and plunger from the HSR. • Install the Mikuni spring and plunger on the Harley choke cable. • Install the Harley choke cable with the fitted Mikuni spring and plunger into the HSR carburetor. • DO NOT use the Mikuni Starter Nut; discard it. • DO NOT use the Harley spring or plunger; discard them. Note: If you do not have installation instructions, you may download them from the www.mikuni.com website in the “manuals” section. If the Mikuni Starter Nut is fitted to the Harley cable, the choke plunger is held off its seat and the choke is open all the time. If the Harley spring and plunger are used, the plunger does not seal and the choke is open all the time. The result, in both cases, is very poor fuel mileage (30 mpg or less). Another possible cause of poor mileage, rough idle and fouled spark plugs is incorrect cable routing. The stock Harley choke cable is very stiff and may not be fully seated in the metal elbow at the carburetor end of its run. This condition is easily corrected. On occasion, one of these errors may have been made by someone else at another location. The unfortunate mechanic who inherits the task of correcting the rich condition, poor idle and poor fuel mileage may have no clue as to the mismatch of parts. For this reason, we include the photos and text to help you discover if your installation is correct.

Incoming search terms:

2008 KTM 50 SX JUNIOR 50 SX OWNER'S MANUAL

0

Filed Under (KTM) by admin on 22-10-2010

download
Choke Dell’Orto carburetor PHVA 14 DS (50SXJunior) Choke lever [1] is mounted to the right side of the carburetor. If you move the choke lever up to the stop, a hole is opened in the carburetor through which the engine can draw in additional fuel. This results in a “rich” fuel-air mixture required for a cold start. Moving the choke lever back closes the hole in the carburetor again. Choke Dell’Orto carburetor PHBG 19 BS (50 SX) Choke control knob [2] is mounted to the left side of the carburetor. If you pull the choke control knob up to the stop and turn it 90º, a hole is opened in the carburetor through which the engine can draw additional fuel. This results in a “rich” fuel-air mixture required for a cold start. Turning back the choke control knob returns the knob to the starting position and closes the hole in the carburetor again. Kickstarter The kickstarter is mounted on the right side of the engine. Its upper part can be swivelled. Foot brake lever The foot brake lever is located in front of the right footrest. The basic position can be adjusted to the seating position (see maintenance work). Side stand (50 SXJunior) Use your foot to swing the side stand forwards to the stop. Make sure it rests securely on solid ground.

SUZUKI GSR 600 Accessories

0

Filed Under (Suzuki) by admin on 12-02-2012

download
YBA – Pearl suzuki deep blue no.2 P/N 99000-99074-69N YD8 – Metallic sonic silver P/N 99000-99074-70N YHL – Candy sonoma red P/N 99000-99074-71N YKV – Metallic matt black no.2 P/N 99000-99074-72N YAY – Pearl nebular black P/N 000-99074-73N YMD – Metallic mistic silver P/N 99000-99074-74N YME – Candy max orange P/N 99000-99074-75N YLF – Metallic thunder gray P/N 99000-99074-76N 1 Not in combination with crash pad set (pos. 110) From exhaust to cockpit: the GSR600 is all dressed up 3 102 103 104 106 107 105 102 GSR600 exhaust system by Yoshimura 1 GSR600, model year 2006-2009 P/N 99000-79N12-023 103 Chain guard GSR600, model year 2006-2009 Polished aluminium P/N 990D0-44G10-000 104 Frame covers set GSR600, model year 2006-2009 Carbon look P/N 990D0-44GFC-CRB 105 Tankpad P/N 990D0-44G00-PAD 106 Rear lamp cover GSR600, model year 2006-2009 For original equiped exhaust system P/N 990D0-44G25-PAD For Yoshimura exhaust system P/N 990D0-44G30-PAD 107 Ignition lock cover GSR600, model year 2006-2009 P/N 990D0-44G15-PAD 108 Speedometer cover GSR600, model year 200

Incoming search terms:

2007 KTM 250 SX-F 450 SX-F INSTALLATION MANUAL

0

Filed Under (KTM) by admin on 06-02-2012

download
Clutch lever The clutch lever [1] is located on the left side of the handlebar. The adjusting screw [A] is used to change the original position of the clutch lever (see maintenance work on chassis and engine). The clutch is hydraulically actuated and adjusts itself automatically. Hot start lever If you pull the red hot start lever [2] during the starting procedure backward, a bore in the carburetor will be opened through which the engine may take in additional air. The result is a “lean” fuel-air mixture of the type needed for hot starts. 2 1 A Fuel tap OFF In this position the fuel tap is closed. No fuel can flow to the carburetor. ON During operation the twist grip must be turned to ON. This means that the fuel can flow to the carburetor. OPERATION INSTRUMENTS »
Starter button (450 SX-F) Pushing the black starter button [3] will actuate the E-starter. ENGLISH 6 Hand brake lever The hand brake lever [1] is mounted on the handlebars on the right and actuates the front wheel brake. The adjusting screw [A] can be used to change the basic position of the hand brake lever (see “Maintenance”). Short circuit button The short circuit button [2] turns off the engine. When pressing this button, the ignition circuit is short-circuited. Filler cap To open the filler cap: Turn the filler cap 45 ° counter-clockwise. To close the filler cap: Put the filler cap on and turn it 45 ° clockwise. OFF ON 1 A 2 3 ENGLISH 7 OPERATION INSTRUMENTS » Choke If you pull the choke button [1] out as far as possible, a bore in the carburetor will be opened through which the engine may take in additional fuel. The result is a “fat” fuel-air mixture of the type needed for cold starts. To deactivate the choke, push the choke button back into its basic position. Shift lever The shift lever is mounted on the left side of the engine. The position of the gears is shown in the illustration. Neutral is located between first and second gear. Kickstarter (250 SX-F) The kickstarter is mounted on the right side of the engine. Its upper part can be swivelled. Foot brake pedal The foot brake pedal is located in front of the right footrest. Its basic position can be adjusted to your seat position (see maintenance work). Plug in stand The plug-in stand can be attached to the wheel spindle on the left side of the motorcycle

Incoming search terms:

Hammerhead La Vita 150cc OWNERS MANUAL

0

Filed Under (Hammerhead) by admin on 27-11-2010

download
1. Left and Right rear Mirror 2. Left and Right Brake 3. Front storage compartment (option) 4. Speedometer/ Digital Gauge 5. Main Switch 6. Battery 7. Air Cleaner 8. Seat Lock 9. Rear Light Assembly 10. Left and Right Rear turn Lights 11. Fuel Tank 12. Center Stand 13. Kick Start 14. Side Stand 15. Muffler 16. Left and Right Turn Lights 17. Head Lights 18. Rear Reflector Instrument Panel Speedometer Riding speed is indicated by KM/H and MPH. Odometer The total riding distance is in KM and Miles. The black figures in black background indicate total miles traveled. Indicating lamp or turning light It flashes when turning light is in use. Fuel Gauge Fuel Gauge indicates the remaining fuel in the fuel tank (the gauge does not work when main switch is in the “OFF” position). The gauge moves from “F”(full) to “E” (empty) as fuel decreases in the fuel tank. Fill the tank with 90 Octane or higher gasoline when the needle is approaching the “E” position. There is no reserve tank. Indicating Lamp of High beam It indicates high beam is in use. Note: apply low beam to avoid obstructing the view of oncoming drivers and drivers ahead. 1. Speedometer 2. Odometer 3. Left turn signal indicator 4. Right turn signal indicator 5. High beam indicator 6. Fault signal indicator 7. Battery Gauge 8. Fuel Gauge Instrument Control Main Switch NOTE: – Do not leave the main switch in “ON” position for an extended period of time when the engine is stopped. The battery may drain itself empty. – Lock the steering and remove the key after park to avoid theft. “ON” Position: Electric Circuits are switched on. The engine can now be started. The key can not be removed in this position. “OFF” Position: All electrical circuits are switched off. The engine stops. The key can be removed in this position. “LOCK” Position: The steering is locked when in this position. The key can be removed. Steering Lock Turn the handle bar fully to the left to lock the steering to prevent theft. Push the key in when it is in “OFF” position and while pushing the key in, turn the switch to “LOCK” position to lock the steering. Pull the key out once you are done

2006 King Cobra Service Procedure

0

Filed Under (Cobra) by admin on 10-11-2010

download
Cobra CX50 SR is a close-tolerance high performance machine and break- in time is very important for maximum life and performance. The CX50 SR can be ridden hard after the first ½ hour break-in time but it is recommended that no adjustments are made to the carburetion or suspension until the full 8 hours of bike break-in has elapsed. Also, after the engine, transmission, and drive train have been broken-in for the full 8 hours, the bike will be faster! Use a fuel / oil mixture of 32:1 for the full 8 hour break-in period. Be sure to use high-octane pump gas, with Cobra’s specially formulated Cobra Venom 2-cycle Race Oil . (Part # MCMUOL02) CAUTION: Failure to use proper fuel, oil, or fuel/oil mixture may result in premature engine wear or damage to the machine. Adhering to the following break-in schedule will result in long lasting high performance machine. • Start bike on stand • First 5 minute period, operate the bike on the stand with a combination of idle and high RPM operation. (avoid prolonged high RPM but spin the rear wheel good at least once or twice per minute) • Allow bike to cool • Ride for 15 minutes maximum (avoid prolonged high RPM operation and avoid abusing the clutch with throttle blipping. • Cool and inspect bike for loose fasteners. • Next ½ hour of operation, avoid prolonged operation at Wide Open Throttle. • After 1 hour of operation o Check for loose bolts and nuts on the bike and retighten as necessary (proper toque values are listed under Specifications). o Clean the carburetor bowl. o Change the transmission / clutch lubricant. • After 8 hours of operation o Change the fork oil. o Have a Certified Cobra Mechanic change the shock oil. • Your bike is now ready for the highest level of competition! NOTE: During break-in the bike will likely lose some engine coolant through the radiator overflow hose. Losing up to 4 oz (120 ml, ½ cup) is normal. Proper coolant level will cover the top of the radiator cores. Removing the radiator cap and looking inside is the only way to check the coolant level. 8
Never open the radiator cap of a machine that has a hot or warm engine or one that has recently been ridden. Burning and scalding could occur. CAUTION: It is important that the radiator cap is installed correctly and completely otherwise engine damage could occur. Starting Procedure Before starting the machine inspect the following: • Check for proper tire pressure in both tires. • Observe the chain tension and adjust if necessary. • Observe the coolant level and fill if necessary. • Verify that the chain rollers and sliders do not have improper wear. • Verify that the handlebars are tight. • Check the throttle for smooth operation and that it ‘clacks’ shut properly. • Check for loose bolts and nuts, and re-torque as necessary. • Verify that the air filter is clean and properly saturated with oil. • Insure that the fuel tank contains an adequate volume of fuel / oil mixture to complete the distance required. (High octane pump gas with Cobra’s specially formulated Cobra Venom 2-cycle Race Oil ) • Turn the fuel on by rotating the fuel petcock knob to the vertically downward position (reserve position is horizontally forward) CAUTION: For best results from your Cobra Motorcycle use only the recommended fuels. Testing has shown that most ‘race’ fuels actually degrade performance. Always wear a helmet and other protective riding gear. When your pre-ride inspection is complete the bike may be started. For a cold engine follow this procedure. 1. Place the motorcycle on a stand of sufficient strength that positions the motorcycle in a level upright position with the rear wheel off the ground. 2. Pull up the choke knob and turn it to lock it. 3. Kick start the engine. 4. Rev the engine in short spurts, turning the throttle no more than 1/4 open until the engine will run without the choke.

1994-2003 Suzuki GSXR750 and 1997-2004 Suzuki GSXR600 Superbike Kit INSTALLATION INSTRUCTIONS

0

Filed Under (Suzuki) by admin on 10-01-2011

download
Step 1: Identify the key components that complete our Superbike kit: You should have 2 lines (front kit), 1 double banjo bolt and 2 lower adapters. There are also a total of 7 washers. 5 will be used, and 2 are spares. We strongly suggest having a professional mechanic install these brake lines; all other installations VOID warranty. Inspect your brake system after every race. Step 2: To ensure no paint damage from a brake fluid spill, completely cover the front end of the bike. This process is messy, and brake fluid WILL drip! Step 3: Uninstall stock hoses; be aware of how the stock system was routed in case you need to re-install it. Step 4: Install the Galfer adapters onto the right and left calipers. Thread each adapter into the calipers with one washer, and torque at 12 to 13 ft pounds. (See picture S4) Step 5: Install the right and left lines to the calipers, using the shorter line on the right side. These lines will travel from the master cylinder to the calipers; a double banjo bolt (see picture S5) is included to run two lines down. The positioning sequence on the master cylinder is as follows: Master cylinder, washer, straight banjo (from right line), washer, 12-degree banjo (from left line), washer, and double banjo hex. Double banjo bolt torque level is 12 FT Pounds. ( See picture S6) Make sure that the 90-degree fittings on each caliper are pointing away from the bike just a little bit (see pictures S7 through S9 of calipers) . Thread each banjo end into the adapter, and torque to 6 ½ Ft pounds. Before you proceed to the next step, please check for clearance of the lines. Compress the front end to make sure that the lines are not binding with anything. When the front end is fully extended or fully compressed, double check that the lines are traveling correctly and clear from any obstructions. Once the lines have been checked for clearance, we recommend using a zip-tie to bring the lines together about an inch above the lower triple clamp area. (Picture S10) Step 6: Bleed brake system according to owner’s manual, and build appropriate pressure. Finishing with DOT 4-brake fluid is recommended.

Incoming search terms:

SUZUKI 2005-2006 GSX-R1000 MOTORCYCLES FRAME REINFORCEMENT BRACE INSTALLATION/FRAME REPLACEMENT

0

Filed Under (Suzuki) by admin on 30-11-2010

download
Bodywork removal 1. Refer to section 8 of the service manual and remove the following: a) Right and left Under Cowlings (NOTE: Two of these screws will NOT be re-installed) b) Cover, Front Lower 2. Refer to section 7 of the service manual to remove the radiator mounting bolts. It is not necessary to remove the radiator. 3. Remove the Horn and the Front Engine Cover: a) Remove the Horn. b) Refer to page 3-5 of the service manual and remove the Front Engine Cover. (NOTE: This part will NOT be re-installed) NOTE: To view a video (approximately 10 minutes in length) of the inspection and installation procedure, click here (available on January 23, 2009). Frame inspection 1. Inspecting the frame for damage: a) Inspect the frame for cracks on the left and right sides of the frame as indicated in the photos and graphic below using the Dye Penetrant test kit which will be sent to your dealership by Jan.23th. This inspection has to be done not only on the outside but also on the inside of the frame spars. b) If no cracks are detected, thoroughly clean the frame area using a clean cloth (not a shop rag) and the kit cleaner to remove the dye penetrant used for the inspection. NOTE: * Protect the surrounding areas where inspection is not required from the overspray of the Dye Penetrant. * Read and understand the instructions and handling precautions of the Dye Penetrant before applying it. * If the motorcycle is excessively dirty, prewash it with soap and water before applying the Dye Penetrant.

Incoming search terms: