2010 road glide repairable

You search Auto repair manual PDF 2010 road glide repairable, if there are search results will appear below. If search results do not exist, please search by others keyword.



  2010 road glide repairable Direct Download speed 5282 Kb/s

  2010 road glide repairable Full Version speed 6162 Kb/s



Harley Davidson FL series Electra Glide, Ultra Classic, Road King, Road Glide Left and Right Mounting Plate Installation Installation Manual

0

Filed Under (Harley Davidson) by admin on 25-02-2012

download
Remove existing control arm end cap and grind the outside flush. See picture below for reference. The swing arm will drop if both sides are removed at the same time. To ease installation, complete one side before starting on the other. Note: there is a left and right. Left and right end caps shown. 2. Install mounting plate assembly 10002351 on top of the end cap using 7/16″ hex head bolt and lock washer in the bottom hole. Use the 7/16″ counter sink bolt in the top hole. Make sure the end cap is seated properly. The end cap notch should fit into the recess on the frame. The pivot arm assembly is shipped on mounting plate assembly; you may remove the pivot arm to make installation easier. 3. Snug up the bolts evenly, make sure the end caps are not crooked in relation to the frame. Tighten both bolts to 25 ft lbs. (Further tightening will be required after the toe in is set). 4. If you removed the left hand pivot arm assembly, remount it now, 10002575-A (pg 20) with seal, bearings (2), washer, nut, cotter pin and dust cover. 5. Repeat for right hand side. 5 Toe In Adjustment Adjustment made with the mounting plates, bolts, pivot arms, and hubs (without wheels and tires) in place

Incoming search terms:

HARLEY DAVIDSON ROAD KING SOLO BUCKET AND PASSENGER PILLION INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 10-02-2011

download
Installation SOLO SADDLE ONLY 1. Remove stock seat and grabstrap according to applicable Service Manual instructions. 2. Road King standard models . Remove and save the stock screws and seat mount bracket at the back of the rider solo seat. 2000 and later models . Remove the retainer washer from the stud plate and replace with two black retainer washers (2). Be careful not to allow stud plate to fall through the fender. 3. Road King standard models . Install stock solo seat mount bracket using two stock screws saved in Step 2. Road King Classic Custom models . Install solo seat mount bracket onto back of solo seat using bracket and screws included in Mount Kit Number 52903-01. 4. Install seat by sliding front of seat into seat holder bracket. Pull up on the nose of the seat to verify that the seat is securely installed. After installing seat, pull upward on front of seat to be sure it is in locked position. While riding, a loose seat can shift causing loss of control, which could result in death or serious injury. (00070a) 5. 1999 and later models . Install 1/4 in. star washers (6), spacers (4) and acorn nuts (3) onto rear mount studs. Torque to 72 in-lbs (8.13 Nm). 1998 and earlier models . Install 5/16 in. star washers (5) and 5/16-18 x 3/4 in. buttonhead screws (1) into stock mount nuts. Torque to 17 ft-lbs (23 Nm). SOLOAND PILLION 1. Remove stock seat and grabstrap according to applicable Service Manual instructions. Retain all hardware for later use. 2. Road King standard models . Remove and save the stock screws and seat mount bracket at the back of the rider seat. 3. Road King standard models. Install stock seat mount bracket onto new solo seat using two screws saved in Step 2. Road King Classic Custom models. Install solo seat mount bracket onto back of solo seat using bracket and screws included in Mount Kit Number 52903-01. 4. 1999 and later Road King standard models . Secure the rear mount bracket with stock mushroom nuts (10) and two 1/4 in. star washers (6). Torque to 72 in-lbs (8.13 Nm). 1998 and earlier Road King standard models . Install solo seat by sliding front of seat into holder bracket on bike. Secure the rear mount bracket with the two mushroom screws (11) and two 5/16 in. star washers (5). Torque to 17 ft-lbs (23 Nm). Road King Classic Custom models . Mount Kit Number 52903-01 is required for installation. Install solo seat (7) by sliding front of seat into holder bracket on bike. • 1999 and later models . Using Mount Kit Number 52903-01, secure the rear mount bracket with the two mushroom nuts (10) and two 1/4 in. star washers (6). Torque to 72 in-lbs (8.13 Nm). • 1998 and earlier models . Using Mount Kit Number 52903-01, secure the rear mount bracket with the two mushroom screws (11) and two 5/16 in. star washers (5). Torque to 17 ft-lbs (23 Nm)

Incoming search terms:

2010 Harley-Davidson FLHR Road King front and rear 4-piston braking system Installation

0

Filed Under (Harley Davidson) by admin on 31-10-2010

download
in Vivid Black with blue and silver pinstripes, six-speed. Air-cooled, Twin Cam 96™ engine with Electronic Sequential Port Fuel Injection (ESPFI), ABS, security system, cast wheels with independent front and rear 4-piston braking system. Motorcycle generously donated by Harley-Davidson Motor Company Police & Fleet Sales. MSRP excludes all taxes title/documentary fees, registration, tags, dealer prep, labor and installation charges, insurance, optional equipment and accessories, certificate of compliance or non-compliance fees, and finance charges. Delivery must be coordinated through Rockville Harley-Davidson by November 30, 2010. Winner is responsible for any applicable fees above. 6,000 tickets printed. Odds of winning are 1:6,000. Ticket holder need not be present to win. Licensed by the D.C. Lottery and Charitable Games Control Board. Must be 18 years or older to win. No substitutes, return for cash, or other models. As per IRS tax code, amounts paid for chances in a raffle do not qualify as a deductible charitable contribution. Taxes on prizes are the responsibility of the winner. Harley-Davidson is proud to be a sponsor of the National Law Enforcement Officers Memorial Fund. Harley-Davidson Motor Company is a prize provider only, and Harley-Davidson, Inc., and Harley-Davidson Motor Company have no responsibility regarding conduct or administration of the raffle.

Incoming search terms:

HARLEY DAVIDSON BLACK ENGINE GUARD KIT REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 24-02-2011

download
REMOVAL NOTE This Instruction Sheet covers several different Harley-Davidson models and years. Be sure to locate and follow the procedures that apply to the motorcycle receiving the new guard. For Models without Lower Fairings 1. Proceed to For All Models section. For Model FLHTCUI (Ultra Classic Electra Glide) with Factory-Installed Lower Fairings 1. Remove the lower fairings following the instructions in the appropriate Service Manual. 2. When the lower fairings have been removed, proceed to For All Models section. For Models FLHR/I (Road King), FLHT (Electra Glide Standard) or FLHTC/I (Electra Glide Classic) with Harley-Davidson Genuine Motor Accessory Lower Fairings 1. See Figure 1. Remove the two black screws (1) that attach the fairing cap (2) to the lower fairing (5). Remove the cap. Set the parts aside for re-installation. 2. Remove the screw (7), rubber washer (8) and locknut (10) and the clamp (9) that attaches the bottom of the lower fairing to the engine guard and set aside. 3. Remove the two locknuts (3), U-bolt (6) and U-bolt retainer (4). 4. Remove the lower fairing by sliding it out from behind the engine guard. 5. Repeat Steps 1 through 4 for the opposite side. 6. Proceed to For All Models section. For Model FLTR/I (Road Glide) with Harley-Davidson Genuine Motor Accessory Lower Fairings Disconnect negative (-) battery cable first. If positive (+) cable should contact ground with negative (-) cable connected, the resulting sparks can cause a battery explosion, which could result in death or serious injury. (00049a) 1. Disconnect the battery, negative (-) battery cable first, following the instructions in the appropriate Service Manual. 2. Remove the seat following the instructions in the appropriate Service Manual. 3. Remove the cable strap holding the clutch cable to the engine guard. 4. See Figure 2. Remove the TORX screw (8), rubber washer (9) and locknut (11) and the clamp (10) that attaches the bottom of the lower fairing (4) to the engine guard and set aside INSTALLATION 1. Hold the engine guard in position, and loosely fasten the top of the guard with the new hex socket screw and flat washer from the kit. 2. Install the bottom brackets to the motorcycle frame with the two new TORX screws and locknuts. 3. Tighten all three screws to 15-20 ft-lbs (20.3-27.1 Nm) . For Model FLHTCUI (Ultra Classic Electra Glide) with Factory-Installed Lower Fairings 1. Install the lower fairings following the instructions in the appropriate Service Manual. For Models FLHR/I (Road King), FLHT (Electra Glide Standard) or FLHTC/I (Electra Glide Classic) with Harley- Davidson Genuine Motor Accessory Lower Fairings 1. Carefully place one lower fairing in position from behind the engine guard. 2. See Figure 1. Install the lower fairing to the top of the new engine guard with the U-bolt (6) from the back, through the holes at the top of the fairing. Install the retainer (4) in position on the U-bolt and secure to the engine guard with the two locknuts (3). Do not tighten the locknuts at this time. 3. Attach the bottom of the fairing to the engine guard with the clamp (9) removed earlier. Install the clamp around the engine guard in the direction shown, with the tabs toward the rear of the vehicle and the flat side of the clamp against the lower fairing. Insert the screw (7) through the lower fairing, rubber washer (8) and clamp (9). Secure the assembly with the locknut (10). Tighten to 12 ft-lbs (16.3 Nm) .

Incoming search terms:

2010 Harley-Davidson New Model and Technical Information

0

Filed Under (Harley Davidson) by admin on 15-12-2010

download
Meet MY2010 EPA Emissions regulations for all Harley- Davidson®vehicles sold in 50 state and Canadian markets •Reduce oxygen intrusion into the exhaust system -Promotes catalyst health and efficiency New rib/curl pipe end feature offers positive muffler stop and improved pipe consistency. 2010 Dyna®Models Crossover joints updated with new clamp and gasket. Updated joint New clamp (Comes w/gasket) New Gasket Torque 15-19 ft-lbs (20.3-25.8 Nm) 2010 Dyna®Models New 2010 FXDWG Wide Glide® New 2010 FXDWG Wide Glide® New rear fender New Floating Front Brake Rotors* New fuel tank with wider tunnel* *All Dyna®Models Current FXDB solo seat with new cover New sissybar New pillion Current FXDWG front forks with 1″shorter overall length Current FXDWG front wheel (steel) (21×2.15) black rim with chrome spokes & machined hub; Front tire pattern -GT402 FXDWG front fender 34 degree frame with tank mount boss raised by ¾” New handlebar with FXDF risers/caps *Michelin®tires on all but FXDF and FXDWG FXDB rear wheel (black rim with chrome spokes) (17×4.5) (180- 60×17), rear tire pattern -GT502 (Screamin’Eagle®) FXDF exhaust pipes & mufflers with chrome exhaust shields Gloss black rear forging covers Current FXDB rear shocks with top covers Current FXDC battery cover with chrome Wide Glide®trim Forward foot controls New 2010 FXDWG Wide Glide® Domestic tail lights Canada & all International tail lights Taillight (HDI/Canada) Side mount license plate Domestic only •Internally wired handlebar •34 degree frame with tank mount boss raised by ¾”& rear forgings moved out 2mm each side from FXDF •Flame tank replacement part is VIN restricted •Two new rear fenders (Domestic & HDI/Canada)

Incoming search terms:

Toyota 2007- 2010 Camry 2009- 2010 Venza INSTALLATION INSTRUCTIONS

0

Filed Under (Toyota Manuals) by admin on 25-09-2011

download
Turn the ignition OFF and disconnect the vehi- cle’s negative battery cable Disconnect the mass sensor electrical connection by depressing the center tab and gently pulling the harness away from the mass air sensor. Release the
two wiring harness clips from the air box lid ently pull the engine cover upward to release it from the mounting grommets. Once released, Re- move engine cover from the vehicle and set aside. 4. Disconnect the vacuum line from the intake mani- fold plenum connection. 5. Disconnect the vacuum line from the upper air box lid. Toyota
2007-10 Camry 2009-10 Venza V6-3.5L 69-8611 7. Disconnect the two vacuum lines from the “Vacuum switching valve.

Incoming search terms:

Harley Davidson Dakota Digital HLY-6000 Road Star Installation Instructions

0

Filed Under (Harley Davidson) by admin on 31-10-2010

download
The Road Star wiring is split into 2 different bundles with black connectors on the ends that were used to plug into the stock gauge cluster. Cut off both connectors. They are no longer needed The speed sensor wires on the HLY-6000 have a connector on the end that allows you to plug it directly into Harley Davidson speed sensors by using an appropriate adapter (sold separately). Luckily for us, the Road Star’s stock speed sensor will work just fine without an adapter so go ahead and cut off that connector, you don’t need it.
Ideally, the best location for the “brain box” unit of the HLY-6000 would be under the left side cover. Unfortunately, mine is full of other stuff so I had to improvise the location and decided to mount it to the back portion of the under-seat area. I would recommend that you mount yours under the left side cover though. The wires are the perfect length for that location. The brain box and wires could fit under the right side cover, but I don’t believe that the main gauge connector would reach. Using the wiring scheme on the last page of this guide, match up the wires on the Road Star with the corresponding wires on the HLY-6000 wiring harness and solder them together. Important Wiring Information: Both BLACK wires on the brain box need to be connected directly to the (-) terminal on the battery. Don’t connect them to anything else. The following wires from the Road Star are not used and can be taped off: • BLACK • RED / GREEN • BROWN The following wires from the HLY-6000 are not used and can be taped off: • GRAY • WHITE/ BLUE • WHITE (on main harness) • BROWN (*optional) The HLY-6000 has a “dimmer” function which is controlled by the BROWN wire. If you want the gauge to be bright all the time, then leave this wire disconnected. If you want the gauge to dim for night driving, then connect this wire to the GREEN Low Beam (+12v) wire

Incoming search terms:

KAWASAKI ZX-10R ROAD TEST And SPECIFICATIONS

0

Filed Under (Kawasaki) by admin on 05-11-2010

download
In the past the name Kawasaki, for me, always suggested legendary fast superbikes with brut power. Then later came the Ninja name tag and there was still a lot of speed there, but amongst the strength of some superb opposition the legend was waning. Well now the legend is back, the new 2008 Ninja ZX-10R brings back all that attitude, styling and raw power of a true superbike. As per my usual form [running a bit late] I picked up the ‘Kwacker’ from D ‘n’ D Motorcycles in Conlig all in a bit of rush. Fortunately for me, Davy the owner was as obliging as ever and kindly let me take the bike straight to the Cookstown 100 road race practice. On arrival, it was out of the van, a quick once over, tyre pressures checked and straight onto the grid to instruct the newcomers’ practice sessions. Luckily, with all the rush, I hadn’t time to dwell on the reputation of the previous models, but after one cautious lap in damp conditions the ZX-10R felt right at home among the racers. First thing I noticed, and appreciated in this situation, was that it steered really well. Turn-in and direction changes felt light and easy with no signs of the questionable high speed stability of previous ZX-10s. Suspension was slightly hard compared to some road bikes, but any softer and we would have been wallowing out of the dips. The front and rear suspension soaked up the bumpy country roads well, with the only adjustment made, being a click harder on the front rebound damping. After a few laps I really did forget I was on a road bike, such was my confidence in the big ‘Kwacker’. Talking high tech features, the ZX-10R apparently has some form of traction control system – (Kawasaki Ignition Management System) KIMS. Bit of a girly name eh! Now I’m not sure exactly how it works on this particular bike, but I can testify to an enormous amount of grip and only

2010 Toyota Motorsports/ TRD USA Contingency Award Program

0

Filed Under (Toyota Manuals) by admin on 29-09-2011

download
To enroll in the program, complete the registration form included in the enclosed material and mail, fax or e-mail it to TRD per the instructions at the bottom of the form. Contact personnel are listed on the attached 2010 Contingency Award Guidelines sheets. These people are available to assist you throughout the year. Parts Ordering: If you are planning to order Toyota parts during 2010 you must supply us with your Visa or Master Card credit card number at the time you register in the program. There is a line on the registration form for this number. See the attached Parts Ordering Guidelines for detailed information on how to order parts. TRD is looking forward to working with each of you, and we wish you a very successful year with your racing program

Incoming search terms:

2010 Honda CBR125R Track Day and School

0

Filed Under (Honda) by admin on 01-11-2011

download
A. Rookie Racers who wish to take this Officially Sanctioned School in preparation for their
participation in the 2010 Honda CBR125R Challenge held in conjunction with the 2010 Parts
Canada Superbike Championship (opening double header National round for the CBR125R
Challenge is May 27-30 at ICAR, Mirabel, north of Montreal, Quebec).
B. Current, licensed CBR125R series racers looking for track time in preparation for the upcoming
National series. Series AMB Scoring transmitters will be available for racer use at the venue.
C. Street riders who would like to try their stock CBR125R machines in a controlled environment;
Requirements:
1. Participants must be 18 years of age, or accompanied by an officially recognized parent or
guardian. The minimum age for participants is 13 – proof of age and ID are required. All
participants will be required to sign a release, waiver and minor permission Forms where
applicable. ID is required.
2. Participants must use a Snell 2005 or newer standard full face helmet, full race leathers (or
leather jacket with textile riding pants, zipped together), leather gloves and leather motorcycle
boots of at least eight inches in height.
3. Headlights and turn signals must be taped in case of breakage; mirrors must be removed.
Technical staff will be on hand to assist participants, and Orion Motorsports will provide Pirelli
tire sales, service and installation at the track during the da

Incoming search terms:

Incoming search terms: