2008 road king fuel pump hose clamps

You search Auto repair manual PDF 2008 road king fuel pump hose clamps, if there are search results will appear below. If search results do not exist, please search by others keyword.



  2008 road king fuel pump hose clamps Direct Download speed 5282 Kb/s

  2008 road king fuel pump hose clamps Full Version speed 6162 Kb/s



YAMAHA Road Star Fuel Pump Relocation Kit INSTALLATION MANUAL

0

Filed Under (Yamaha) by admin on 08-11-2010

download
1. Remove seat and disconnect battery. Remove fuel tank along with both left and right side battery covers, and remove air box from carburetor (all per Yamaha standard shop manual procedures). 2. Remove chrome plastic cover over fuel pump and disconnect choke cable/knob from lower pump bracket. Remove pump-to-carb fuel line from fuel pump. Disconnect fuel pumps electrical lead connector. 3. Remove two (2) hex-head pump mounting bracket bolts and remove pump assembly from motorcycle. Slide fuel pump up and off bracket mounting posts (Caution: excess fuel may drain from pump and/or fuel lines and fuel filter!). Remove heat shield. Remove remaining fuel line from pump. Pull all fuel lines from filter and remove steel springs and hose clamps from these lines (these will be reused on the kits fuel lines). With a sharp knife or box cutter, trim off the top portion of the fuel pumps rubber isolation/mount system per Photo A. Next cut pumps wiring harness approximately half way between connector and pump. Strip the insulation from the ends of these wires as well as from the supplied Baron harness extension wires. Using the supplied electrical butt connectors, crimp Baron harness extensions red wire to pumps black-w/blue-strip wire, and Baron harness extensions black wire to pumps black wire. Repeat this process on other side of wire harness extension with pumps connector. Now, referring to Photo B, you will need to cut off the square tube that runs along the side of the fuel pump with a hack saw. Cut down toward pump body in a straight cut, then cut tube off by cutting along the body. This will allow you to twist pump in the rubber mount so the curved spigot is facing up (clockwise approx 1/4 turn). 4. Remove pump-to-carb fuel line from carb and separate electrical wires from this line. Remove this fuel line from engine. Re-route choke cable to right side of engine (toward carb) and rotate it up and over rear cylinder head back toward left side of bike. Mount new Baron choke bracket to the choke cable and tighten plastic nut. New choke bracket will mount to rear fuel tank mounting location (Photo C). 5. 99~03 models – Remove electrical relay bracket (found under the right side cover) from the bike and slide each relay off of this bracket. Install fuel pump onto new Baron Fuel Pump Bracket and install bracket in the same location as the stock bracket you just removed, using stock mounting hardware. Refer to Photo F for proper installation. 6. 04~07 models Remove electrical relays from stock bracket and remove relays from rubber holder. Cut rubber holder per Photo E and replace one of the relays into the rubber and install on to new Baron bracket. The second relay will be placed to the right of the tool bag under the seat and secured with the provided two-sided tape pad. Reconnect plugs to the relays. (Photo F)

Incoming search terms:

2007 Softail HARLEY DAVIDSON FUEL PUMP/ FUEL GAUGE SENDING UNIT REMOVAL AND INSTALLATION

0

Filed Under (Harley Davidson) by admin on 30-03-2012

download
1. Remove seat. 1 WARNING 1 WARNING To prevent spray of fuel, purge system of high-pressure fuel before supply line is disconnected. Gasoline is extremely flammable and highly explosive, which could result in death or serious injury. (00275a) 2. Purge the fuel supply line of high pressure gasoline. a. See Figure 4-36. Disconnect the fuel pump fuse from the main wiring harness. b. Start the engine and allow the vehicle to run. c. When the engine stalls, operate the starter for 3 seconds to remove any remaining fuel from the fuel lines. 1 WARNING 1 WARNING To prevent accidental vehicle start-up, which could cause death or serious injury, disconnect negative (-) battery cable before proceeding. (00048a) 3. Disconnect negative battery cable. 4. Remove instrument console. a. All but FXSTD, see Figure 4-37. Remove acorn nut and washer on instrument console to separate console from fuel tank. b. For FXSTD, see 8.26 INSTRUMENT CONSOLE: FXSTD. 5. Disconnect console wiring. Figure 4-36. Fuel Pump Fuse: View From Top Figure 4-37. Acorn Nut And Washer: All But FXSTD s0660x8xx 7526
4-28 2007 Softail: Fuel System HOME 1 WARNING 1 WARNING Gasoline can drain from the crossover line when disconnected from fuel tank. Gasoline is extremely flammable and highly explosive, which could result in death or serious injury. Wipe up spilled fuel immediately and dispose of rags in a suitable manner. (00259a) 6. Drain fuel tank. a. Obtain a short section of hose (5/16 inch I.D.). Insert bolt in one end of hose and install hose clamp to ensure that end is securely plugged. b. See Figure 4-38. Cut clamp (1) from one end of crossover hose (2). Quickly replace crossover hose on fuel tank fitting with open end of short hose while directing flow of gasoline from free end of crossover hose into suitable container. 7. See Figure 4-39. Unplug fuel pump module connector (3) [86]. 8. Remove top plate screws (2) and discard. 9. See Figure 4-40. Pull top plate (2) out of fuel tank enough to expose fuel hose and clamp (1). CAUTION Carefully inspect end of hose for cuts, tears, holes or other damage. Replace hose if any damage is found. Even the smallest hole can cause a reduction in fuel pressure. 10. Cut clamp and remove hose from regulator housing fit- ting.

Incoming search terms:

2003 SUZUKI SV 650 FUEL SYSTEM AND THROTTLE BODY SERVICE MANUAL

0

Filed Under (Suzuki) by admin on 26-02-2011

download
FUEL PUMP The electric fuel pump is mounted at the bottom of the fuel tank, which consists of the armature, magnet, impeller, brush, check valve and relief valve . The ECM controls its ON/OFF operation as controlled under the FUEL PUMP CONTROL SYSTEM . When electrical energy is supplied to the fuel pump, the motor in the pump runs and together with the impel- ler . This causes a pressure difference to occur on both sides of the impeller as there are many grooves around it . Then the fuel is drawn through the inlet port, and with its pressure increased, it is discharged through the outlet port . The fuel pump has a check valve to keep some pressure in the fuel feed hose even when the fuel pump is stopped . Also, the relief valve is equipped in the fuel pump, which releases pressurized fuel to the fuel tank when the outlet of the fuel pressure has increased up to 450 -600 kPa (4.5- 6.0 kgf/cm2,64- 85 psi) . Relief valve Brush , ∎ I,’ Check valve Magnet L Armature When the impeller is driven by the motor, pressure differential occurs between the front part and the rear part of the blade groove as viewed in angular direction due to fluid friction . This process continuously takes place causing fuel pressure to be built up . The pressurized fuel is then let out from the pump chamber and discharged through the motor section and the check valve . FUEL SYSTEM AND THROTTLE BODY 5- 3 Inlet port I I Impeller 5-4 FUEL SYSTEM AND THROTTLE BODY FUEL PRESSURE REGULATOR The fuel pressure regulator consists of the spring and valve . It keeps absolute fuel pressure of 300 kPa (3.0 kgf/cm2,43 psi) to be applied to the injector at all times . When the fuel pressure rises more than 300 kPa (3 .0 kgf/cm2, 43 psi), the fuel pushes the valve in the regulator open and excess fuel returns to the fuel tank . 90 Spring 02 Valve FUEL INJECTOR The fuel injector consists of the solenoid coil, plunger, needle valve and filter . It is an electromagnetic type injection nozzle which injects fuel in the throttle body according to the signal from the ECM. When the solenoid coil of the injector is energized by the ECM, it becomes an electromagnet and attracts the plunger. At the same time, the needle valve incorporated with the plunger opens and the injector which is under the fuel pressure injects fuel in conic dispersion . As the lift stroke of the needle valve of the injector is set constant, the volume of the fuel injected at one time is determined by the length of time during which the solenoid coil is energized (injection time)

Incoming search terms:

BUELL ACCESSORY GAS CAP KIT INSTALLATION MANUAL

0

Filed Under (Buell) by admin on 29-03-2011

download
Installation NOTE When performing the following Steps, use the Fuel Tank Vent Valve Installation Kit (Part Number 91432-96Y). This kit consists of: * Fuel Tank Vent Valve Installation Aid * Fuel Tank Vent Valve Fitting Socket To protect against shock and accidental start-up of vehicle, disconnect the battery cables, negative cable first, before proceeding. Inadequate safety precautions could result in death or serious injury. Always disconnect the negative battery cable first. If the positive battery cable should contact ground with the negative cable installed, the resulting sparks may cause a battery explosion which could result in death or serious injury. 1. Disconnect battery cables, negative cable first. An open flame or spark may cause a fuel tank explosion if all traces of fuel are not purged from the tank. Use extreme caution when servicing fuel tanks. Gasoline is extremely flammable and highly explosive. Do not smoke or allow open flame or sparks anywhere in the area when working on fuel system components. Inadequate safety precautions could result in death or serious injury. 2. Remove gas cap. 3. Carbureted Models: Drain fuel tank. Disconnect hose clamp and fuel supply hose from fuel supply valve and drain fuel into suitable, clean container. See applicable Service Manual, Section 4 for complete, detailed procedure. Fuel Injected Models: Relieve pressure from fuel system. See applicable Service Manual, Section 4 for complete, detailed procedure. Drain fuel tank. a. Using suitable external fuel pump, such as a Gas Caddy, pump fuel from tank and into a suitable, clean container. b. See instructions for external fuel pump for correct use. 4. See Figure 1. Cut cable tie securing vent hose to fitting and remove vent hose from fuel tank. Even with the fuel tank completely drained, a small amount of gasoline may leak from the bore when the fuel supply valve is loosened or removed. Thoroughly wipe up any fuel immediately and dispose of rags in a suitable manner. Gasoline is extremely flammable and highly explosive. Inadequate safety precautions could result in death or serious injury. 5. If the fuel supply valve requires cleaning or repair, refer to applicable Service Manual, Section 4, for complete, detailed procedures. 6. See Figure 1. Remove the fuel filler cap and O-ring. 7. Remove the eight self-tapping screws from fuel clamp flange and remove fuel cap flange

HARLEY DAVIDSON FUEL LEVEL SENDER ADAPTER BRACKET KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 28-02-2011

download
INSTALLATION To prevent accidental vehicle start-up, which could cause death or serious injury, remove main fuse before proceeding. (00251b) 1. Refer to the Service Manual and follow the instructions given to remove the main fuse. When servicing the fuel system, do not smoke or allow open flame or sparks in the vicinity. Gasoline is extremely flammable and highly explosive, which could result in death or serious injury. (00330a) 2. Remove the currently installed fuel tank from the vehicle. Follow the instructions for the correct model vehicle under FUEL TANK: EFI, REMOVAL in the Service Manual. 3. See FUEL PUMP/FUEL GAUGE SENDING UNIT, REMOVAL in the Service Manual for instructions to: a. Unplug the fuel pump module connector. b. Remove and discard the top plate screws. c. Remove the top plate, fuel pump and fuel level sender (fuel gauge sending unit) from the tank. NOTE Take care to avoid bending the fuel level sender float rod. A bent float rod will lead to erroneous gauge readings. 2 6 1 3 4 7 9 8 5 is05284 1. Fuel level sender 2. Electrical grounding tab 3. Fuel level sender lock tab 4. Adapter bracket 5. Slot (2) 6. Terminal strip insert 7. Sender to adapter lock tab 8. Slider 9. Adapter to tank lock tab Figure 1. Fuel Level Sender Assembly to Adapter – 4. See Figure 1. Clean the electrical grounding tab (2) on the back of the fuel level sender if necessary. The tab must make firm contact with the terminal strip insert (6) in the adapter bracket. Slide the original equipment (O.E.) fuel level sender (1) into the slots (5) in the new adapter bracket (4) as shown until the lock tabs (3 and 7) snap into place. Make sure the wire is not pinched between the adapter and sender. 5. See FUEL SUPPLY CHECK VALVE/TUBE in the Service Manual. Remove the check valve/quick-connect fitting assembly from the old fuel tank, and assemble to the new tank, using a new O-ring (purchased separately). 6. Fit the slider (8) on the adapter bracket into the fuel level sender mounting channel inside the tank, and push down until the lock tab (9) snaps into place. Make sure the sender and adapter wires are not pinched between the adapter and the fuel tank tunnel, and remain accessible through the fuel tank top opening. 7. See Figure 2. Obtain the assembly of the top plate (1), regulator (2) and fuel filter (3) removed from the old fuel tank, and the stainless steel screw (8) and nut (9) provided in this kit.

Incoming search terms:

HARLEY DAVIDSON ROAD KING SOLO BUCKET AND PASSENGER PILLION INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 10-02-2011

download
Installation SOLO SADDLE ONLY 1. Remove stock seat and grabstrap according to applicable Service Manual instructions. 2. Road King standard models . Remove and save the stock screws and seat mount bracket at the back of the rider solo seat. 2000 and later models . Remove the retainer washer from the stud plate and replace with two black retainer washers (2). Be careful not to allow stud plate to fall through the fender. 3. Road King standard models . Install stock solo seat mount bracket using two stock screws saved in Step 2. Road King Classic Custom models . Install solo seat mount bracket onto back of solo seat using bracket and screws included in Mount Kit Number 52903-01. 4. Install seat by sliding front of seat into seat holder bracket. Pull up on the nose of the seat to verify that the seat is securely installed. After installing seat, pull upward on front of seat to be sure it is in locked position. While riding, a loose seat can shift causing loss of control, which could result in death or serious injury. (00070a) 5. 1999 and later models . Install 1/4 in. star washers (6), spacers (4) and acorn nuts (3) onto rear mount studs. Torque to 72 in-lbs (8.13 Nm). 1998 and earlier models . Install 5/16 in. star washers (5) and 5/16-18 x 3/4 in. buttonhead screws (1) into stock mount nuts. Torque to 17 ft-lbs (23 Nm). SOLOAND PILLION 1. Remove stock seat and grabstrap according to applicable Service Manual instructions. Retain all hardware for later use. 2. Road King standard models . Remove and save the stock screws and seat mount bracket at the back of the rider seat. 3. Road King standard models. Install stock seat mount bracket onto new solo seat using two screws saved in Step 2. Road King Classic Custom models. Install solo seat mount bracket onto back of solo seat using bracket and screws included in Mount Kit Number 52903-01. 4. 1999 and later Road King standard models . Secure the rear mount bracket with stock mushroom nuts (10) and two 1/4 in. star washers (6). Torque to 72 in-lbs (8.13 Nm). 1998 and earlier Road King standard models . Install solo seat by sliding front of seat into holder bracket on bike. Secure the rear mount bracket with the two mushroom screws (11) and two 5/16 in. star washers (5). Torque to 17 ft-lbs (23 Nm). Road King Classic Custom models . Mount Kit Number 52903-01 is required for installation. Install solo seat (7) by sliding front of seat into holder bracket on bike. • 1999 and later models . Using Mount Kit Number 52903-01, secure the rear mount bracket with the two mushroom nuts (10) and two 1/4 in. star washers (6). Torque to 72 in-lbs (8.13 Nm). • 1998 and earlier models . Using Mount Kit Number 52903-01, secure the rear mount bracket with the two mushroom screws (11) and two 5/16 in. star washers (5). Torque to 17 ft-lbs (23 Nm)

Incoming search terms:

2001-2003 XV16 Fuel Pump and Carburetor Removal

0

Filed Under (Yamaha) by admin on 31-12-2011

download
Disconnect the carburetor fuel line hose at the fuel pump. •Disconnect the fuel pump wire coupler. •Remove the choke cable from fuel pump bracket. •Remove the upper engine mount, leaving the fuel pump attached to the mount. •Disconnect the TPS and carburetor wire couplers.       Disconnect the throttle cables, and then remove the carburetor. NOTE: The idle adjuster can be removed from its bracket without loosening the bracket screws. PAGE 3 of 12 HIDDEN 6mm SCREW 6mm BOLT UPPER ENGINE MOUNT/ FUEL PUMP CARBURETOR PAGE 4 of 12 Right-Hand Footrest Removal: •Disconnect and remove the brake light switch. •Remove the forward-most tie wrap around the brake hose and frame. •Remove the footrest assembly. NOTE: Leave the brake hose attached. Move the hose to the underside of the foot rest mount and support it as necessary so that it is out of the way Cylinder Head Oil Pipe Removal/ Installation: •Slightly loosen all three banjo bolts before removing them to prevent oil line deformation. NOTE: When loosening the upper banjo bolts, hold the line in place using a wrench at the flat surface on the fitting. Air Injection System (AIS) Removal: •Remove the electric starter motor. •Remove the regulator/rectifier assembly. Remove the AIS pipes from the cylinder head, but leave them attached to the AIS assembly. •Remove the three screws with 8mm heads, and then remove the AIS air filter from the right side. •Remove the three Phillips head screws holding    the AIS assembly on the frame. •Remove the AIS assembly from the left side. FOOTREST ASSEMBLY UPPER BANJO BOLT AIS AIR FILTER AIS ASSEMBLY
PAGE 5 of 12 Transfer Case Removal: •Remove the transfer case bracket first. Then remove the outer chrome cover, inner cover, and drive-sprocket nut. NOTE: There is a sealing washer between the inner case and the transfer case at the 8mm stud. Be sure to replace it during re-assembly. •Remove the two chrome oil lines between the engine and oil tank. NOTE: Retain the four O-rings for re-use. •Remove the drive pulley cover and remove the drive pulley nut. •Loosen the drive belt tension. •Remove the drive pulley, inner cover, collar, and O-ring. NOTE: The collar has a bevel on its inside diameter     for the O-ring facing inward and a bevel on the outside diameter facing the pulley. •Remove the drive and driven sprockets with chain as an assembly. •Remove the collar and O-ring. NOTE: Collar has a bevel on its inside diameter that faces inward for the O-ring. •Remove oil tank filler neck. •Remove the relay bracket on the right-hand side. NOTE: Leave the relays connected. Simply move them out of the way to allow room for transfer case removal. •Slide the transfer case out from the right side.

Incoming search terms:

Victory Freedom Engines Installation Instructions for S&S Air Cleaner Kit

0

Filed Under (Victory) by admin on 31-10-2010

download
1-Locate and remove the Intake Air Temperature Sensor (IATS) from the stock Polaris Victory air box. Locate the new position for the IATS on the bottom of the S&S air cleaner. Push the IATS in the lower air cleaner cover and turn1⁄ 4 turnin either direction, make sure you feel it lock into place. Inspect from the inside of the air cleaner to ensure that the barbs are locked into place. See Picture 1. 2-Using the stock Polaris Victory air box gasket (PN 5811908) and S&S supplied (Qty 4) M6 fasteners, assemble the lower air cleaner cover to the throttle body using 243 Blue Loctite®on the treads. Torque the M6 fasteners to 72-96 inch pounds. 3-Position the S&S pre-formed air filter onto the lower air cleaner cover ensuring that it fits into the machined groove. 4-Install the top air cleaner cover on top of the filter ensuring that it fits into the machined groove. 5-Make surethat the filter is situated in the machined grooves on both the top and bottom air cleaner covers. 6-Using 243 Blue Loctite on the threads of the S&S supplied (Qty 3) M6 fasteners tighten down top air cleaner cover evenly until seated. Finish torque the fasteners to 72-96 inch pounds. Now you’re ready for breather hose and barometric pressure hose routing. 7-Locate the S&S supplied 3⁄ 16 “reinforced hose and clamps. Push one end of the hose on the 3⁄ 16 “brass barb in the bottom air cleaner cover and slide clamp up around the end of the hose. The other end of the hose is for the Barometric Pressure Sensor (MAP). Route the hose towardthe back of the engine over the top of the rear rocker cover. 8-Remove the MAP sensor from the stock Polaris Victory air box. Remove the orange rubber gasket from the MAP sensor. Slide the S&S supplied clamp over the 3⁄ 16 “rubber hose that leads to the air cleaner. Push the barbed end of the MAP sensor into the 3⁄ 16 ” rubber hose and slide clamp up to the end of the hose around the barb. A small amount of lubricant may be applied to the barb on the MAP sensor to make installation easier. 2 S&S Air Cleaner Assembly 41-0021 (Calibration cardnot shown) Picture 1 CAUTION WARNING WARNING Plastic barb locked in recess.
9-Assemble and install breather hose as follows: A-Cut the stock Victory®hose on the straight section just behind the 90 degree bend as shown in Picture 2 . B-Slide an S&S supplied 1⁄ 2 “hose clamp over the modified stock breather hose. C-Install the S&S straight barb in Victory breather hose and position a hose clamp around hose end. D-Slide the 90-degree end of breather hose over the brass barb on the air cleaner cover and slide hose clamp in place. E-Position straight end of the S&S breather hose over the 1⁄ 2 “barb to connect to the Victory hose. Slide clamp over connection. F- See Pictures 3 and 4 for breather hose and barometric pressuresensor hose installation positions. NOTE: S&S breather hose can be cut for best fit

Incoming search terms:

Carbureted vs. Fuel Injected Systems

0

Filed Under (Tips and Review) by admin on 25-10-2010

download
fuel injection (FI) systems have been around since the 1950′s and became widely used in cars during the 80′s. By the 1990′s all cars sold in the United States were equipped with FI systems, and though motorcycle manufacturers have included FI systems with some models as early as 1982, it isn’t until recently that the industry has seen wide spread use of FI. Since a lot of people come into my shop with questions about FI, I thought I would point out some of the differences between FI and carbureted systems as well as the benefits and disadvantages of both. A carbureted system is a mechanical system using air pressure to control the flow of fuel through the system. There are three basic parts in a carburetor, the throttle valve, the venturi and the float bowl. The throttle valve controls the amount of air that flows into the throat of the carburetor also known as the venturi which is simply a tapered hole through the carburetor body. As the venturi narrows, air moving through it is forced to speed up creating low pressure inside the carburetor. In a siphoning effect as the air tries to equalize the pressure, fuel is drawn in from the float bowl mixing with the air before entering the engine. The wider open the throttle valve, the more air will flow, drawing more fuel. A number of circuits are built into the carburetor in order to control the amount of air/fuel being drawn into the engine. In this context a circuit refers to a fuel passageway as opposed to an electrical circuit. In fact, nothing electrical controls fuel delivery in a carbureted system, it is all based on fluid flow, vacuum and hydraulics. The different circuits represent various throttle positions such as idle, partially open and fully open, and each of these circuits can be tuned to modify the efficiency of fuel delivery to the system. Fuel injection (FI) systems, on the other hand, rely on an electronic fuel pump to deliver fuel. The fuel pump delivers fuel at around 50psi as opposed to carbureted systems at normal atmospheric pressure of about 15psi. When the fuel reaches the injectors, the higher pressure allows much finer atomization (creating mist) of the fuel. The injectors then spray the atomized fuel into the intake manifold in a uniform conical pattern. The uniform pattern and fine atomization of the fuel spray increase the efficiency in which it is burned

How to change a fuel filter on 1998 Ducati ST2

0

Filed Under (Ducati) by admin on 26-10-2010

download
1. On a cool bike, parked on center-stand, remove the two button-head bolts securing the key cover on the top of the fuel tank. Set cover aside, and save bolts, they will be used later. 2. Remove the seat 3. Un-hook front clip holding the tank down. 4. Lift tank upward, rotating on rear pin, and place prop-rod in place to secure tank in upright position. (If possible, you may want to find a longer prop to put the tank at a higher angle. This allows the fuel pump to be a bit more accessible. I used a long piece of rod iron, and propped the tank up by its rubber side bumpers.) 5. Pad the area directly under the fuel pump very well with paper shop towels or other very absorbent materials, as gas will likely drip. 6. Disconnect the electrical connector going to the fuel pump.
7. There are two fuel lines going to the fuel pump. One is marked with a white collar that has the letter R on it, the other has a M . Take note of which is which. The R line goes in the middle stem, and the M connects to the stem that is closest to the outside edge of the tank. It is a good idea to take a permanent marker, and write a ” R ” and ” M ” near these connections on the bottom of the fuel filter so as to not forget. 8. One at a time, loosen the hose clamps on the lines, and remove them from their stems. Some fuel will spill. It will stop however; have plenty of paper-towels close on hand. (The hose clamps should be 7mm) Also remove the small gas overflow tube that is attached to the fuel pump. 9. Remove the rear latch that the tank rotates on, and lift the tank off of the bike. 10. Lean the tank forward so as to move the gas forward, and remove the drain plug at the very rear of the tank with a 5mm Hex Key

Incoming search terms: