2010 street triple 675 owners manual

You search Auto repair manual PDF 2010 street triple 675 owners manual, if there are search results will appear below. If search results do not exist, please search by others keyword.



  2010 street triple 675 owners manual Direct Download speed 5282 Kb/s

  2010 street triple 675 owners manual Full Version speed 6162 Kb/s



Daytona 675, Street Triple Street Triple R Fitting Instruction

0

Filed Under (Triumph) by admin on 29-10-2010

download
remove the original gear selector rod from the motorcycle. Note: The ball joint and locknut on the transmission linkage have a left hand thread. This is identified by either a machined ring on the gear selector rod on Daytona 675 or on the ball joint on Street Triple and Street Triple R. 1. Front ball joint 2. Locknut 3. Gear selector rod 4. Machined ring, left hand thread identification 5. Machined ring, left hand thread identification (StreetTriple and Street Triple R) 6. Remove the front and rear ball joints and front locknut only from the gear selector rod. Retain the locknut and both ball joints for re-use. Retain the gear selector rod if the motorcycle is to be returned to its original condition. 7. Remove the plastic end caps from the quickshifter assembly. 8. Screw the locknut on to the rear of the quickshifter assembly (right hand thread) leaving 8mm of thread exposed. 1. Quick shifter assembly 2. Locknut 9. Screw the rear ball joint (right hand thread) on to the rear of the quickshifter assembly until it contacts the locknut. Unscrew the ball joint, only enough to achieve the correct orientation in relation to the quickshifter cable, as shown below. Finger tighten the locknut at this stage. 1. Ball joint 2. Quickshifter assembly 3. Locknut 4. Quickshifter cable 10. Fit the locknut and front ball joint (left hand thread) to the front of the quickshifter assembly Screw the locknut and ball joint on to the quickshifter assembly to achieve a dimension between the ball joint ends of 203.5 mm. Ensure that the ball joint is in the correct orientation to the quickshifter cable, as shown below. Finger tighten the locknut at this stage. 1. Ball joint 2. Quickshifter assembly 3. Locknut 4. Quickshifter cable 12. Route the quickshifter cable through the gear selector rod aperture in the frame, as shown. 1. Quickshifter cable 2. Gear selector rod aperture 13. Locate the quickshifter assembly in position, through the frame with the sensor at the rear and the cable at the top. 1. Quick shifter assembly 2. Sensor 14. Attach the front ball joint to the transmission linkage. 1. Ball joint 2. Transmission linkage

Incoming search terms:

Daytona 675 Motorcycle Race Kit Installation Manual

0

Filed Under (Triumph) by admin on 29-10-2010

download
Remove the existing cylinder head gasket in line with the procedures detailed in the Daytona 675 service manual. 2. Fit the chosen race kit cylinder head gasket following the procedures detailed in the Daytona 675 service manual. Caution The use of the following race kit cylinder head gaskets will require changes to the fuelling settings. To alter fuelling settings a third party programmable control unit will be required. Item Description Qty 1 Head gasket (t = 0.65mm) 1 1 Head gasket (t = 0.60mm) 1 1 * Page 7 of 29 © Triumph Designs Ltd 2007. Cams, Valve Spring & Sprocket Kits Parts Supplied Camshaft Inlet Kit – A9618055 Camshaft Exhaust Kit – A9618056 Valve Spring Kit – A9618058 Camshaft Sprocket Kit – A9618057 Warning The race kit must be fitted as a complete set. If it is not fitted as a complete set a failure may result which could cause loss of motorcycle control and an accident. Caution The use of the Camshaft, Valve spring & Sprocket race kits detailed below will require changes to the fuelling settings. To alter fuelling settings a third party programmable control unit will be required. 5 5 4 1 3 2 4 3 Item Description Qty 1 Cam assy, inlet, race 1 Item Description Qty 2 Cam assy, exhaust, race 1 Item Description Qty 3 Valve spring, 14.4id, race12 Item Description Qty 4 Sprocket, camshaft, 34T 2 5 Socket head cap screw, Encapsulated, M6x10 4
Page 8 of 29 © Triumph Designs Ltd 2007. NOTE •The standard inlet cam is 9.25mm max lift and 258.50o duration. The race kit inlet cam is 9.25mm max lift and 268.74o duration. •The standard exhaust cam is 8.5mm max lift and 246o duration. The race kit exhaust cam is 8.5mm max lift and 262.21o duration. •The race kit valve spring must be used in conjunction with the standard spring platforms and retainers. The fitted length of the race springs is the same as the standard spring. 1. The race kit valve springs should be assembled in the same manner as the standard valve springs. Follow the procedure detailed in section 3 of the Daytona 675 service manual. Ensure the springs are installed with the close wound, colour coded end of the springs facing downwards, towards the piston. 2. The race kit camshafts should be assembled in the same manner as the standard camshafts. Follow the procedure detailed in section 3 of the Daytona 675 service manual. 3. The race kit cam sprockets should be mounted and secured to the camshafts using the slotted holes in the sprocket. The slotted holes allow adjustment of the valve timing. The circular holes in the sprockets are for Triumph service tool T3880102 and should not be used to mount the sprockets to the camshafts. NOTE •No timing marks are included on the race sprockets. Race engines will typically have different depths skimmed off the cylinder head and, therefore require specific individual timing. 4. The camshafts should be timed using cam degreeing equipment which typically consists of a degree wheel, pointer, dial indicator and piston stop. Optimum cam timing will depend on the exact specification of the engine, but a recommended starting point is 104o IMOP (Inlet Maximum Opening Point) and 104o EMOP (Exhaust Maximum Opening Point). 5. Always check the inlet and exhaust piston to valve clearance for the timing selected to use, before running the engine. You must ensure both clearances are adequate. As a guide, the standard nominal piston to valve clearance is 1.3mm inlet & 1.5mm exhaust

Incoming search terms:

2005-2007 KTM MOTORCYCLE REPAIR MANUAL

0

Filed Under (KTM) by admin on 21-11-2010

download
Adjustments -Take notice of the position of the compression adjustment 1 ! -Count the amount of clicks by turning the adjustment screw clockwise till fully closed. -Remove the rubber cap out of the axleclamp. -Take notice of the position of the rebound adjustment 2 ! -Count the amount of clicks by turning the adjustment screw clockwise till fully closed. -For the standard position see setting list. Position of the compression and rebound adjustment -Set the rebound position 1 , see KTM-Owners manual. -Assemble the rubber cap. -Set the compression position 2 , see KTM-Owners manual. 1 2 2-22 Repair manual WP Fork “Closed Cartridge” Art.No.: 3.211.199-E Explanation of the spring preload -Total spring length without the spacers, see chapter inspection of the spring! -Spring length with spacers 1 , see setting list. -Spring with the spacers. 1 . -The spring is assembled in the front fork leg. NOTE: the distance of “B” is less then the length of “A”. A – B = Spring preload A 1 1 B 2-23 Air release screw -Place the motorcycle on the stand. NOTE: the front wheel must be lift of the floor! -Unscrew the air release screw 1 of the screw cap on top of the front fork and tighten after approx. 10 seconds the air release screw. Recommended periodic maintenance and inspection of the 4860 SX/SXS/SMR front fork 1 A 100 liter fuel consumption is equivalent to approx. 15 operating hours Clean dust scrapers (after 1 hour) Bleed fork legs regularly – after every cleaning Check the inner tubes on scratches / leakage Visual check of damaging of the outer-tubes / replace if necessary Complete service without disass. the closed cartridge of the fork Complete service including the closed cartridge of the front fork Dismounting the fork -Place your motorcycle on a stand. -Notice the position of the front fork in the triple-clamps. NOTE: To remove the front fork. Read your KTM Instruction Manual or Workshop Manual. 3-3 Mounting the fork -Clean the innerside of the triple-clamps with brake cleaner. -Slide both fork legs into the triple-clamps. NOTE: Pay attention to the position of the fork legs. Standard riding height! NOTE: The maximum riding height is the level of the second groove! -Tighten the middle bolt of the lower triple clamp to a torque of 17 Nm! -Tighten the first bolt of the lower triple clamp to a torque of 17 Nm! -Tighten the third bolt of the lower triple clamp to a torque of 17 Nm!

Incoming search terms:

Honda CG125 Owners Manual, and repair manual

0

Filed Under (Honda) by admin on 11-12-2011

download
The author of this manual has the conviction that the only way in which a meaningful and easy to follow text can be
written is first to do the work himself, under conditions similar to those found in the average household. As a result, the hands seen in the photographs are those of the author. Even the machines are not new: examples that have covered a consider- able mileage were selected so that the conditions encountered would be typical of those found by the average owner. Unless specially mentioned, and therefore considered essential, Honda service tools have not been used. There is
invariably some alternative means of slackening or removing some vital component when service tools are not available and
isk of damage has to be avoided at all costs. Each of the six Chapters is divided into numbered Sections. Within the Sections are numbered paragraphs. In consequence, cross reference throughout this manual is both straightforward
and logical. When a reference is made ‘See Section 5.12′ it means Section 5, paragraph 12 in the same Chapter. If another
Chapter were meant, the text would read ‘See Chapter 2, Section 5.12′. All photographs are captioned with a Section/paragraph number to which they refer and are always relevant to the Chapter text adjacent. Figure numbers (usually line illustrations) appear in numerical order, within a given Chapter. Fig. 1.1 therefore refers o the first figure in Chapter 1. Left-hand and right-hand descriptions of the machines and their component parts refer to the right and left of a given machine when the rider is seated normally. Motorcycle manufacturers continually make changes to specifications and recommendations, and these, when notified,mare incorporated into our manuals at the earliest opportunity.
We take great pride in the accuracy of information given in this manual, but motorcycle manufacturers make alterations and design changes during the production run of a particular n motorcycle of which they do not inform us. No liability can be ccepted by the authors or publishers for loss, damage or injury caused by any errors in, or omissions from, the information give

Incoming search terms:

2008 ALU-RACK TRIUMPH Street Triple 675 Mounting Instruction

0

Filed Under (Triumph) by admin on 06-11-2010

download
experienced motorcycle technician. If you are unsure of your ability to properly install a product, please have the product installed by your local motorcycle dealer. SW-MOTECH takes no responsibility for damages caused by improper installation. All screws, bolts and nuts, including all replacement hardware provided by SW-MOTECH, should be tightened to the torque specified in the OEM maintenance manual for your motorcycle. If no torque specifications are provided in the OEM maintenance manual, the following torques may be used: All screws, bolts and nuts should be checked after driving the first 50 km to ensure that all are tightened to the proper torque. Medium strength liquid thread-locker (i.e., “Locktite”) should be used to secure all screws, bolts and nuts

HONDA CBX 750F OWNERS MANUAL AND REPAIR MANUAL

0

Filed Under (Honda) by admin on 02-12-2011

download
Always make a pre-ride inspection before you start the engine. You may prevent an accident or equipment damage. 2 Many accidents involve inexperienced riders. Most countries require a special riding test or license. Make sure you are qualified before you ride. NEVER lend your motorcycle to an inexperienced rider. 3 Many car/motorcycle accidents happen because the car driver does not “ see the motorcyclist. Make yourself conspicuous to help avoid the accident that is not your fault: • Wear bright or reflective clothing • Don’t drive in another motorist’s “blind spot” 4 Obey all national, and local laws and regulations Excessive speed is a factor in many accidents. Obey the speed limits am NEVER travel faster than conditions warrant • Signal before you make a turn or lane change. Your size and manoeuvrability can surprise other motorists.5 Don’t let other motorists surprise you. Use extra caution at intersections, parking entrances and exits and driveways. 6 Keep both hands on the handlebars and both feet on the footrests while riding. A passenger should hold onto the motorcycle or the rider with both hands, and keep both feet on the passenger footrests. PROTECTIVE APPAREL
1 Most motorcycle accidents fatalities are due to head impact. ALWAYS wear a helmet. You should also wear a face shield or goggles; boots, gloves, and protective clothing. A passenger needs the same protection. The exhaust system becomes very hot during operation, and it remains hot after operation. Never touch any part of the hot exhaust system. Wear clothing that fully covers your legs.
3
Do not wear loose clothing which could catch on the control levers, footrests, or wheels

HARLEY DAVIDSON VRSC CHROME WHEEL KITS INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 18-03-2011

download
Installation To prevent accidental vehicle start-up, which could cause death or serious injury, remove maxi-fuse before proceeding. (00251a) 1 WARNING 1 WARNING ® Kit Numbers 41279-04, 41282-04, 41463-05, 41467-05, 41633-05, 41634-05, 41640-05, and 41639-05 1 of 3 Figure 1. Rear Wheel Removal i02495 1. Axle (keep) 2. Axle adjuster (keep) 3. Axle nut (keep) 4. “E”-clip (keep) 5. Spacer (3) (keep) 6. Torx screw (5) (replace) 7. Brake disc (keep) 8. Wheel assembly (replace) 9. Valve cap (keep) 10. Compensator bowl (keep) 11. Compensator cushion (keep) 12.12 pt screw (5) (keep) 13. Lockwasher (5) (keep) 14. Sprocket assembly (keep) 1. Refer to the Service Manual and follow the MAXI-FUSE instructions to remove the right-side cover and maxi- fuse. Proceed to Step 2 for the wheel being replaced. Rear Wheel 2. See Figure 1. Remove the rear wheel per the REAR WHEEL, REMOVAL instructions in the Service Manual. 3. Disassemble, clean and inspect all parts to be re-used per Service Manual instructions. 4. Re-assemble all saved components to the new chrome rear wheel assembly. See REAR WHEEL, ASSEMBLY in the Service Manual. Do not re-use brake disc screws. Re-using disc screws can result in torque loss and damage to rotor and/or brake assembly. (00319b) 5. Fasten the brake disc to the valve stem side of the wheel using the Torx®screws from the kit. Install the compensator bowl with the 12-point screws and lockwashers saved earlier. 6. Install the new wheel to the rear fork. Refer to REAR WHEEL, INSTALLATION in the Service Manual. Proceed to Step 7. Front Wheel 2. See Figure 2. Remove the front wheel per the FRONT WHEEL, REMOVAL instructions in the Service Manual. 3. Disassemble, clean and inspect all parts to be re-used per Service Manual instructions. Mark the left and right brake discs so they can be re-installed to the same location. 4. Re-assemble all saved components to the new chrome front wheel assembly. See FRONT WHEEL, ASSEMBLY in the Service Manual. Do not re-use brake disc screws. Re-using disc screws can result in torque loss and damage to rotor and/or brake assembly. (00319b) 5. Using the Torx ® shoulder bolts from the kit, and the saved spring washers fasten the brake discs to the same side of the wheel from which they were removed. 6. Install the new wheel to the front forks per the FRONT WHEEL, INSTALLATION instructions in the Service Manual. Proceed to Step 7. Front and Rear Wheels 7. Refer to the Service Manual and follow the MAXI-FUSE instructions to replace the maxi-fuse and right-side cover. After servicing brakes and before moving motorcycle, pump brakes to build brake system pressure. Insufficient pressure can adversely affect brake performance, which could result in death or serious injury. (00279a) After servicing the brake system, test brakes at low speed. If brakes are not operating properly, testing at high speeds can cause loss of control, which could result in death or serious injury. (00289a) Maintenance and Cleaning Chrome parts must be maintained regularly to ensure that they keep their original shine and luster. 1. Clean heavily-soiled wheel surfaces using Harley Wheel and Tire Cleaner, part number 94658-98, applied with Harley Wheel and Spoke Brush, part number 43078-99. 2. Thoroughly clean chrome with a good quality chrome cleaner, such as Harley Bright Chrome Cleaner, part number 94683-99. 3. After cleaning and polishing, seal the finish with a good quality sealer such as Harley Glaze Polish and Sealant, part number 99701-84

Incoming search terms:

SUZUKI GSX-R1000 SERVICE MANUAL

0

Filed Under (Suzuki) by admin on 12-11-2010

download
Cover the throttle bodies to prevent anything from dropping into the engine. 1. Remove the front seat and disconnect the battery. (Refer to Service Manual, Page 8-8) 2. Lift up the fuel tank. (Refer to Service Manual, Page 5-3) 3. Remove the air cleaner box. (Refer to Service Manual, Page 5-14) 4. Remove and replace the ISC valve. (Refer to Service Manual, Page 5-25) NOTE: Since the ECM is also being replaced there is no need to perform the ISC valve preset operation. 5. Install the air cleaner box in reverse order of removal. (Refer to Service Manual, Page 5-14) 6. Lower the fuel tank. (Refer to Service Manual, Page 5-3) 7. Remove the upper seat rail plate. Disconnect and remove the ECM. (Figure 1) @ ISC Valve Mounting Screw Torque: 2.1± ±0.6 N.m (1.5± ±0.4 lb-ft) ! Carefully insert the ISC valve straight into the throttle body hole to prevent damaging the o-ring. Turn the ISC valve slightly to confirm that the o-ring has not twisted. Using the new screw provided in the replacement parts kit, make sure the screw is completely seated on the plate after the screw has been tightened to the specified torque. 4. Remove and replace the ISC valve. (Refer to Service Manual, Page 5-25) NOTE: Since the ECM is also being replaced there is no need to perform the ISC valve preset operation. ! Cover the throttle bodies to prevent anything from dropping into the engine. 1. Remove the front seat and disconnect the battery. (Refer to Service Manual, Page 8-8) 2. Lift up the fuel tank. (Refer to Service Manual, Page 5-3) 3. Remove the air cleaner box. (Refer to Service Manual, Page 5-14) REPLACEMENT PROCEDURE: 8. Install the new ECM in reverse order of removal. Apply thread lock to the upper plate mounting bolts when reinstalling the upper seat rail plate.

Incoming search terms:

HARLEY DAVIDSON SCREAMIN' EAGLE TWIN CAM 110 (1800 CC) CONVERSION KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 19-02-2011

download
REMOVAL Prepare for Service 1. Position motorcycle on a suitable lift. NOTE If vehicle is equipped with Harley-Davidson Smart Security System, see owner’s manual for instructions to disarm the system. To prevent accidental vehicle start-up, which could cause death or serious injury, disconnect negative (-) battery cable before proceeding. (00048a) 2. Disconnect battery cables, negative (-) battery cable first. 3. Remove seat according to the instructions in the service manual. 4. Refer to service manual to remove left saddlebag and side cover. When servicing the fuel system, do not smoke or allow open flame or sparks in the vicinity. Gasoline is extremely flammable and highly explosive, which could result in death or serious injury. (00330a) 5. Remove fuel tank according to the instructions in the service manual. Remove Engine Components 1. Remove existing air cleaner assembly. Discard backplate but save remaining parts. Refer to AIR CLEANER REMOVAL in service manual. 2. Remove existing exhaust system. Refer to EXHAUST SYSTEM REMOVAL in service manual. 3. Remove engine from chassis following the instructions in the service manual. 4. Disassemble engine top end and bottom end. Refer to appropriate ENGINE sections in service manual. 5. Remove existing clutch diaphragm spring. Refer to CLUTCH REMOVAL in service manual. The procedures in this instruction sheet should be performed by one experienced in precision measuring techniques. Failure to meet tolerances called for in this instruction sheet can result in engine damage. (00511b) -J04793 1 2 is03517 1. O-ring counterbore 2. Spigot bore Figure 1. Spigot Bore and O-Ring Counterbore Dimensions Table 1. Spigot Bore and O-Ring Counterbore Dimensions Depth Bore Description 1.625 +/- 0.010 in. (41.3 +/- 0.25 mm) 4.205 +/- 0.010 in. (107 +/- 0.25 mm) Spigot Bore 0.085 +/- 0.003 in. (2.16 +/- 0.08 mm) 4.415 +/- 0.002 in. (112 +/- 0.05 mm) O-Ring Counter- bore is03456 Figure 2. Cylinder Wall MACHINE CRANKCASE Crankcase Boring Preparation NOTE During final assembly of the engine, Harley-Davidson recommends replacing the OE cylinder studs with Screamin’ Eagle High Tensile Studs (16505-01). 1. Remove cylinder studs from the engine crankcase. 2. Mask off all bearings and oil holes to prevent debris and contaminants from entering those areas. 3. Inspect and clean engine case mating surfaces. 4. See Figure 6. Reassemble engine case with OE screws, except the top center screw between the cylinders, and tighten to specifications listed in service manual. NOTE To prevent damage to crankcase boring tool, it is important to replace the top center screw with a modified top center screw (1093). This screw is included in the Crankcase Boring Tool Kit (94419-06) and can be purchased separately from a Harley- Davidson dealer. 5. Install modified top center screw (1093) between the cylinders and tighten to 50-90 in-lbs (5.6-10.2 Nm). 6. See Figure 1 and Table 1. Machine crankcase cylinder spigot bore and O-ring counterbore to the dimensions shown. Modify Crankcase

Incoming search terms:

2009 Daytona 675 Motorcycle Race Kit Manual

0

Filed Under (Triumph) by admin on 29-10-2010

download
1. Remove the existing cylinder head gasket in line with the procedures detailed in the Daytona 675 service manual. 2. Position a piece of solder (with a diameter approximately 1.3 mm) on the four squish surfaces of each piston. Position the solder in line with the corresponding squish surfaces on the cylinder head and hold in place with a small amount of grease. 3. Refit the cylinder head with the head gasket. 4. Slowly turn the engine over, by hand, to compress the solder to the same height as the squish clearance. 5. Remove the cylinder head and head gasket. 6. Measure the compressed thickness of the solder. The squish clearance must be a minimum of 0.65 mm. If the thickness of the solder is less than 0.65 mm repeat steps 2 to 6 with a thicker head gasket until the squish clearance is at an acceptable level. NOTE •In some cases, it may be necessary to use a standard cylinder head gasket to achieve the correct squish clearance. 7. Fit the chosen cylinder head gasket following the procedures detailed in the Daytona 675 service manual. Warning Running the engine at less than the minimum recommended squish height can lead to the pistons contacting the cylinder head, causing major engine damage. This could cause loss of motorcycle control and an accident. Triumph Designs Ltd 2009. Camshaft, Valve Spring & Camshaft Sprocket Kits Parts Supplied Camshaft, Inlet – A9618055 Camshaft, Exhaust – A9618056 Valve Spring Kit – A9618086 Camshaft Sprocket Kit – A9618095 Warning The Race Kit camshaft, valve Spring and camshaft sprockets must be fitted as a complete set. If they are not fitted as a complete set a failure may result which could cause loss of motorcycle control and an accident. Caution The use of The Race Kit camshaft, valve Spring and camshaft sprockets detailed below will require changes to the fuelling and ignition settings. To alter these settings, a Triumph Programmable Race ECU combined with Triumph TRACS Race Calibration Software will be required. Failure to correct the fuelling and ignition settings will result in poor engine performance and could result in engine damage.

Incoming search terms: