2009 road king solo seat springer

You search Auto repair manual PDF 2009 road king solo seat springer, if there are search results will appear below. If search results do not exist, please search by others keyword.



  2009 road king solo seat springer Direct Download speed 5282 Kb/s

  2009 road king solo seat springer Full Version speed 6162 Kb/s



HARLEY DAVIDSON ROAD KING SOLO BUCKET AND PASSENGER PILLION INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 10-02-2011

download
Installation SOLO SADDLE ONLY 1. Remove stock seat and grabstrap according to applicable Service Manual instructions. 2. Road King standard models . Remove and save the stock screws and seat mount bracket at the back of the rider solo seat. 2000 and later models . Remove the retainer washer from the stud plate and replace with two black retainer washers (2). Be careful not to allow stud plate to fall through the fender. 3. Road King standard models . Install stock solo seat mount bracket using two stock screws saved in Step 2. Road King Classic Custom models . Install solo seat mount bracket onto back of solo seat using bracket and screws included in Mount Kit Number 52903-01. 4. Install seat by sliding front of seat into seat holder bracket. Pull up on the nose of the seat to verify that the seat is securely installed. After installing seat, pull upward on front of seat to be sure it is in locked position. While riding, a loose seat can shift causing loss of control, which could result in death or serious injury. (00070a) 5. 1999 and later models . Install 1/4 in. star washers (6), spacers (4) and acorn nuts (3) onto rear mount studs. Torque to 72 in-lbs (8.13 Nm). 1998 and earlier models . Install 5/16 in. star washers (5) and 5/16-18 x 3/4 in. buttonhead screws (1) into stock mount nuts. Torque to 17 ft-lbs (23 Nm). SOLOAND PILLION 1. Remove stock seat and grabstrap according to applicable Service Manual instructions. Retain all hardware for later use. 2. Road King standard models . Remove and save the stock screws and seat mount bracket at the back of the rider seat. 3. Road King standard models. Install stock seat mount bracket onto new solo seat using two screws saved in Step 2. Road King Classic Custom models. Install solo seat mount bracket onto back of solo seat using bracket and screws included in Mount Kit Number 52903-01. 4. 1999 and later Road King standard models . Secure the rear mount bracket with stock mushroom nuts (10) and two 1/4 in. star washers (6). Torque to 72 in-lbs (8.13 Nm). 1998 and earlier Road King standard models . Install solo seat by sliding front of seat into holder bracket on bike. Secure the rear mount bracket with the two mushroom screws (11) and two 5/16 in. star washers (5). Torque to 17 ft-lbs (23 Nm). Road King Classic Custom models . Mount Kit Number 52903-01 is required for installation. Install solo seat (7) by sliding front of seat into holder bracket on bike. • 1999 and later models . Using Mount Kit Number 52903-01, secure the rear mount bracket with the two mushroom nuts (10) and two 1/4 in. star washers (6). Torque to 72 in-lbs (8.13 Nm). • 1998 and earlier models . Using Mount Kit Number 52903-01, secure the rear mount bracket with the two mushroom screws (11) and two 5/16 in. star washers (5). Torque to 17 ft-lbs (23 Nm)

Incoming search terms:

HARLEY DAVIDSON FXD SOLO SADDLE REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 21-02-2011

download
Removal of Stock Seat 1. Remove screw (6) to detach rear seat mounting bracket (9) from fender. 1996 models will have a nylon washer under the bracket that should also be saved for installation of new seat. 2. Slide seat rearward to unhook front of seat from frame, then pull seat forward out of passenger strap. 3. Remove two capscrews (10) that attach seat mounting bracket to bottom of stock seat. Install original seat mounting bracket to bottom of new solo saddle with original capscrews. Tighten capscrews securely. 4. Remove nut (7) and washer (8) that hold passenger strap (11) in place and remove strap. Installation of Kit Seat This seat is for solo driver use only. Do not attempt to carry a passenger with this solo seat installed. Use of a luggage rack, fender, or tail section as an additional seat may result in death or serious injury. NOTE When a solo seat is installed without a passenger seat, the passenger footpegs or footboards and the passenger grabstrap must be removed. For 1996 models: 1. Slide seat into position until front seat tab engages frame, then place original nylon washer under hole in rear seat mounting bracket and secure bracket to fender with screw (6). NOTE For 1997 models, a retention nut and washer must be installed into the fender hole, covered with a plastic cap, where the rear seat bracket will be attached. A cable strap is included to aid in this installation. For 1997 models: 1. Remove plastic cap from hole in fender where the rear seat bracket will be attached. 2. Place retention nut (3) over cable strap (2) so wide end of nut rests on eye of cable strap. Thread cable strap up under fender and through fender hole. Pull up on cable strap to hold nut snug against underside of fender. 3. With rib on retention nut seated into notch in fender hole, slide retention washer (4) into place from the rear. This will lock the retention nut in place. 4. Slide seat into position until front seat tab engages frame, then secure rear seat bracket to fender with screw (6). Install chrome cap (5) in rear retention nut

Incoming search terms:

HARLEY DAVIDSON XL SEAT KITS REMOVAL AND INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 29-01-2011

download
1 2 is 00911 1. Tongue 2. Keyhole Figure 2. Underside of 2-up seat INSTALLATION NOTE If installing the seat with a sissybar/backrest pad present, remove the backrest pad prior to seat installation. This will prevent damage to the pad and/or seat. Reinstall backrest pad after the seat is installed. 1. Models equipped with solo seats: See Figure 1. a. Remove the plastic plug (1) from the rear hole location in the fender (2). Save the plastic plug for installation. b. Move the seat retention nut (4) and lockwasher (5) from the middle location to the rear location, where the plug was just removed. As shown in the inset, a cable strap (6) can be used as an installation aid. Place the retention nut (5) over the cable strap so that the wide end of the nut rests on the eye of the cable strap. Thread the cable strap up under the fender, and through the fender hole. Pull up on the cable strap to hold the nut snug against the underside of the fender. c. With the rib of the retention nut (4) seated into the notch in the fender hole, slide the retension washer (5) into place from the rear. This will lock the retention nut in place. d. Reinstall the plastic plug in the fender hole in the middle location. NOTE The foam cushioning of the seat needs to be compressed as the seat is slid forward to engage the post on the frame when the seat is dropped into place. When properly installed, the front tongue on the underside of the seat should fit snugly in the groove at the fuel tank rear mounting location and the keyhole on the underside of the seat will lock the seat to the post on the frame. 2. All models: See Figure 2. a. Angle the front of the new seat into place so the tongue (1) engages the slot at the rear fuel tank mounting location. b. Push the seat forward and rotate the rear of the seat downward until the seat contacts the frame. Flex the seat slightly in the middle and slide the seat towards the rear so that the keyhole slot (2) on the seat bottom engages with the center seat post on the frame. 3. See Figure 3. Pull up on the center of the seat to verify that it is locked into place. (There will be a small amount of play, but the seat should only come up about a half an inch and then will be held firmly in place by the post on the underside of the seat.) If the seat is not firmly in place, repeat Step 2 until the seat is firmly in place. Reference the Owners Manual for further instruction on seat placement if needed

Incoming search terms:

HARLEY DAVIDSON SIGNATURE SERIES SOLO SEAT KIT REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 19-02-2011

download
REMOVAL NOTE Refer to owner’s manual or service manual for seat removal instructions for your model. 1. Remove right and left saddlebags according to the instructions in the service manual. Save saddlebag mounting brackets and hardware. 2. Remove passenger seat strap. Discard passenger seat strap. 3. Remove existing seat from vehicle. 4. See Figure 1. Remove and discard stock nuts (2) from studs (1) on rear fender (3). INSTALLATION Install Rider Seat 1. Push front seat on frame with mounting bracket at rear. 2. Firmly push front of seat downward and rearward until frame tongue engages slot in seat. 3. Push seat forward until studs are centered in slots of mounting bracket. 4. See Figure 4. Install two nuts (4) on studs to secure rear seat mounting bracket to rear fender. Alternately tighten nuts to 60-96 in-lbs (6.8-10.9 Nm). 5. If installing a new passenger seat, refer to the instructions included with the kit. After installing seat, pull upward on seat to be sure it is locked in position. While riding, a loose seat can shift causing loss of control, which could result in death or serious injury. (00070b) 6. If installing passenger seat, install passenger seat strap following the instructions in the service manual. 7. Install right and left side saddlebags following the instructions in the service manual. 1 2 3 2 1 is04121 1. Stud (2) 2. Nut (2) 3. Rear fender Figure 1. Rear Fender Install Rider Backrest NOTE Flaps shown removed for clarity of illustration. 1. See Figure 2. Turn backrest assembly (1) at a 45 degree angle clockwise to the seat. Slide the backrest shaft (2) through the flaps and into the receptacle in the seat. 2. While pushing down on the backrest assembly, twist the backrest counterclockwise until the shaft hits the stop. 3. Verify that the backrest assembly is locked in place by pulling up in the backrest pad

Incoming search terms:

HARLEY DAVIDSON DYNA CUSTOM SEAT KITS INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 15-02-2011

download
WO-UP SEAT INSTALLATION Currently Installed Seat Removal NOTE When performing the following procedures, avoid scratching painted surfaces (fender, tank, etc.) with tools or metal seat tabs. 1. Remove currently installed seat following the instructions in the Owner’s Manual. 2. If a two-up seat WAS installed: Proceed to Step 6, Grab Strap Installation . If a solo seat WAS installed: See Figure 1. Remove the Bar & Shield hole plug (11) from the rear seat mounting hole (1)Seat mounting hole, rear 2. Fender hole, center 3. Seat mounting hole, front 4. Grab strap mounting hole 5. Wire routing hole (reference) 6. Fender hole, front (reference) 7. Hardware location for two-up seat 8. Hardware location for solo seat 9. Seat retention nut 10. Retention washer 11. Hole plug, Bar & Shield 12. Hole plug, plain Figure 1. Fender Hole Identification and Hardware Locations 3. At the front seat mounting hole (3), remove the retention washer (10) from the seat retention nut (9). From the underside of the fender, remove the seat retention nut from the vehicle. Insert the Bar & Shield hole plug into the front seat mounting hole. 4. See Figure 2. Obtain the cable strap (3) from the kit. a. Place the retention nut (1) over the cable strap (3) so that the wide end of the nut rests on the eye of the cable strap. b. Thread the cable strap up under the fender and through the rearmost seat mounting hole. c. Pull up on the cable strap to hold the nut snug against the underside of the fender. d. With the rib on the retention nut seated into the notch in the fender hole, slide the retention washer (2) into place from the rear (this will lock the retention nut in place), then remove the cable strap. 3 2 1 is01955 1. Retention nut 2. Retention washer 3. Cable strap (installation aid) Figure 2. Retention Nut Installation Grab Strap Installation 5. If a two-up seat WAS installed: Remove the existing grab strap and all attaching hardware, then proceed to Step 6. If a solo seat WAS installed: Proceed to Step 6. 6. See Figure 5. Obtain the new grab strap (8), hex head screw (9), plastic retention nut (10), washer (11) and hex nut (12) from the kit. 7. From the underside of the fender, insert the screw up through the grab strap mounting hole and secure with the plastic retention nut.

Incoming search terms:

HARLEY DAVIDSON BADLANDER SEAT KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 18-04-2011

download
Installation When performing the following procedures, be careful not to scratch painted surfaces (fender, tank, etc.) with metal tabs on seat. 1. Remove existing seat strap from motorcycle. Retain all hardware. Discard seat strap. 2. Remove existing seat from motorcycle by removing Phillips head screw with lockwasher, and nylon washer from rear fender mounting bracket. Retain all hardware except discard nylon washer. 3. Disengage seat from frame tab at front of seat. 4. Install new seat onto motorcycle, making sure bracket on front of seat fully engages into seat mounting tab on frame. NOTE On rear fenders of 1997-1999 models, a captive nut secured with a plastic retention washer has replaced the previously used weld nut. Do not remove the plastic retention washer unless the captive nut is damaged and must be replaced. The plastic retention washer also prevents seat bracket from contacting paint on fender. Therefore, no nylon washer is required between bracket and fender on 1997-1999 models. 5. On pre- 1997 models , secure seat onto rear fender with original screw and lockwasher and place guide washer (1) between seat bracket and rear fender. 5a. On 1997-1999 models , secure seat onto rear fender with original screw and lockwasher. After installing seat, pull upward on front of seat to be sure it is locked in position. If seat is loose, it could shift during vehicle operation, resulting in loss of control of vehicle and death or serious injury. 6. Use original hardware to install new seat strap (2) in same location as old seat strap. On FXSTC, Softail Custom models, fasten seat strap to fender support

HARLEY DAVIDSON DYNA ACCESSORY SEAT KITS INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 29-01-2011

download
For vehicles with 2-up seating 1. Remove the existing seat from motorcycle. Save the mounting screw for installation of the new seat. 2. Remove existing grab strap and all attaching hardware. 3. See Figure 1 for information on which holes to install grab strap through for your seat (use the hole shown dark in the illustration). Install new grab strap onto motorcycle at same location old grab strap was removed (re-use existing hardware). Tighten to 60-90 in-lbs (6.78-10.17 Nm) . 4. Position new seat on motorcycle. Be sure tongue on front of seat fully engages into the seat mounting slot between the gas tank bracket and frame. 5. Secure seat with stock screw. After installing seat, pull upward on seat to be sure it is locked in position. While riding, a loose seat can shift causing loss of control, which could result in death or serious injury. (00070b) Kit Number: 52284-06 and 52359-06 Kit Number: 52159-06 Kit Number: 51540-06 Kit Number: 52288-06 Kit Number: 51471-06 and 51472-06 Grab StrapNumber: 52370-04 Grab StrapNumber: 51176-96B Grab StrapNumber: 51173-93 Grab StrapNumber: 51176-96B Grab StrapNumber: 51173-93 Kit Number52378-07 Grab StrapNumber: 52313-96 is03552a Figure 1. Grab Strap installment information For vehicles with solo seat 1. Remove the existing seat from the motorcycle. Save the mounting screw for installation of the new seat. 2. See Figure 2. Remove the plastic cap from the rear most fender hole (3). 3. Remove the seat retention nut and washer from the solo seat mounting hole

HARLEY DAVIDSON XL SOLO CUSTOM SEAT KITS INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 02-03-2011

download
INSTALLATION 1. Refer to the Owner’s Manual and follow the instructions given to remove the seat. 1 2 4 1 3 is03341 1. Stock retention nut and washer 2. Plastic cap 3. Rearward fender hole 4. Center fender hole Figure 1. Retention Nut and Plastic Cap Location 2. For models that had a solo seat: Proceed to Step 3. For models that had a 2-up seat: The retention nut and washer must be moved from the rearward mounting hole to the center fender hole where the rear seat bracket will be attached. Use a cable strap to aid in this step as fol- lows: a. See Figure 1. Remove retention nut from rearward fender hole (3) and plastic cap (2) from center fender hole (4). b. Install plastic cap into the rearward fender hole. c. See Figure 2. Place the retention nut over the cable strap so the wide end of the nut rests on the eye of the cable strap. Thread the cable strap up under the fender and through the center fender hole. Pull up on the cable strap to hold the nut snug against the underside of the fender. d. With the rib of the retention nut seated into the notch in the fender hole, slide the retention washer into place from the rear. This will lock the retention nut in place. 3. Position the solo seat on the motorcycle frame with the mounting bracket at the rear. Bring the seat forward and engage the tab on the seat into the slot at the base of the fuel tank. 4. See Figure 3. Secure the seat to the fender using the knurled knob (3) and neoprene washer (4) from the kit. Install the washer on the knob and tighten the knob securely to the fender seat nut

HARLEY DAVIDSON CHROME SEAT POST REMOVAL AND INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 11-02-2011

download
REMOVE 2 1 is00000 1. Seat Post 2. Screw Figure 2. Lower Seat Post 1. Refer to Owners Manual to remove the seat. To prevent accidental vehicle start-up, which could cause death or serious injury, disconnect negative (-) battery cable before proceeding. (00048a) 2. Disconnect battery negative cable. 3. On motorcycles equipped with oxygen sensors, disconnect the rear sensor connector. 4. See Figure 2. Remove screw (2) and washer from the lower seat post (1) and discard. -J04294 1 of 2 5. Disconnect spark plug wires and primary wire from ignition coil. 6. See Figure 3. Loosen the bracket screws (1). Remove seat post screw (2) and seat post with ignition coil and cover. 7. See Figure 4. Remove coil cover screw (5) and cover (4) from stock seat post (1). 8. Remove ignition coil screws (3) and coil (2) from seat post. 2 1 is04241 1. Bracket Screws 2. Upper Seat Post Screw Figure 3. Upper Seat Post Fasteners 2 5 1 3 4 is04337 1. Seat Post 2. Ignition Coil 3. Coil Screw 4. Coil Cover 5. Coil Cover Screw Figure 4. Install Ignition Coil to Seat Post INSTALL 1. See Figure 4. Install ignition coil (2) to new seat post using screws (3). Tighten ignition coil screws to 10-15 ft-lbs (13.6-20.3 Nm) . 2. Install coil cover (4) to seat post with screw (5) and tighten to 30-40 in-lbs (3.4-4.5 Nm) . 3. See Figure 1. Place seat post (1) in position and attach lower post with screw (2), washers (3) and dome nut (4). Tighten screw (2) to 10-15 ft-lbs (13.6-20.3 Nm) . 4. See Figure 3. Attach upper seat post with screw (2). Tighten screw (2) to 12-15 ft-lbs (16.2-20.3 Nm) . Tighten bracket screws (1) to 12-15 (16.2-20.3 Nm) . 5. Connect primary wire to ignition coil. 6. Connect spark plug wires to ignition coil. The rear cylinder plug wire attaches to the top coil post. Ensure that spark plug wire boots are fastened securely. 7. Connect rear oxygen sensor connector, if equipped. 8. Reconnect battery negative cable

Incoming search terms:

Harley- Davidson FX/ FL Big Twin 1965-1984 Two-Piece Seat Mounting Suggestions

0

Filed Under (Harley Davidson) by admin on 15-04-2012

download
Stock One-Piece Seat Removal Steps 1. Remove rear fender screw located behind the passenger seat and set aside. The stock rear fender screw will be used to attach your new Mustang Two-Piece Seat. 2. Slide seat back and up. Mounting of Mustang Solo & Passenger Seat 1. Remove two screws from back of Mustang solo seat. 2. Align two chrome tabs located at the front of the passenger seat with the mounting holes in back of solo. 3. Screw rear seat and solo together. 4. Slide solo front forks under frame. 5. Align chrome rear tab located at back of passenger seat with stock hole in fender. 6. Secure in place with stock fender screw to complete the installation process. Note: Use of side brackets optional and would use the rubber expansion plugs, threaded inserts, and bolts used for a solo only installation.

Incoming search terms:

Incoming search terms: