2007 yamaha v star 650 headlight wiring diagram

You search Auto repair manual PDF 2007 yamaha v star 650 headlight wiring diagram, if there are search results will appear below. If search results do not exist, please search by others keyword.



  2007 yamaha v star 650 headlight wiring diagram Direct Download speed 5282 Kb/s

  2007 yamaha v star 650 headlight wiring diagram Full Version speed 6162 Kb/s



YAMAHA V-STAR 650/ 1100 CLASSIC F ATS/ SLIMS MOUNTING KIT INSTALLATION INSTRUCTIONS

0

Filed Under (Yamaha) by admin on 10-11-2010

download
1. Cover gas tank and front fender with towels to avoid damage during installation. 2. Install the two mounting plates onto the windshield, using the bottom and third bolt up. Leave the nylon washers off. The small tab goes to the bottom, big one at the top. (see Figure 1) Tabs face out away from the headlight when installed correctly. 3. Remove the headlight lens and chrome Turn Signal Bar cover and set them in a safe place. (see figure 2) 4. Remove the (3) socket head cap screws that hold the Headlight housing and let it rest carefully so that it does not fall. 5. Remove the turn signal bar by extracting the two socket head cap screws and let it dangle. (see figure 2) 6. Loosely install the throttle-side Bracket and Headlight using one of the (3) new longer 6mm x 30mm socket head cap screws. The nylon washer goes in between Headlight Housing and Headlight Bracket. (see figure 3) Install one of the (2) new 8mm x 45mm SS flat head screw and spacer in the lower hole to mount the turn signal bar. Insert the bolt in this order: bolt – windshield bracket – spacer – turn signal bar, and loosely tighten . (see Figure 3) Repeat these steps for the Clutch side. (See figure 4 for optional Cobra Light Bar installation, or to move Turn Signals forward to mount Lowers closer to the windshield.) 7. Once both windshield brackets are in place and all the new bolts are in place, Tighten all bolts. Re-install the chrome Turn Signal Bar cover. (Leave the chrome cover off if you use the alternate installation for Light Bar or Lowers). Re-Install the Headlight lens. 8. Loosen the (4) anchor bolts on the side of the windshield brackets. Slip the windshield mounting plates onto the brackets starting with the upper slot first then slip the bottom slot in. Adjust height, angle and tighten all bolts. This is a quick change kit. ALWAYS tighten all mounting bolts after removing or installing the windshield

Incoming search terms:

YAMAHA V-MAX PERIODIC MAINTENANCE AND MINOR REPAIR

0

Filed Under (Yamaha) by admin on 25-11-2010

download
PERIODIC MAINTENANCE AND MINOR REPAIR -. 1. Screw (x 2) EAU03003 Replacing the headlight bulb This motorcycle is equipped with a quartz bulb headlight. If the headlight bulb burns out, replace it as follows. 1. Remove the headlight unit by re- moving the screws. 2. Disconnect the headlight coupler, and then remove the headlight unit and bulb cover. 1. Headlight bulb holder 3. Remove the headlight bulb holder by turning it counterclockwise, and then remove the defective bulb. EWOOOl19 Headlight bulbs get very hot. Therefore, keep flammable products away from a lit headlight bulb, and do not touch the bulb until it has cooled down. 4. Place a new bulb into position, and then secure it with the bulb holder. 1. Do not touch this area. EC000105 Do not touch the glass part of the headlight bulb to keep it free from oil, otherwise the transparency of the glass, the luminosity of the bulb, and the bulb life will be adversely affected. Thoroughly clean off any dirt and fingerprints on the headlight bulb using a cloth moistened with alcohol or thinner. 5. Install the bulb cover, and then connect the coupler. 6. Install the headlight unit by install- ing the screws. 7. Have a Yamaha dealer adjust the headlight beam if necessary. 6-40 PERIODIC MAINTENANCE AND MINOR REPAIR 1. Screw (x 2) 1. Tail/brake light bulb (x 2) EAU00855 Replacing a turn signal light bulb or the tail/brake light bulb 3. Insert a new bulb into the socket, push it in, and then turn it clock- wise until it stops. 1. Remove the lens by removing the screws. 2. Remove the defective bulb by pushing it in and turning it counter- clockwise. 1. Turn signal light bulb 4. Install the lens by installing the screws. EC000108 Do not overtighten the screws, oth- erwise the lens may break

Incoming search terms:

YAMAHA V-Star 650 BIG AIR KIT REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Yamaha) by admin on 21-01-2012

download
Remove fuel tank and air filter assembly per Yamaha service manual procedures. 2. Remove the air silencer box under the tank. 3. Install supplied BA-2410-00 Needle/Jet kit according to the instructions in the jet kit package being sure to use the Jets and Needle Slot setting called out for the external BAK filter assemble. 4. Reinstall the air silencer box under the tank. 5. Remove the rubber boot from the stock air box. It is glued-in from the factory, but will come loose if gently persuaded. See photo #1 Our install guides provide a basic outline on the proper installation of our products. Further tuning and/or fitment may be required. Barons bears no responsibility on installation costs associated with this product. © 2010 Barons Custom Accessories 7401 Slater Ave. Huntington Beach, CA 92647 (714)274-4065 – Ph. (714)848-0718 – Faxwww.baronscustom.comtech@baronscustom.com Page: 2 BA-2011-00/03/06/07/13/13B BIG AIR KIT – YAMAHA V-Star 650 6. Install the stock rubber boot into your new Baron air filter backing plate with the supplied glue. Squeeze glue liberally into sealing groove in stock rubber boot. See photo #2 Allow glue to set up and dry prior to mounting onto bike

Incoming search terms:

V-Star 1100 And Dragstar 1100 Modification V-Star Driving/ Passing Lights Factory Chrome Light Bar Cover Installation

0

Filed Under (Yamaha) by admin on 08-11-2010

download
Modify your factory light bar cover to fit on Yamaha brand driving/passing lights. Use a rotary tool to widen the fastening area of the lower backside clips on the cover. The total width between the clips should be 4 æ inches. Trim off º inch on both inside ends of the lower backside attachment clips. Trim the clips equally. The following picture shows a modified cover. Narrow the clips on both ends to fit over the welds on the bar. The cover will not attach to the bar if the width between the clips is too narrow. If the width is too wide the cover may slide sideways on the bar. Narrow both clips equally to center the cover over the welds on the lower edge of the bar. The top of the cover is modified to allow the cover to fit over the bolts on the light bar. The top edge of the cover is filed æ inch deep and 5/8 inch wide to fit over the bolts. The back top edge is filed or ground 1/8 inch to fit over the light bar fastening bracket. Use care when filing chrome covered plastic. The following picture will help to complete this step in the modification. Modify your factory light bar cover to fit on Yamaha brand driving/passing lights. The ends of the cover are modified to allow the cover to fit over the upward curved light bar. The upper openings on the ends of the cover that fit over the bar must be filed to enlarge the area. Grinding the cover ends will allow the cover to fit and clip onto the bar. The end openings are filed or ground at an angle to match the slope of the bar. This picture shows the outer end of the cover. The ends of this cover have been modified by enlarging the area on the upper edges to fit over the upward curving light bar. The ends must be enlarged 1/8 inch on the top edge. The cover edge can be slanted upward to match the curved bar. Modify the cover ends until it fits without the outer chrome cover touching the bar. Modify your factory light bar cover to fit on Yamaha brand driving/passing lights. Sometimes the modified light bar cover may touch the bottom of the headlight. Modify the cover, or adjust the bar or headlight if you notice the headlight touching the bar cover. This modification makes the V-Star motorcycle with Yamaha driving lights look better. The light bar bolts are covered and the chrome cover improves the appearance of the front of your bike. Other V-Star riders will notice how nice the front of your bike looks with the chrome light bar cover installed

Incoming search terms:

YAMAHA V-STAR 650 CRUZER EXHAUST SYSTEM INSTALLATION MANUAL

0

Filed Under (Yamaha) by admin on 28-12-2010

download
STOCK EXHAUST SYSTEM REMOVAL 1. This Exhaust system is specifically designed for California models, before continuing be sure it is the correct system for your application. 2. Loosen clamp that connects muffler to front head pipe. 3. Remove cylinder exhaust bolts from rear head pipe that connects rear head pipe to cylinder (save for re- use). 4. Remove bolts that connect mufflers to mounting bracket. Remove complete system. Note: Assistance may be required. Page 1of 4 Y411IN Rev. 1.0 YAMAHA V-STAR 650 CRUZER EXHAUST SYSTEM, CA Model Part #31505 Tools required for installation: 1/2”, 12mm & 10mm wrenches 5mm, 6mm Allen wrenches 5/16″ nutdriver / flat blade screwdriver VANCE & HINES EXHAUST SYSTEM INSTALLATION 1. Check condition of stock exhaust gaskets. Replace if damaged or worn. 2. Install mounting bracket (stamped 370-P) in the original muffler mounting position, using two 8mm bolts (supplied)(Figure 1). 3. Mark outside surface of front and rear heat shields with location of mounting clips that are welded to the inside (Figure 2). Place each heat shield on a non abrasive surface such as a blanket or carpet. Lay each head pipe/muffler onto its respective heat shield (Figure 3). 4. Loosely install each hose clamp by feeding tail end of clamp into heat shield clip (Figure 4). Take note of clamp screw head direction (Figure 3). Screw head should be accessible when system is installed on motorcycle for adjustment purposes. Note: Do not tighten yet. 5. Install T-bolt clamp onto front muffler. Slide muffler onto front head pipe. Slide dog bone shaped nut plate (supplied) inside bracket welded to backside of front muffler. Attach muffler to mounting bracket 370-P using two 5/16″ flange bolts (supplied) engaging dog bone nut plate. Leave head pipe/muffler assembly loose at this time (Figure 4). 6. Using stock Allen bolts, carefully install rear head pipe/muffler assembly into exhaust port. (Assistance may be required). Note: Do not tighten yet. 7. Slide dog bone shaped nut plate (supplied) inside bracket welded to backside of rear muffler

Yamaha V-Star 650 Rear Lowering Kit REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Yamaha) by admin on 18-10-2010

download
INSTALLATION PROCEDURE 1. Secure motorcycle to a bike lift and raise the motorcycle. 2. Remove stock rear shock from the motorcycle per standard Yamaha shop manual instructions. 3. Place the shaft of the shock in V” blocks and secure this in a vice or press, applying firm pressure to the V” blocks to trap the shaft so it will not turn. Unscrew the upper shock mount eyelet from the shaft. NOTE: The upper mount is a standard thread so you will rotate the mount counter-clockwise to unscrew it. 4. Next, screw the New LA Choppers Shock Mount onto shock shaft using Loctite. 5. Re-install shock spring, making sure it is locked in place with the retaining ring prior to slowly releasing the spring compressor. Allow shock spring to expand against the retaining ring and machined washer. 6. Reinstall shock onto the motorcycle per standard Yamaha shop manual instructions. WARNING: Installing a lowering kit will decrease initial ground clearance. The motorcycle will be lower to the ground and care should be taken to avoid bottoming, especially over bumps or in turns. To maintain proper balanced geometry, the front and rear of the motorcycle should be lowered equally. Failure to properly install the lowering kit and operate the motorcycle after installation may result in serious injury or death to the rider. LIMITED GUARANTY: Because we cannot control the application of our products, buyer assumes risks for any and all damage caused to him or herself or any third party by virtue of any failure of these parts. Guaranty for such parts is limited to our replacement costs thereof. This guaranty is in lieu of all other guaranties or warranties express or implied, and all other such guaranties or warranties are hereby expressly disclaimed. By installation of these parts, buyer irrevocably agrees to the foregoing

Yamaha XVS650 and 1100 Drag Star/V-Star Service and Repair Manual

0

Filed Under (Yamaha) by admin on 27-04-2011

download
Fortunately, Haynes cruises to the rescue with the introduction of its new Service and Repair Manual for all Yamaha XVS650 and 1100 models – XVS650 (‘97-’05), XVS650A Classic (‘98-’05), XVS1100 (‘99–’05) and XVS1100A Classic (‘00–’05). Hailed as “… essential reading for any biker tackling his own servicing…” by Motor Cycle News, Haynes manuals have an enviable reputation. The new manual provides fully illustrated, step-by-step instructions for DIY servicing, overhaul and repairs of the engine and transmission, fuel and ignition systems, suspension and steering, the braking system and the electrical system. Each task is given a spanner rating for complexity and experience required. Checking and adjusting the valve clearances is rated as three spanners out of five. There are full-colour sections on the history of the models, on daily preride hecks and those all-important wiring diagrams, plus tools required and Haynes Hints. For instance, when changing the brake fluid how to tell when all the old fluid has been displaced The section guiding readers

Incoming search terms:

Honda Shadow A.C.E. v. Yamaha V-Star 1100 Middleweight Import Cruiser Shootout

0

Filed Under (Tips and Review) by admin on 25-11-2010

download
You want a big cruiser but you don’t need a large 1500 cc behemoth that weighs close to half-a-ton fully loaded. You want something you can cruise down the boulevard on but you want to be able to handle a corner or two. You want classic styling but you insist on reliability as well. If these are your guidelines, then Honda and Yamaha might have what you’re looking for in the guise of the Honda Shadow American Classic Edition and Yamaha V-Star 1100. Shadow ACE 1100 The ACE and V-Star have a few things in common: Both sport requisite V-twin powerplants (75° for the V-Star and 45° for the ACE) and both possess typical Japanese refinement. Aside from these similarities, the two rides are very different machines. While both machines are shaft driven, the ACE uses the shaft housing as the swingarm. Although this arrangement is effective, it’s a bit lacking style-wise. However, the whitewall tires and the classic fenders and tank help to create a traditional design that turns heads when you’re out and about. The V-Star uses a different approach, utilizing a pivoting sub-frame design with a hidden mono-shock that keeps the lines fluid and consistent with the rest of the bike. Although this beast isn’t equipped with whitewall tires, it still cuts a graceful, glittering profile. The only flaw we noticed was the small headlight that

Incoming search terms:

Ducati SPORT TOURING HEADLIGHT UPGRADE INSTALLATION AND REMOVAL INSTRUCTIONS

0

Filed Under (Ducati) by admin on 25-10-2010

download
1. Remove the following fairing components per the instructions in the Ducati owners manual: • Instrument surrounds • Headlight fairing • Chin fairing (under headlight/air intake) • Right-side middle fairing (covers battery) 2. Disconnect the speedometer cable from the speedometer. Unthread the ring nut at the top of the speedometer cable and retract the cable downward about 4-6 inches. 3. Disconnect the headlight wiring from the headlight bulbs. Retract the rubber boots at the rear of the headlight assembly to gain access to the wire terminals. Note that the two ¼ inch terminals at the high- beam bulb have locking clips that should be depressed before pulling the terminal away from the bulb. 4. Unplug the parking light from the headlight body by grasping the wires and carefully pulling it out. 5. Remove the two rubber plugs covering the lower headlight mounting screw access holes beneath the air intake horn. 6. Using an 8mm hex socket inserted through the lower access holes remove the two hex-head bolts securing the bottom of the headlight to the frame. 7. Using the same socket wrench, remove the two 8mm hex-head bolts securing the top of the headlight assembly to the frame. 8. Remove the headlight assembly from the frame. 9. Remove the two rubber grommets and steel reducing sleeves from the frame at the top mounting locations for the headlight. Leave the lower pair in place; these will be re-used, as shown in Figure 6

Incoming search terms:

ODYSSEY DRYCELL MOTORCYCLE BATTERY COMPATIBILITY

0

Filed Under (Triumph) by admin on 30-10-2010

download
BMW 1200 1200 1150 1100 1100 1000 1000 1000 1000 900 850 800 800 800 750 750 750 750 750 650 650 600 600 500 BUELL 1200 1200 1200 1000 DUCATI 860 750 500 HARLEY DAVIDSON 1570 1570 1450 1450 1340 1340 1340 1200 883 HONDA 1800 1500 1200 1100 1000 1000 900 750 750 650 650 650 600 400 200 150 150 125 K1200RS, LT R1200C R1150GS, R R1100GS/R R1100RS/T/S/LT “K” Models R100/7 100RS R100GS, R, RS, RT R90/6, R90S R850R R80GS, R80ST R80, R80RT R80/7/RT K75, RT K75C, S R75/5 R75/7 R75/6 R65 R65LS R60/5 R60/6, R60/7 R50/5 S1 Lightning X1, S3, S3T, M2 S2/T, RS1200, RR1200 RR1000 GT, GTS GT, Laguna Seca GTL, GTV, Sport FXST, FLST FXD FXD FXST, FLST FXD FXST, FLST FL/H/T/HT XL, XLH XLH, XLH GL1800, VTX1800C Gold Wing-All Gold Wing-All Gold Wing-GL1100 CBX1000, SS opt. Gold Wing-GL1000 CBR900R,RR CB750A (Hondamatic) VFR740R/ RVF750R NT650, SLR650, NX650 Vigor 650 XR650L VT600C, CD, CBR600 CBR400F CB-1 TR200 Fat Cat CH150 Elite FES150 FES125, Pantheon (97 -) (98 -) (00 -) (94-00) (90 -) (83-93) (76-84) (83) (87-95) (69-76) (95-97) (80-96) (84-95) (78-84) (85-95) (85-95) (70-73) (76-84) (69-76) (84-95) (78-84) (70-73) (69-84) (70-73) (96-99) (ALL) (ALL) (87) (2007) (2007) (99-06) (00-06) (97-99) (91-99) (80-96) (97-03) (97-02) (01-06) (88-00) (84-87) (80-83) (82) (75-79) (93-99) (76-78) (90/94) (88-91) (ALL) (93-06) (87-03) (89-90) (86) (87) (ALL) (ALL) #3561 #3561 #3561 #3561 #3561 #4989 #4989 #3561 #4989 #4989 #3561 #3561 #4989 #4989 #4989 #3561 #3561 #4989 #4989 #4989 #3561 #3561 #4989 #3561 #3591** #3591 #3591 #3591 #4989 #4989 #3561 #3591 #2528 #2528 #3591 #2528 #3591 #3560 #2528** #2528** #2528 #3560* #3560* #3560* #3560* #3560* #2519* #3560* #2519* #2519* #2519* #2519* #2519* #2519* #2519* #2519* #2519* #2519* PC680 PC680 PC680 PC680 PC680 PC925L PC925L PC680 PC925L PC925L PC680 PC680 PC925L PC925L PC925L PC680 PC680 PC925L PC925L PC925L PC680 PC680 PC925L PC680 PC545MJ PC545MJ PC545MJ PC545MJ PC925L PC925L PC680 PC545MJ PC545 PC545 PC545MJ PC545 PC545MJ PC680MJ PC545 PC545 PC545 PC680MJ PC680MJ PC680MJ PC680MJ PC680MJ PC310 PC680MJ PC310 PC310 PC310 PC310 PC310 PC310 PC310 PC310 PC310 PC310 cc model (year) cat. # mfg sku # KAWASAKI 1500 1500 1300 1000 1000 900 900 750 750 650 636 600 600 KTM 640 620 400 400 MOTO GUZZ I 1100 1100 1100 1000 1000 850 850 750 650 650 650 500 POLARIS All SUZUKI 1400 900 750 750 750 650 600 600 600 600 400 TRIUMPH 600 YAMAHA 1600 1300 1300 1200 1100 1100 1100 920 600 600 VN 1500-A Vulcan VN 1500-C Vulcan KZ 1300 Touring KZ 1000-P Police Z1000 ZX900-C, Ninja ZX900-E, F Ninja KZ750-L, Ninja Zx750 Ninja ZX, 7RR KLX650C, R ZX636-B Ninja ZX-6R ZX600-G, J Ninja ZX ZX600-K Ninja ZX Adventure, Duke, RXC Adventure, Duke, LC4 LC4 E/XC RXC LC4 Cali/Spc/Jackl/Stone/EV Quota/Sport 1100 VII EV/Bassa California III,Quota,Millie Convert,Daytona, LeMans LeMans T3, T4, T5 Nevada,NTX,Strada,V7,V75 NTX V65 V65 Florida V50 Victory GV 1400GC RF900, R, S, ZS GSX750F Katana GSX-R750 GSXR750W DR650SE GSF600S Bandit GSX600F Katana GSX-R600 RF600R, S GSF400 Bandit Daytona 600 XV 1600 Road Star 1300 Royal Star XVZ Venture Royale XVZ12T Venture XJ1100 Maxim XS 1100, L, S XV 1100, S/ Virago XV 920/R/M Virago XJ600S Seca II XT600E (87-98) (96-97) (79-82) (82-05) (03-04) (98-99) (00-04) (93) (91-97) (93-96) (03-04) (98-02) (03) (99-02) (96-98) (96-98) (96-01) (94-05) (97-02) (98-99) (ALL) (86-88) (94-97) (98-03) (96-99) (94-95) (96-04) (96-03) (98-04) (97-03) (94-96) (91-93) (03-04) (99-03) (96-03) (86-92) (83-85) (82) (78-92) (86-99) (81-83) (92-98) (90-95) #3560 #3560 #3560 #3560 #2519* #2519* #2519* #2519* #2519* #2519* #2519* #2519* #2519* #2519* #2519* #2519* #2519* #4989 #2528 #4989 #4989 #4989 #4989 #4989 #3561 #3561 #4989 #3561 #4989 #2519* #3560 #2519* #2519* #2519* #2519* #2519* #2519* #2519* #2519* #2519* #2519* #2519* #2528*** #2528*** #3560 #3560 #3560 #3560 #3560 #3560 #2519* #2519* PC680MJ PC680MJ PC680MJ PC680MJ PC310 PC310 PC310 PC310 PC310 PC310 PC310 PC310 PC310 PC310 PC310 PC310 PC310 PC925L PC545 PC925L PC925L PC925L PC925L PC925L PC680 PC680 PC925L PC680 PC925L PC310 PC680MJ PC310 PC310 PC310 PC310 PC310 PC310 PC310 PC310 PC310 PC310 PC310 PC545 PC545 PC680MJ PC680MJ PC680MJ PC680MJ PC680MJ PC680MJ PC310 PC310

Incoming search terms:

Incoming search terms: