2008 teryx how to adjust idle

You search Auto repair manual PDF 2008 teryx how to adjust idle, if there are search results will appear below. If search results do not exist, please search by others keyword.



  2008 teryx how to adjust idle Direct Download speed 5282 Kb/s

  2008 teryx how to adjust idle Full Version speed 6162 Kb/s



Ural carburetors Installation and idle adjustment

0

Filed Under (Ural) by admin on 02-11-2010

download
1. First you must adjust the idle. It is acceptable per the manual to adjust the idle by using the idle adjust screws (11). This usually involves screwing them then backing out 1 to 1.5 turns. Or you can adjust looking at the sliders 2. If installing the carburetors: a. Remove the cover (2) b. Reomve the slider (3) c. Place the throttle cable through the guide (18) with the spring (4) on the cable. d. Route the cable through the slide catch (6) e. Insert the slide assembly into the chamber and make sure it easily slides up and down. Direct the needle (8) into the opening of the diffuser (angled side visible). f. Screw assembly together and verify via throttle movement that slide moves freely. Attach fuel delivery lines to (12). 3. Using the idle set screw (11) raise the slider so the lower edge is 1-2 mm. 4. Assemble to engine using the proper gaskets (paper – felt – paper). 5. Using the locknut (26) adjust the free play of the throttle cable (2-3 mm) 6. Adjust the idle mixture screw – turn in completely then out 1 to 1.5 turns 1. Remove one of the spark plug caps, and with the cap shorted, adjust (11) to decrease RPM’s to a point of being minimally steady. 2. Adjust the mixture (15) out until RPM’s decrease. Turn in until RPM’s increase slightly. Then turn in screws ¼ to 1/3 revoultion. 3. Do the same for the second carburetor with the first spark plug cap shorted. 4. With both cylinders, adjust each idle (11) on each carburetor the same amount each until it’s at a steady, minimal RPM. Use small changes. (at this point you can use your airflow tool to check). 5. Sharply increase, then decrease throttle. Then engine must return to low RPMs smoothly. If the engine goes below limits, readjust (11) from step 4. Synchronization of the K68 Note: Rather than using the opposite cylinder shorted to test the pull of the live cylinder carburetor, you can use something like a Twinmax connected to the test ports (27 Fig 1). Or, if you have a model without these ports, use a Synchrometer (Appendix 2) held against the face of the carburetor. These tools merely show airflow passing through each carburetor (which is dependent on the position and wear on the slide). If using these tools, it’s not necessary to do the following steps. You wil want to use a throttle guide (Appendix 1), to show airflow at various throttle settings. Using the flow meter of your choice make sure each carburetor is the same at the various throttle settings. 1. Place the motorcycle on the center stand ensuring the rear wheel is suspended 2. Make sure you have large area to work with (safety issues here) 3. Shift into the highest gear with the engine running 4. Short one spark plug cap to the cylinder (using a nail or something in the fins) 5. Increase the speed to 40-50 km/hr 6. Fix the throttle using the throttle (maybe using a throttle stop screw under the throttle housing). 7. Reconnect other cylinder and using the opposite carburetor determine the speed which should be the same as the first. 8. Adjust the position of this slide to achieve the referenced speed using the locknut at the top of the carburetor.

Incoming search terms:

Adjusting the Pekar K68 for Dnepr or Ural

0

Filed Under (Tips and Review) by admin on 11-11-2010

download
1. Make sure the ignition timing is correct 2. Adjust the valves as necessary to ensure proper operation 3. Run the engine to warm it up a bit 4. Adjust the float setting. To do this, remove the carburetors (leave the throttle cables attached), remove the bowl and turn the carburetor upside down (fuel will spill). The float should look like this: Adjust as necessary by bending the float support (#37 in Figure 1). Reinstall Installation and idle adjustment 1. First you must adjust the idle. It is acceptable per the manual to adjust the idle by using the idle adjust screws (11). This usually involves screwing them then backing out 1 to 1.5 turns. Or you can adjust looking at the sliders 2. If installing the carburetors: a. Remove the cover (2) b. Reomve the slider (3) c. Place the throttle cable through the guide (18) with the spring (4) on the cable. d. Route the cable through the slide catch (6) e. Insert the slide assembly into the chamber and make sure it easily slides up and down. Direct the needle (8) into the opening of the diffuser (angled side visible). f. Screw assembly together and verify via throttle movement that slide moves freely. Attach fuel delivery lines to (12). 3. Using the idle set screw (11) raise the slider so the lower edge is 1-2 mm. 4. Assemble to engine using the proper gaskets (paper – felt – paper). 5. Using the locknut (26) adjust the free play of the throttle cable (2-3 mm) 6. Adjust the idle mixture screw – turn in completely then out 1 to 1.5 turns. * Starting using the K68′s (cold weather) 1. Verify fuel flow. Apply choke (pull 52 in Fig1). 2. Using the ticklers (13) allow fuel to enter the bowl until fuel drains from (14) 3. With the ignition off, kick 1 or 2 times 4. Turn ignition on, and as soon as engine is warmed up (maybe sooner) push choke mechanisms to open choke Idle Adjustment (engine running and warm) 1. Remove one of the spark plug caps, and with the cap shorted, adjust (11) to decrease RPM’s to a point of being minimally steady. 2. Adjust the mixture (15) out until RPM’s decrease. Turn in until RPM’s increase slightly. Then turn in screws ¼ to 1/3 revoultion. 3. Do the same for the second carburetor with the first spark plug cap shorted. 4. With both cylinders, adjust each idle (11) on each carburetor the same amount each until it’s at a steady, minimal RPM. Use small changes. (at this point you can use your airflow tool to check). 5. Sharply increase, then decrease throttle. Then engine must return to low RPMs smoothly. If the engine goes below limits, readjust (11) from step 4. Synchronization of the K68 Note: Rather than using the opposite cylinder shorted to test the pull of the live cylinder carburetor, you can use something like a Twinmax connected to the test ports (27 Fig 1). Or, if you have a model without these ports, use a Synchrometer (Appendix 2) held against the face of the carburetor. These tools merely show airflow passing through each carburetor (which is dependent on the position and wear on the slide). If using these tools, it’s not necessary to do the following steps. You wil want to use a throttle guide (Appendix 1), to show airflow at various throttle settings. Using the flow meter of your choice make sure each carburetor is the same at the various throttle settings. 1. Place the motorcycle on the center stand ensuring the rear wheel is suspended 2. Make sure you have large area to work with (safety issues here) 3. Shift into the highest gear with the engine running 4. Short one spark plug cap to the cylinder (using a nail or something in the fins) 5. Increase the speed to 40-50 km/hr 6. Fix the throttle using the throttle (maybe using a throttle stop screw under the throttle housing). 7. Reconnect other cylinder and using the opposite carburetor determine the speed which should be the same as the first. 8. Adjust the position of this slide to achieve the referenced speed using the locknut at the top of the carburetor.

Incoming search terms:

KAWASAKI TERYX EFI Installation Instructions.

0

Filed Under (Kawasaki) by admin on 08-02-2011

download
Basic Tuning Adjustments 1. The following instructions are for basic fuel tuning. Modes 1,2, & 3 are allowing adjustments to increase and decrease the amount of fuel the engine needs. Modes 4 & 5 are for advanced tuning only. DO NOT change modes 4 & 5 when doing basic tuning! 2. To help understand how these modes work, you can think of them as if you were working with a carburetor. 3. Remember each time you push the MODE button you will be advancing to the next mode. Push the MODE button once and you are now in mode 1, push the MODE button again and you are now in mode 2 and so on. You only need to be concerned with modes 1, 2 & 3 for basic tuning. Modes 4 & 5 are for advanced tuning ONLY. 4. If you need to go back to the settings that were pre programmed when you purchased the controller, just look at the picture in each mode, the colored square represents where the settings were when you purchased the controller. 5. Looking at the controller you will see eight lights with numbers under them, this is what you need to look at when changing settings. The #1 light on the controller represents the leanest setting. TRINITY RACING DOES NOT TAKE REPONSIBLITY FOR DAMAGES THAT MAY OCCUR DURING OPERATION OF YOUR VEHICLE UNDER IMPROPER JET SETTINGS. IT IS THE FINAL RESPONSIBLITY OF THE OWNER/RIDER TO ADJUST JETTING TO SPECIFIC RIDING CONDITIONS AND ELEVATION BEFORE RIDING. WARNING! 1.877.FAS TOYS 2.Remove both seats 6. Re-install engine cover and seats. 6. Mode 1 green light represents idle & cruise adjustment (i.e. pilot jet). To adjust this setting push the MODE button once and then push the plus or minus buttons to adjust fuel as needed. 7. Mode 2 yellow light represents an additional amount of fuel added during acceleration (i.e. needle position). To adjust this setting, push MODE twice and then push the plus or minus buttons to adjust fuel as needed. 12 34 56 7 8 12 34 56 7 8 8. Mode 3 red light represents more fuel being added during full throttle (i.e. main jet). To adjust this setting push the MODE button three times and then push the plus or minus buttons to adjust fuel as needed. 9. If you are confident about your tuning skills and feel you need to adjust other parameters, see Advanced Tuning. 12 34 56 7 8 Advanced Tuning Adjustments 1. Advance tuning has two modes in which to adjust. They are called mode 4 and mode 5. In basic tuning, you are changing the amount of fuel that the engine receives, but with advance tuning, you will be changing when the fuel will be available. In each mode you can adjust how soon the fuel delivery occurs. 2. Mode 4 yellow light and blue light represent when the fuel delivery is available during partial throttle acceleration. To adjust this setting, push the MODE button four times and then push the plus or minus buttons to adjust fuel as needed. Only the yellow light will be changing.

Incoming search terms:

2003 – 2008 4Runner AND 2007 – 2008 FJ Cruiser FRONT AND REAR DIFFERENTIAL GEAR OIL SPECIFICATION CHANGE

0

Filed Under (Toyota Manuals) by admin on 14-11-2011

download
75W-85 GL5 synthetic gear oil beginning with the 2008 model year. This new synthetic gear oil is compatible with 2003 – 2007 model year 4Runner and 2007 model year FJ Cruiser differentials. Please refer to the Parts Information section below for information about this gear oil and use this gear oil (or equivalent) when filling front or rear differentials with oil. 2003 – 2008 model year 4Runner vehicles. 2007 – 2008 model year FJ Cruiser vehicles. PREVIOUS PART NUMBER CURRENT PART NUMBER PART NAME TYPE QTY N/A 08885-02606 Toyota Genuine Differential Gear Oil LX 75W-85 API GL-5 SAE 75W-85 LSD As Needed N/A 08885-02506 Toyota Genuine Differential Gear Oil LT 75W-85 API GL-5 SAE 75W-85 w/o LSD As Needed Refer to the diagram below to identify if LSD or non-LSD gear oil is used on the vehicle. For applicable vehicles, there is a caution label above the filler plug, as shown below

Incoming search terms:

2008-2009 KAWASAKI TERYX HEADLAMPS HIDTERYX HID KIT INSTALLATION INSTRUCTIONS

0

Filed Under (Kawasaki) by admin on 25-10-2010

download
a. Remove rubber boot from the back of the headlamp housing assembly. b. Push down on metal latch and pull away from lip to release halogen bulb. Pull out halogen bulb. c. Insert HID bulb, line up bulb to fit into the bulb holder, lower latch to lock bulb in place. d. Replace Rubber boot on the back headlamp assembly. (Make sure to pull wires through the center of the rubber boot first before you start to pull down boot on the back of the headlamp assembly.) e. Make sure that the wiring, coming from the HID bulb, clears the black plastic housing that encases the headlamp assembly so connection from the bulb to the ballast is possible. If installed correctly there is no need for drilling or modifications of any type. 2. Ballast a. Mount ballast in location of your choice – recommended near the headlight. 3. Wiring Note: DO NOT modify the wiring that runs from the HID bulb to the ballast. It will cause the system to work improperly. It will void the warranty . a. Once ballast is installed connect corresponding wires from HID bulb to corresponding male / female plugs on ballast. b. To connect wiring from ballast to Teryx primary system i. Find wire extension with white triangular head with black, yellow & green wires at opposite end ii. Connect black off extension to black wire coming off ballast iii. Connect Yellow / Green wire to red wire coming off ballast iv. Connect triangular head to corresponding plug on Teryx Factory Wiring End

HARLEY DAVIDSON MULTI-FIT BRAIDED THROTTLE/IDLE CABLE KITS REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 20-03-2011

download
REMOVAL To prevent accidental vehicle start-up, which could cause death or serious injury, disconnect negative (-) battery cable before proceeding. (00048a) To prevent accidental vehicle start-up, which could cause death or serious injury, remove main fuse before proceeding. (00251b) 1. Disconnect battery cables, negative (-) cable first or remove the main fuse following the instructions in the service manual. NOTE When performing cable disassembly procedures, make careful notes as to the existing cable routing. Pay special attention to existing cable strap locations before removing so new straps can be installed in the same locations. Do not remove or install the master cylinder assembly without first positioning a 5/32-inch (4 mm) thick insert between the brake lever and lever bracket. Removing or installing the master cylinder assembly without the insert in place may result in damage to the rubber boot and plunger on the front stoplight switch. (00324a) 2. See Figure 1. Place the cardboard insert between the brake lever and lever bracket. 3 2 1 is00825 1. Brake lever 2.5/32 inch (4 mm) cardboard insert 3. Brake lever bracket Figure 1. Install Cardboard Insert 3. See Figure 2. Loosen cable adjuster jam nuts. Turn cable adjusters in until they are as short as possible. This will provide enough slack for easy removal. 3 4 1 2 5 is 02071 1. Upper switch housing 2. Lower switch housing 3. Throttle cable adjuster 4. Idle cable adjuster 5. Adjuster jam nut Figure 2. Handlebar Throttle Control 4. Remove the right upper and lower switch housing screws. 5. Loosen the upper screw securing the handlebar clamp to the master cylinder housing. Remove the lower clamp screw and flat washer. NOTE If possible, leave the friction shoe in place. The friction shoe is a loose-fit and may fall out or become dislodged if the lower switch housing is turned upside down or shaken. 6. See Figure 3. Remove the brass ferrules from the notches on the inboard side of the throttle control grip. Remove the ferrules from the cable end fittings. 1 2 4 3 is 02072 1. Throttle cable 2. Idle cable 3. Brass ferrule 4. Notch Figure 3. Throttle/Idle Control Cables 7. Pull the crimped inserts at the end of the throttle and idle control cable housings from the lower switch housing. For best results, use a rocking motion while pulling. Remove cables with retaining rings from switch housing. Apply a drop of light oil on the retaining ring, if necessary, to help in removal. NOTE If installing different handlebars, measure the change in distance that will be required from the end of the cable housing to the throttle grip. Compare this additional required length to the cables provided in the kit. If the cables are more than 2.0 inches (51 mm) longer or more than 1.0 inch (25 mm) shorter than the above measured distance, see a Harley-Davidson dealer for the correct cable length. Install proper length throttle cables. Incorrect cable length can adversely affect motorcycle operation, which could cause loss of control resulting in death or serious injury. (00396b) 8. Follow instructions in the applicable service manual and remove air cleaner and backplate.

Incoming search terms:

HARLEY DAVIDSON MULTI-FIT BRAIDED THROTTLE/ IDLE CABLE KITS REMOVAL AND INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 01-02-2011

download
REMOVAL To prevent accidental vehicle start-up, which could cause death or serious injury, disconnect negative (-) battery cable before proceeding. (00048a) 1. Disconnect battery cables, negative (-) cable first or remove the main fuse following the instructions in the service manual. NOTE When performing cable disassembly procedures, make careful notes as to the existing cable routing. Pay special attention to existing cable strap locations before removing so new straps can be placed into the same locations. Do not remove or install the master cylinder assembly without first positioning a 5/32-inch (4 mm) thick insert between the brake lever and lever bracket. Removing or installing the master cylinder assembly without the insert in place may result in damage to the rubber boot and plunger on the front stoplight switch. (00324a) 2. See Figure 1. Place the cardboard insert between the brake lever and lever bracket. 3. See Figure 2. Loosen cable adjuster jam nuts. Turn cable adjusters in until they are as short as possible. This will provide enough slack for easy removal. 4. Remove the right upper and lower switch housing screws INSTALLATION Throttle and Idle Cable Installation 1. See Figure 3. Apply graphite lightly to the throttle grip inside the switch housing and on the throttle end of the handlebar. NOTE The throttle control cable has a larger diameter retaining ring crimped to the cable end than does the idle control cable. For assembly, apply a drop of light oil on the retaining rings of the crimped inserts. 2. See Figure 7. Push the throttle cable housing and retaining ring into the larger hole of the switch housing, located in front of the tension adjuster screw. 3. Push the idle cable housing and retaining ring into the smaller hole of the switch housing, located behind the tension adjuster screw. 4. Push the throttle and idle control cable housings into the lower switch housing until each snaps into place. NOTE For models not equipped with factory-installed cruise control, if the friction shoe has fallen out or become dislodged, install the shoe with the concave side facing up and position it so the pin hole is over the point of the adjuster screw. 5. Push the throttle control grip over the end of the right handlebar until it bottoms against the closed end. Rotate the grip until the ferrule notches are at the top. To prevent binding, pull the grip back about 0.12 inch (3.2 mm). 6. See Figure 3. Position the lower switch housing beneath the throttle control grip. Install two brass ferrules (Item 3, Figure 11) from this kit onto cables, seating the ferrules in their respective notches on the throttle control grip. The cables must be captured in the grooves molded into the grip. 7. Position the upper switch housing over the handlebar and lower switch housing. Route the wire harness conduit through the depression at the bottom of the handlebar. 8. Tighten the upper and lower switch housing screws finger- tight. 9. Position the brake lever/master cylinder assembly inboard of the switch housing assembly, engaging the tab on the lower switch housing in the groove at the top of the brake lever bracket. 10. Align the holes in the handlebar clamp with those in the master cylinder housing and tighten the lower screw and flat washer finger-tight. Position for rider comfort. Beginning with the top screw, tighten the screws to 60-80 in-lbs (6.8-9.0 Nm)

Cobra 2008 CX50SR (King) Ignition System installation Manual

0

Filed Under (Cobra) by admin on 10-11-2010

download
Many 2008 Cobra CX50SR (King) customers are experiencing performance issues with their new motorcycles. These issues include cracking/popping noises, degrading performance, and excessively hot exhaust pipes. These issues have been traced back to manufacturing flaws with the new IDM brand ignition system. Because of the time associated with getting these issues sorted out, Cobra is switching production of the 2008 King over to the PVL brand ignition system (the same design used on 2007 model King motorcycles). Customers with 2008 Kings built prior to this date may exchange it for a PVL system at no cost for the hardware. For existing product in the field, Cobra will not support the IDM system until our supplier has their component functioning properly. To install the PVL system on the 2008 King simply remove the old hardware, and bolt on new (an updated Cobra universal puller will be required to remove the ignition rotor). The timing of the new PVL system will have to be set properly during installation

Kawasaki FI Calibration Tool Instruction Manual

0

Filed Under (Kawasaki) by admin on 08-02-2011

download
System Function Kawasaki FI Calibration Tool (FI Tool) is developed to modify the mapping of the racing machine to gain operating conditions suitable for the course and the rider’s skill. The following are the available setting functions. Table 1 FI Tool Function Model Name Functions Available Setting Range ’04 ZX-10R ’05 ZX-6RR ’05 ZX-10R ’06 ZX-10R ’07 ZX-6R 1) Adjust the injected fuel rate at acceleration -30 % ~ +30 % 〇 〇 〇 〇 〇 2) Adjust the injected fuel rate of No.1 and No.4 cylinder -30 % ~ +30 % 〇 〇 〇 〇 〇 3) Adjust the injected fuel rate of No.2 and No.3 cylinder -30 % ~ +30 % 〇 〇 〇 〇 〇 4) Adjust the injected fuel rate of primary and secondary injector * -30 % ~ +30 % -10 % ~ +10 % — – — 〇 — – — – — 〇 5) Adjust the ignition timing -15°CA~ +5°CA 〇 〇 〇 〇 〇 6) Adjust the sub-throttle opening angle -50 % ~ +50 % -45 % ~ +45 % 〇 — – 〇 〇 — 〇 — – 〇 7) Adjust the exhaust device opening angle -50 % ~ +50 % 〇 — 〇 〇 — 8) Adjust the all injected fuel rates of all cylinders and operating are a simultaneously -30 % ~ +30 % 〇 〇 〇 〇 〇 9) Adjust the value of engine over revolution limiter 0 ~ +300 rpm -1000 ~ +700rpm -1000 ~+1200rpm — – — 〇 — – — 〇 — – — 〇 〇 — – 10) Set the fuel cut or not at deceleration Use or Not Use 〇 〇 〇 〇 〇 11) Set the sub throttle controlled or not Controlled or Full Open Fixed 〇 — – — – 12) Set the exhaust device controlled or not Controlled or Full Open Fixed 〇 〇 〇 〇 〇 13) Set the Auto Shifter Ignition Cut Length Controlled or not, set Ig. Cut Time by gear range — – 〇 〇 〇 14) Set the Pit Road RPM Limit Controlled or not, set Upper Limit RPM by gear range

Kawasaki Teryx 750 Cab Enclosure Kit Installation And Removal Manual

0

Filed Under (Kawasaki) by admin on 25-10-2010

download
Remove seats and set aside for better access to vehicle interior. Refer to Owner’s Manual for instructions. ii) Remove lower foot guardrails and set shoulder screws aside for later use. Loosen 19mm bolts ( A in Fig.1) until 3/16″ gap can be achieved. iii) Loosely fasten rubber stops ( B in Fig.1) to Hinge Mounting Brackets using 6mm bolts. Mount brackets to vehicle as shown in Fig.1 and hand tighten 19mm bolts. iv) Align lower bracket hole to existing foot guard mounting hole and fasten with OEM shoulder screw ( C in Fig.1). NOTE : Apply pressure to screwdriver in order catch threads on nuts. v) Adjust upper edge of brackets with mallet to make bracket edge flush to roll bar edge (Fig.2). Tighten 19mm bolts. Adjust and tighten rubber mounts. FLUSH A B Fig.2 Fig.1 2. Rear Bracketery i) Remove 14mm bolts from lower mounting points on rear crossbar. Install Striker Mounting Brackets as shown (Fig.3). Reinstall bolts and hand tighten only . Attach Striker Plates using (4) ¼-20 x 3/8″ screws, keep loose for later adjustment. ii) Remove 14mm bolts from upper crossbar and install Upper Rear Panel Brackets as shown (Fig.4). Tighten 14mm bolts back into place. 3. Panel Installation i) Install low density foam to interior of panels as shown (Fig.5.) Approx. (8) 3″ long strip are required on each side panel. Install low density foam to entire door / panel interface. ii) Mount side panels to roll cage and temporarily clamp to top roll bar. Loosely insert remaining (2) shoulder screws to each foot well. Adjust each panel to obtain proper alignment at front, top and lower rear. iii) Ensure hinge mounting bracket edges are flush with inside door frame and transfer hinge bolt hole locations onto plastic panels. Remove panels and drill holes using ¼” bit. Re-install panels and shoulder screws onto vehicle. iv) Mount hinges as shown (Fig.6) with (8) ¼-20 x 5/8″ Lg. Flat Head screws. DO NOT OVER TIGHTEN

Incoming search terms: