2008 kymco 300 service manual

You search Auto repair manual PDF 2008 kymco 300 service manual, if there are search results will appear below. If search results do not exist, please search by others keyword.



  2008 kymco 300 service manual Direct Download speed 5282 Kb/s

  2008 kymco 300 service manual Full Version speed 6162 Kb/s



SUZUKI GSX-R1000 SERVICE MANUAL

0

Filed Under (Suzuki) by admin on 12-11-2010

download
Cover the throttle bodies to prevent anything from dropping into the engine. 1. Remove the front seat and disconnect the battery. (Refer to Service Manual, Page 8-8) 2. Lift up the fuel tank. (Refer to Service Manual, Page 5-3) 3. Remove the air cleaner box. (Refer to Service Manual, Page 5-14) 4. Remove and replace the ISC valve. (Refer to Service Manual, Page 5-25) NOTE: Since the ECM is also being replaced there is no need to perform the ISC valve preset operation. 5. Install the air cleaner box in reverse order of removal. (Refer to Service Manual, Page 5-14) 6. Lower the fuel tank. (Refer to Service Manual, Page 5-3) 7. Remove the upper seat rail plate. Disconnect and remove the ECM. (Figure 1) @ ISC Valve Mounting Screw Torque: 2.1± ±0.6 N.m (1.5± ±0.4 lb-ft) ! Carefully insert the ISC valve straight into the throttle body hole to prevent damaging the o-ring. Turn the ISC valve slightly to confirm that the o-ring has not twisted. Using the new screw provided in the replacement parts kit, make sure the screw is completely seated on the plate after the screw has been tightened to the specified torque. 4. Remove and replace the ISC valve. (Refer to Service Manual, Page 5-25) NOTE: Since the ECM is also being replaced there is no need to perform the ISC valve preset operation. ! Cover the throttle bodies to prevent anything from dropping into the engine. 1. Remove the front seat and disconnect the battery. (Refer to Service Manual, Page 8-8) 2. Lift up the fuel tank. (Refer to Service Manual, Page 5-3) 3. Remove the air cleaner box. (Refer to Service Manual, Page 5-14) REPLACEMENT PROCEDURE: 8. Install the new ECM in reverse order of removal. Apply thread lock to the upper plate mounting bolts when reinstalling the upper seat rail plate.

Incoming search terms:

HARLEY DAVIDSON BLADE FRONT WHEEL KITS INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 20-03-2011

download
INSTALLATION 1. Remove existing front wheel assembly. Save axle, axle nut, brake disc, and wheel spacers for kit installation. Refer to FRONT WHEEL in service manual. For FLSTC and FLSTN Models: Discard moon-style hub cap. or FXSTD: Discard tapered spacer. NOTE Install short valve stem (43157-83A) included in the installation kit. Discard all other valve stems. 2. See Figure 2. Install valve stem assembly (L) on wheel. Refer to TIRES in service manual. Do not re-use brake disc/rotor screws. Re-using these screws can result in torque loss and damage to brake components. (00319c) NOTES Install the primary bearing first using appropriate service manual and WHEEL BEARING REMOVER/INSTALLER. The side with the machined groove on the hub face is the primary bearing side for all kits except Kits 41681-07 and 40818-08. For Kit 41681-07: Install the wheel so that the hub markings are on the left side and the machined groove is on the right side of the motorcycle. • For 2006 and later FXDWG Models: When correctly installed, the tire will be 0.08-0.2 in (2-5 mm) off of center, compared to the fender. • For 2007 and later FX Softail and 2008 and later FXDWG Models: The left side of the wheel is the primary bearing side. • For 2006 and earlier FX Softail and 2007 and earlier FXDWG Models: The right side of the wheel is the primary bearing side. For Kit 40818-08: • Proper installation of this kit requires the separate purchase of two floating brake discs (44343-01 for 2004 – 2007 models and 44553-06A (stock) or 41500012 (polished) for 2008 and later models) and a tire (43371-07 on 2004-2008 models and 44026-09A on 2009-later models). The left side of the wheel has machined DOT markings to identify it as the primary bearing side. • For 2008 and later Touring: Install bearing shim (43903- 08) under the primary bearing. 3. Assemble wheel installation kit components and brake disc(s) to wheel, using the appropriate service parts table. Refer to FRONT WHEEL in service manual. 4. For FLSTC and FLSTN Models: Install wheel kit and right hand wheel spacer provided in installation kit. Refer to FRONT WHEEL in service manual. For FXSTD Models: Install wheel kit, stock wheel spacer and right side wheel spacer provided in installation kit in place of the tapered spacer discarded in Step 1. Refer to FRONT WHEEL in service manual. For FXSTS Models: Install wheel kit, stock wheel spacers and spacer provided in installation kit between the left side wheel spacer and the left fork. For all other models: Install previously removed wheel spacers. Refer to FRONT WHEEL in service manual. 5. Install front wheel (1), stock axle and stock axle nut. Refer to FRONT WHEEL in service manual. MAINTENANCE AND CLEANING Chrome parts must be maintained regularly to verify that they keep their original shine and luster. 1. Clean heavily-soiled wheel surfaces using Harley-Davidson Wheel and Tire Cleaner, applied with Harley Wheel and Spoke Brush. 2. Thoroughly clean chrome with a good quality chrome cleaner, such as Harley Bright Chrome Cleaner. 3. After cleaning and polishing, seal the finish with a good quality sealer, such as Harley Glaze Polish and Sealant

Incoming search terms:

HARLEY DAVIDSON FRONT THUNDERSTAR WHEELS INSTALLATION

0

Filed Under (Harley Davidson) by admin on 08-11-2010

download
Remove existing front wheel assembly. Save axle, axle nut, brake disc, and wheel spacers for kit installation. Refer to FRONT WHEEL in service manual. For FLSTC and FLSTN Models: Discard moon-style hub cap. -J04065 1 of 8 For FXSTD Models: Discard the tapered r ight side wheel spacer. Do not re-use brake disc/rotor screws. Re-using these screws can result in torque loss and damage to brake components. (00319c) NOTE • For Kits 43573-08, 43575-08, 43703-08, 43978-07, 43771- 07, 43609-07, 44323-07, 44282-07, 44322-07, 43975-07, 43602-07 and 43773-07 install short valve stem (43157- 83A) included in the installation kit. • For Kits 40943-09, 40966-09 and 40996-09 install long valve stem (43206-01) included in the installation kit. 2. See Figure 2. Install valve stem assembly (L, M or N) on wheel. Refer to TIRES in service manual. 3. Assemble wheel installation kit components and brake disc(s) to wheel, using the appropriate service parts table. Refer to FRONT WHEEL in Service Manual. NOTES Install the primary bearing first using appropriate service manual and WHEEL BEARING REMOVER/INSTALLER. For Kits 43573-08, 43575-08, 43703-08, 43978-07, 43771-07, 43609-07, 40943-09, 40966-09 and 40996-09: • The left side of the wheel has a machined groove (item 5, Figure 2) in the hub face and/or DOT markings to identify it as the brake disc and primary bearing side. • Install the wheel so that the valve stem is on the right side of the motorcycle. For Kits 44323-07, 44322-07 and 44282-07: • Install the wheel so that the hub markings are on the left side of the motorcycle. The left side of the wheel has a machined groove (item 5, Figure 2) in the hub face and hub markings to identify it as the primary bearing side. • These kits include one or two hub plates (43985-00) to install between the brake disc and the wheel and a chrome hub cap (43986-00) to install on the wheel opposite the brake disc side. Hub covers must be installed to prevent water intrusion, which could cause an imbalance condition. Dual brake disc models: Install one stainless steel hub plate (3) between each brake disc and wheel hub. Discard chrome hub cap (2). Install brake discs according to service manual procedures. Single brake disc models: Install one stainless steel hub plate (3) between the brake disc and wheel hub. Install the brake disc according to service manual procedures. Install the chrome hub cap (2) on the side opposite the brake disc. Discard extra stainless steel hub plate (3). • The gross axle weight ratings is unaffected by the installation of this wheel on a vehicle equipped with a 21-inch wheel. For Kits 43975-07, 43773-07, and 43602-07: • The wheel has a machined groove (item 5, Figure 2) in the hub face to identify the right side. • For 2007 and later FX Softail Models and 2008 and later FXDWG: The left side of the wheel is the primary bearing side. For all other models the right side of the wheel is the primary bearing side. • For Kit 43602-07: An arrow is engraved into the right side hub to indicate the direction of rotation. • For Kits 43975-07 and 43773-07: An arrow is cast between the spokes on the right side to indicate the direction of rotation. • These kits include one or two hub plates (43985-00) to install between the brake disc and the wheel and a chrome hub cap (43986-00) to install on the wheel opposite the brake-disc side. Hub covers must be installed to prevent water intrusion, which could cause an imbalance condition. Dual brake disc models: Install one stainless steel hub plate (3) between each brake disc and wheel hub. Discard chrome hub cap (2). Install brake discs according to service manual procedures. Single brake disc models: Install one stainless steel hub plate (3) between the brake disc and wheel hub. Install the brake disc according to service manual procedures. Install the chrome hub cap (2) on the side opposite the brake disc. Discard extra stainless steel hub plate (3). 4. Install wheel assembly parts from the appropriate Service Parts table for this fitment and stock brake disc. Discard parts from the installation kit that are not required. Refer to FRONT WHEEL in Service Manual. 5. For FLSTC and FLSTN Models: Install wheel kit and right side wheel spacer provided in installation kit. For FXSTD Models: Install wheel kit, stock left wheel spacer and right side wheel spacer from installation kit in place of the tapered right side wheel spacer discarded in Step 1. Refer to FRONT WHEEL in service manual. For FXSTS Models: Install the left side wheel spacer provided in the kit between the stock left wheel spacer and the left fork. All other models: Install wheel spacers previously removed. 6. Install front wheel (1), stock axle and stock axle nut. Refer to FRONT WHEEL in service manual

Incoming search terms:

HARLEY DAVIDSON SCREAMIN' EAGLE TWIN CAM 110 (1800 CC) CONVERSION KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 19-02-2011

download
REMOVAL Prepare for Service 1. Position motorcycle on a suitable lift. NOTE If vehicle is equipped with Harley-Davidson Smart Security System, see owner’s manual for instructions to disarm the system. To prevent accidental vehicle start-up, which could cause death or serious injury, disconnect negative (-) battery cable before proceeding. (00048a) 2. Disconnect battery cables, negative (-) battery cable first. 3. Remove seat according to the instructions in the service manual. 4. Refer to service manual to remove left saddlebag and side cover. When servicing the fuel system, do not smoke or allow open flame or sparks in the vicinity. Gasoline is extremely flammable and highly explosive, which could result in death or serious injury. (00330a) 5. Remove fuel tank according to the instructions in the service manual. Remove Engine Components 1. Remove existing air cleaner assembly. Discard backplate but save remaining parts. Refer to AIR CLEANER REMOVAL in service manual. 2. Remove existing exhaust system. Refer to EXHAUST SYSTEM REMOVAL in service manual. 3. Remove engine from chassis following the instructions in the service manual. 4. Disassemble engine top end and bottom end. Refer to appropriate ENGINE sections in service manual. 5. Remove existing clutch diaphragm spring. Refer to CLUTCH REMOVAL in service manual. The procedures in this instruction sheet should be performed by one experienced in precision measuring techniques. Failure to meet tolerances called for in this instruction sheet can result in engine damage. (00511b) -J04793 1 2 is03517 1. O-ring counterbore 2. Spigot bore Figure 1. Spigot Bore and O-Ring Counterbore Dimensions Table 1. Spigot Bore and O-Ring Counterbore Dimensions Depth Bore Description 1.625 +/- 0.010 in. (41.3 +/- 0.25 mm) 4.205 +/- 0.010 in. (107 +/- 0.25 mm) Spigot Bore 0.085 +/- 0.003 in. (2.16 +/- 0.08 mm) 4.415 +/- 0.002 in. (112 +/- 0.05 mm) O-Ring Counter- bore is03456 Figure 2. Cylinder Wall MACHINE CRANKCASE Crankcase Boring Preparation NOTE During final assembly of the engine, Harley-Davidson recommends replacing the OE cylinder studs with Screamin’ Eagle High Tensile Studs (16505-01). 1. Remove cylinder studs from the engine crankcase. 2. Mask off all bearings and oil holes to prevent debris and contaminants from entering those areas. 3. Inspect and clean engine case mating surfaces. 4. See Figure 6. Reassemble engine case with OE screws, except the top center screw between the cylinders, and tighten to specifications listed in service manual. NOTE To prevent damage to crankcase boring tool, it is important to replace the top center screw with a modified top center screw (1093). This screw is included in the Crankcase Boring Tool Kit (94419-06) and can be purchased separately from a Harley- Davidson dealer. 5. Install modified top center screw (1093) between the cylinders and tighten to 50-90 in-lbs (5.6-10.2 Nm). 6. See Figure 1 and Table 1. Machine crankcase cylinder spigot bore and O-ring counterbore to the dimensions shown. Modify Crankcase

Incoming search terms:

HARLEY DAVIDSON VRSC CHROME WHEEL KITS INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 18-03-2011

download
Installation To prevent accidental vehicle start-up, which could cause death or serious injury, remove maxi-fuse before proceeding. (00251a) 1 WARNING 1 WARNING ® Kit Numbers 41279-04, 41282-04, 41463-05, 41467-05, 41633-05, 41634-05, 41640-05, and 41639-05 1 of 3 Figure 1. Rear Wheel Removal i02495 1. Axle (keep) 2. Axle adjuster (keep) 3. Axle nut (keep) 4. “E”-clip (keep) 5. Spacer (3) (keep) 6. Torx screw (5) (replace) 7. Brake disc (keep) 8. Wheel assembly (replace) 9. Valve cap (keep) 10. Compensator bowl (keep) 11. Compensator cushion (keep) 12.12 pt screw (5) (keep) 13. Lockwasher (5) (keep) 14. Sprocket assembly (keep) 1. Refer to the Service Manual and follow the MAXI-FUSE instructions to remove the right-side cover and maxi- fuse. Proceed to Step 2 for the wheel being replaced. Rear Wheel 2. See Figure 1. Remove the rear wheel per the REAR WHEEL, REMOVAL instructions in the Service Manual. 3. Disassemble, clean and inspect all parts to be re-used per Service Manual instructions. 4. Re-assemble all saved components to the new chrome rear wheel assembly. See REAR WHEEL, ASSEMBLY in the Service Manual. Do not re-use brake disc screws. Re-using disc screws can result in torque loss and damage to rotor and/or brake assembly. (00319b) 5. Fasten the brake disc to the valve stem side of the wheel using the Torx®screws from the kit. Install the compensator bowl with the 12-point screws and lockwashers saved earlier. 6. Install the new wheel to the rear fork. Refer to REAR WHEEL, INSTALLATION in the Service Manual. Proceed to Step 7. Front Wheel 2. See Figure 2. Remove the front wheel per the FRONT WHEEL, REMOVAL instructions in the Service Manual. 3. Disassemble, clean and inspect all parts to be re-used per Service Manual instructions. Mark the left and right brake discs so they can be re-installed to the same location. 4. Re-assemble all saved components to the new chrome front wheel assembly. See FRONT WHEEL, ASSEMBLY in the Service Manual. Do not re-use brake disc screws. Re-using disc screws can result in torque loss and damage to rotor and/or brake assembly. (00319b) 5. Using the Torx ® shoulder bolts from the kit, and the saved spring washers fasten the brake discs to the same side of the wheel from which they were removed. 6. Install the new wheel to the front forks per the FRONT WHEEL, INSTALLATION instructions in the Service Manual. Proceed to Step 7. Front and Rear Wheels 7. Refer to the Service Manual and follow the MAXI-FUSE instructions to replace the maxi-fuse and right-side cover. After servicing brakes and before moving motorcycle, pump brakes to build brake system pressure. Insufficient pressure can adversely affect brake performance, which could result in death or serious injury. (00279a) After servicing the brake system, test brakes at low speed. If brakes are not operating properly, testing at high speeds can cause loss of control, which could result in death or serious injury. (00289a) Maintenance and Cleaning Chrome parts must be maintained regularly to ensure that they keep their original shine and luster. 1. Clean heavily-soiled wheel surfaces using Harley Wheel and Tire Cleaner, part number 94658-98, applied with Harley Wheel and Spoke Brush, part number 43078-99. 2. Thoroughly clean chrome with a good quality chrome cleaner, such as Harley Bright Chrome Cleaner, part number 94683-99. 3. After cleaning and polishing, seal the finish with a good quality sealer such as Harley Glaze Polish and Sealant, part number 99701-84

Incoming search terms:

HARLEY DAVIDSON SOFTAIL 6 SPEED TRANSMISSION – COMPLETE INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 13-04-2011

download
Removal of Original Transmission 1. Position motorcycle on a suitable lift. To prevent accidental vehicle start-up, which could cause death or serious injury, disconnect battery cables (negative (-) cable first) before proceeding. (00307a) Disconnect negative (-) battery cable first. If positive (+) cable should contact ground with negative (-) cable connected, the resulting sparks can cause a battery explosion, which could result in death or serious injury. (00049a) 2. Refer to the Service Manual and follow the instructions given to remove the seat and disconnect the battery cables, negative cable first. 3. Refer to the TRANSMISSION CASE REMOVAL in the Service Manual and follow the instructions given to remove the components with the following steps. 4. Refer to PRIMARY CHAINCASE COVER REMOVAL in the Service Manual and follow the instructions given to remove the primary chaincase cover. Wear safety glasses or goggles when removing or installing retaining rings. Retaining rings can slip from the pliers and could be propelled with enough force to cause serious eye injury. (00312a) 5. See the PRIMARY CHAIN and COMPENSATING SPROCKET REMOVAL in the Service Manual and use the instructions given to remove the primary drive assem- bly. 6. Refer to the STARTER REMOVAL in the Service Manual and remove the the starter. 7. See the VEHICLE SPEED SENSOR section and unplug the vehicle speedometer sensor connection and remove the mounting bolt. Lift sensor from the transmission case and set aside for later re-installation. 8. Refer to NEUTRAL SWITCH and disconnect the connectors from the neutral switch. 9. Refer to PRIMARY CHAINCASE in the Service Manual and follow the instructions given to remove the primary chaincase housing. 10. Refer to EXHAUST SYSTEM in the Service Manual and remove the exhaust. 11. See the REAR WHEEL REMOVAL and loosen but, do not remove rear axle to relieve drive belt tension and remove the belt from the sprocket from the transmission. 12. Refer to OIL TANK REMOVAL in the Service Manual and follow the instructions given to drain, remove the oil tank and detach the vent, feed and return lines. 13. Refer to CLUTCH CONTROL in the Service Manual and follow the instructions given to remove the clutch cover and disconnect the clutch cable end from the cover. Set the cable aside for later re-installation

Incoming search terms:

HARLEY DAVIDSON DYNA STATOR AND ROTOR KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 30-03-2011

download
REMOVAL To prevent accidental vehicle start-up, which could cause death or serious injury, disconnect negative (-) battery cable before proceeding. (00048a) 1. Disconnect negative battery cable. See BATTERY MAINTENANCE in Service Manual. 2. Remove primary cover, primary drive, and clutch. See DRIVE COMPONENTS in Service Manual. 3. Remove primary chaincase according to the instructions in the Service Manual. 4. See Figure 2. Pull off the alternator rotor (1) using two bolts inserted through the holes in the rotor face. 5. Remove the two T-27 TORX screws (2). 6. Unplug the voltage regulator and remove the stator (3). See VOLTAGE REGULATOR in Service Manual. 7. Disassemble connector [46B] (A). See DEUTSCH ELECTRICAL CONNECTORS in Service Manual. NOTE Contact cleaner, alcohol, or glass cleaner sprayed on rubber grommet (B) will provide lubrication when pulling it through crankcase hole. 8. Move grommet (3) to one side and spray contact cleaner into gap. Repeat for other side. Pull rubber grommet (B) through crankcase hole. 9. Pull wires through crankcase hole. INSTALLATION 1. Insert wires through crankcase hole. 2. See Figure 1. Push rubber grommet (B) through crankcase hole. If necessary, apply the same lubricant used during removal. 3. Insert wires into connector [46B] (A). 4. Mate connector [46]. See VOLTAGE REGULATOR in Service Manual. is03776 Figure 1. Voltage Regulator 5. See Figure 2. Install the stator (3) on the crankcase and fasten in place using new TORX screws (2). Tighten to 55-75 in-lbs (6.2-8.4 Nm). 6. Install the rotor (1) on the sprocket shaft. 7. Apply Loctite Threadlocker 262 (red) to sprocket nut threads. Tighten sprocket nut to 150-165 ft-lbs (203.4- 223.7 Nm). 8. Install primary chaincase according to the instructions in the Service Manual. 9. Install clutch, primary drive, and primary cover. See DRIVE COMPONENTS in Service Manual. 10. Connect negative battery cable. See BATTERY MAINTENANCE in Service Manual

HARLEY DAVIDSON CHROME 1.00 INCH (25.4 MM) DIAMETER HANDLEBAR KITS REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 11-03-2011

download
REMOVAL To prevent accidental vehicle start-up, which could cause death or serious injury, remove main fuse before proceeding. (00251b) 1. Refer to the service manual and follow the instructions given to remove the main fuse. 2. Remove the outer fairing. See the service manual. 3. Remove the fairing cap. See the service manual. 4. FLHX Models: Handlebar-mounted mirrors (purchased separately) are required for proper installation of this handlebar. Removal of the inner fairing may be required, refer to the service manual. If fairing-mounted mirrors are being removed: Install the two small black plugs and large black plugs (purchased separately) to plug the fairing mirror holes. Direct contact of D.O.T. 4 brake fluid with eyes can cause irritation. Avoid eye contact. In case of eye contact flush with large amounts of water and get medical attention. Swallowing large amounts of D.O.T. 4 brake fluid can cause digestive discomfort. If swallowed, obtain medical attention. Use in well ventilated area. KEEP OUT OF REACH OF CHILDREN. (00240a) D.O.T. 4 brake fluid will dama ge painted and bod y panel surfaces it comes in contact with. Always use caution and protect surfaces from spills whenever brake work is performed. Failure to comply can result in cosmetic damage. (00239b) NOTE Immediately wipe up any brake fluid spillage with a clean, dry, soft cloth. Follow up by thoroughly wiping affected area with a clean, damp, soft cloth (small spills) or washing with a large quantity of soapy water (large spills). Cover nearby motorcycle surfaces with a polyethylene protective sheet to help protect against damage to finish caused by spillage or splashes of DOT 4 brake fluid. 5. Drain the brake fluid from the front brake reservoir and lines per the instructions in the service manual. NOTE Cover the front fender and the fuel tank with clean shop towels to prevent scratching. 6. Models with Radio: Remove the radio. See the service manual. Models without Radio: Remove the storage box. See the service manual. a. The four socket head screws fastening the radio or storage box to the left and right radio support brackets can be accessed through the oblong holes in the fairing brackets. Use a long shank ball-end socket to remove the screws. b. Pull the radio or storage box forward to remove it from the opening in the inner fairing. Remove brake line components carefully. Damage to seating surfaces can cause leakage. (00320a) 7. Remove and retain the button head screw on the underside of the fork stem and bracket assembly that holds the brake line manifold tee. 8. Note the front brake line routing and the orientation of the banjo fittings. Disconnect the brake line from the front brake calipers and the front brake master cylinder assembly. Save the banjo bolts, but discard the two gaskets found at each banjo fitting. See the service manual. 9. Remove the front brake line assembly. NOTES Refer to the parts catalog for this year and model for a replacement OE brake line assembly and clutch cable, if needed. Ask a Harley-Davidson dealer about the selection of Genuine Motor Accessory Custom Braided Clutch Cables and Brake Lines that are available. 10. Remove the front brake master cylinder and clutch lever assemblies from the handlebar. 11. Disconnect the clutch cable from the clutch lever. See the service manual.

Incoming search terms:

KYMCO MAXXER 300/ 250 MONGOOSE 300/ 250 SERVICE MANUAL

0

Filed Under (Kymco) by admin on 26-10-2010

download
apply or add designated greases and lubricants to the specified lubrication points. ÑAfter reassembly, check all parts for proper tightening and operation. ÑWhen two persons work together, pay attention to the mutual working safety. ÑDisconnect the battery negative (-) terminal before operation. ÑWhen using a spanner or other tools, make sure not to damage the motorcycle surface. ÑAfter operation, check all connecting points, fasteners, and lines for proper connection and installation. ÑWhen connecting the battery, the positive (+) terminal must be connected first. ÑAfter connection, apply grease to the battery terminals. ÑTerminal caps shall be installed securely. 1 . GENERAL INFORMATION 1-6 ATV 300/250 ÑIf the fuse is burned out, find the cause and repair it. Replace it with a new one according to the specified capacity. ÑAfter operation, terminal caps shall be installed securely. ÑWhen taking out the connector, the lock on the connector shall be released before operation. ÑHold the connector body when connecting or disconnecting it. ÑDo not pull the connector wire. ÑCheck if any connector terminal is bending, protruding or loose. Confirm Capacity 1 . GENERAL INFORMATION 1-7 ATV 300/250 ÑThe connector shall be inserted completely. ÑIf the double connector has a lock, lock it at the correct position. ÑCheck if there is any loose wire

Incoming search terms:

KTM 125 EXC, EXC SIXDAYS 200 XC, XC-W, EXC 250 XC, XC-W, EXC, EXCSIXDAYS 300 XC, XC-W, EXC-E, EXC-ESIXDAYS OWNER'S MANUAL 2008

0

Filed Under (KTM) by admin on 02-12-2010

download
Chassis number The chassis number is stamped on the right side of the steering head tube. Enter this number in the field on page no 1. Engine number, engine type The engine number and the engine type are stamped into the left side of the engine below the engine sprocket. Enter this number on page 1. Clutch lever The clutch lever [1] is located on the left side of the handlebars. The adjusting screw [A] is used to change the original position of the clutch lever (see maintenance work on chassis and engine). The clutch is hydraulically actuated and adjusts itself automatically. Hand brake lever The hand brake lever [2] is mounted on the handlebars on the right and actuates the front wheel brake. The adjusting screw [B] can be used to change the basic position of the hand brake lever (see maintenance work on chassis and engine). OPERATION INSTRUMENTS » 1 2 A B
ENGLISH 6 OPERATION INSTRUMENTS » TEST All of the display segments briefly light up for the display function test. WS (wheel size) The display changes and the circumference of the front wheel is briefly displayed in millimeters (2205 mm corresponds to a front wheel circumference of 21″ with production tires). Afterwards the display will return to the previous display mode. Electronic speedometer The display in the electronic speedometer is activated as soon as you press a button on the speedometer or an impulse is received from the wheel sensor. The display lights up when the engine is running. The display is cleared if no button is pressed for 1 minute or no impulse is received from the wheel sensor. The button is used to change between display modes. The + and – buttons are used to control various functions. SPEED display mode / H (service hours) Only the SPEED / H and SPEED / ODO display modes are activated in the condition at delivery. SPEED/H is displayed whenever the display is activated and the front wheel is not turning. It automatically changes to the SPEED/ODO display mode as soon as the front wheel starts turning. SPEED displays the speed. H displays the engine’s service hours. The service hour counter starts to count as soon as you start the engine. The displayed figure cannot be changed. Service intervals are indicated in service hours for some KTM offroad motorcycles, making the service hour counter a very practical function. SPEED / ODO display mode (odometer) The SPEED/ODO mode displays the speed and the total distance traveled. The display automatically changes to the SPEED/H display mode when the front wheel stops turning. + button no function – button no function briefly press buttonchanges to the next display mode hold button 3 secs. changes to the next display mode The electronic speedometer has a number of display modes (functions) that you can also activate (reveal) (see: Activating and deactivating display modes).
ENGLISH 7 OPERATION INSTRUMENTS » SPEED / LAP (lap time) display mode You can use the manual stop watch to stop and store up to 10 lap times, which you can view in the LAP/LAP display mode (see below). LAP displays the lap times in hours, minutes and seconds. + button Starts and stops the stop watch, lap time is not reset to 0 – button Stops the stop watch, stores the lap time and restarts the stop watch again. The time is reset to 0. A total of 10 lap times can be stored. If the lap time continues to run after you press the – button, all 10 memory locations are occupied.To clear all of the stored lap times, hold the button for 3 seconds in the SPEED/LAP mode.Up to 10 lap times can be stored in this way. briefly press buttonChanges to the next display mode.If no lap time is stored or the motorcycle is driving, the LAP/LAP mode will be skipped. hold button 3 secs. Clears all LAP figures SPEED / CLK (time) display mode CLK displays the time in hours, minutes and seconds. + button no function – button no function briefly press buttonchanges to the next display mode hold button 3 secs. set the clock menu To set the clock, see „Setting the clock”. Activating and deactivating display modes In the display mode SPEED/H, press and hold the button for 3 seconds to access the SETUP menu. The active functions will be displayed. The blinking function can be activated by pressing the + button and deactivated by pressing the – button. Press and hold the button 3 seconds to store the settings. If no button is pressed for 20 seconds, the setting will be stored automatically and the display will return to the SPEED/H mode. + button activates the blinking display – button deactivates the blinking display briefly press buttonchanges to the next display without changing any settings hold button 3 secs. starts the SETUP stores the settings and changes to the SPEED/H mode

Incoming search terms:

Incoming search terms: