2007 crf 450 cam lobe position

You search Auto repair manual PDF 2007 crf 450 cam lobe position, if there are search results will appear below. If search results do not exist, please search by others keyword.



  2007 crf 450 cam lobe position Direct Download speed 5282 Kb/s

  2007 crf 450 cam lobe position Full Version speed 6162 Kb/s



Yamaha YZ 250F Camshafts REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Yamaha) by admin on 30-12-2011

download
Remove the 4 bolts that hold the exhaust cam cap in place, lift the cam cap off. It may be necessary to pry very lightly on the cap to lift it off its dowel pins. Do not use the cam lobes as the pry point. Be careful not to drop the dowels and also be careful to not lose the half moon shaped retainer for the bearing under the cam cap. Remove the 6 bolts that hold the intake camshaft cap and lift the cam cap off the camshaft, again, be careful to not drop the retainer or dowels. Lift the intake camshaft out of its pocket in the cylinder head casting. Remove the cam chain from the sprocket, set the stock camshaft aside. Lift the exhaust cam out of its pocket in the cylinder head casting and remove the chain from the sprocket. Do not drop the cam chain, dangle it over the side of the engine while keeping slight upward pressure on the chain to maintain its position on the drive sprocket on the crankshaft. Fit the half moon shaped retainers in the grooves of the Hot Cams camshaft bearings to ensure good fit, set retainers aside for the time. Using assembly lube, lube the shim buckets, bearing surfaces for the camshafts in the cylinder head, and pack some in the camshaft bearings. Set the exhaust cam into the cylinder head casting while at the same time fitting the cam chain over the sprocket. Make sure that you keep all the cam chain slack to the back of the engine. The cam chain pulls the camshaft sprockets in a counter clockwise direction and the slack of the chain must be kept on the cam chain tensioner side of the engine. The exhaust cam has two timing marks on it. When correctly installed one mark will be at the 9 o’clock position and the other mark will be at the 12 o’clock position. When correctly timed the mark at 9 o’clock will be aligned with the valve cover gasket surface. Repeat the above process for the intake camshaft. Again, make sure you keep the chain slack to the cam chain tensioner side of the engine. Check to be sure the crankshaft is still at TDC. The intake cam has two timing marks also. One at 12 o’clock and the other at 3 o’clock. When both cams are installed correctly, the valve cover gasket surface will form a straight line through the exhaust timing mark at 9 o’clock and the intake timing mark at 3 o’clock

Incoming search terms:

2007 KTM 250 SX-F 450 SX-F INSTALLATION MANUAL

0

Filed Under (KTM) by admin on 06-02-2012

download
Clutch lever The clutch lever [1] is located on the left side of the handlebar. The adjusting screw [A] is used to change the original position of the clutch lever (see maintenance work on chassis and engine). The clutch is hydraulically actuated and adjusts itself automatically. Hot start lever If you pull the red hot start lever [2] during the starting procedure backward, a bore in the carburetor will be opened through which the engine may take in additional air. The result is a “lean” fuel-air mixture of the type needed for hot starts. 2 1 A Fuel tap OFF In this position the fuel tap is closed. No fuel can flow to the carburetor. ON During operation the twist grip must be turned to ON. This means that the fuel can flow to the carburetor. OPERATION INSTRUMENTS »
Starter button (450 SX-F) Pushing the black starter button [3] will actuate the E-starter. ENGLISH 6 Hand brake lever The hand brake lever [1] is mounted on the handlebars on the right and actuates the front wheel brake. The adjusting screw [A] can be used to change the basic position of the hand brake lever (see “Maintenance”). Short circuit button The short circuit button [2] turns off the engine. When pressing this button, the ignition circuit is short-circuited. Filler cap To open the filler cap: Turn the filler cap 45 ° counter-clockwise. To close the filler cap: Put the filler cap on and turn it 45 ° clockwise. OFF ON 1 A 2 3 ENGLISH 7 OPERATION INSTRUMENTS » Choke If you pull the choke button [1] out as far as possible, a bore in the carburetor will be opened through which the engine may take in additional fuel. The result is a “fat” fuel-air mixture of the type needed for cold starts. To deactivate the choke, push the choke button back into its basic position. Shift lever The shift lever is mounted on the left side of the engine. The position of the gears is shown in the illustration. Neutral is located between first and second gear. Kickstarter (250 SX-F) The kickstarter is mounted on the right side of the engine. Its upper part can be swivelled. Foot brake pedal The foot brake pedal is located in front of the right footrest. Its basic position can be adjusted to your seat position (see maintenance work). Plug in stand The plug-in stand can be attached to the wheel spindle on the left side of the motorcycle

Incoming search terms:

Yamaha YZ400/426F Camshafts REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Yamaha) by admin on 01-01-2012

download
Cleanliness is always a good place to start. Make sure the motorcycle is cleaned thoroughly before you start. It would be advisable to use an engine degreaser on the frame and the engine. This will ensure a clean engine during the assembly process and less of a chance of thread damage and/or dirt contamination in the engine during reassembly. And as always, replace any fiber-based gasket that was moved in any way, i.e.: cam chain tensioner. You will need basic hand tools and a torque wrench, machine towels (rags), some cleaning solvent, and a cam chain tensioner gasket. And the Hot Cams’ Degree Wheel Kit if you so desire. We will start by removing the tank and seat, top engine mount, and the cam cover. Remove the crankshaft cap and timing hole cap on the left engine case cover. Remove the spark plug. Rotate the engine in a counter clockwise (CCW) direction. Position the engine on top dead center (TDC) using the mark on the flywheel or better yet a degree wheel using a positive stop. Be sure to notice that the intake valves were the last to move, this will ensure the engine of being on “true” TDC. True top dead center occurs when both the intake and exhaust valve are closed when the piston is at TDC. This is technically the end of the compression stroke and the Page 1
beginning of the power stroke. The “artificial” TDC is during the overlap when both the intake and exhaust valves would be open. Note the positioning of the cam lobes (their included angle will be close to 170 degrees), this will help during the installation of your new Hot Cams camshafts Remove the cap bolt on the end of the cam chain tensioner block, be aware of the copper washer. Release the spring tension on the cam chain tensioner by turning the flat blade screw slot inside the adjuster block in a clockwise (CW) direction; it will lock in the retracted position. Remove the two 8mm headed bolts that hold the cam chain tensioner to the cylinder block. Remove and discard the gasket. Remove the 4 bolts that hold the exhaust cam cap in place, lift the cam cap off. It may be necessary to pry very lightly on the cap to lift it off its dowel pins. Do not use the cam lobes as the pry point. Be careful not to drop the dowels and also be careful to not lose the half moon shaped retainer for the bearing under the cam cap. Remove the 6 bolts that secure the intake cam cap and lift the cam cap off the camshaft, again, be careful to not drop the retainer or dowels. Lift the intake camshaft out of its pocket in the cylinder head casting. Remove the cam chain from the sprocket, set the stock camshaft aside. Lift the exhaust camshaft out of its pocket in the cylinder head casting and remove the chain from the sprocket. Do not drop the cam chain, dangle it over the side of the engine while keeping slight upward pressure on the chain to maintain its position on the drive sprocket on the crankshaft

Incoming search terms:

SUZUKI SV 1000 RADIATOR (COOLING SYSTEM) SERVICE MANUAL

0

Filed Under (Suzuki) by admin on 26-02-2011

download
FI SYSTEM MALFUNCTION CODE AND DEFECTIVE CONDITION MALFUNCTION CODE DETECTED ITEM DETECTED FAILURE CONDITION CHECK FOR COO NO FAULT C11 Camshaft position sen- sor The signal does not reach ECM for more than 3 sec . after receiving the starter signal . The camshaft position sensor wiring and mechanical parts (Camshaft position sensor, intake cam pin, wiring/coupler con- nection) C12 Crankshaft position sensor The signal does not reach ECM for more than 2 sec . after receiving the starter signal . The crankshaft position sensor wiring and mechanical parts (Crankshaft position sensor, wiring/coupler connection) C13 Intake air pressure sensor The sensor should produce following voltage . (0.50 V < sensor voltage < 4 .85 V) Without the above range, C13 is indicated. Intake air pressure sensor, wiring/coupler connection C14 Throttle position sen- sor The sensor should produce following voltage . (0.20 V < sensor voltage < 4 .80 V) Without the above range, C14 is indicated. Throttle position sensor, wiring/coupler connection C15 Engine coolant temperature sensor The sensor voltage should be the following. (0.15 V <_ sensor voltage < 4 .5 V) Without the above range, C15 is indicated. Engine coolant temperature sensor, wiring/coupler connection C21 Intake air temperature sensor The sensor voltage should be the following. (0.15 V < sensor voltage < 4 .5 V) Without the above range, C21 is indicated. Intake air temperature sensor, wiring/coupler connection C22 Atmospheric pressure sensor The sensor voltage should be the following. (0.50 V < sensor voltage < 4 .5 V) Without the above range, C22 is indicated. Atm. pressure sensor, wiring/coupler connection C23 Tip over sensor The sensor voltage should be the following for more than 2 sec . after ignition switch turns ON . (0 .20 V < sensor voltage < 4 .80 V) Without the above value, C23 is indicated. Tip over sensor, wiring/coupler connection C24 or C25 Ignition signalCrankshaft position sensor signal is produced and ECM determines the ignition signal but signal from ignition coil is interrupted continuous by 4 times or more. In this case, the code C24 or C25 is indicated. Ignition coil, wiring/coupler connection, power supply from the battery SERVICING INFORMATION 8 .3 C28 Secondary throttle valve actuator No operating voltage is supplied from the ECM, C28 is indicated. STVA can not operate. STVA lead wire/coupler, STVA C29 Secondary throttle valve position sensor The sensor should produce following voltage . (0.10 V < sensor voltage < 4 .90 V) Without the above range, C29 is indicated . Secondary throttle position sensor, wiring/coupler connection C31 Gear position signalGear position signal voltage should be higher than the following for more than 2 seconds. (Gear position switch voltage >_ 0 .6 V) Without the above value, C31 is indicated. Gear position sensor, wiring/coupler connection, gearshift cam, etc. C32 or C33 Fuel injector Crankshaft position sensor signal is produced and ECM determines the injection signal but fuel injection signal is interrupted continuous by 4 times or more. In this case, the code C32 or C33 is indicated. Injector, wiring/coupler connection, power supply to the injector C41 Fuel pump relay No voltage is applied to fuel pump although fuel pump relay is turned ON, or voltage is applied to fuel pump although fuel pump relay is turned OFF . Fuel pump relay, connecting lead, power source to fuel pump relay C42 Ignition switchIgnition switch signal is not input in the ECM . Ignition switch, lead wire/coupler C44 Heated oxygen sensor (HO2S) [For E-02, 19] During 02 feedback control, 02 sensor voltage is higher or lower than the specification . No signal is detected during engine operation or no electrical power is supplied from the battery . HO2S lead wire/coupler connection Battery voltage supply to the HO2S C49 PAIR control solenoid valve (PAIR valve) When no operating voltage is supplied from the ECM, C49 is indicated. PAIR valve can not operate. PAIR valve lead wire/coupler

Incoming search terms:

HARLEY DAVIDSON HYBRID CAM PLATE AND HIGH FLOW OIL PUMP KIT REMOVAL AND INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 07-02-2011

download
REMOVAL To prevent accidental vehicle start-up, which could cause death or serious injury, disconnect battery cables (negative (-) cable first) before proceeding. (00307a) Disconnect negative (-) battery cable first. If positive (+) cable should contact ground with negative (-) cable connected, the resulting sparks can cause a battery explosion, which could result in death or serious injury. (00049a) 1. Refer to the service manual and follow the instructions to remove the seat and disconnect the battery cables, negative (-) cable first. Retain all seat mounting hardware. Gasoline can drain from the carburetor fuel line when disconnected from fuel valve fitting. Gasoline is extremely flammable and highly explosive, which could result in death or serious injury. Wipe up spilled fuel immediately and dispose of rags in a suitable manner. (00256a) NOTES Installing this kit requires removal and installation of the cam support plate. Refer to the service manual for instructions with the following exception pertaining to cam compartment compo- nents: The crank and primary cam sprocket flange bolts are specially hardened, and the flat washers are of a special diameter and have ground surfaces. Use ONLY the parts provided in the Drive Gear Retention Kit (H-D Part Number 25533-99A, sold separately) when installing this kit. -J04804 1 of 7
The cr ank sprocket flange bolts and pr imary cam sproc ket flange bolts ARE NOT interchangeable. 2. Refer to the service manual to remove and discard the crank sprocket flange bolts and primary cam sprocket flange bolts and washers. 3. For 1999 models only: Refer to the service manual to remove and discard the currently installed cam drive sprocket. 4. Refer to the service manual to remove and disassemble the cams from the support plate and oil pump. Discard the support plate and oil pump. 5. For 1999 – 2000 Dyna, 2000 Softail, 1999 – 2000 Touring, and 2001 EFI Touring models only: Inspect the cams, chain, sprockets and chain tensioners for wear, and replace as needed. Refer to the service manual for inspection and replacement procedures. For 2001 – 2005 Dyna, 2001 – 2006 Softail, 2002 – 2006 Touring, and 2001 carbureted Touring models only: Inspect the cams and secondary cam chain for wear, and replace as needed. Refer to the service manual for inspection and replacement procedures. The primary cam chain, primary sprockets and both tensioners will be replaced by new components from the kit. For ALL models and years: Discard the guide, as it will not be used. INSTALLATION 1. ALL models: See Figure 1. Obtain the new Rear Cam Roller Bearing Kit (H-D Part Number 8983) from inside the Cam Service Kit (H-D Part Number 17045-99C, purchased separately), and install as indicated in Step 2. NOTE See Figure 2. If not enough of the splined shaft is exposed to install the sprocket, omit the spacer (4) and proceed to Step 2e. When the bearing inner race is started onto the machined area, remove the flange bolt (5), flat washer (6) and sprocket, then assemble using the spacer (4). Repeat Step 2e to fully install bearing inner race. To center thrust washer, be sure o-ring is installed in relief groove. Damage to bearing cage and engine can occur if thrust washer is not centered. (00473b) 2. See Figure 1. Install the O-ring (5), thrust washer (4) and bearing inner race (3) onto the rear camshaft as follows: a. See Figure 2. To properly locate the thrust washer (2), install the O-ring (3) in the grinding relief groove on the splined end of the rear camshaft between the machined area and the secondary cam sprocket.

Incoming search terms:

HARLEY DAVIDSON SOFTAIL FRONT SPOILER KITS INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 09-03-2011

download
This instruction sheet references Service Manual information. A Service Manual for your model motorcycle is required for this installation and is available from a Harley-Davidson Dealer. Kit Contents See Figure 2 and Table 1. INSTALLATION 1. Position the vehicle on a motorcycle lift table. To prevent accidental vehicle start-up, which could cause death or serious injury, remove maxi-fuse before proceeding. (00251a) 2. Refer to the Service Manual and follow the instructions given to remove the Maxi® Fuse. 3. Raise the vehicle on the lift table to allow access to the lower front portion of the frame. 2008+ 2007 7 8 11 3 3 4 4 12 5 5 1 1 9 2 2 10 6 6 9 9 11 13 is02652c 8. 1. Two-pin voltage regulator connector (2007 only) Voltage regulator 2. 9. Voltage regulator attaching screws (2) Cable strap (2 for 2007, 1 for 2008 and later) 10. 3. Lower voltage regulator cover (2007 only) Voltage regulator bracket 4. 11. Bracket screw to engine crankcase (2) Oxygen sensor connector 12. 5. Crank position sensor connector (2007 only) Voltage regulator caddy 6. 13. Voltage regulator caddy cover Horn connectors (some 2008 and later models) 7. Four-pin voltage regulator connector (2007 only) Figure 1. Original Equipment Voltage Regulator  NOTE For 2007 models: The ground wire on the voltage regulator must be re-attached at the original location when re-installing the voltage regulator to ensure adequate ground. 4. For ALL models: See Figure 1. Remove and discard the voltage regulator caddy cover (6) from the regulator bracket (3) and caddy (5). For 2007 models: In addition, remove the lower voltage regulator cover (10). 5. Remove and retain the hex socket head screw (4) at the top left of the bracket For 2007 models: In addition, disconnect the ground wire. Free the cable straps (9) from the regulator bracket, beneath the regulator. 6. Remove the two hex socket head screws with washers (2) retaining the voltage regulator to the bracket. Remove and save the regulator, but discard the screws. 7. Remove and retain the screw (4) at the top right of the regulator bracket. Remove the bracket from the engine. 8. For 2008 and later models: Free the strap (9) that ties the jiffy stand wiring to the voltage regulator bracket. Unfasten the three-way jiffy stand sensor connector and the two-way crank position sensor connector [79] (12) from the T-studs on the back of the regulator bracket (3). Discard the bracket. Disconnect both plugs from the back of the voltage regulator (1). For 2007 models: Unfasten the four-way (7) and two-way (8) voltage regulator connectors from the T-studs on the back of the regulator bracket (3), and discard the bracket. Disconnect the voltage regulator (1) at both connectors. 9. For 2008 and later models: Unclip the two-way O 2 (oxygen) sensor electrical connector [138] (11) from the voltage regulator caddy (5). For 2007 models: Unfasten the two-way crank position sensor connector [79] (12) from the voltage regulator caddy (5). Remove the caddy from the vehicle frame. a. For 2007 models: Unclamp the bottom of the caddy from the engine mount spacers. b. For ALL models: Unhook the top clips from around the tabs on the front of the engine casting. Remove the original equipment (O.E.) caddy from the vehicle frame, and discard it.

Incoming search terms:

HONDA 2008 CRF 450 F SLIP-ON EXHAUST SYSTEM REPAIR MANUALS

0

Filed Under (Honda) by admin on 25-12-2011

download
The Akrapovic Slip-On system is designed for recreational Honda CRF 450 enthusiasts. It delivers an excellent combination of quality, performance, visual enhancement, easy installation and affordability. The Akrapovic Slip-On is designed for two markets; in the US it is available with an approved spark arrester, and for the EU and other non-US markets it comes with a noise damper. PERFORMANCE Measurements of the Akrapovic SLIP-ON system on the HONDA CRF 450 R (with muffler insert): Power & Torque: Up to 5600 rpm the Akrapovic Slip-On essentially follows the stock power and torque curves. It shows its true colors above that range, where it delivers significant increases to both power and torque. Max. increased power of 2.8 HP was measured at 6600 rpm. At the top of the rpm range the Akrapovic curves again follow the stock power and torque curves. CONFIGURATION The system is composed of a flared stainless steel link pipe which is welded to the muffler. It is attached to the stock header assembly with a sleeve joint secured with a metal clamp. The muffler is the offroad design with a titanium outer sleeve, and stainless steel inlet cap, outlet cap and inner perforation. The muffler is attached to the frame using an Akrapovic carbon-fiber clamp. In the US the system is available with an approved spark arrester, and for the EU and other non-US markets it comes with a standard noise damper

Kawasaki KFX KLX 400 Camshafts Installation Instructions

0

Filed Under (Kawasaki) by admin on 25-10-2010

download
Remove the plug bolt from the back of the cam chain tensioner assembly. It is under pressure from the spring. Remove the spring and pin. Remove the bolts and tensioner assembly from the cylinder. Release the lock on the tensioner assembly and push the tensioner rod into the assembly so that it is fully retracted. Remove the eight 5mm Allen headed bolts that hold the cam caps in place. Remove the cam caps; be aware of the locating dowels in the caps to keep them from falling into the engine. It may be necessary to pry very lightly on the caps to lift them off their dowel pins. Do not use the cam lobe as the pry point. Lift the intake camshaft out of its pocket in the cylinder head casting. Remove the cam chain from the sprocket, set the stock camshaft aside. Lift the exhaust cam out of its pocket in the cylinder head casting and remove the chain from the sprocket. Do not drop the cam chain; dangle it over the side of the engine while keeping slight upward pressure on the chain to maintain its position on the drive sprocket on the crankshaft. Using assembly lube, lube the shim buckets and bearing surfaces for the camshafts in the cylinder head. Set the exhaust camshaft into the cylinder head casting while at the same time fitting the cam chain over the sprocket. Make sure that you keep all the cam chain slack to the back of the engine. Repeat the above process for the intake camshaft. Again, make sure you keep the chain slack to the cam chain tensioner side of the engine. Check to be sure the crankshaft is still at TDC. Check the location of the cam lobes. The camshafts are marked, and preset to 108-degree centers. If the lobes are not where they should be, adjust the positioning of the camshaft by rotating the sprocket one tooth on the chain. Do this until it is in the correct position as before you removed the camshafts. Check the positioning of the crankshaft for the TDC mark

Incoming search terms:

Harley-Davidson Twin Cam Engines Cam Chain Drive System Installation and removal MANUAL

0

Filed Under (Harley Davidson) by admin on 27-03-2012

download
Removing the Cam Chain Drive System. NOTES Changing camshafts and cam drives in the 2006-up Harley-Davidson® Twin Cam 88® engines is different than in pervious engines. Procedures require use • of some special tools. Installation should be done by an experienced mechanic with access to factory service manual and required tools. Tighten all fasteners to the correct specifications and in order described. Always use an accurate torque wench. • Incorrect installation can cause engine damage not covered under warranty. CAUTION Failure to install components correctly can result in sudden engine seizure. Engine seizure may result in serous injury to motorcycle operator, passenger, or others. A- Disconnect the battery ground cable to eliminate potential sparks and inadvertently engagement of the starter while working on the motorcycle. B- Remove spark plugs and pushrod cover clips. Collapse the pushrod covers to expose the pushrods. C- Safely elevate and stabilize the rear of the motorcycle. Place the transmission in high gear. Turn the rear wheel to rotate the engine until both lifters and pushrods for either cylinder are at the lowest point on the camshaft (TDC of compression stroke). Both intake and exhaust pushrods for that cylinder will be under pressure from the valve springs and will rotate with light finger pressure. NOTE: 510G camshafts may use stock style non-adjustable pushrods instead of adjustable pushrods. If installing non-adjustable pushrods, disassemble and assemble rocker boxes per H-D® instructions. All other S&S® gear driven cams require installing adjustable pushrods. As a time-saving measure, the stock pushrods can be removed with bolt cutters. Be sure to head caution and warnings of these instructions. D- Cut the pushrods for the cylinder that is at TDC with the bolt cutter and remove the pushrod covers from the engine. Rotate the engine to place the pushrods for the other cylinder at their lowest point. Cut and remove the remaining pushrods. WARNING CAUTION Cutting pushrods with a saw or cutoff wheel may result in debris entering the engine, causing engine damage not covered under warranty. WARNING Cutting pushrods without releasing spring pressure, by rotating the engine until tappets are at the lowest point of travel can result in bodily injury. E- Remove the pushrod covers and lifters form the crankcase. F- Remove engine cam cover and gasket. Secure lifers with a tool made from a large binder clip

Incoming search terms:

2005-2007 KTM MOTORCYCLE REPAIR MANUAL

0

Filed Under (KTM) by admin on 21-11-2010

download
Adjustments -Take notice of the position of the compression adjustment 1 ! -Count the amount of clicks by turning the adjustment screw clockwise till fully closed. -Remove the rubber cap out of the axleclamp. -Take notice of the position of the rebound adjustment 2 ! -Count the amount of clicks by turning the adjustment screw clockwise till fully closed. -For the standard position see setting list. Position of the compression and rebound adjustment -Set the rebound position 1 , see KTM-Owners manual. -Assemble the rubber cap. -Set the compression position 2 , see KTM-Owners manual. 1 2 2-22 Repair manual WP Fork “Closed Cartridge” Art.No.: 3.211.199-E Explanation of the spring preload -Total spring length without the spacers, see chapter inspection of the spring! -Spring length with spacers 1 , see setting list. -Spring with the spacers. 1 . -The spring is assembled in the front fork leg. NOTE: the distance of “B” is less then the length of “A”. A – B = Spring preload A 1 1 B 2-23 Air release screw -Place the motorcycle on the stand. NOTE: the front wheel must be lift of the floor! -Unscrew the air release screw 1 of the screw cap on top of the front fork and tighten after approx. 10 seconds the air release screw. Recommended periodic maintenance and inspection of the 4860 SX/SXS/SMR front fork 1 A 100 liter fuel consumption is equivalent to approx. 15 operating hours Clean dust scrapers (after 1 hour) Bleed fork legs regularly – after every cleaning Check the inner tubes on scratches / leakage Visual check of damaging of the outer-tubes / replace if necessary Complete service without disass. the closed cartridge of the fork Complete service including the closed cartridge of the front fork Dismounting the fork -Place your motorcycle on a stand. -Notice the position of the front fork in the triple-clamps. NOTE: To remove the front fork. Read your KTM Instruction Manual or Workshop Manual. 3-3 Mounting the fork -Clean the innerside of the triple-clamps with brake cleaner. -Slide both fork legs into the triple-clamps. NOTE: Pay attention to the position of the fork legs. Standard riding height! NOTE: The maximum riding height is the level of the second groove! -Tighten the middle bolt of the lower triple clamp to a torque of 17 Nm! -Tighten the first bolt of the lower triple clamp to a torque of 17 Nm! -Tighten the third bolt of the lower triple clamp to a torque of 17 Nm!

Incoming search terms:

Incoming search terms: