2006 suzuki eiger float height

You search Auto repair manual PDF 2006 suzuki eiger float height, if there are search results will appear below. If search results do not exist, please search by others keyword.



  2006 suzuki eiger float height Direct Download speed 5282 Kb/s

  2006 suzuki eiger float height Full Version speed 6162 Kb/s



Triumph Bonneville Tuning Manual

0

Filed Under (Triumph) by admin on 20-11-2010

download
1. The Float The float bowl acts as a fuel reservoir to meet engine demand. The float is hinged on a pin in the float boss. It rises and falls with the fuel level in the float bowl. The small metal tang integrated in the plastic float supports the float valve, also known as the float needle. As the fuel in the float bowl rises, the float valve is pushed into the valve seat, until it’s high enough to shut off the fuel flow to the bowl. As fuel is used the level in the bowl drops lowering the float which pulls the float valve from its seat, and fills again. Adjusting the height of the float has a big effect on the mixture as a low or high float level makes it harder or easier for the vacuum to suck fuel into the venturi. Differing float levels cause an imbalance which may be perceived as vibration. 2. The Choke This system is referred to as the choke. But that’s a misnomer. When you pull the choke knob, what you’re doing is retracting a plunger that opens a tube connected to the starter jet, allowing additional fuel to enter the venturi just below the vacuum hose nipple. It supplements the pilot system at start up. 3. The Pilot System The primary purpose of the pilot system is to supply the mixture at idle. It continues to supply fuel throughout the entire throttle range, but after about 1/8 throttle is reached the main system starts to put out more of the total mixture, up to full throttle. By adjusting the idle with the big screw on the left side of the carburettors the position of the butterfly is altered, so exposing one or more of the four small holes that are drilled into the venturi, (leading to the pilot jet) just under the butterfly valve, letting more or less air pass the butterfly. Adjusting the pilot screw that’s under the carburettor varies the amount of air premixing with the fuel before it enters the venturi. 4. The Main System Open the throttle and the cable that’s connected to the butterfly valve turns it from vertical to horizontal, so letting more air through the venturi. This increases the vacuum effect that is transferred up through the vacuum drilling in the slide to the diaphragm valve that leads to the diaphragm chamber. The top chamber is separated from the bottom by a rubber diaphragm. The bottom chamber is open to atmospheric pressure from the airbox. When the vacuum in the top chamber rises enough, the constant ambient pressure of the lower chamber helps the diaphragm valve overcome the downward force of the diaphragm spring, so it rises from the ven- turi. As the diaphragm is raised the needle is pulled out of the needle jet, exposing a thinner portion of the needle taper which allows more fuel to rise into the venturi to meet the increased engine demand. The key parts of the main system are shown in the photo below

Incoming search terms:

SUZUKI GSR 600 Accessories

0

Filed Under (Suzuki) by admin on 12-02-2012

download
YBA – Pearl suzuki deep blue no.2 P/N 99000-99074-69N YD8 – Metallic sonic silver P/N 99000-99074-70N YHL – Candy sonoma red P/N 99000-99074-71N YKV – Metallic matt black no.2 P/N 99000-99074-72N YAY – Pearl nebular black P/N 000-99074-73N YMD – Metallic mistic silver P/N 99000-99074-74N YME – Candy max orange P/N 99000-99074-75N YLF – Metallic thunder gray P/N 99000-99074-76N 1 Not in combination with crash pad set (pos. 110) From exhaust to cockpit: the GSR600 is all dressed up 3 102 103 104 106 107 105 102 GSR600 exhaust system by Yoshimura 1 GSR600, model year 2006-2009 P/N 99000-79N12-023 103 Chain guard GSR600, model year 2006-2009 Polished aluminium P/N 990D0-44G10-000 104 Frame covers set GSR600, model year 2006-2009 Carbon look P/N 990D0-44GFC-CRB 105 Tankpad P/N 990D0-44G00-PAD 106 Rear lamp cover GSR600, model year 2006-2009 For original equiped exhaust system P/N 990D0-44G25-PAD For Yoshimura exhaust system P/N 990D0-44G30-PAD 107 Ignition lock cover GSR600, model year 2006-2009 P/N 990D0-44G15-PAD 108 Speedometer cover GSR600, model year 200

1994-2003 Suzuki GSXR750 and 1997-2004 Suzuki GSXR600 Superbike Kit INSTALLATION INSTRUCTIONS

0

Filed Under (Suzuki) by admin on 10-01-2011

download
Step 1: Identify the key components that complete our Superbike kit: You should have 2 lines (front kit), 1 double banjo bolt and 2 lower adapters. There are also a total of 7 washers. 5 will be used, and 2 are spares. We strongly suggest having a professional mechanic install these brake lines; all other installations VOID warranty. Inspect your brake system after every race. Step 2: To ensure no paint damage from a brake fluid spill, completely cover the front end of the bike. This process is messy, and brake fluid WILL drip! Step 3: Uninstall stock hoses; be aware of how the stock system was routed in case you need to re-install it. Step 4: Install the Galfer adapters onto the right and left calipers. Thread each adapter into the calipers with one washer, and torque at 12 to 13 ft pounds. (See picture S4) Step 5: Install the right and left lines to the calipers, using the shorter line on the right side. These lines will travel from the master cylinder to the calipers; a double banjo bolt (see picture S5) is included to run two lines down. The positioning sequence on the master cylinder is as follows: Master cylinder, washer, straight banjo (from right line), washer, 12-degree banjo (from left line), washer, and double banjo hex. Double banjo bolt torque level is 12 FT Pounds. ( See picture S6) Make sure that the 90-degree fittings on each caliper are pointing away from the bike just a little bit (see pictures S7 through S9 of calipers) . Thread each banjo end into the adapter, and torque to 6 ½ Ft pounds. Before you proceed to the next step, please check for clearance of the lines. Compress the front end to make sure that the lines are not binding with anything. When the front end is fully extended or fully compressed, double check that the lines are traveling correctly and clear from any obstructions. Once the lines have been checked for clearance, we recommend using a zip-tie to bring the lines together about an inch above the lower triple clamp area. (Picture S10) Step 6: Bleed brake system according to owner’s manual, and build appropriate pressure. Finishing with DOT 4-brake fluid is recommended.

Incoming search terms:

2004-2006 Suzuki RM-Z250 Kickstand Installation Instructions

0

Filed Under (Kawasaki) by admin on 25-10-2010

download
To install your new kickstand: 1. Remove the lower chain roller nut, leave the factory washer installed. Install the included threaded chain roller spacer on the chain roller stud, and tighten. (DO NOT OVER TIGHTEN!) 2. Remove the sub-frame to main-frame mounting bolt. Install the provided subframe bolt spacer into the subframe bolt hole. 3. Install kickstand on the bike using the provided M8X 30mm flat head bolt, in the upper mounting hole. Install the supplied M6X 16mm socket head bolt, in the bottom mounting location. 4. Make sure that you tighten all bolts to the correct torque. 5. Periodically check the kickstand pivot bolt for tightness. Maintenance: Clean and lubricate the kickstand pivot area after each ride. We recommend using a penetrating lube, such as WD-40. If necessary, you can remove the back cover plate for additional cleaning.

SUZUKI 2005-2006 GSX-R1000 MOTORCYCLES FRAME REINFORCEMENT BRACE INSTALLATION/FRAME REPLACEMENT

0

Filed Under (Suzuki) by admin on 30-11-2010

download
Bodywork removal 1. Refer to section 8 of the service manual and remove the following: a) Right and left Under Cowlings (NOTE: Two of these screws will NOT be re-installed) b) Cover, Front Lower 2. Refer to section 7 of the service manual to remove the radiator mounting bolts. It is not necessary to remove the radiator. 3. Remove the Horn and the Front Engine Cover: a) Remove the Horn. b) Refer to page 3-5 of the service manual and remove the Front Engine Cover. (NOTE: This part will NOT be re-installed) NOTE: To view a video (approximately 10 minutes in length) of the inspection and installation procedure, click here (available on January 23, 2009). Frame inspection 1. Inspecting the frame for damage: a) Inspect the frame for cracks on the left and right sides of the frame as indicated in the photos and graphic below using the Dye Penetrant test kit which will be sent to your dealership by Jan.23th. This inspection has to be done not only on the outside but also on the inside of the frame spars. b) If no cracks are detected, thoroughly clean the frame area using a clean cloth (not a shop rag) and the kit cleaner to remove the dye penetrant used for the inspection. NOTE: * Protect the surrounding areas where inspection is not required from the overspray of the Dye Penetrant. * Read and understand the instructions and handling precautions of the Dye Penetrant before applying it. * If the motorcycle is excessively dirty, prewash it with soap and water before applying the Dye Penetrant.

Incoming search terms:

Suzuki GSXR600/ 750 2006-2007 Frame Slider Installation Manual

0

Filed Under (Suzuki) by admin on 13-02-2012

download
There is an existing 1 inch hole in the right body panel, remove right side bolt. Mount right side puck (shorter slider) with (99-HB-SH10125080) Socket Cap 10 X 1.25 X 80 Main Engine Stud and torque down. 2. Remove left side panel. 3. Locate the left side engine stud and remove bolt. (arrow below is pointing to bolt location) 4. Some photos in this section are used for illustration examples only. It is up to you how you decide to cut your motorcycles bodywork to accept the frame slider there are many different ways customers go through this process. Shogun is not responsible for any part of your motorcycle for any reason. Precisely measure location of cut and if in doubt at any point please call us before the install process has begun. Professional installation is recommended. Always use proper safety measures during the install of this product. Do not try to install this product without proper tools, recently calibrated torque wrench, correct torque specifications from factory service manual, safety goggles and gloves. 5. Body Prep. Use masking tape to completely mask off the area on the body where you will be working. We usually will tape off approximately 6 to 8 inches around the though hole area and any other edges that could get bumped or scratched while working. Tip: In some locations you may want to double up the thickness of the masking take to give extra protection.

SUZUKI MOTORCYCLES Gsxr 600, Gsxr 750, Gsxr 1000 teak the lead

0

Filed Under (Suzuki) by admin on 12-11-2010

download
The launch of the sixth generation of Gsxr marked a shift in Suzuki’s emphasis on two fronts. One, the Gsxr 1000 now took the upper hand in the development stakes. Historically, the Gsxr 750 led the march-arriving first, gaining the most recent technology, absorbing the lion’s share of corporate pride-but by 2003 the Gsxr 1000 was in the lead. Two, the Gsxr 1000 represents another, more subtle shift for Suzuki engineering, in which the designers-the lucky guys who get to clothe these amazing machines-have more freedom of expression. With this generation, the designs turned edgier, sharper, more aggressive looking than ever. What’s more, the Gsxr 1000 K3 would be the proving ground for a host of changes brought to the Gsxr 600 and Gsxr 750 for 2004. In fact, nearly every upgrade to the smaller bikes appeared on the Gsxr 1000 a year before. But the real impetus for driving the Gsxr 1000 to the head of development and, indeed, shortening its development cycle was competition both on the track and in the showroom. For the track, it was understood that Superbike racing would revert to allowing 1000 cc four-cylinder bikes in place of the 750s that had been the limit since 1982. In 2002, Yoshimura and Mat Mladin barely lost the AMA Superbike crown to Nicky Hayden aboard the Honda RC5!. But it would be the RC’s swan song of competitiveness with the change to 1000 cc fours. To keep speeds in check, the AMA Superbike rules would require 1000 cc fours to have some additional limitations compared to the twins and triples. For example, “Cylinder heads may be ported and machined, but altering of valve angles will not be permitted; aftermarket valves, springs, retainers, and other valve-train components will be permitted; valves must be stock size and same basic material as original equipment; aftermarket camshafts will be permitted, but earn lift and resulting valve lift must be no greater than stock. “In addition, the “stock crankshaft must be retained, The only allowable modifications are balancing, polishing of bearing surfaces and attachment of accessory drives. Homologated transmission gear sets (one optional set of ratios per approved model) will be permitted. Optional sets will be price-controlled and must be available to any legitimate AMA Superbike competitor. Homologated fuel-injection throttle-body assemblies (one optional type per approved model) and aftermarket airboxes will be permitted. Modifications to throttle bodies will not be permitted. Optional throttle bodies will be price-controlled and must be available to any legitimate AMA Superbike competitor.” The thinking was simple: keep the liter bikes from sucking through massive throttle bodies, and the horsepower might not (and, it was hoped, would not) go through the roof. In preparation for racing, Suzuki moto wanted to make a host of small changes to the Gsxr 1000, but its motivation was also to keep the bike at the forefront of open-class street bikes. Suzuki engineers knew that Honda and Kawasaki were readying all-new models-the CBR 954 RR and the ZX 9 R had long since been vanquished-and rumor had it that Yamaha was ready with yet another push with the R1.It was the right time to make alterations to the Gsxr 1000. Heading the list was, as one might expect, a revised engine.

Incoming search terms:

SUZUKI PUTS THE 'STYLE' IN LIFESTYLE WITH CUSTOM ACCESSORIES INSTALLATION

0

Filed Under (Suzuki) by admin on 14-02-2012

download
Suzuki Genuine Accessories are available for the all-new Equator midsize pickup truck, four-door SX4 Sport, five-door SX4 Crossover, XL7 midsize crossover and rugged Grand Vitara. The accessories can be purchased through local Suzuki dealers. Suzuki Equator  All-weather floor mats – Rubberized all-weather mats, ideal for keeping dirt, moisture and harsh debris from coming in contact with the vehicle’s carpet interior.  Bluetooth® module – The Suzuki-integrated hands-free Bluetooth phone system features a clean installation, fresh look and works with most Bluetooth-enabled mobile phones. Quality sound plays through the vehicle’s factory stereo and speakers, and the phone system automatically mutes the radio during phone calls. (Also available for SX4 Sport, SX4 Crossover, Grand Vitara and XL7.)  Body side moldings – Durable polyurethane molding set helps protect exterior paint from door dings and road rash.  Hood mask – Durable vinyl, custom-fit mask helps protect the front end of the vehicle from damage caused by minor road debris.  iPod® interface kit – Provides a seamless connection from an iPod to the vehicle’s radio and/or steering-wheel audio controls. (Also available for SX4 Sport, SX4 Crossover, Grand Vitara and XL7.)

Harley Davidson Softails Airtail Suspension System Installation Instructions

0

Filed Under (Harley Davidson) by admin on 30-11-2010

download
Step 1: Set the Bottoming Control This is the most important step and needs to be done first. Ideally, with the rear wheel off the ground take a measurement from the axle straight up to a fixed point on the fender (assuming the fender is mounted on the frame and not the swingarm). Then, with the motorcycle back on the ground and the rider on it, pressurize the “Bottoming Control” chamber until you get the same measurement —less 1 ¼ to 1 ½”. For example, if your first measurement was 10.0″ inches then your ending measurement should be between 8.50″ and 8.75″ inches. The difference between the two measurements is referred to as “sag”, and it should equal approximately one third of your total wheel travel (see figure 3). Another method of achieving the proper sag is it start with the bike on the ground — with no rider or load on it. Pressurize the “Bottoming Control” chamber to the highest pressure you can without exceeding 150 psi. At this point the rear wheel should be “topped out” and you need to measure from the axle straight up to a fixed point on the fender as described above. Take the same measurement with rider(s) on the bike — ready to ride. The second measurement should be 1¼” to 1½ ” less than the first. If it isn’t, then bleed off the pressure in the “Bottoming Control” chamber until the proper sag is achieved. If you intend to ride the bike at this “full height” then make sure you still put about 10 psi into the “Ride Height” chamber anyway. This helps the piston that separates the two chambers to move more freely producing a smoother ride. Step 2: Set the Ride Height After you have set the “Bottoming Control” you can now adjust the “Ride Height” chamber. This is a much simpler and less crucial adjustment to make. Simply pressurize the “Ride Height” chamber until the bike is lowered to the desired height. To raise the ride height back up, release pressure in the “Ride Height” chamber. Remember, the pressure in this chamber “holds” the bike down—the more pressure the lower it goes. Though the bike may feel “stiffer” the lower you go, do NOT re-adjust the “Bottoming Control” chamber. Essentially what’s happening here is as you’ve reduced your wheel travel, you’ve proportionally increased the forces that keep you from bottoming out with what wheel travel you have left. If you do need to re-adjust the “Bottoming Control” due the addition (or subtraction) of a passenger or extra load, release the pressure from the “Ride Height” chamber first, then repeat step 1.

Incoming search terms:

2003 SUZUKI SV 1000 Service Manual

0

Filed Under (Suzuki) by admin on 26-02-2011

download
HOW TO USE THIS MANUAL TO LOCATE WHAT YOU ARE LOOKING FOR : 1. The text of this manual is divided into sections . 2. The section titles are listed in the GROUP INDEX . 3 . Holding the manual as shown at the right will allow you to find the first page of the section easily . 4. The contents are listed on the first page of each section to help you find the item and page you need . COMPONENT PARTS AND WORK TO BE DONE Under the name of each system or unit, is its exploded view . Work instructions and other service information such as the tightening torque, lubricating points and locking agent points, are provided . Example: Front wheel SYMBOL Listed in the table below are the symbols indicating instructions and other information necessary for servicing. ENGINE OIL SUZUKIrecommends the use of SUZUKI PERFORMANCE 4 MOTOR OIL or an oil which is rated SF or SG under the API (American Petroleum Institute) service classification. The recommended viscosity is SAE 1 OW-40 . If an SAE 1 OW-40 oil is not available, select an altematice according to the right chart . BRAKE FLUID Specification and classification: DOT 4 A WARNING Since the brake system of this motorcycle is filled with a glycol-based brake fluid by the manufacturer, do not use or mix different types of fluid such as silicone-based and petroleum-based fluid for refilling the system, otherwise serious damage will result . Do not use any brake fluid taken from old or used or unsealed containers . Never re-use brake fluid left over from a previous servicing, which has been stored for a long period. FRONT FORK OIL Use fork oil L01 or an equivalent fork oil . GENERAL INFORMATION 1-5 ENGINE COOLANT Use an anti-freeze/engine coolant compatible with an aluminum radiator, mixed with distilled water only . WATER FOR MIXING Use distilled water only . Water other than distilled water can corrode and clog the aluminum radiator . ANTI-FREEZE/ENGINE COOLANT The engine coolant perform as a corrosion and rust inhibitor as well as anti-freeze . Therefore, the engine coolant should be used at all times even though the atmospheric temperature in your area does not go down to freezing point. Suzuki recommends the use of SUZUKI COOLANT anti-freeze/engine coolant. If this is not available, use an equivalent which is compatible with an aluminum radiator . LIQUID AMOUNT OF WATER/ENGINE COOLANT

Incoming search terms:

Incoming search terms: