2008 yamaha raider remove brake light

You search Auto repair manual PDF 2008 yamaha raider remove brake light, if there are search results will appear below. If search results do not exist, please search by others keyword.



  2008 yamaha raider remove brake light Direct Download speed 5282 Kb/s

  2008 yamaha raider remove brake light Full Version speed 6162 Kb/s



1999-2008 FLHT Series Harley- Davidson Trike Conversion Kit Installation Instructions

0

Filed Under (Harley Davidson) by admin on 04-12-2010

download
1. Place the motorcycle on the lift. 2. Place a suitable Jack under the Frame of the Motorcycle and tie down securely. 3. Remove Drain Plug from Primary Cover Assembly and drain oil. 4. Slide Rubber Boot off of the Clutch Cable Adjuster. Loosen and back the Jam nut away from the Clutch Cable Adjuster. Move Clutch Cable Adjuster towards the Jam Nut to introduce free play in the Clutch Lever. 5. Remove the ¼ – 20 Phillips head screw and Seat. 6. Disconnect negative Battery Terminal. 7. Remove two ¼ – 20 flanged hex nuts from the Stud Plate. Save the Passenger Handrail and two nuts. 8. Remove the Saddle Bags. 9. Remove the Right and Left Side Covers. 10. Remove Inner Tour Pak Molded Liner. 11. Disconnect the Tour Pak wiring. 12. Remove five ¼ – 20 HHCS, ¼ – 20 nyloc nuts, and Aluminum Spacers. 13. Remove Tour Pak from Top Support Tube. 14. Loosen Muffler Clamp on both Mufflers and remove 2 5/16 – 18 HHCS per Muffler. Remove and discard both Mufflers. Save Muffler Clamps. 15. Remove and discard Muffler Support Plates. 16. Remove both ¼ – 20 HHCS and Front Saddle Bag Brackets. 17. Remove the twelve 5/16 – 18 Torx HCS six 5/16 – 18 nuts, and the Left and Right Saddle Bag Guards. 18. Remove the Air Line Junction from the Rear Fender. 19. Disconnect the Rear Lamp Wiring Harness and remove from T-stud Clip.
6 20. Remove two 5/16 – 18 Phillips head screws. Remove the Left and Right Frame Covers. 21. Remove two 5/16 – 18 Torx HCS. Remove and save the Top Tour Pak Support Tube Top. 22. Remove four 5/16 – 18 Torx HCS. Remove the Left and Right Rear Saddle Bag Guard Support Bracket. 23. Remove four 5/16 – 18 HHCS. Remove and save the Tour Pak Support Tube Bottom. 24. Remove and discard the Air Valve Assembly Bracket. 25. Remove four ½ – 13 HHCS and washers. Remove and discard both Rear Air Shock Absorbers. NOTE: if ABS equipped refer to separate instructions. NOTE: if ABS equipped refer to separate instructions. NOTE: if ABS equipped refer to separate instructions. NOTE: if ABS equipped refer to separate instructions. 26. Drain all Brake Fluid from the Rear Brake System. 27. Cut and remove Cable ties and un-clamp Wire Harness Loops from the Rear Brake Line along its length, including Clamps on Swing Arm. 28. Remove the 10 – 24 flanged HHCS and Rear Brake Hose Clamp from the Right Rear Fork Bracket. 29. Remove ¼ – 20 SHCS from Rear Stop Lamp Switch Bracket. 30. Remove and discard Banjo Bolt and Crush Washers on Rear Brake Caliper. 31. Remove the Spring Clip and nut from the Rear Axle. 32. Remove Rear Axle and Rear Wheel Spacers. 33. Push Rear Wheel Assembly forward and slip Rear Belt off of the Rear Sprocket. 34. Remove Rear Brake Caliper. 35. Slide Rear Wheel Assembly rearward. Remove one 5/16 – 18 Torx HCS from inside the Rear Fender well. 36. Slide Rear Wheel Assembly forward. Remove two 5/16 – 18 Torx HCS. Remove Rear Fender. 37. Remove and save the two Retaining Washers from the Stud Plate. Remove and save the Stud Plate

Incoming search terms:

GL1800 Goldwing Trike Conversion Kit Installation Instructions

0

Filed Under (Honda) by admin on 10-11-2010

download
Disassembly of motorcycle: 1. Place the motorcycle on the center stand or lift. 2. Set the shock preload to zero. 3. Remove the four m8 x 1.25 SHCS from the passenger handles and remove seat. 4. Remove the rear side covers. 5. Disconnect negative battery terminal. 6. Remove the four m8 x 1.25 SHCS and the passenger floorboards. 7. Remove the six m5 x 0.80 BHCS and the foot rest under cover. 8. Remove the six m5 x .80 BHCS and the swing arm pivot bolt covers. 9. Remove the four m8 x 1.25 flange bolts on the rear crash guards. Remove and discard the rear crash guards and bolts. 10. Remove the four #2 Phillips head screws from the inside of the trunk to remove the trim pieces on the sides. 11. Remove the two #2 Phillips head screws in the rear trim molding and remove molding. 12. Remove the seven #2 Phillips head screws from the lower trunk cover. Remove the lower trunk cover. 13. Remove the five #2 Phillips head screws from the trunk opener cover. Remove the trunk opener cover. 14. Disconnect the left and right saddlebag release cables. 15. Remove the five m6 x 1.0 BHCS in the rear fender panel. Remove and discard the rear fender panel and cap screws. 16. Disconnect the trunk wiring. 17. Remove the four m6 x 1.0 flange screws. Remove the trunk from the saddlebag / trunk stay. 7 18. 2005 and older 2005 and older 2005 and older 2005 and older ABS equipped motorcycles: ABS equipped motorcycles: ABS equipped motorcycles: ABS equipped motorcycles: Remove rubber bungee from ABS Control Unit, and save for reinstallation. 19. Remove the two side cover grommets from each saddlebag. ( 4 grommets total ) 20. Remove the left and right hand saddlebag latches, strikers, and release cables for core parts return. Refer to Honda service manual. 21. Remove the left and right saddlebag taillights and sub- harnesses for core parts return . Refer to Honda service manual. 22. Remove the four m6 x 1.0 flange bolts from each saddlebag. Remove and discard the saddlebags. 23. Remove the six m6 x 1.0 flange bolts from the exhaust tips. Slide the tip off the muffler body. Save tips and bolts for reinstallation. 24. Loosen the four m8 x 1.25 SHCS on the muffler clamps. Remove the two m8 x 1.25 flange bolts. Remove and discard the mufflers and muffler gaskets. 25. Remove the four m6 x 1.0 BHCS, two rubber washers, and front fender A. 26. Remove the four m5 x .80 BHCS and chrome front fender covers. 27. 2006 & UP. 2006 & UP. 2006 & UP. 2006 & UP. Remove the Remove the Remove the Remove the two m6 x two m6 x two m6 x two m6 x 1.0 flange bolts on 1.0 flange bolts on 1.0 flange bolts on 1.0 flange bolts on rear of saddlebag/trunk stay. rear of saddlebag/trunk stay. rear of saddlebag/trunk stay. rear of saddlebag/trunk stay. 28. Unplug connector and remove amp and save for Unplug connector and remove amp and save for Unplug connector and remove amp and save for Unplug connector and remove amp and save for reinstallation. reinstallation. reinstallation. reinstallation. 29. Cut lower saddlebag supports off the saddlebag/trunk stay, where the round tubing meets the square, and cut the gusset flush, removing any burrs. See Figure 1. 30. Remove trunk stay for later use. 31. Remove the two m5 x .80 nuts on the license plate light. Remove and discard the license plate ligh

Incoming search terms:

HARLEY DAVIDSON TRI-BAR AUXILIARY RUNNING LIGHT/ BRAKE LIGHT ASSEMBLY REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 02-03-2011

download
REMOVAL 1. Remove the saddlebags and left side cover. To prevent accidental vehicle start-up, which could cause death or serious injury, remove main fuse before proceeding. (00251b) 2. Remove the main fuse. 3. See Figure 1. Remove six flange nuts (1) from the right and left fender stud plates (2). 1 2 3 5 4 is04366a 1. Nut 2. Stud plate 3. Rear fascia 4. TORX screw 5. Lamp assembly Figure 1. FLHX Rear Fascia and Lamp 4. On the left side of the motorcycle, loosen the set screw and unscrew the radio antenna mast. 5. Gently open the adhesive conduit at the split line to release the rear fascia light harness. 6. At the rear of the motorcycle, spread the top of the fascia to release from the top studs at the side of the fender and then pull the bottom in a downward direction to release the fascia from the fender. If necessary, gently wiggle the fascia while pulling. 7. 2006-2008 models only: On the left side of the motorcycle, remove the bolt (with flat washer) to remove the passenger seat strap and saddlebag front mounting bracket from the chrome frame tube cover. 8. Remove the screw and chrome frame tube cover. NOTE ALL models: Make note of the wire routing and location of all cable straps. New light wiring installs the same way. 9. See Figure 2. Release the rear fascia light wires from the wire clip (1). Cut the cable straps (2) to release the rear fascia light harness (3) and radio antenna cable. 10. 2006-2008 models: Disconnect the rear fascia light connector [12B] located inboard of the upper frame tube. 2009 and later models: Disconnect the rear fascia light connector [12B] located to the rear of the fuse panel. 11. See Figure 1. Remove the two T-20 TORX® screws to release the light assembly from the fascia. Save the screws for installation of the new light. 1 3 4 2 is04378 1. Wire clip 2. Cable strap 3. Fascia light harness 4. Flange nut Figure 2. Rear Fascia Light Harness INSTALLATION 1. Route the rear fascia light wires forward through the cable clip at the top of the radio antenna bracket and then upward in front of the saddlebag rear mounting bracket to the inboard side of the upper frame tube. 2. 2006-2008 models: On the inboard side of the upper frame tube, mate the pin and socket housings of the rear fascia light connector [12]. 2009 and later models: To the rear of the fuse panel, mate the pin and socket housings of the rear fascia light connector [12]. 3. Using the slotted hole, install a new cable strap to secure the rear fascia light wires and radio antenna cable to the rear fender support. 4. Install a new cable strap to secure the rear fascia light wires and radio antenna cable to the shoulder of the upper frame tube (just in front of the air valve mounting bracket).

Incoming search terms:

HARLEY DAVIDSON XL BRAIDED FRONT BRAKE LINE KITS INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 30-03-2011

download
REMOVAL Direct contact of D.O.T. 5 brake fluid with eyes can cause eye irritation, swelling, and redness. Avoid eye contact. In case of eye contact flush with large amounts of water and get medical attention. Swallowing large amounts of D.O.T. 5 brake fluid can cause digestive discomfort. If swallowed, obtain medical attention. Use in well ventilated area. KEEP OUT OF REACH OF CHILDREN. (00144a) Direct contact of D.O.T. 4 brake fluid with eyes can cause irritation. Avoid eye contact. In case of eye contact flush with large amounts of water and get medical attention. Swallowing large amounts of D.O.T. 4 brake fluid can cause digestive discomfort. If swallowed, obtain medical attention. Use in well ventilated area. KEEP OUT OF REACH OF CHILDREN. (00240a) D.O.T. 4 brake fluid will damage painted and body panel surfaces it comes in contact with. Always use caution and protect surfaces from spills whenever brake work is performed. Failure to comply can result in cosmetic damage. (00239b) 1. Drain the brake fluid following the instructions in the service manual. Dispose of waste properly. To prevent accidental vehicle start-up, which could cause death or serious injury, disconnect negative (-) battery cable before proceeding. (00048a) To prevent accidental vehicle start-up, which could cause death or serious injury, remove main fuse before proceeding. (00251b) 2. Disconnect the battery, negative (-) cable first or remove the main fuse. Follow the instructions in the service manual 3. Remove bolt and two sealing washers to disconnect brake line fitting from master cylinder. Discard sealing washers, but save bolt for installation. 4. Remove bolt and two sealing washers to disconnect brake line fitting from front brake caliper. Discard sealing washers, but save bolt for installation. 5. Carefully make note of brake line routing, then remove existing brake line. NOTE This kit contains clamps and cable straps to either replace the original equipment clamps and cable straps being removed or to add additional brake line support. INSTALLATION Install proper length brake lines. Incorrect brake line length can adversely affect motorcycle operation, which could cause loss of control resulting in death or serious injury. (00325a) Replace brake line gaskets. Re-using original gaskets can cause brake failure and loss of vehicle control, which could result in death or serious injury. (00318a) Avoid leakage. Be sure gaskets, banjo bolt(s) and brake line are clean and undamaged before assembly. (00323a) 1. Position new sealing washers from kit on each side of hydraulic brake fittings (banjo fittings). Small ID washers are for caliper end, large ID washers are for master cylinder end. 2. Insert bolts (removed earlier) through washers and fittings. 3. Hold new braided brake line in position and install bolts into master cylinder and caliper. Tighten only enough to keep banjo fitting in the same orientation as the stock banjo fitting. 4. Verify there is no twist in the brake line. Adjust brake line if necessary. 5. Install clamps from kit by wrapping clamp around braided brake line at each of the clamp mounting locations. Verify clamps are oriented the same as the stock clamps. Install clamp screws but do not tighten. 6. Check entire length of braided brake line: a. Be sure brake line is not twisted. b. Turn handlebars fully-left and right while checking to make sure brake line does not contact any vehicle components. c. Be sure brake line length between clamps is sufficient. 7. Adjust brake line if necessary. 8. Tighten caliper and master cylinder banjo bolts to 20-25 ft-lbs (27-34 Nm) .

Incoming search terms:

Harley-Davidson CHROME FRONT BRAKE CALIPER KIT REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 25-11-2010

download
See Figure 1. Refer to FRONT BRAKE CALIPERS: REMOVAL in the Service Manual, and follow the instructions to: a. remove the banjo bolt with bleeder valve (2) and both gaskets (4), and b. detach the front brake line (3) from the caliper. c. Discard the gaskets. For this installation, the banjo bolt (2) can also be discarded. d. Remove the caliper mounting bolts (1). Lift the brake caliper assembly upward to remove it from the brake disc. -J03529 1 of 4
2 5 3 4 1 is04104 1. Mounting bolt (2) 2. Banjo bolt with bleeder valve 3. Brake line 4. Gasket (2) 5. Screen cover Figure 1. Remove Existing Caliper 2. Remove the brake pads from the caliper. Refer to BRAKE PADS AND DISCS: BRAKE PAD REPLACEMENT, FRONT BRAKE CALIPER in the Service Manual. a. Remove the screen cover (5) from the caliper. b. See Figure 2. Note the orientation of the brake pads, and remove the retaining clip (2), pad pin (1) and brake pads from the caliper. Also note the position of the brake pads at removal, so they can be installed back in the same location. 3. Repeat the procedure for the opposite-side caliper. 2 1 is04105 1. Pad pin 2. Retaining clip Figure 2. Front Caliper Pad Pin Pad and Pin Inspection 1. Refer to BRAKE PADS AND DISCS: INSPECTION in the Service Manual, and follow the instructions given to inspect the brake pads. If any front brake pad is worn to 0.5 mm (0.020 inch) or less above the backing plate, replace all four front pads. 2. Inspect the brake disc thickness, lateral runout and warpage. If necessary, follow the instructions in the Service Manual under FRONT WHEEL to replace the discs. Chrome Caliper Installation 1. See Figure 3. Obtain the correct-side new chrome caliper assembly from the kit. Remove the screen cover (5), retaining clip and pad pin (4) from the caliper. NOTE Do not remove the shipping plug protecting the brake line threaded hole until ready to install the brake line. 2. Place the caliper over the brake disc with the brake line threaded hole (protected by a shipping plug) facing upward. 3. See Figure 1. Obtain two of the brake caliper mounting bolts (1), removed earlier. Loosely install both bolts through the front fork and into the chrome caliper. Alternately tighten the mounting bolts to 38.0-51.5 Nm (28-38 ft-lbs) . 4. Install the brake pads removed earlier or, if necessary, new brake pads into the caliper. 5. See Figure 2. Install the new pad pin (1) through the inner and outer brake pads. Tighten to 8.5-11.5 Nm (75-100 in- lbs ) . 6. Install the new retaining clip (2) onto the pad pin. NOTE Ensure that the screen cover is oriented with the single tab end up, and the double tab end down. 7. See Figure 1. Install the new screen cover (5) onto the caliper.

Incoming search terms:

Harley-Davidson Softail Conversion Kit Installation Instructions

0

Filed Under (Harley Davidson) by admin on 02-12-2010

download
1. Place the motorcycle on the lift. 2. Place a suitable Jack under the Frame of the Motorcycle and tie down securely. 3. Remove Drain Plug from Primary Cover Assembly and drain oil. 4. Slide Rubber Boot off of the Clutch Cable Adjuster. Loosen and back the Jam nut away from the Clutch Cable Adjuster. Move Clutch Cable Adjuster towards the Jam Nut to introduce free play in the Clutch Lever. 5. Remove the fasteners that secure the seat. Remove seat. 6. Disconnect negative Battery Terminal. 7. Remove the Saddle Bags. And their hardware. If equipped. 8. Loosen Muffler Clamp on both Mufflers and other attaching hardware. Remove and discard both Mufflers. 9. Loosen the 4 exhaust stud nuts and save. Remove and discard head pipes and exhaust gaskets. 10. Disconnect the Rear Lamp Wiring Harness. 11. Remove any fasteners from Electrical Box. 12. Remove and discard Rear Fender, Fender Support and fasteners. NOTE: 2008-Current various models. Remove ECM from Fender and save nuts. 13. Drain all Brake Fluid from the Rear Brake System. 14. Un-clamp Rear Brake Line from the frame and Rear Fork. 15. Remove and discard both Banjo Bolts and Crush Washers from the Rear Brake Caliper and the Rear Brake Master Cylinder. 16. Remove Brake Light Switch from the Brake line, Save for reassembly. 17. Remove the Torx screw from the Brake Line bracket, Save the Torx screw for reassembly. 18. Remove and Discard Brake Line. 19. If Lower Controls option. Remove and Discard right and left floorboards/foot pegs, brake pedal, shifter, and shift linkage. Remove and Discard Passenger Foot pegs or Floorboards and their mounts. Then skip to step 24. 20. If Lower Controls Not purchased. Continue. 21. Remove acorn nut from Shift Linkage. 22. Remove 3 fasteners from Drivers Floorboard and remove. 23. Remove and discard Jiffy Stand. 24. Remove the Primary Cover by first removing the top and rear inspection cover screws. 25. Continue by removing remaining fasteners. 14 total. 26. Remove and discard Primary Cover Gasket. 27. Clean residual gasket material from both surfaces. 28. Loosen the Top Center Nut on the Primary Chain Adjuster. Lower the Primary Chain Adjuster until it rests flat on the Inner Primary Cover. 29. Remove the Clutch Lifter Retaining Ring from the Clutch Basket. Remove Clutch Lifter Assembly. 30. Using the Primary Drive Locking Tool. Loosen the Compensating Sprocket Nut. 31. Using the Primary Drive Locking Tool. Loosen the Clutch Hub Main shaft Nut. WARNING: This nut is LEFT HAND threaded. 32. Remove the Primary Drive Locking Tool, Compensating Sprocket Nut, and Clutch Hub Main shaft Nut. 33. Remove the Sprocket cover and Sliding Cam from the Crank Shaft Extension. 34. Remove the Clutch Assembly, Primary Chain, Compensating Sprocket, and Crank Shaft Extension in one assembly.

Incoming search terms:

Yamaha V-Star 1100 Custom and Classic cruisers Floorboard/ Footpeg Extension Installation Instructions

0

Filed Under (Yamaha) by admin on 09-11-2010

download
Start on the right (brake) side. 1) Loosen the nut at the end of the brake rod. This will allow you to unscrew the brake rod from the brake lever clevis later. 2) Pull out the cotter pin and remove the pivot pin. Unscrew the clevis 3) Then using a 14mm socket or box-end wrench, remove the two bolts that hold the brake floorboard/footpeg assembly (whichever your bike has) to the frame. These bolts are torqued to 46 ft lbs, so this may be a bit difficult. 1. Loosen this nut 2. Remove the cotter pin (other side of this pivot pin) remove the pivot pin a unscrew the nut to remove the clevis nd 3. Remove these bolts When you remove the floorboard/footpeg bracket, be careful not to pull the brake switch wires loose. You may wish to cut the cable tie for more room, and then rest the bracket, with the footpeg or floorboard attached, on a short box, or block of wood, to keep it handy. Install the new brake rod, to the end of the existing brake rod. Re-install the pivot pin, and the pivot pin cotter pin. Installing the extension bar: Note that the extension bar is bolted so that it rises up in front. Use the new bolts to mount the floorboard/ footpeg bracket to the threaded holes in front. Install the Extension in the proper orientation (angled holes bolt up to the frame, with front of the bar higher than the rear – see photo) using the stock bolts for the extensions to the frame and the new bolts and washers supplied with the kit, on the forward threaded section to relocate the floorboard or footpeg bracket. The use of LocTite ® Blue here is recommended. At this point the right side Floorboard or Footpeg should be secured tightly and the brake lever hanging loose. Now install the Brake rod extension, threading the male end to the original brake rod. Don’t tighten this end yet Place the clevis over the forward most end of the brake rod extension, and threat the clevis nut onto the end of the rod. Bring the brake rod upright, to meet with the clevis at the end of the brake rod extension and replace the pivot pin. Before reinstalling the cotter pin, check the angle of the brake lever, to insure that you have the brake pedal where you want. If necessary, adjust the extension rod in or out, until you are satisfied, and then reinstall the cotter pin into the pivot pin. Check the Brake switch wire and install a new cable tie if required. Note: Due to utilizing a thicker material, 1/2″ versus 3/8″ from our competitor, the Brake rod is now positioned at a greater angle. Even with the angle, braking performance is not affected, but if you wish to bring the master cylinder in line with the brake rod, do this. Loosen the rear, and remove the front Allen bolt. Then place two washers behind the front bolt, under the bracket, and then re-install the bolts To change the angle of the brake rod, 1) loosen and remove the two master cylinder bracket Allen bolts 2) insert two washers behind the front bolt (front of the bike), behind the master cylinder bracket 3) tighten both bolts. Do not install any washers on the rear mounting hole. This will make the angle of the Brake Rod less aggressive. Step Two – Left Side For the left (Shifter) side, 1) use an open-end 10 mm wrench, to unscrew the two nuts that hold the shift rod in place. PLEASE note that one end of the shift rod has a left hand threaded nut. SAVE the nuts, as you will need them on the new longer Polished Stainless Steel Shift Rod. 2) Remove the stock shift rod. 3) Then using a 14mm socket or box-end wrench, remove the two bolts that hold the shifter floorboard/footpeg assembly (whichever your bike has) to the frame.

Incoming search terms:

2009 – Current Harley Davidson Trike Conversion Kit INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 27-02-2012

download
1. Place the motorcycle on the lift. 2. Place a suitable Jack under the Frame of the Motorcycle and tie down securely. 3. Remove Drain Plug from Primary Cover Assembly and drain oil. 4. Slide Rubber Boot off of the Clutch Cable Adjuster. Loosen and back the Jam nut away from the Clutch Cable Adjuster. Move Clutch Cable Adjuster towards the Jam Nut to introduce free play in the Clutch Lever. 5. Remove the ¼ – 20 Phillips head screw and Seat. 6. Disconnect and REMOVE battery. 7. Remove two ¼ – 20 flanged hex nuts from the Stud Plate. Remove and save the Passenger Handrail and two ¼ – 20 flanged hex head nuts if equipped. 8. Remove the Saddle Bags. 9. Remove the Right and Left Side Covers. 10. Remove Inner Tour Pak Molded Liner. 11. Disconnect the Tour Pak wiring. 12. Remove four ¼ – 20 HHCS. 13. Remove Tour Pak from Top Support Tube. 14. Remove both saddlebag support rails. 15. Loosen Muffler Clamps on both Mufflers and remove two 5/16 – 18 HHCS per Muffler. Remove and discard both Mufflers. Save Muffler Clamps. 16. Remove right side rear heat shield. 17. Remove and discard Muffler Support Plates. 18. Disconnect the Rear Lamp Wiring Harness and remove from T-stud Clip. 19. Remove four frame cover fasteners and the Left and Right Frame Covers. 20. Remove four Tour Pak Support fasteners and the Tour Pak Support.
7 21. Remove four rear fender fasteners and rear fender. 22. Remove four ½ – 13 HHCS and washers. Remove and discard Rear Air Shocks, Air lines and Air Valve bracket. 23. NOTE: NOTE: NOTE: NOTE: If motorcycle is A.B.S. Equipped refer to A.B.S. Installation Instructions. WARNING: WARNING: WARNING: WARNING: If A.B.S. Equipped DO NOT drain brake fluid. 24. Drain all Brake Fluid from the Rear Brake System. 25. Cut and remove Cable ties and un-clamp Wire Harness Loops from the Rear Brake Line along its length, including Clamps on Swing Arm. 26. Remove and discard Banjo Bolt and Crush Washers on Rear Brake Caliper. 27. Remove the Spring Clip and nut from the Rear Axle. 28. Remove Rear Axle and Rear Wheel Spacers. 29. Push Rear Wheel Assembly forward and slip Rear Belt off of the Rear Sprocket. 30. Remove Rear Brake Caliper. 31. Remove and save the two Retaining Washers from the Stud Plate. Remove and save the Stud Plate. 32. Remove Rear Wheel Assembly. 33. Remove two 3/8 – 16 SHCS. Remove Passenger Footboards.

Incoming search terms:

HARLEY DAVIDSON SOFTAIL BRAIDED REAR BRAKE LINE KIT INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 04-02-2011

download
INSTALLATION Direct contact of D.O.T. 4 brake fluid with eyes can cause irritation. Avoid eye contact. In case of eye contact flush with large amounts of water and get medical attention. Swallowing large amounts of D.O.T. 4 brake fluid can cause digestive discomfort. If swallowed, obtain medical attention. Use in well ventilated area. KEEP OUT OF REACH OF CHILDREN. (00240a) Direct contact of D.O.T. 5 brake fluid with eyes can cause eye irritation, swelling, and redness. Avoid eye contact. In case of eye contact flush with large amounts of water and get medical attention. Swallowing large amounts of D.O.T. 5 brake fluid can cause digestive discomfort. If swallowed, obtain medical attention. Use in well ventilated area. KEEP OUT OF REACH OF CHILDREN. (00144a) D.O.T. 4 brake fluid will damage painted and body panel surfaces it comes in contact with. Always use caution and protect surfaces from spills whenever brake work is performed. Failure to comply can result in cosmetic damage. (00239b) Drain Brake Fluid 1. Pop off bleeder nipple cap on the rear brake caliper. 2. Install one end of a length of plastic tubing over the caliper bleeder valve. Place the free end of the tubing into a suitable container. 3. Open the bleeder valve about 1/2-turn and pump the brake pedal to drain the brake fluid out of the rear brake system. Do not reuse brake fluid. Remove brake line components carefully. Damage to seating surfaces can cause leakage. (00320a) Remove Existing Rear Brake Line 1. Disconnect wiring harness connectors from brake light switch spade terminals. Avoid leakage. Be sure gaskets, banjo bolt(s) and brake line are clean and undamaged before assembly. (00323a) 2. Disconnect existing brake line from rear brake caliper and rear brake master cylinder assembly. Save banjo bolts, but discard brake line gaskets. NOTE This kit contains all gaskets needed for replacement. 3. Carefully make note of rear brake line routing and orientation of banjo fittings, then remove existing brake line. Save hex head screw holding brake light switch manifold to tab on frame, but discard brake line and attaching parts. 4. Unthread brake light switch from brake line. Save switch for later use.

Incoming search terms:

HARLEY DAVIDSON REAR BRAKE CALIPER KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 21-02-2011

download
INSTALLATION Prepare the Motorcycle for Service To prevent accidental vehicle start-up, which could cause death or serious injury, disconnect negative (-) battery cable before proceeding. (00048a) 1. Follow the Service Manual instructions to disconnect the negative (-) battery cable. Remove Rear Brake Caliper Remove the Brake Pads 1. For models equipped with saddlebags: Remove the right-side saddlebag. Refer to the SADDLEBAGS section of the Service Manual. 2. Remove the rear master cylinder reservoir cover. 3. Pry both the inside and outside pads away from the brake disc and toward the caliper assembly to push the caliper pistons back into their bores. Use steady pressure to prevent scoring the brake disc. Pry between the pads and the brake disc. 4. When the pistons are fully retracted into their bores, pull the pad pins out to allow the pads to drop from the caliper assembly. Note the pads’ original orientation for installa- tion. 5. Install the cover on the rear master cylinder reservoir. NOTE Place a container under the brake caliper to catch brake fluid released when removing the brake line from the caliper. 6. Remove the banjo bolt fastening the rear brake line to the stock rear brake caliper. Save the banjo bolt for brake caliper installation and discard the two steel/rubber gas- kets. Remove the Stock Rear Brake Caliper 1. Apply isopropyl alcohol to the rubber bumper on the brake caliper to ease removal. 2. Lift the stock rear brake caliper toward the front of the motorcycle. The notch in the caliper must clear the weldment on the swing arm. 3. Remove the caliper from anchor weldment on rear swingarm. Inspect Pad and Pins 1. Inspect the brake pads. If friction material above the backing plate on either pad is 0.040 in. (1.02 mm) thick or less, replace the set. Follow the instructions in the Service Manual. 2. Inspect pad pins for wear and grooving. If wear is more than 0.015 in. (0.38 mm), replace both pins. 3. Inspect the brake disc and, if necessary, follow the instructions in the Service Manual to replace the brake disc. Install the Rear Brake Caliper NOTE Pay close attention to all warnings, cautions, and torque specifications in this instruction sheet and in the service manual when installing this rear brake caliper. NOTE Apply isopropyl alcohol to the rubber bumper for ease of installation. 1. See Figure 1. Position the caliper (1) between the brake disc and the rear fork. The weldment on the fork should fit between the notch and rubber bumper on the caliper. Verify that the full length of the rubber bumper contacts the underside of the weldment

Incoming search terms:

Incoming search terms: