2010 ktm 50sx carb schematic

You search Auto repair manual PDF 2010 ktm 50sx carb schematic, if there are search results will appear below. If search results do not exist, please search by others keyword.



  2010 ktm 50sx carb schematic Direct Download speed 5282 Kb/s

  2010 ktm 50sx carb schematic Full Version speed 6162 Kb/s



KAWASAKI 1500 CARB THUNDER Air Filter Kit Installation And removal Instruction

0

Filed Under (Kawasaki) by admin on 25-10-2010

download
1) Remove Seat 10mm KAW 1500 CARB ADPTOR QTY PARTS LIST 1 1500 CARB ADAPTOR 1 3″ PIECE OF HOSE 1 DOUBLE BARB 1 L-BARB 1 3/8″ RED PLUG 1 ¼” BLACK VACCUM PLUG 1 M6-1 NYLON INSERT LOCK NUT 3 M6-1 X 16 FLAT SOCKET HD CAP SCREW 1 170 MJ 1 INSTRUCTIONS 2) Remove Dash Plaque 8mm bottom Bolt only 3) Lift from bottom then Remove speedo cable 4) Disconnect Electric Plugs 5) Remove 12mm bolts holding tank 6) Turn petcock OFF – Pinch off fuel line. 7) Disconnect the electric Plug under speedo opening 8) Lift Tank at Rear – Disconnect two Vent Lines; Fuel gage Vent will Pull up – Remove. 9) Remove Chrome Air Cover. 10) Left side Remove two screws – 10mm bolt in side Air box. Pull hoses off Remove 1″ hose going to cross over Tube. 11) Remove two 8mm bolts on Bracket – Remove Bracket 12) Remove Screw on Top of air Box Snorkel 13) Remove both side covers 14) Remove air Backing plate right side (Crank Case Breather hose that connects to stock air box will connect to new) 15) Remove Bracket that holds Carb and holds Backing Plate 16) Take idle adjustable Knob loose – let hang loose 17) Take Choke Knob out of holding Bracket 18) Hose that went to cross over tube MAY BE PLUGGED OR VENTED your Choice (Fresh air unit) ** 98′S or any models with carb warmer should disconnect carb warmer by pinching off line on each side of connector that plugs into carb on bottom. Small bracket with one screw directly on the bottom of carb. 19) Loosen Clamp that holds Carb to intake Manifold, Carb will hang loose 20) Remove intake Manifold 5mm Allen- Remove crossover tube. 21) (- BE CAREFULL-) LINE IT UP RIGHT- Replace intake Manifold (YOU MAY TO SEAL THIS WITH A SEALER LIKE PERMATEX) ( BE SUPER CAREFUL TO KEEP INTAKE COVERED DURING EACH STEP. SCREWS CAN FALL ONTO INTAKE) 22) Drain Float Bowl 3mm allen – very bottom of carb 23) Remove Float Bowl 4 screws (#2 Phillips) let hang down 24) Remove main jet, if Emulsion tube comes out use 8mm and Flat tip to separate jet from Emulsion tube. 25) Install with new jet 26) CAREFULLY Reinstall Float Bowl Cover 27) If installing Needle Remove Top Cover of Carb, Carefully pull the slide out. ( BE CAREFUL WITH DIAPHRAM) Remove Spring + Needle Install new Needle (WE RECOMMEND THE 3RD CLIP FROM TOP WITH TWO WASHERS ON TOP. REINSTALL 28) Be sure to reseat diaphragm – BE CAREFUL Reinstall Cover. 29) Install Carb to Intake – reconnect carb warmer if applicable 30) Reattach idle adjustment 31) Reattach Choke 32) Reattach Bracket in front of Carb- 33) Take Center bolt mount Rubber Gromlet from Stock Air box Plate install in to new Air box Adapter use stock Bolt, Attach to Bracke

Incoming search terms:

HW Prowler Carburetor Installation Instructions

0

Filed Under (Mikuni) by admin on 31-10-2010

download
1. Remove both seats and the plastic seat pans under the seats. 2. Remove the engine cover 3. Remove the air-box by removing the cross-bar support that runs under the air-box to the framing on each side by the seat framing and disconnect the air box from the carburetor and from the plastic intake in the rear. 4. Disconnect the engine breather hose from the bottom of the air box 5. Set the air-box to the side 6. Disconnect the plug going to the stock carburetor, this is the electronic choke. Wrap the end left on the vehicle with electrical tape. 7. Cut the fuel line just above the fitting on the passenger side of the carb 8. Remove the side cover off the drivers side of the carb where the throttle cable goes in, see fig. #1 9. Pull the throttle cable out and then remove the throttle cable end from the throttle plate See Fig. #2 10. Loosen the clamp on the rear of the carb holding the carb on 11. Pull the carb out of the intake boot 12. Set OE carb to the side. 13. Push the new Carb into the intake boot making sure the carb is perfectly vertical and then tighten the clamp back up. The new carb is slightly larger than the stock one so some additional pressure will be needed to get it in. 14. Route all the breather lines connected to the carb down under the carb. 15. Connect the throttle cable onto the new carb but putting the cable end in the bottom hole of the throttle plate on the passenger side of the carb allowing the cable to ride in the slot in the plate and then turn the throttle plate clock wise allowing the threaded end of the cable to fit into the lower round hole of the throttle cable connection plate. See Fig. #3 16. Make sure you have a nut on each side of the plate turn the nut on the outside of the plate to take up the slack in the throttle cable then tighten the nut on the inside of the plate. See Fig. #3 17. Push the fuel line onto the fuel inlet on the passenger side of the carb and install the supplied clamp to hold it on. The fuel line will be a little hard to push on. 18. DO NOT ATTEMPT TO INSTALL THE CHOKE CABLE PARTS SUPPLIED IN THE KIT UNTIL AFTER THE CHOKE CABLE ITSELF IS INSTALLED AND READY TO SCREW INTO THE CARBUETOR. 19. To install the supplied choke cable, drill a 3/8″ hole in the dash on the left side of the steering wheel in a location convenient to your left hand. 20. Remove the plastic nut from the bottom of the choke handle on the choke cable. 21. Push the choke cable thru the hole you drilled and then slide the nut over the cable to the inside of the dash and reinstall back on the back of the choke mechanism. Some dash screws maybe needed to be removed to accomplish this

42MM MIKUNI FLATSLIDE CARBURETOR INSTRUCTIONS

0

Filed Under (Mikuni) by admin on 31-10-2010

download
To install, remove the stock carb per Yamaha shop manual procedures. Remove stock throttle cables. Install Mikuni HSR carb into intake manifold and tighten manifold clamp. Install new HSR series throttle cables and adjust cable slack per Yamaha shop manual procedures. Hook fuel line to HSR carb and fasten clamp.* Start motorcycle and fine tune HSR carb for proper running per supplied Mikuni tuning manual. *NOTE: Mikuni HSR series carburetors are designed for gravity-feed fuel systems. You should bypass your stock fuel pump and directly feed your HSR carb right from the fuel petcock. We have noted, though, that you may not be able to get good fuel flow from your Road Star fuel tank in low-fuel situations. You may run your stock fuel pump with the HSR carb, but to do so requires the purchase and installation of an adjustable fuel pressure regulator (set at 1/2 to 1 lb. of pressure). These are available from most auto parts stores. The stock carb has 2 wires running to the lower rear of the float bowl , these were for a carb warmer, they are not used in this application. Unplug these wires at the main wire harness and retain with your stock carb. The Road Star ignition system uses data from the stock throttle position sensor (TPS) to manage your ignition timing. It is necessary to give the bike this information. You may do so by removing the TPS sensor from the stock carb, leaving it plugged into the main wire harness (the sensor must be fixed to a closed-throttle position), or you may locate the plug for the TPS on the main wire harness and test the leads – you will find one ground, one with .5V and one with 1.5V. Connect the 1.5V to the ground and this will give the bike the same information as stock fully closed throttle. The output of the OEM fuel pump is too high and will cause fuel overflow in the HSR carb, resulting in a possible dangerous fire hazard

Incoming search terms:

Mikuni HSR 42/ 45 Installation Instructions

0

Filed Under (Mikuni) by admin on 31-10-2010

download
To install, remove the stock carb per Yamaha shop manual procedures. Remove stock throttle cables. Install Mikuni HSR carb into intake manifold and tighten manifold clamp. Install new HSR series throttle cables and adjust cable slack per Yamaha shop manual procedures. Hook fuel line to HSR carb and fasten clamp.* Start motorcycle and fine tune HSR carb for proper running per supplied Mikuni tuning manual. *NOTE: Mikuni HSR series carburetors are designed for gravity-feed fuel systems. You should bypass your stock fuel pump and directly feed your HSR carb right from the fuel petcock. We have noted, though, that you may not be able to get good fuel flow from your Road Star fuel tank in low-fuel situations. You may run your stock fuel pump with the HSR carb, but to do so requires the purchase and installation of an adjustable fuel pressure regulator (set at ½ to 1 lb. of pressure). These are available from most auto parts stores. The stock carb has 2 wires running to the lower rear of the float bowl , these were for a carb warmer, they are not used in this application. Unplug these wires at the main wire harness and retain with your stock carb. The Road Star ignition system uses data from the stock throttle position sensor (TPS) to manage your ignition timing. It is necessary to give the bike this information. You may do so by removing the TPS sensor from the stock carb, leaving it plugged into the main wire harness (the sensor must be fixed to a closed-throttle position), or you may locate the plug for the TPS on the main wire harness and test the leads – you will find one ground, one with .5V and one with 1.5V. Connect the 1.5V to the ground and this will give the bike the same information as stock fully closed throttle.

2010 Harley-Davidson New Model and Technical Information

0

Filed Under (Harley Davidson) by admin on 15-12-2010

download
Meet MY2010 EPA Emissions regulations for all Harley- Davidson®vehicles sold in 50 state and Canadian markets •Reduce oxygen intrusion into the exhaust system -Promotes catalyst health and efficiency New rib/curl pipe end feature offers positive muffler stop and improved pipe consistency. 2010 Dyna®Models Crossover joints updated with new clamp and gasket. Updated joint New clamp (Comes w/gasket) New Gasket Torque 15-19 ft-lbs (20.3-25.8 Nm) 2010 Dyna®Models New 2010 FXDWG Wide Glide® New 2010 FXDWG Wide Glide® New rear fender New Floating Front Brake Rotors* New fuel tank with wider tunnel* *All Dyna®Models Current FXDB solo seat with new cover New sissybar New pillion Current FXDWG front forks with 1″shorter overall length Current FXDWG front wheel (steel) (21×2.15) black rim with chrome spokes & machined hub; Front tire pattern -GT402 FXDWG front fender 34 degree frame with tank mount boss raised by ¾” New handlebar with FXDF risers/caps *Michelin®tires on all but FXDF and FXDWG FXDB rear wheel (black rim with chrome spokes) (17×4.5) (180- 60×17), rear tire pattern -GT502 (Screamin’Eagle®) FXDF exhaust pipes & mufflers with chrome exhaust shields Gloss black rear forging covers Current FXDB rear shocks with top covers Current FXDC battery cover with chrome Wide Glide®trim Forward foot controls New 2010 FXDWG Wide Glide® Domestic tail lights Canada & all International tail lights Taillight (HDI/Canada) Side mount license plate Domestic only •Internally wired handlebar •34 degree frame with tank mount boss raised by ¾”& rear forgings moved out 2mm each side from FXDF •Flame tank replacement part is VIN restricted •Two new rear fenders (Domestic & HDI/Canada)

Incoming search terms:

Toyota 2007- 2010 Camry 2009- 2010 Venza INSTALLATION INSTRUCTIONS

0

Filed Under (Toyota Manuals) by admin on 25-09-2011

download
Turn the ignition OFF and disconnect the vehi- cle’s negative battery cable Disconnect the mass sensor electrical connection by depressing the center tab and gently pulling the harness away from the mass air sensor. Release the
two wiring harness clips from the air box lid ently pull the engine cover upward to release it from the mounting grommets. Once released, Re- move engine cover from the vehicle and set aside. 4. Disconnect the vacuum line from the intake mani- fold plenum connection. 5. Disconnect the vacuum line from the upper air box lid. Toyota
2007-10 Camry 2009-10 Venza V6-3.5L 69-8611 7. Disconnect the two vacuum lines from the “Vacuum switching valve.

Incoming search terms:

2000-2010 KTM X2 SWITCH WIRING HARNESS Removal and Installation Manual

0

Filed Under (KTM) by admin on 25-01-2012

download
The included 3600-SWHA switch harness is intended for use with offroad models that do not come with a Hi/Low beam switch from the factory. The harness is compatable with stock AC lighting electrical systems as well as high output DC electrical systems. 1. Remove the stock numberplate or headlight. Remove the stock kill switch from handlebars and replace with the 3600-SWHA switch. 2. Remove the gas tank. Route the white and black leads from the 3600-SWHA under the tank following the wires from the stock kill switch. Disconnect the stock kill switch bullet and connect the white wire of the 3600-SWHA to the wiring harness. Disconnect the stock kill switch ring terminal and connect the ring terminal of the 3600-SWHA. Fully remove the stock kill switch. Be sure all the wires are safe from being burned or pinched and re-install the gas tank. 3. Disconnect the two female spade terminals from the stock headlight switch (if present). Connect the terminal with the yellow wire to the red power lead from the switch. Connect the white wire to the blue accessory output from the switch. Be sure the clear silicone sleeves are covering the stock plastic housings. 4. Connect the X2 headlight to the switch headlight plug. Note: The stock headlight plug will not be used for the X2 installation, but is still functional for connecting the stock headlight. The stock plug will turn on and off with the new headlight switch, and will be powered in either of the Low or High Beam positions

KTM 2010 50 SX 50 SXMini OWNER'S MANUAL

0

Filed Under (KTM) by admin on 03-02-2012

download
To give your child a feel for the brake, you should push your child at first. Do not start the engine until your child can is able to apply the necessary brake pressure. At the start, let your child ride to another person who can help him or her stop and turn. -Erect obstacles for your child to navigate around to accustom your child to handling the vehicle. -Yourchildshould also try to ride as slowly as possible and in a standing position to geta better feeling for the vehicle. -Donotletyour child try any off-road rides that would exceed the ability and experience of your child. -Yourchildshould hold the handlebar firmly with both hands and keep his or her feet on the footrests when riding. -Donotexceedthe maximum allowable rider weight. Guideline Maximum rider weight <35 kg (<77 lb.) Maximum rider size Checkthegearoil level. (p. 57) (50 SXMini) -Checktheoillevel. (p. 55) -Checkthechain tension. (p. 34) -Checkthechain dirt accumulation. (p. 33) -Checkthetire condition. (p. 47) -Checkthetireair pressure. (p. 47) -Checkthefront brake fluid level. (p. 37) -Checktherear brake fluid level. (p. 42) -Checkthefront brake linings. (p. 39) -Checktherear brake linings. (p. 43) -Checkthefunction of the brake system. -Checkthecoolant level. (p. 49) -Checkthesettings of all controls and ensure that they can be operated smoothly. -Checkthe functioning of the electrical equipment. Starting Danger Danger of poisoning  Exhaust gases are poisonous and can result in unconsciousness and/or death. -When running the engine, always make sure there is sufficient ventilation, and do not start or run the engine in a closed space without an effective exhaust extraction system. Note Engine failure  High engine speeds in cold engines have a negative effect on the service life of the engine. -Always warmup the engine at low engine speeds. Info If the motorcycle is unwilling to start, the cause can be old fuel in the float chamber. The flammable elements of the fuel evaporate after along time of standing. If the float chamber is filled with fresh fuel, the engine starts immediately.

KTM 2010 450 EXCUSA 530 EXCUSA INSTALLATION MANUAL

0

Filed Under (KTM) by admin on 03-02-2012

download
Clutch lever 500133-10 The clutch lever  is fitted on the left side of the handlebar. The clutch is hydraulically operated and self-adjusting. Hand brake lever 400196-10 Hand brake lever  is located on the right side of the handlebar. The hand brake lever is used to activate the front brake. EmergencyOFFswitch 500144-10 The emergency OFF switch  is fitted on the left side of the handlebar. Possible states Ignition off-In this position, the ignition circuit is interrupted, a run- ningenginestops, and anon-running engine will not start. Ignition on-In this position, the ignition circuit is closed, and the engine can be started. Ignition switch 300396-10 The ignition switch  is on the right behind the headlight mask. Possible states Ignition off-In this position, the ignition circuit is interrupted, a run- ningenginestops, and anon-running engine will not start. Ignition on-In this position, the ignition circuit is closed, and the engine can be started. Electrics tarter button 500144-12 Electric starter button  is fitted on the right side of the handlebar. Possible states •Electric starter button is in home position •Electric starter button is pressed-In this position, the electric starter is actu

KTM KINETO TRACKING MOUNT – MODEL K433 Installation and Removal Manual

0

Filed Under (KTM) by admin on 30-01-2012

download
the KTM meets the needs of a wide variety of test range and scientific applications:  On-board operator, or remote analog or digital control  Payloads up to 1200 pounds (unmanned) or 600 pounds (manned)  Mission configuration with four (manned) or six (unmanned) payload positions  Complete turnkey systems available  Detailed installation documentation FIELD-PROVEN RUGGED AND RELIABLE The KTM consistently demonstrates its performance and durability:  Weather tight seals designed to withstand harsh range environments  The KTM’s direct drive axis design delivers smooth, jitterfree tracking to ensure precise Time, Space and Position Information (TSPI)  Self-contained and trailer-mounted, the KTM is quickly and easily deployed via highway and unimproved roads to remote tracking sites  Digital Control System (DCS) that guarentees system reliability WHEN THE RANGES REQUIRED PRECISE AND RELIABLE OPTICAL TRACKING MOUNTS, THEY SELECTED THE BRASHEAR KINETO TRACKING MOUNT MORE THAN 150 TIMES. Recognized Standard for Tracking Systems Worldwide THE KTM DIGITAL CONTROL SYSTEM (DCS) INCLUDES:  High speed communication via an Ethernet interface to provide remote operation  Advanced servo loop control to optimize tracking performance  Built-in error correction to ensure precision tracking accuracy  Versatile chassis architecture that accommodates additional PC104 cards suchas an “Automatic Video Tracker” (AVT) to satisfy specific customer requirements and missions

Incoming search terms:

Incoming search terms: