2006 wildfire r2

You search Auto repair manual PDF 2006 wildfire r2, if there are search results will appear below. If search results do not exist, please search by others keyword.



  2006 wildfire r2 Direct Download speed 5282 Kb/s

  2006 wildfire r2 Full Version speed 6162 Kb/s



Corolla & Matrix 2005 – 2006 1ZZ-FE ENGINE NO START OR EXTENDED CRANK CONDITION

0

Filed Under (Toyota Manuals) by admin on 29-05-2011

Download
Some 2005 and 2006 model year Corolla and Matrix vehicles equipped with a 1ZZ–FE engine may exhibit a “no start” or “extended crank” condition. This may be caused by insufficient fuel pressure after the vehicle has been parked for a period of time. The fuel pump assembly manufacturing process has been improved to correct this condition. Applicable Vehicles S 2005 – 2006 model year Corolla and Matrix (2WD) vehicles equipped with the
1ZZ–FE engine. Parts Information PREVIOUS PART NUMBER 77020–02180 77144–04010 77169–02050 CURRENT PART NUMBER Same Same Same PART NAME Fuel Suction w/Pump & Gauge Tube Assembly Fuel Pump Gauge etainer
Fuel Suction Tube Set Gasket

Incoming search terms:

2004 – 2006 4Runner TIRE PRESSURE SENSING TRANSMITTER ACTIVATION PROCEDURE DURING PDS

0

Filed Under (Toyota Manuals) by admin on 29-10-2011

download
pressure data is transmitted through a Tire Pressure Warning System antenna to the Tire Pressure Monitoring System receiver. The tire pressure sensing transmitter used for the Tire Pressure Monitoring System (TPMS) on 2004 – 2006 model year 4Runner vehicles needs to be activated during Pre-Delivery Service (PDS). 2004 – 2006 model year 4Runner vehicles. NOTE: After all the tire pressure sensing transmitters are activated, the flashing Low Tire Pressure Warning Light goes OFF. The Diagnostic Trouble Codes (DTCs) listed below may be stored in the system until the tire pressure sensing transmitters are activated. The codes will automatically clear when the tire pressure sensing transmitters are activated

Incoming search terms:

WILDFIRE WFH50-S2 Gas Scooter Owner's Manual

0

Filed Under (Tips and Review) by admin on 21-11-2010

download
Main Switches On Position: • Electrical circuits are switched on. The engine can be started and the key can not be removed. • Do not leave the main switch in the on position for an extended period of time if the engine is not running Off Position: • All electrical circuits are off and the engine is stopped. The key can be removed in this position. Steering Lock Position: • Turn the handlebars to the left as far as they will turn, turn the key to the lock position and remove. Steering Lock Position On Position Off Position Wildfire WFH50-S2 Maintenance Table The X indicates at how many miles you need to check the Item. Must change oil: change before riding, again at 500 miles and then 2500 or yearly which ever comes first. Capacities Fuel Capacity: 1 gallon Final drive oil capacity: 3.5 ounces Tire air pressure: Front 28 psi and rear 32 psi. ITEM 500 1000 20002500 3500 40004500 5000 60006500 Check Daily Engine Oil and Filter X X X X X X Gear Oil X X X X Valve Clearance X X Cam Chain X X Carburetor X X Air Cleaner Clean Every 1500 miles, Replace Every 3500 miles Fuel Filter Clean Every 1000 miles, Replace if Necessary Brake System X X X X X X X Drive Belt X Screws and Nuts X X X X X *When riding in a dusty environment, check and clean the air filter element more often. Battery • This scooter uses a sealed lead acid battery, it is unnecessary to check or add liquid. NOTE: Never open the electrolyte of a sealed battery. Remove the battery from the scooter and store separately in a well ventilated area when the scooter is not in operation for long periods of time Speedometer • Speed is measured in mph. Odometer • The total riding distance is indicated. Fuel gauge • The gauge indicates how much fuel is in the tank (the gauge does not work when the ignition switch is off). The needle moves from full “F” to empty “E” as your fuel decreases. Fill the tank with a good grade of 89-90 octane unleaded gasoline. High Beam Indicator LIght • The high beam light indicates that the high beam headlight is in use. NOTE: Apply the low beam to avoid obstructing the view of other drivers. Turn Signal Indication Light • The turn signals indicate that you are turning a chosen direction, push the button in the desired turning direction, it will return to the center, press the button in to turn off. Speedometer Odometer Turn Signal Indication Light High Beam Indication Light Fuel Gauge 4 General Safety Precaution • Scooters can be hazardous to operate. Please operate it with the following safety instruction. If you fail to take proper precautions, a collision or fall may quickly occur. If you have any questions as to the operating condition of your scooter, turn off the engine and walk your scooter. These scooters should be ridden by persons with good vision, balance, coordination, reflex, strength and decision making capability. • Please read this manual and all safety labels carefully, and follow correct operating procedures. • Before each time you ride make sure that the brakes work properly. • Never operate your scooter without wearing proper safety equipment that includes helmet, shoes, etc… • Never operate your scooter under influence of alcohol or drugs. • Always ride with both hands on the handle bars. • Never operate at excessive speeds. Proper speed is determined by terrain, visibility, operating condition and experience. • Never attempt wheelies, jumps or other stunts. • Always inspect your scooter prior to each use to make sure all bolts are tight, and is in safe operating condition.

Incoming search terms:

2006 Honda GL1800 AirbagCB Radio Squeal REPAIR PROCEDURE

0

Filed Under (Honda) by admin on 08-04-2011

download
To remedy this problem, a ferrite core harness kit is now available for installation. 2006 GL1800 VIIIA (Airbagmodels) with optional CBRadio. Install a ferrite harness core kit according to the installation instructions that are packaged with the kit. ÒÑÌÛæ • The kit includes both a rider and a passenger harness; it’s necessary to install both harnesses to eliminate the squealing noise. • Passengers must route the headset cord as shown. If routed otherwise, it will be too close to the motorcycle’s antenna, which can create an interference. Subharness installation can be confirmed by removing the left-side fairing pocket, and check- ingtoseeifthe harness is already installed. Ferrite CoreHarness Kit (1 required) P/N: 08E95-MCA-100WA H/C: 8607665 ÒÑÌÛæCallTechLineat (800) 421-1900 to order parts. Due to the limited number of affected units and parts availability, ordering will be controlled until May 31,2007. Normal warranty claim submission require- mentsapply. Submit one claim per VIN. Template: GL19 Flat RateTime: 0.3 hours

2006 TRIUMPH SPEED TRIPLE ALUMINUM, CARBON FIBER, SLIP-ON EXHAUST SYSTEM INSTALLATION

0

Filed Under (Triumph) by admin on 30-10-2010

download
1) Place the motorcycle in a vise or on it’s stand and make sure it is safe and secure. 2) Remove the right side muffler heat shield. Loosen the right side muffler inlet clamp. Remove and retain the muffler mounting bolt and nut. Remove the right side muffler from the motorcycle. 3) If the gasket remained on the stock muffler inlet tube, remove it and inspect. Replace if necessary and then install onto the Jardine muffler inlet tube. 4) Slide the Jardine muffler into the stock s-bend outlet. 5) Attach the rubber strip to the inside of one supplied muffler clamp. Slide the muffler clamp over the muffler withe the offset facing inward. Squeeze both muffler clamp tabs together and secure it to the muffler mounting bracket using the original bolt and nut. Do not fully tighten yet. 6) Adjust the muffler so it is straight and fully tighten the t-bolt clamp, then the muffler clamp hardware. 7) Repeat steps #2-6 for the left side muffler. 8) Clean all fingerprints from the muffler. Start the motorcycle and check for any exhaust leaks. Ratchet 12mm Socket 12mm Wrench Spring Tool or Needlenose Pliers 2 – Mufflers (Left & Right) 2 – Muffler Clamps 2 – Rubber Strips SLIP-ON EXHAUST SYSTEM TRIUMPH SPEED TRIPLE 2006 18-7008-123-02 ALUMINUM 18-7008-323-02 CARBON FIBER PERFORMANCE DELIVERED! All Jardine products are warranted against defective materials and workmanship for a period of 90 days from date of original consumer purchase. Any non-defective item may be returned within 7 working days, and will be subject to a 20% restocking/repackaging fee. WHATIS WARRANTED: Any Jardine product returned, with prior approval, for defective materials or workmanship including chrome blistering, peeling, bubbling, or any unused (new) Jardine product with rust damage

Incoming search terms:

2006 Model Engine Oil Recommendation Chart

0

Filed Under (KTM) by admin on 26-11-2010

download
2006 Model Type Recommended Engine Oil Type Quantity SPORTMINICYCLES AC 50 MINI ADVENTURE Motorex ATF Super (Dexron II Gear Oil) 0.15-0.2 L 50 SENIOR ADVENTURE Motorex ATF Super (Dexron II Gear Oil) 0.15-0.2 L SPORTMINICYCLES LC 50 SX JUNIOR Motorex Top Speed 4T 15W50 0.15-0.2 L 50 SX Motorex Top Speed 4T 15W50 0.15-0.2 L 65 SX Motorex Top Speed 4T 15W50 0.3L SX 2 STROKE 85 SX Motorex Top Speed 4T 15W50 0.5 L 105 SX Motorex Top Speed 4T 15W50 0.5 L 125 SX Motorex Top Speed 4T 15W50 0.7 L 250 SX Motorex Top Speed 4T 15W50 0.7 L SX 4 STROKE 250 SX-F Motorex Power Synt 4T 10W50 1.1 L 450 SX Motorex Power Synt 4T 10W50 1.25 L 525 SX Motorex Power Synt 4T 10W50 1.25 L CROSS COUNTRY 2 STROKE 200 XC Motorex Top Speed 4T 15W50 0.7 L 200 XC-W Motorex Top Speed 4T 15W50 0.7 L 250 XC Motorex Top Speed 4T 15W50 0.7 L 250 XC-W Motorex Top Speed 4T 15W50 0.7 L 300 XC Motorex Top Speed 4T 15W50 0.7 L 300 XC-W Motorex Top Speed 4T 15W50 0.7 L CROSS COUNTRY 4 STROKE 450 XC Motorex Power Synt 4T 10W50 1.25 L 525 XC Motorex Power Synt 4T 10W50 1.25 L ENDURO RACING 400 EXC Motorex Power Synt 4T 10W50 1.25 L 450 EXC Motorex Power Synt 4T 10W50 1.25 L 525 EXC Motorex Power Synt 4T 10W50 1.25 L ADVENTURE LC8 950 Adventure orange Motorex Power Synt 4T SAE 10W50 (for temperatures over 32° F) and 5W40 (for temperatures under 32° F) Approx. 3.0 L 950 Adventure black Motorex Power Synt 4T SAE 10W50 (for temperatures over 32° F) and 5W40 (for temperatures under 32° F) Approx. 3.0 L 950 Adventure S Motorex Power Synt 4T SAE 10W50 (for temperatures over 32° F) and 5W40 (for temperatures under 32° F) Approx. 3.0 L SUPERMOTO RACING 450 SMR Motorex Power Synt 4T 10W50 1.25 L 560 SMR Motorex Power Synt 4T 10W50 1.25 L SUPERMOTO LC4 625 SMC Motorex Power Synt 4T 10W50 Approx. 2.1 SUPERMOTO LC8 950 Supermoto orange Motorex Power Synt 4T SAE 10W50 (for temperatures over 32° F) and 5W40 (for temperatures under 32° F) Approx. 3.0 L 950 Supermoto black Motorex Power Synt 4T SAE 10W50 (for temperatures over 32° F) and 5W40 (for temperatures under 32° F) Approx. 3.0 L

Wildfire Scooter WF 250CB Owner's Manual

0

Filed Under (Uncategorized) by admin on 26-11-2010

download
• Check before Riding • Make sure the brakes work properly and adjust if necessary. • Check all nuts and bolts for tightness. • Make sure that the gas tank is full. • Check tire pressure. • Check all gauges. • Check and make sure that all of the lights are working properly, headlight, taillight, turn signal etc. • Check the engine oil. STARTING, RIDING, STOPPING AND PARKING Before starting, put the kickstand up. • Practice in an empty area away from people and vehicles. • Always remember to obey your local and state laws and regulations. • Be sure your bike has fuel and oil. • Be sure the bike is in neutral. • Apply the rear brake. • Turn the key on. • Press the electric start button. • After engine warms up, push the choke 1/4 in then 1/2 in and in 1 minute completely off. • If the engine is warm it should start without choking. • For a cold engine, let the engine idle for 1-3 minutes before driving, then begin to turn the choke off. • Never exceed 4 seconds when engaging the starter. • Release the button immediately after the engine starts. • Do not apply the key while the engine is running, it can cause damage to the starter. • Sit on the bike keeping one foot on the ground for stability, release the clutch by pulling in the lever, shift bike into first gear by using the foot shifter. • Apply the throttle gradually as you release the clutch lever slowly until the clutch engages. • To shift into the next gear release the throttle pull the clutch lever in and shift into the next gear, after you shift, gradually apply the throttle and slowly release the clutch. • Use this sequence when shifting to all gears. • Only put your feet on the ground when coming to a stop. • When coming to a stop decrease your speed by releasing the throttle and applying the brakes and the clutch, if the tire skids release the brake and reapply. • Parking: Put your kick stand down. Park away from pedestrians. NOTE: The muffler and exhaust pipe are h

Wildfire WFH 150-T Touring Scooter Specification And Owner's Manual

0

Filed Under (Wildfire) by admin on 29-11-2010

download
Engine Oil Replacement • Replace the engine oil after the first 50 miles or 1 hour with 5w50, 10w50 or 15W50 synthetic engine oil. Then replace again every 1,500 miles or 1 each year. Check oil level every 500 miles, add oil if needed. Changing the Engine Oil (1).Warm up the engine for a few minutes. (2).Stop the engine. (3). Place scooter on center stand. (4).Place an oil pan under the engine and remove the dipstick. (5).Remove the drain plug and drain the oil. Reach in drain hole, pull out filter clean and reinstall, after all oil drains out. (6).Reinstall drain plug. (7). Fill the engine with oil until the level is in the designated area on the dipstick. (8).Start the engine and check for oil leaks. If a leak is found stop the engine immediately and look for cause. Rear Wheel Oil Replacement • Replace the gear oil after the first 500 miles with 5W/50 synthetic engine oil. Replace the gear oil again every 4 months or every 2000 miles. • Replacing the Gear Oil (1).Put the scooter on the center stand (please see photo below) . (2).Place an oil pan under the gear case (please see photo below) . (3).Remove the oil filler bolt and the drain plug to drain the oil (please see photo below) . (4).Reinstall and tighten the drain plug. (5).Fill the gear case with oil (please see photo below) . (6).Reinstall the oil filler bolt. (7).Check for oil leakage. Cleaning Air Cleaner Be sure to check the air cleaner regularly. (1).Place the scooter on the center stand. (2).Unscrew and remove the left side panel. (3).Remove the air cleaner cover by removing the screws. (4).Take out the air cleaner by removing the screws. (5).Remove the air cleaner element and wash it gently, but thoroughly in solvent. Replace if damaged. (6).Squeeze out the excess solvent and dry it. (7).Apply oil to the entire surface of the air cleaner and squeeze out the excess oil. It should be damp but not dripping. (8).Install the air cleaner, cleaner cover, and left side panel. center stand 1 oil pan 2 3 oil drain plug oil pan 5 Main Switches On Position: • Electrical circuits are switched on. The engine can be started and the key can not be removed.

2006 King Cobra Service Procedure

0

Filed Under (Cobra) by admin on 10-11-2010

download
Cobra CX50 SR is a close-tolerance high performance machine and break- in time is very important for maximum life and performance. The CX50 SR can be ridden hard after the first ½ hour break-in time but it is recommended that no adjustments are made to the carburetion or suspension until the full 8 hours of bike break-in has elapsed. Also, after the engine, transmission, and drive train have been broken-in for the full 8 hours, the bike will be faster! Use a fuel / oil mixture of 32:1 for the full 8 hour break-in period. Be sure to use high-octane pump gas, with Cobra’s specially formulated Cobra Venom 2-cycle Race Oil . (Part # MCMUOL02) CAUTION: Failure to use proper fuel, oil, or fuel/oil mixture may result in premature engine wear or damage to the machine. Adhering to the following break-in schedule will result in long lasting high performance machine. • Start bike on stand • First 5 minute period, operate the bike on the stand with a combination of idle and high RPM operation. (avoid prolonged high RPM but spin the rear wheel good at least once or twice per minute) • Allow bike to cool • Ride for 15 minutes maximum (avoid prolonged high RPM operation and avoid abusing the clutch with throttle blipping. • Cool and inspect bike for loose fasteners. • Next ½ hour of operation, avoid prolonged operation at Wide Open Throttle. • After 1 hour of operation o Check for loose bolts and nuts on the bike and retighten as necessary (proper toque values are listed under Specifications). o Clean the carburetor bowl. o Change the transmission / clutch lubricant. • After 8 hours of operation o Change the fork oil. o Have a Certified Cobra Mechanic change the shock oil. • Your bike is now ready for the highest level of competition! NOTE: During break-in the bike will likely lose some engine coolant through the radiator overflow hose. Losing up to 4 oz (120 ml, ½ cup) is normal. Proper coolant level will cover the top of the radiator cores. Removing the radiator cap and looking inside is the only way to check the coolant level. 8
Never open the radiator cap of a machine that has a hot or warm engine or one that has recently been ridden. Burning and scalding could occur. CAUTION: It is important that the radiator cap is installed correctly and completely otherwise engine damage could occur. Starting Procedure Before starting the machine inspect the following: • Check for proper tire pressure in both tires. • Observe the chain tension and adjust if necessary. • Observe the coolant level and fill if necessary. • Verify that the chain rollers and sliders do not have improper wear. • Verify that the handlebars are tight. • Check the throttle for smooth operation and that it ‘clacks’ shut properly. • Check for loose bolts and nuts, and re-torque as necessary. • Verify that the air filter is clean and properly saturated with oil. • Insure that the fuel tank contains an adequate volume of fuel / oil mixture to complete the distance required. (High octane pump gas with Cobra’s specially formulated Cobra Venom 2-cycle Race Oil ) • Turn the fuel on by rotating the fuel petcock knob to the vertically downward position (reserve position is horizontally forward) CAUTION: For best results from your Cobra Motorcycle use only the recommended fuels. Testing has shown that most ‘race’ fuels actually degrade performance. Always wear a helmet and other protective riding gear. When your pre-ride inspection is complete the bike may be started. For a cold engine follow this procedure. 1. Place the motorcycle on a stand of sufficient strength that positions the motorcycle in a level upright position with the rear wheel off the ground. 2. Pull up the choke knob and turn it to lock it. 3. Kick start the engine. 4. Rev the engine in short spurts, turning the throttle no more than 1/4 open until the engine will run without the choke.

2006-up Harley-Davidson Single Bore Induction System Installation Instructions

0

Filed Under (Harley Davidson) by admin on 10-11-2010

download
Remove the stock fuel induction system, including the manifold and disconnecting all wire connections. It is up to the technician as to whether the gas tank should be removed or just raised up in the rear. Picture 1 2- You will need to disassemble the stock induction system to remove the pre-listed parts for re-use. 3- Verify the new manifold size is appropriate for your motorcycle by sliding it in place. Picture 2 Picture 3 4 5- Slide the MAP sensor in place, being sure not to pinch the orange rubber seal—some clean engine oil may make this easier. Install the cable guide and verify it is aligned with the throttle cable actuator. Once alignment is satisfactory, apply Loctite® 222 to the 10-24 x 1/4″ screws and tighten to 18-22 in-lbs. 4- Install the new O-ring into the throttle body. A light film of clean engine oil can be used to help hold the O-ring in place. Align the manifold to the throttle body, use purple 222 Loctite® on the 10-24 x 1″ socket-head assembly screws (with flat washers) and tighten them to 35-40 in-lbs. 6- Using the new S&S® supplied gasket, slide the S&S supplied intake air temperature (IAT) sensor in place. Use Loctite 222 on the T10 Torx button head M3 x .5 x 10mm screws and tighten to 6-8 in-lbs. Picture 4 Picture 5 Picture 6 5 7- For the stock throttle position sensor attach the “C” shaped spacer to the end of the throttle shaft, put a 4mm flat washer on each T20 Torx button head M4 x .7 x 12mm screw, apply some Loctite® 222 and torque screws to 18-23 in-lbs. 8- Install the new O-ring on the IAC motor. Lubricate the OD of the O-ring with a light film of clean engine oil. Put a 4mm flat washer on each T20 Torx button head M4 x .7 x 12mm screw, coat the threads with Loctite 222. Install the IAC motor and tighten the screws to 18-23 in-lbs. 9- Partially install the fuel injectors in the fuel rail. Be sure to orient the black O-rings to the rail and align the clocking tabs with their holes. It may be helpful to lubricate the O-rings with clean engine oil. See Picture 9. NOTE : These are special O-rings that seal pressurized gasoline. If you see one with damage or an abrasion—replace it immediately. Picture 7 Picture 8 Picture 9 6 10- Connect the Injectors to the manifold with a light squeezing action. Lubricate the O-rings with clean engine oil. Once in place, use Loctite® 222 on the threads of two 8-32 x 5/8″ slotted panhead screws and tighten to 15-20 in-lbs. 11- Install the backing washer and O-ring on the fuel supply tube. Lubricate the O-ring with clean engine oil. When the tube is in place, position the Y-shaped clip on the fuel rail and tighten the Loctite 222 coated T20 Torx button head M4 x 7 x 12mm screw to 18-23 in-lbs – Gently push the injectors downward toward the manifold to increase clearance for connecting the wire connectors. Cut the existing injector connectors from the motorcycle harness. Slide the sleeveing onto the injector harness. Slide heat shrink tubing on to each wire of the injector harness wires. Crimp the butt splices to the motorcycle harness. Move the heat shrinks over the splices and shrink with a heat gun. Slide the sleeve into place. Picture 10 Picture 11a Picture 11b Picture 12 Picture 12a 7 13- Put the stock manifold flanges on the manifold. YOU MUST USE THE S&S® RUBBER GASKETS ON THEM. Be sure to orient the tapered end towards the manifold and the flat end to the heads. 14- Hold the manifold up in its basic mounting position and connect all of the wiring harness connectors at this time. Install the manifold using the stock mounting flange bolts (from the primary side of the motorcycle) coated with Loctite® 242 and the new S&S cam side screws (1/4″ socket head, 5/16-18 x 3/4″). If a screw longer than 3/4″ is used, damage to the heads will result. Lightly snug all four manifold mounting bolts but DO NOT TIGHTEN AT THIS TIME. Connect the throttle cables and cruise control bracket (if applicable) at this time. NOTE: The Harley-Davidson® service manual for your model motorcycle will be helpful during this step. 15- Install the breather system now. On 4.00-inch bore or smaller engines the breather uses banjo fittings with hollow bolts and connects across the heads to the intake with a T-hose. This hose will need to be trimmed and have spring clamps attached as shown in photo. Torque the hollow bolts to 10-12 ft-lbs. On 41/8-inch bore or larger engines, install the sharp bent hose on the rear head and install the check valve with the white end towards the head. Mount the other hose on the black end of the check valve and connect it to the throttle body using spring clamps to secure the connections. Picture 13 Picture 14 Picture 15 8 16- Once the breathers are secure, install the fuel line per the factory service manual you are working with. Connect the battery and verify the fuel pump turns on to pressurize the system and there are no gas leaks, but DO NOT START THE ENGINE. At this time, PC software may also be used to verify sensor readings and adjust the throttle position sensor voltage if necessary. 17- Install two 242 Loctite® coated pipe plugs (included in kit) in the air cleaner backplate as shown in Picture 16. Torque to 35-45 in-lbs. Also, two pan screws coated with Loctite® 222 must be installed in the backplate in place of the enrichment device. See Picture 16a. Torque them to 12-18 in-lbs. Failure to install these screws could allow dirt and debris into the intake system. 18- Use a new gasket on the backplate and put it in place noting the number of shims required. Once you select the appropriate shims (included) mount the backing plate to the engine but DO NOT INSTALL THE SCREWS YET

Incoming search terms:

Incoming search terms: