2006 yz450 top dead center

You search Auto repair manual PDF 2006 yz450 top dead center, if there are search results will appear below. If search results do not exist, please search by others keyword.





2003 – 2006 KTM The e-Axle Installation Manuals

0

Filed Under (KTM) by admin on 01-02-2012

download
Remove the stock wheel spacers from both sides of the wheel hub and install both of the Rekluse wheel spacers. After installing the Rekluse wheel spacers, stow the wheel in a suitable place so that the brake rotor cannot be damaged. See following picture. 5 5. Remove the brake pads by removing the clips and sliding out the pin. See following picture. 6. Remove the leaf spring from the caliper. See following picture. 7. Re-install the brake pads with the included coil spring positioned on the pin between the brake pads. Secure the pin by re-installing the 2 clips. See following picture. Coil Spring on the pin and in between the brake pads 6 8. Coat the center axle in a thin layer of grease to aid in sliding the center axle on and off. Note: Coat the center axle in a thin layer every time it is reinstalled after removing the front wheel for tire maintenance. 9. Position the front wheel back in between the forks so that the brake disk is in place between the brake pads, and so the wheel spacers line up with the hole in the fork fists. 10. Slide the center axle, with 30-mm Bushing attached, through the right-side fork fist and through the wheel spacers in the front hub. Rotate the 30-mm bushing so the set screw is facing up, this will line the “0″ Offset Mark with the fork fist pinch clamp slot. Continue sliding the axle through until the 30-mm bushing is almost flush with the outer edge of the right fork fist. See following picture

Harley-Davidson touring bikes WHEELDOCK EZ-UP Center Stand Installation Instructions

0

Filed Under (Harley Davidson) by admin on 18-04-2012

download
Unlike other center stands, the WHEELDOCK EZ UP stand requires very little effort to operate and can usually be done while still on the bike by simply pushing down on the foot lever with your left foot. Once you feel both feet of the center stand in contact with the ground, transfer your weight up off of the seat and onto the foot lever of the center stand. The stand should rotate under the bike and a bit forward lifting the bike quite easily. CAUTION: Never attempt to raise the bike with a passenger on board, as you will damage the foot lever. You can also raise the bike on the center stand by using the following traditional method: Place the bike on the side stand and step off to the side. From the left side of the bike, push the bike up to the vertical position and press down on the foot lever until both feet of the stand are in contact with the ground. Now apply weight to the foot lever while lifting up on the bike. For cleaning the rear wheel: first place a ½-inch piece of plywood under the stand and use this (beside the bike) method for placing the bike up on the plywood spacer; this will allow the wheel to rotate freely for cleaning. Do not try this while on the bike, as it will require too much foot pressure on the lever. You now have two options to get the bike off of the stand: You can simply rock the bike forward, or put the bike in gear and drive off in most cases as long as you are parked on a flat, level surface. Tips for solving common problems: If you have the correct height stand and you still have difficulty getting the bike up on the stand check the following: the bike must be in neutral, the wheel should be straight forward and not cocked, do not hold the front brake lever and make sure you have 15 lb or more air pressure in the rear suspension. These are the most common problems we encounter.

Incoming search terms:

Harley-Davidson The WHEELDOCK EZ-UP Center Stand Installation MANUAL

0

Filed Under (Harley Davidson) by admin on 21-03-2012

download
Unlike other center stands, the WHEELDOCK EZ UP stand requires very little effort to operate and can usually be done while still on the bike by simply pushing down on the foot lever with your left foot. Once you feel both feet of the center stand in contact with the ground, transfer your weight up off of the seat and onto the foot lever of the center stand. The stand should rotate under the bike and a bit forward lifting the bike quite easily. CAUTION: Never attempt to raise the bike with a passenger on board, as you will damage the foot lever. You can also raise the bike on the center stand by using the following traditional method: Place the bike on the side stand and step off to the side. From the left side of the bike, push the bike up to the vertical position and press down on the foot lever until both feet of the stand are in contact with the ground. Now apply weight to the foot lever while lifting up on the bike. For cleaning the rear wheel: first place a ½-inch piece of plywood under the stand and use this (beside the bike) method for placing the bike up on the plywood spacer; this will allow the wheel to rotate freely for cleaning. Do not try this while on the bike, as it will require too much foot pressure on the lever. You now have two options to get the bike off of the stand: You can simply rock the bike forward, or put the bike in gear and drive off in most cases as long as you are parked on a flat, level surface. Tips for solving common questions: If you have the correct height stand and you still have difficulty getting the bike up on the stand check the following: the bike must be in neutral, the wheel should be straight forward and not cocked, do not hold the front brake lever and make sure you have 15 lb or more air pressure in the rear suspension. These are the most common problems we encounter

Incoming search terms:

Corolla & Matrix 2005 – 2006 1ZZ-FE ENGINE NO START OR EXTENDED CRANK CONDITION

0

Filed Under (Toyota Manuals) by admin on 29-05-2011

Download
Some 2005 and 2006 model year Corolla and Matrix vehicles equipped with a 1ZZ–FE engine may exhibit a “no start” or “extended crank” condition. This may be caused by insufficient fuel pressure after the vehicle has been parked for a period of time. The fuel pump assembly manufacturing process has been improved to correct this condition. Applicable Vehicles S 2005 – 2006 model year Corolla and Matrix (2WD) vehicles equipped with the
1ZZ–FE engine. Parts Information PREVIOUS PART NUMBER 77020–02180 77144–04010 77169–02050 CURRENT PART NUMBER Same Same Same PART NAME Fuel Suction w/Pump & Gauge Tube Assembly Fuel Pump Gauge etainer
Fuel Suction Tube Set Gasket

2004 – 2006 4Runner TIRE PRESSURE SENSING TRANSMITTER ACTIVATION PROCEDURE DURING PDS

0

Filed Under (Toyota Manuals) by admin on 29-10-2011

download
pressure data is transmitted through a Tire Pressure Warning System antenna to the Tire Pressure Monitoring System receiver. The tire pressure sensing transmitter used for the Tire Pressure Monitoring System (TPMS) on 2004 – 2006 model year 4Runner vehicles needs to be activated during Pre-Delivery Service (PDS). 2004 – 2006 model year 4Runner vehicles. NOTE: After all the tire pressure sensing transmitters are activated, the flashing Low Tire Pressure Warning Light goes OFF. The Diagnostic Trouble Codes (DTCs) listed below may be stored in the system until the tire pressure sensing transmitters are activated. The codes will automatically clear when the tire pressure sensing transmitters are activated

Incoming search terms:

HARLEY DAVIDSON FLTR DETACHABLE TOUR-PAK ANTENNA RELOCATION KIT

0

Filed Under (Harley Davidson) by admin on 19-02-2011

download
Drilling Instructions for Antenna Base Mounting and Cable Routing 1. See Figure 1. Measure and determine the center of the outside rear Tour-Pak wall. 2. Lay a strip of 2 inch wide masking tape from top to bottom over the approximate center. 3. Very carefully measure again and mark the center near the top of the tape strip. Measure and mark the center near the bottom of the strip. 4. Draw a line from the top mark to the bottom mark. 5. Facing the centerline you have drawn, measure 9-1/4 inches from the center line to the left side. 6. At the 9-1/4 inch dimension, lay a vertical strip of 2 inch masking tape from the top to approximately the middle of the Tour-Pak wall. 7. Very carefully measure again and mark 9-1/4 inches from the top of center line to the top of the tape strip. Measure and mark 9-1/4 inches from the bottom of the center line to the bottom of the strip. 8. Draw a vertical line from the top mark to the bottom mark. 9. Measure 1-1/4 inches from the top edge, down the vertical line you have drawn and draw a short horizontal line across the vertical line. 10. Measure 1-1/2 inches down the vertical line you have drawn from your FIRST short horizontal line and draw another short horizontal line across the vertical line

HONDA GL1500 Headlamp Adjustments Manual

0

Filed Under (Honda) by admin on 08-04-2011

download
Headlamp Adjusting Procedure Tools needed • Long, slender #1 Phillips screwdriver (for adjusters behind the rubber plugs) • #2 Phillips screwdriver (for the other adjuster screw) • 12-inch square of cardboard • Flat wall or garage door • Paper, tape, marker NOTE: All adjustments are very fine. You have to turn the screws A LOT to see changes in adjustment. This procedure is best done after dark, because you will need to do some test rides. Preparation 1. Set the bike on its center stand, 10 feet away from an unobstructed wall or garage door, and square to the wall or door. 2. Remove the front fairing cover and lower vent grille to gain access to the headlamp adjusters. 3. Idle the engine or connect a battery charger to the battery, to prevent battery drain. Headlamp assembly viewed from the front, showing positions of mirrors and adjusters (pretend the lens has been removed) . Low Beam Vertical Alignment 1. With the lights on low beam, cover the right half of the lamp assembly with the cardboard square, so only the left bulb is shining on the wall. 2. Using a marker, mark the top of the left low beam on the wall (use paper taped to the wall if you don’t want to mark the wall itself) . 3. Move the cardboard so it blocks the left bulb, so only the right bulb is shining on the wall. 4. The top of the right low beam should be even with the mark you made for the left low beam. If it’s not, adjust by turning the screw behind the rubber plug at the top of the lamp assembly, using a long, slender #1 Phillips screwdriver. 5. Move the cardboard back and forth between the bulbs to verify that the low beams are at the same height. On high beam, the two hotspots should line up vertically. High Beam Vertical Adjustment 1. With the lights on high beam, note the position of the beams’ hot spots on the wall in relation to the mark you made in step 5 above. 2. Most owners complain about their low beams being too low on the roadway. To correct this, lower the high beams by turning the screw behind the rubber plug at the bottom of the headlamp assembly, using a long, slender #1 Phillips screwdriver. You can watch the high beam hot spot being lowered on the wall in relation to the mark you made. 3. Take a test ride. Get out on a dark street, and adjust the high beams using the dash knob until you like what you can see. Then switch to low beam and see how that looks. 4. Repeat these steps until you get the low beam pattern you want. Left/Right Adjustment 1. Back to the wall. Set the bike on its center stand at a distance of 25 feet from the wall and square to the wall. Center the front wheel. 2. Shine the high beams on the wall. 3. Step to the back of the bike, and level your eye with the center of the passenger backrest. Use the center of the backrest and the center of the windshield like a gunsight. The center of the hotspot of the high beam should hit the wall in this line. 4. Adjust by turning the uncovered screw at the bottom of the headlamp assembly, using a #2 Phillips screwdriver.

Incoming search terms:

2006 Honda GL1800 AirbagCB Radio Squeal REPAIR PROCEDURE

0

Filed Under (Honda) by admin on 08-04-2011

download
To remedy this problem, a ferrite core harness kit is now available for installation. 2006 GL1800 VIIIA (Airbagmodels) with optional CBRadio. Install a ferrite harness core kit according to the installation instructions that are packaged with the kit. ÒÑÌÛæ • The kit includes both a rider and a passenger harness; it’s necessary to install both harnesses to eliminate the squealing noise. • Passengers must route the headset cord as shown. If routed otherwise, it will be too close to the motorcycle’s antenna, which can create an interference. Subharness installation can be confirmed by removing the left-side fairing pocket, and check- ingtoseeifthe harness is already installed. Ferrite CoreHarness Kit (1 required) P/N: 08E95-MCA-100WA H/C: 8607665 ÒÑÌÛæCallTechLineat (800) 421-1900 to order parts. Due to the limited number of affected units and parts availability, ordering will be controlled until May 31,2007. Normal warranty claim submission require- mentsapply. Submit one claim per VIN. Template: GL19 Flat RateTime: 0.3 hours

2006 TRIUMPH SPEED TRIPLE ALUMINUM, CARBON FIBER, SLIP-ON EXHAUST SYSTEM INSTALLATION

0

Filed Under (Triumph) by admin on 30-10-2010

download
1) Place the motorcycle in a vise or on it’s stand and make sure it is safe and secure. 2) Remove the right side muffler heat shield. Loosen the right side muffler inlet clamp. Remove and retain the muffler mounting bolt and nut. Remove the right side muffler from the motorcycle. 3) If the gasket remained on the stock muffler inlet tube, remove it and inspect. Replace if necessary and then install onto the Jardine muffler inlet tube. 4) Slide the Jardine muffler into the stock s-bend outlet. 5) Attach the rubber strip to the inside of one supplied muffler clamp. Slide the muffler clamp over the muffler withe the offset facing inward. Squeeze both muffler clamp tabs together and secure it to the muffler mounting bracket using the original bolt and nut. Do not fully tighten yet. 6) Adjust the muffler so it is straight and fully tighten the t-bolt clamp, then the muffler clamp hardware. 7) Repeat steps #2-6 for the left side muffler. 8) Clean all fingerprints from the muffler. Start the motorcycle and check for any exhaust leaks. Ratchet 12mm Socket 12mm Wrench Spring Tool or Needlenose Pliers 2 – Mufflers (Left & Right) 2 – Muffler Clamps 2 – Rubber Strips SLIP-ON EXHAUST SYSTEM TRIUMPH SPEED TRIPLE 2006 18-7008-123-02 ALUMINUM 18-7008-323-02 CARBON FIBER PERFORMANCE DELIVERED! All Jardine products are warranted against defective materials and workmanship for a period of 90 days from date of original consumer purchase. Any non-defective item may be returned within 7 working days, and will be subject to a 20% restocking/repackaging fee. WHATIS WARRANTED: Any Jardine product returned, with prior approval, for defective materials or workmanship including chrome blistering, peeling, bubbling, or any unused (new) Jardine product with rust damage

2006 Model Engine Oil Recommendation Chart

0

Filed Under (KTM) by admin on 26-11-2010

download
2006 Model Type Recommended Engine Oil Type Quantity SPORTMINICYCLES AC 50 MINI ADVENTURE Motorex ATF Super (Dexron II Gear Oil) 0.15-0.2 L 50 SENIOR ADVENTURE Motorex ATF Super (Dexron II Gear Oil) 0.15-0.2 L SPORTMINICYCLES LC 50 SX JUNIOR Motorex Top Speed 4T 15W50 0.15-0.2 L 50 SX Motorex Top Speed 4T 15W50 0.15-0.2 L 65 SX Motorex Top Speed 4T 15W50 0.3L SX 2 STROKE 85 SX Motorex Top Speed 4T 15W50 0.5 L 105 SX Motorex Top Speed 4T 15W50 0.5 L 125 SX Motorex Top Speed 4T 15W50 0.7 L 250 SX Motorex Top Speed 4T 15W50 0.7 L SX 4 STROKE 250 SX-F Motorex Power Synt 4T 10W50 1.1 L 450 SX Motorex Power Synt 4T 10W50 1.25 L 525 SX Motorex Power Synt 4T 10W50 1.25 L CROSS COUNTRY 2 STROKE 200 XC Motorex Top Speed 4T 15W50 0.7 L 200 XC-W Motorex Top Speed 4T 15W50 0.7 L 250 XC Motorex Top Speed 4T 15W50 0.7 L 250 XC-W Motorex Top Speed 4T 15W50 0.7 L 300 XC Motorex Top Speed 4T 15W50 0.7 L 300 XC-W Motorex Top Speed 4T 15W50 0.7 L CROSS COUNTRY 4 STROKE 450 XC Motorex Power Synt 4T 10W50 1.25 L 525 XC Motorex Power Synt 4T 10W50 1.25 L ENDURO RACING 400 EXC Motorex Power Synt 4T 10W50 1.25 L 450 EXC Motorex Power Synt 4T 10W50 1.25 L 525 EXC Motorex Power Synt 4T 10W50 1.25 L ADVENTURE LC8 950 Adventure orange Motorex Power Synt 4T SAE 10W50 (for temperatures over 32° F) and 5W40 (for temperatures under 32° F) Approx. 3.0 L 950 Adventure black Motorex Power Synt 4T SAE 10W50 (for temperatures over 32° F) and 5W40 (for temperatures under 32° F) Approx. 3.0 L 950 Adventure S Motorex Power Synt 4T SAE 10W50 (for temperatures over 32° F) and 5W40 (for temperatures under 32° F) Approx. 3.0 L SUPERMOTO RACING 450 SMR Motorex Power Synt 4T 10W50 1.25 L 560 SMR Motorex Power Synt 4T 10W50 1.25 L SUPERMOTO LC4 625 SMC Motorex Power Synt 4T 10W50 Approx. 2.1 SUPERMOTO LC8 950 Supermoto orange Motorex Power Synt 4T SAE 10W50 (for temperatures over 32° F) and 5W40 (for temperatures under 32° F) Approx. 3.0 L 950 Supermoto black Motorex Power Synt 4T SAE 10W50 (for temperatures over 32° F) and 5W40 (for temperatures under 32° F) Approx. 3.0 L