2007 softail deluxe starter

You search Auto repair manual PDF 2007 softail deluxe starter, if there are search results will appear below. If search results do not exist, please search by others keyword.





HARLEY DAVIDSON SOFTAIL FRONT SPOILER KITS INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 09-03-2011

download
This instruction sheet references Service Manual information. A Service Manual for your model motorcycle is required for this installation and is available from a Harley-Davidson Dealer. Kit Contents See Figure 2 and Table 1. INSTALLATION 1. Position the vehicle on a motorcycle lift table. To prevent accidental vehicle start-up, which could cause death or serious injury, remove maxi-fuse before proceeding. (00251a) 2. Refer to the Service Manual and follow the instructions given to remove the Maxi® Fuse. 3. Raise the vehicle on the lift table to allow access to the lower front portion of the frame. 2008+ 2007 7 8 11 3 3 4 4 12 5 5 1 1 9 2 2 10 6 6 9 9 11 13 is02652c 8. 1. Two-pin voltage regulator connector (2007 only) Voltage regulator 2. 9. Voltage regulator attaching screws (2) Cable strap (2 for 2007, 1 for 2008 and later) 10. 3. Lower voltage regulator cover (2007 only) Voltage regulator bracket 4. 11. Bracket screw to engine crankcase (2) Oxygen sensor connector 12. 5. Crank position sensor connector (2007 only) Voltage regulator caddy 6. 13. Voltage regulator caddy cover Horn connectors (some 2008 and later models) 7. Four-pin voltage regulator connector (2007 only) Figure 1. Original Equipment Voltage Regulator  NOTE For 2007 models: The ground wire on the voltage regulator must be re-attached at the original location when re-installing the voltage regulator to ensure adequate ground. 4. For ALL models: See Figure 1. Remove and discard the voltage regulator caddy cover (6) from the regulator bracket (3) and caddy (5). For 2007 models: In addition, remove the lower voltage regulator cover (10). 5. Remove and retain the hex socket head screw (4) at the top left of the bracket For 2007 models: In addition, disconnect the ground wire. Free the cable straps (9) from the regulator bracket, beneath the regulator. 6. Remove the two hex socket head screws with washers (2) retaining the voltage regulator to the bracket. Remove and save the regulator, but discard the screws. 7. Remove and retain the screw (4) at the top right of the regulator bracket. Remove the bracket from the engine. 8. For 2008 and later models: Free the strap (9) that ties the jiffy stand wiring to the voltage regulator bracket. Unfasten the three-way jiffy stand sensor connector and the two-way crank position sensor connector [79] (12) from the T-studs on the back of the regulator bracket (3). Discard the bracket. Disconnect both plugs from the back of the voltage regulator (1). For 2007 models: Unfasten the four-way (7) and two-way (8) voltage regulator connectors from the T-studs on the back of the regulator bracket (3), and discard the bracket. Disconnect the voltage regulator (1) at both connectors. 9. For 2008 and later models: Unclip the two-way O 2 (oxygen) sensor electrical connector [138] (11) from the voltage regulator caddy (5). For 2007 models: Unfasten the two-way crank position sensor connector [79] (12) from the voltage regulator caddy (5). Remove the caddy from the vehicle frame. a. For 2007 models: Unclamp the bottom of the caddy from the engine mount spacers. b. For ALL models: Unhook the top clips from around the tabs on the front of the engine casting. Remove the original equipment (O.E.) caddy from the vehicle frame, and discard it.

Incoming search terms:

2007 Softail HARLEY DAVIDSON FUEL PUMP/ FUEL GAUGE SENDING UNIT REMOVAL AND INSTALLATION

0

Filed Under (Harley Davidson) by admin on 30-03-2012

download
1. Remove seat. 1 WARNING 1 WARNING To prevent spray of fuel, purge system of high-pressure fuel before supply line is disconnected. Gasoline is extremely flammable and highly explosive, which could result in death or serious injury. (00275a) 2. Purge the fuel supply line of high pressure gasoline. a. See Figure 4-36. Disconnect the fuel pump fuse from the main wiring harness. b. Start the engine and allow the vehicle to run. c. When the engine stalls, operate the starter for 3 seconds to remove any remaining fuel from the fuel lines. 1 WARNING 1 WARNING To prevent accidental vehicle start-up, which could cause death or serious injury, disconnect negative (-) battery cable before proceeding. (00048a) 3. Disconnect negative battery cable. 4. Remove instrument console. a. All but FXSTD, see Figure 4-37. Remove acorn nut and washer on instrument console to separate console from fuel tank. b. For FXSTD, see 8.26 INSTRUMENT CONSOLE: FXSTD. 5. Disconnect console wiring. Figure 4-36. Fuel Pump Fuse: View From Top Figure 4-37. Acorn Nut And Washer: All But FXSTD s0660x8xx 7526
4-28 2007 Softail: Fuel System HOME 1 WARNING 1 WARNING Gasoline can drain from the crossover line when disconnected from fuel tank. Gasoline is extremely flammable and highly explosive, which could result in death or serious injury. Wipe up spilled fuel immediately and dispose of rags in a suitable manner. (00259a) 6. Drain fuel tank. a. Obtain a short section of hose (5/16 inch I.D.). Insert bolt in one end of hose and install hose clamp to ensure that end is securely plugged. b. See Figure 4-38. Cut clamp (1) from one end of crossover hose (2). Quickly replace crossover hose on fuel tank fitting with open end of short hose while directing flow of gasoline from free end of crossover hose into suitable container. 7. See Figure 4-39. Unplug fuel pump module connector (3) [86]. 8. Remove top plate screws (2) and discard. 9. See Figure 4-40. Pull top plate (2) out of fuel tank enough to expose fuel hose and clamp (1). CAUTION Carefully inspect end of hose for cuts, tears, holes or other damage. Replace hose if any damage is found. Even the smallest hole can cause a reduction in fuel pressure. 10. Cut clamp and remove hose from regulator housing fit- ting.

Incoming search terms:

2007 Harley-Davidson Softail Family Specifications

0

Filed Under (Harley Davidson) by admin on 02-11-2010

download
frame Mild steel tubular frame; rectangular section backbone; stamped, cast and forged junctions; forged fender supports; MIG welded Mild steel tubular frame; rectangular section backbone; stamped, cast and forged junctions; forged fender supports; MIG welded Mild steel tubular frame; rectangular section backbone; stamped, cast and forged junctions; forged fender supports; MIG welded Swingarm Mild steel, round tube sections, forged junctions, MIG welded Mild steel, round tube sections, forged junctions, MIG welded Mild steel, round tube sections, forged junctions, MIG welded Front Fork 41.3 mm telescopic, “beer can” covers 41.3 mm telescopic, “beer can” covers 41.3 mm telescopic, “beer can” covers Rear Shocks Hidden, horizontal-mounted, coil-over Hidden, horizontal-mounted, coil-over Hidden, horizontal-mounted, coil-over Caliper Type 4-piston front and rear 4-piston front and rear 4-piston front and rear Rotor Type: (diameter x width) Patented, uniform expansion rotors Patented, uniform expansion rotors Patented, uniform expansion rotors Front 292 mm x 5.08 mm 292 mm x 5.08 mm 292 mm x 5.08 mm Rear 292 mm x 5.84 mm 292 mm x 5.84 mm 292 mm x 5.84 mm Front (mm) 130 130 130 Rear (mm) 109 109 109 Engine Torque (EU standard EC95/1)5 86 ft. lb / 117 Nm @ 3200 rpm 89 ft. lb / 120 Nm @ 3300 rpm 89 ft. lb / 120 Nm @ 3300 rpm Right 29° 30° 28° Left 26° 28° 26° Battery Sealed, maintenance-free, 12V, 19-amp/hour, 270 cca (per Battery Council International Rating) Sealed, maintenance-free, 12V, 19-amp/hour, 270 cca (per Battery Council International Rating) Sealed, maintenance-free, 12V, 19-amp/hour, 270 cca (per Battery Council International Rating ) Charging Three-Phase, 38-amp system (439W @ 13V, 2000 rpm, 489W max power @ 13V) Three-Phase, 38-amp system (439W @ 13V, 2000 rpm, 489W max power @ 13V) Three-Phase, 38-amp system (439W @ 13V, 2000 rpm, 489W max power @ 13V) Starting 1.2 kW electric with solenoid shift starter motor engagement 1.2 kW electric with solenoid shift starter motor engagement 1.2 kW electric with solenoid shift starter motor engagement Headlamp Headlamp Headlamp Quartz Halogen, 55-watt low beam, 60-watt high beam Quartz Halogen, 55-watt low beam, 60-watt high beam Quartz Halogen, 55-watt low beam, 60-watt high beam Tail/Stop Lights Tail/Stop Lights Tail/Stop Lights 8W/28W (5W/21W) 8W/28W (5W/21W) 8W/28W (5W/21W) Turn Signal Lights Turn Signal Lights Turn Signal Lights 28W (21W) self-canceling 28W (21W) self-canceling 28W (21W) self-canceling Indicator Lamps Indicator Lamps Indicator Lamps High beam, neutral, low oil pressure, turn signals, engine diagnostics, security system6, 6-speed (overdrive), low fuel warnings High beam, neutral, low oil pressure, turn signals, engine diagnostics, security system6, 6- speed (overdrive), low fuel warnings High beam, neutral, low oil pressure, turn signals, engine diagnostics, security system6, 6-speed (overdrive), low fuel warnings Passing Lamps Chrome Vivid Black Vivid Black Vivid Black Black Cherry Pearl Black Cherry Pearl Black Cherry Pearl Deep Cobalt Pearl Black Pearl Black Pearl Pewter Pearl Fire Red Pearl Deep Cobalt Pearl White Gold Pearl Deep Cobalt Pearl Olive Pearl & Vivid Black Suede Blue Pearl & Vivid Black Suede Blue Pearl White Gold Pearl & Vivid Black Black Cherry Pearl & Pewter Pearl Olive Pearl White Gold Pearl & Deep Cobalt Pearl Fire Red Pearl & Black Pearl Pacific Blue Pearl Deep Cobalt Pearl & Pewter Pearl Pewter Pearl Yellow Pearl White Gold Pearl

Incoming search terms:

KTM Starter Gear Maintenance Instructions

0

Filed Under (KTM) by admin on 26-11-2010

download
Checking the electric starter motor for wear -Check Bendix 1 for smooth operation and signs of wear. -Check the sprocket of the electric starter for wear and radial clearance. -Replace O-ring 2 of the electric starter. -Replace gasket 3 . -Check starter idler gear 4 for smooth operation and wear, check that the bearing bushings are seated firmly. Electric starter motor – checking for and adjusting play -Mount the electric starter and the starter idler gear. -Mount the tighten cover 5 . -Move starter idler gear 4 back and forth in the direction of rotation, the maximum play may not exceed half the width of a tooth. -If play is larger, cover 5 must be removed and as many shims 6 with a thickness of 0.10 mm as necessary must be added to eliminate all play. Then remove one shim again. -Check the play again; the maximum play may not exceed more than half of the width of a tooth. 1 2 3 4 5 4 5 6

Incoming search terms:

2007 KTM 250 XC-F, XCF-W, EXC-F 400 XC-W, EXC RACING 450 XC, XC-W, EXC RACING 525 XC, XC-W, EXC RACING 525 XC DESERT RACING INSTALLATION MANUAL

0

Filed Under (KTM) by admin on 05-02-2012

download
Headlamp switch (XC-W) In this model the headlamp is switched on with the pull switch [1] . Flasher switch The flasher switch is a separate unit and is mounted on the left portion of the handlebar. The wire harness is designed in a way that whenever you want to use your bike off-road, you can dismount the entire turn indicator system without affecting the function of the remaining electrical system. Flasher left Flasher right Starter button Pushing the black starter button [2] will actuate the E-starter. Indicator lamps The green control lamp [5] flashes in the same rhythm as the flashing indicator when the indicator is working. The blue control lamp [6] lights up when the high beam is on. ENGLISH 7 2 Emergency OFF switch (EXC Australia) The red emergency-OFF switch [3] is arranged adjacent to the throttle grip. In this position, the E-starter is operational and the engine can be started. In this position, the E-starter and ignition circuits are interrupted.The E-starter cannot be actuated, and the engine will not start, not even if you attempt to start it with the kickstarter. Pushing the black starter button [4] will actuate the E-starter. 3 4 5 6 1 OPERATION INSTRUMENTS » ENGLISH 8 TEST All of the display segments briefly light up for the display function test. WS (wheel size) The display changes and the circumference of the front wheel is briefly displayed in millimeters (2205 mm corresponds to a front wheel circumference of 21″ with production tires). Afterwards the display will return to the previous display mode

Incoming search terms:

HARLEY-DAVIDSON Starter Relay Location Guide

0

Filed Under (Harley Davidson) by admin on 18-04-2012

download
Touring 1998 – 2007 Additional Notes: Relay Location: Under Seat in rubber Boot Battery Connection: Under Seat,Visiable Installation Notes: No Access Issues Factory Relay Type: FULL SIZE Factory Relay Part #: 31504-91A Connection Type: Ground Lug to Battery + Terminial System Relay Replacement: R-S-1 Circuit: Cold C Copywrite 2005 Identity Inv. LLC As of: 11.05 ***2004 – 2007 FLHR series bikes & 2007 FLHX require additional Adaptor AD-1 & DGD-1. Start Relay is in Power Distribution box. Replaces H-D Relay part# 31579-04 Softails 2000 – 2007 Additional Notes: 2000 is when the Softails changed to Twin Cams. Relay Location: Under Seat in covered Power Distribution Box. Battery Connection: Under Seat,Visiable Installation Notes: No Access Issues Factory Relay Type: 1/2 SIZE Factory Relay Part #: 31522-00B Connection Type: Ground Lug to Battery + Terminial System Relay Replacement: R-S-3 Circuit: Cold C Copywrite 2005 Identity Inv. LLC As of: 11.05 Softails 1996 – 1999 Additional Notes: Relay Location: Under Seat in covered Power Distribution Box. Battery Connection: Under Seat,Visiable Installation Notes: No Access Issues Factory Relay Type: FULL SIZE Factory Relay Part #: 31504-91A Connection Type: Ground Lug to Battery + Terminial System Relay Replacement: R-S-1 Circuit: Cold C Copywrite 2005 Identity Inv. LLC As of: 11.05
Dyna 2007 Additional Notes: Relay Location: Under Side Panel Cover. Battery Connection: Replace Batt 15A Fuse with Supplied Fuse Holder Installation Notes: No Access Issues Factory Relay Type: 1/2 SIZE Factory Relay Part #: 31522-00B Connection Type: Tap 12v Fuse (Batt 15A) System Relay Replacement: R-S-3 Circuit: Cold C Copywrite 2005 Identity Inv. LLC As of: 11.05 Dyna 2000 – 2005 Additional Notes: Relay Location: Under Side Panel Cover. Battery Connection: Battery connection is made direct to Battery Buss to right of Relay * see Pic3 Installation Notes: Remove Outer Cover, then Remove 4 bolts holding secondary protector plate in place. Relay is on the upper left. Factory Relay Type: 1/2 SIZE Factory Relay Part #: 31522-00B Connection Type: Ground Lug to Battery Buss + Terminial System Relay Replacement: R-S-3 Circuit: Cold C Copywrite 2005 Identity Inv. LLC As of: 11.05 Pic3 Sportster 2004-2007

Incoming search terms:

HARLEY DAVIDSON SOFTAIL DELUXE SEATS INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 06-03-2011

download
These kits fit 2005 and later FLSTN model motorcycles. Additional Parts Required NOTE A Service Manual for your model motorcycle is available from a Harley-Davidson Dealer. Kit Contents See Figure 3 and Table 1. INSTALLATION 1. Remove existing seat according to Owner’s Manual Instructions. Save all attaching hardware. 2. See Figure 1. Install two flange nuts (1) from kit onto the seat mounting studs. Tighten flange nuts to 5-8 ft-lbs (7- 11 Nm) . 1 is03023 1. Install flange nuts Figure 1. Flange Nut Locations NOTE See Figure 3 for Steps 3-6. 3. Remove two screws (A) and rear mounting bracket (B) from stock seat. Save all hardware. 4. Install the rear mounting bracket (B) removed in Step 3 onto the new seat using the seat bracket screws (A). Tighten screws to 19 in-lbs (2.1 Nm) . 5. Install new seat (1) on the motorcycle by inserting the tab at the front of the seat into the slot at the rear of the fuel tank. After installing seat, pull upward on seat to be sure it is locked in position. While riding, a loose seat can shift causing loss of control, which could result in death or serious injury. (00070b) 6. Fasten rear seat bracket (B) to fender nut using stock mounting screw (C). 7. See Figure 2. To install grabstrap, remove front screw and washer from rear fender support. Install grabstrap with thick washers (1), thin washers (3) and screws (4) from kit. Tighten to 21-27 ft-lbs (28-37 Nm)

2008 Harley Davidson Softail Deluxe Exhaust Installation Supplement to Installation Manua

0

Filed Under (Harley Davidson) by admin on 16-02-2011

download
1. Install LH and RH passenger foot peg mount using 3/8×2-1/4″ hex head bolts, 3/8″ SAE flat washers, 3/8″ lock was and 1″ spacers between the motorcycl frame and mount. Figure 1 hers e xhaust ter) n’t Cut 6-1/4″ from end Cut 1/2″ from end Figure 2 2. Remove exhaust chrome covers from header pipes. 3. It is not necessary to remove the front cylinder’s front cover. Remove header pipes from cylinder heads. Cut pipes as shown in Figure 2. 4. Replace header pipes Cut cover 5-5/8″ from end – Shown already cut Figure 3 5. Cut top cover as shown in Figure 3. 6. Install supplied extension pipes as shown in Figure 3 using the OE e clamps. (Clamps covered by covers in picture – covers will be installed la Rotate clamps to make sure they don’t interfere with the foot peg mounts. Do tighten clamps yet. 7. Mount exhaust hanger bracket to body frame with (3) supplied vibration mounts. Figure 4. Figure 4 8. Install supplied clamps to ends of mufflers and fit over exhaust extensions. 9. Attach exhaust pipes to hanger bracket with OEM hardware (4 bolts). Apply Red Loctite to OEM bolts. Figure 4. 10. Install all chrome covers 11. Tighten all exhaust clamps. Figure 5 12. Install supplied chrome cover with clamp removed from cut OE chrome cover. Supplied cover slips over OE chrome cover. Push cover forward to prevent the body from hitting the cover. Figure 5. 13. Move OE clamp backwards and install 14. Position luggage rack as shown in figure 5. Install luggage rack with OE bolt in the Figure 6 Bracket OE Bolt Clamp Figure 7 Drill ¼” holes bracket using OE bolt and supplied 3/8″ bolt. Figure 6. 7 and drill two ¼” holes in shock tower mount. 1 rear and the supplied ¼” bolts in the front.

HARLEY DAVIDSON SOFTAIL DETACHABLE SADDLEBAG KITS INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 22-03-2011

download
Detachable Saddlebag Configurations Table 1 provides a short description of the detachable saddlebag configurations. Table 1. Softail Detachable Saddlebag Configurations Accessory Configuration (Long Description) Short Descrip- tion Kit 2003-Later FLST/C and 2003-2005 FX Softail Models (Except FXSTD) With Other Detachable Accessories FL Outer 88237-07 2003-Later FLST/C and 2003-2005 FX Softail Models (Except FXSTD) Without Other Detachable Accessories FL Inner 2003-Later FLST/C and 2003-2005 FX Softail Models (Except FXSTD) With Rigid-Mounted Accessories FL Rigid 2006-Later FX Models (Except FXSTD) With Other Detachable Accessories FX Outer 88238-07 2006-Later FX Models (Except FXSTD) Without Other Detachable Accessories FX Inner 2006-Later FX Models (Except FXSTD) With Rigid-Mounted Accessories FX Rigid 2007-Later FXSTC Models With Stock Passenger Upright FXSTC Stock NOTE Proper installation of these kits requires that tasks be completed for one side of the motorcycle first before continuing to the opposite side. Install Turn Signal Relocation Kit Refer to instructions included with Turn Signal Relocation Kit 69857-07. Install Docking Hardware Kit(s) Without Other Detachable Accessories: Refer to instructions included with Docking Hardware Kit 53932-03. With Other Detachable Accessories: Refer to instructions included with Docking Hardware Kits 53932-03 and 88256-07. Install Rear Docking Adapter NOTE This procedure only applies to models without detachable accessories. 1. See Figure 1. Insert rear docking adapter (1) into holes in saddlebag bracket and hold in place. 2. Install rear docking adapter using screw (2) and nut (3). Tighten snugly.

Incoming search terms:

2006 – 2007 Harley-Davidson Softail Ultimate seats Installation Manual

0

Filed Under (Harley Davidson) by admin on 04-04-2012

download
1. Remove original seats from your bike. #2. Your new Ultimate seats install using the front seat side mount bolts and the passenger seat is bolted to the front seat and rear fender. Side mount hex nuts = 2. If your stock rider seat is a rear fender mount, install one of the hex nut inserts on each side of the frame if they are not in your bike frame already. #3. All the mounting brackets are already installed on your new seats. #4. Connect our passenger seat to the rider seat with the 2 new round head allen bolts ( 1/4″ x ¾”) #5. Use the 2 new supplied bolts to attach the rider seat to the bike frame, one on each side into the threaded inserts ( 1/4″ x ½”) pan Phillips head) #6. Use the other new bolt for the passenger seat rear bracket in the fender (1/4″ x ½”) pan head. Enjoy the ride again

Incoming search terms:

Incoming search terms: