2010 triumph street triple r manual

You search Auto repair manual PDF 2010 triumph street triple r manual, if there are search results will appear below. If search results do not exist, please search by others keyword.



  2010 triumph street triple r manual Direct Download speed 5282 Kb/s

  2010 triumph street triple r manual Full Version speed 6162 Kb/s



Daytona 675, Street Triple Street Triple R Fitting Instruction

0

Filed Under (Triumph) by admin on 29-10-2010

download
remove the original gear selector rod from the motorcycle. Note: The ball joint and locknut on the transmission linkage have a left hand thread. This is identified by either a machined ring on the gear selector rod on Daytona 675 or on the ball joint on Street Triple and Street Triple R. 1. Front ball joint 2. Locknut 3. Gear selector rod 4. Machined ring, left hand thread identification 5. Machined ring, left hand thread identification (StreetTriple and Street Triple R) 6. Remove the front and rear ball joints and front locknut only from the gear selector rod. Retain the locknut and both ball joints for re-use. Retain the gear selector rod if the motorcycle is to be returned to its original condition. 7. Remove the plastic end caps from the quickshifter assembly. 8. Screw the locknut on to the rear of the quickshifter assembly (right hand thread) leaving 8mm of thread exposed. 1. Quick shifter assembly 2. Locknut 9. Screw the rear ball joint (right hand thread) on to the rear of the quickshifter assembly until it contacts the locknut. Unscrew the ball joint, only enough to achieve the correct orientation in relation to the quickshifter cable, as shown below. Finger tighten the locknut at this stage. 1. Ball joint 2. Quickshifter assembly 3. Locknut 4. Quickshifter cable 10. Fit the locknut and front ball joint (left hand thread) to the front of the quickshifter assembly Screw the locknut and ball joint on to the quickshifter assembly to achieve a dimension between the ball joint ends of 203.5 mm. Ensure that the ball joint is in the correct orientation to the quickshifter cable, as shown below. Finger tighten the locknut at this stage. 1. Ball joint 2. Quickshifter assembly 3. Locknut 4. Quickshifter cable 12. Route the quickshifter cable through the gear selector rod aperture in the frame, as shown. 1. Quickshifter cable 2. Gear selector rod aperture 13. Locate the quickshifter assembly in position, through the frame with the sensor at the rear and the cable at the top. 1. Quick shifter assembly 2. Sensor 14. Attach the front ball joint to the transmission linkage. 1. Ball joint 2. Transmission linkage

Incoming search terms:

2009 TRIUMPH DAYTONA 675 Triumph/ Arrow Race Rearsets

0

Filed Under (Triumph) by admin on 12-11-2010

download
race harness kit, air funnel kit, racing oil pump gearing kit, adjustable camshaft sprocket kit, manual camshaft tensioner and blade kit, a reusable engine cover gasket set and racing cylinder head gaskets. Here’s a closer look at the new racing parts and their associated performance improvements: TRACS – Triumph Race Calibration Software TRACS ( T riumph Ra ce C alibration S oftware) is a new computer program that allows racers to tune Triumph’s programmable race ECU from a laptop PC. Developed by one of Triumph’s most experienced EFI calibration engineers, the programmable ECU and software was created for the growing number of competitors that are riding Triumph motorcycles at the track. The new software provides racers with quick access to a wide range of adjustments that can be downloaded to the race ECU in about 35 seconds for tuning during testing, practice and qualifying sessions. Features include: Fully programmable fuel mapping (500rpm increments, for individual cylinders). Fully programmable ignition mapping. Switchable wet and dry maps. Adjustable pit lane speed limiter and speedo calibration. Adjustable quickshifter cut duration (adjustable at low, mid and high RPM) Adjustable rev limiter up to 15,000rpm. New software strategies to improve throttle progression. Optimized software to run faster to cater for the higher RPMs involved in a race environment. Ability to save multiple maps within the memory of the PC. Ability to update an existing 2007/2008 Race ECU to 2009 specification and functionality.* (*Not all features will be available if using the 2007/08 Race harness.) Exhaust – Triumph/Arrow Titanium “Stage 3″ System Triumph has continued to collaborate with Italian race exhaust specialists Arrow Special Parts to develop a new, full titanium racing exhaust system. This system complies with current FIM regulations, works as part of the factory race kit, and offers a significant weight reduction and considerable power gains.

Incoming search terms:

2005-2007 KTM MOTORCYCLE REPAIR MANUAL

0

Filed Under (KTM) by admin on 21-11-2010

download
Adjustments -Take notice of the position of the compression adjustment 1 ! -Count the amount of clicks by turning the adjustment screw clockwise till fully closed. -Remove the rubber cap out of the axleclamp. -Take notice of the position of the rebound adjustment 2 ! -Count the amount of clicks by turning the adjustment screw clockwise till fully closed. -For the standard position see setting list. Position of the compression and rebound adjustment -Set the rebound position 1 , see KTM-Owners manual. -Assemble the rubber cap. -Set the compression position 2 , see KTM-Owners manual. 1 2 2-22 Repair manual WP Fork “Closed Cartridge” Art.No.: 3.211.199-E Explanation of the spring preload -Total spring length without the spacers, see chapter inspection of the spring! -Spring length with spacers 1 , see setting list. -Spring with the spacers. 1 . -The spring is assembled in the front fork leg. NOTE: the distance of “B” is less then the length of “A”. A – B = Spring preload A 1 1 B 2-23 Air release screw -Place the motorcycle on the stand. NOTE: the front wheel must be lift of the floor! -Unscrew the air release screw 1 of the screw cap on top of the front fork and tighten after approx. 10 seconds the air release screw. Recommended periodic maintenance and inspection of the 4860 SX/SXS/SMR front fork 1 A 100 liter fuel consumption is equivalent to approx. 15 operating hours Clean dust scrapers (after 1 hour) Bleed fork legs regularly – after every cleaning Check the inner tubes on scratches / leakage Visual check of damaging of the outer-tubes / replace if necessary Complete service without disass. the closed cartridge of the fork Complete service including the closed cartridge of the front fork Dismounting the fork -Place your motorcycle on a stand. -Notice the position of the front fork in the triple-clamps. NOTE: To remove the front fork. Read your KTM Instruction Manual or Workshop Manual. 3-3 Mounting the fork -Clean the innerside of the triple-clamps with brake cleaner. -Slide both fork legs into the triple-clamps. NOTE: Pay attention to the position of the fork legs. Standard riding height! NOTE: The maximum riding height is the level of the second groove! -Tighten the middle bolt of the lower triple clamp to a torque of 17 Nm! -Tighten the first bolt of the lower triple clamp to a torque of 17 Nm! -Tighten the third bolt of the lower triple clamp to a torque of 17 Nm!

2008 ALU-RACK TRIUMPH Street Triple 675 Mounting Instruction

0

Filed Under (Triumph) by admin on 06-11-2010

download
experienced motorcycle technician. If you are unsure of your ability to properly install a product, please have the product installed by your local motorcycle dealer. SW-MOTECH takes no responsibility for damages caused by improper installation. All screws, bolts and nuts, including all replacement hardware provided by SW-MOTECH, should be tightened to the torque specified in the OEM maintenance manual for your motorcycle. If no torque specifications are provided in the OEM maintenance manual, the following torques may be used: All screws, bolts and nuts should be checked after driving the first 50 km to ensure that all are tightened to the proper torque. Medium strength liquid thread-locker (i.e., “Locktite”) should be used to secure all screws, bolts and nuts

HARLEY DAVIDSON SCREAMIN' EAGLE TWIN CAM 110 (1800 CC) CONVERSION KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 19-02-2011

download
REMOVAL Prepare for Service 1. Position motorcycle on a suitable lift. NOTE If vehicle is equipped with Harley-Davidson Smart Security System, see owner’s manual for instructions to disarm the system. To prevent accidental vehicle start-up, which could cause death or serious injury, disconnect negative (-) battery cable before proceeding. (00048a) 2. Disconnect battery cables, negative (-) battery cable first. 3. Remove seat according to the instructions in the service manual. 4. Refer to service manual to remove left saddlebag and side cover. When servicing the fuel system, do not smoke or allow open flame or sparks in the vicinity. Gasoline is extremely flammable and highly explosive, which could result in death or serious injury. (00330a) 5. Remove fuel tank according to the instructions in the service manual. Remove Engine Components 1. Remove existing air cleaner assembly. Discard backplate but save remaining parts. Refer to AIR CLEANER REMOVAL in service manual. 2. Remove existing exhaust system. Refer to EXHAUST SYSTEM REMOVAL in service manual. 3. Remove engine from chassis following the instructions in the service manual. 4. Disassemble engine top end and bottom end. Refer to appropriate ENGINE sections in service manual. 5. Remove existing clutch diaphragm spring. Refer to CLUTCH REMOVAL in service manual. The procedures in this instruction sheet should be performed by one experienced in precision measuring techniques. Failure to meet tolerances called for in this instruction sheet can result in engine damage. (00511b) -J04793 1 2 is03517 1. O-ring counterbore 2. Spigot bore Figure 1. Spigot Bore and O-Ring Counterbore Dimensions Table 1. Spigot Bore and O-Ring Counterbore Dimensions Depth Bore Description 1.625 +/- 0.010 in. (41.3 +/- 0.25 mm) 4.205 +/- 0.010 in. (107 +/- 0.25 mm) Spigot Bore 0.085 +/- 0.003 in. (2.16 +/- 0.08 mm) 4.415 +/- 0.002 in. (112 +/- 0.05 mm) O-Ring Counter- bore is03456 Figure 2. Cylinder Wall MACHINE CRANKCASE Crankcase Boring Preparation NOTE During final assembly of the engine, Harley-Davidson recommends replacing the OE cylinder studs with Screamin’ Eagle High Tensile Studs (16505-01). 1. Remove cylinder studs from the engine crankcase. 2. Mask off all bearings and oil holes to prevent debris and contaminants from entering those areas. 3. Inspect and clean engine case mating surfaces. 4. See Figure 6. Reassemble engine case with OE screws, except the top center screw between the cylinders, and tighten to specifications listed in service manual. NOTE To prevent damage to crankcase boring tool, it is important to replace the top center screw with a modified top center screw (1093). This screw is included in the Crankcase Boring Tool Kit (94419-06) and can be purchased separately from a Harley- Davidson dealer. 5. Install modified top center screw (1093) between the cylinders and tighten to 50-90 in-lbs (5.6-10.2 Nm). 6. See Figure 1 and Table 1. Machine crankcase cylinder spigot bore and O-ring counterbore to the dimensions shown. Modify Crankcase

Incoming search terms:

HARLEY DAVIDSON VRSC CHROME WHEEL KITS INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 18-03-2011

download
Installation To prevent accidental vehicle start-up, which could cause death or serious injury, remove maxi-fuse before proceeding. (00251a) 1 WARNING 1 WARNING ® Kit Numbers 41279-04, 41282-04, 41463-05, 41467-05, 41633-05, 41634-05, 41640-05, and 41639-05 1 of 3 Figure 1. Rear Wheel Removal i02495 1. Axle (keep) 2. Axle adjuster (keep) 3. Axle nut (keep) 4. “E”-clip (keep) 5. Spacer (3) (keep) 6. Torx screw (5) (replace) 7. Brake disc (keep) 8. Wheel assembly (replace) 9. Valve cap (keep) 10. Compensator bowl (keep) 11. Compensator cushion (keep) 12.12 pt screw (5) (keep) 13. Lockwasher (5) (keep) 14. Sprocket assembly (keep) 1. Refer to the Service Manual and follow the MAXI-FUSE instructions to remove the right-side cover and maxi- fuse. Proceed to Step 2 for the wheel being replaced. Rear Wheel 2. See Figure 1. Remove the rear wheel per the REAR WHEEL, REMOVAL instructions in the Service Manual. 3. Disassemble, clean and inspect all parts to be re-used per Service Manual instructions. 4. Re-assemble all saved components to the new chrome rear wheel assembly. See REAR WHEEL, ASSEMBLY in the Service Manual. Do not re-use brake disc screws. Re-using disc screws can result in torque loss and damage to rotor and/or brake assembly. (00319b) 5. Fasten the brake disc to the valve stem side of the wheel using the Torx®screws from the kit. Install the compensator bowl with the 12-point screws and lockwashers saved earlier. 6. Install the new wheel to the rear fork. Refer to REAR WHEEL, INSTALLATION in the Service Manual. Proceed to Step 7. Front Wheel 2. See Figure 2. Remove the front wheel per the FRONT WHEEL, REMOVAL instructions in the Service Manual. 3. Disassemble, clean and inspect all parts to be re-used per Service Manual instructions. Mark the left and right brake discs so they can be re-installed to the same location. 4. Re-assemble all saved components to the new chrome front wheel assembly. See FRONT WHEEL, ASSEMBLY in the Service Manual. Do not re-use brake disc screws. Re-using disc screws can result in torque loss and damage to rotor and/or brake assembly. (00319b) 5. Using the Torx ® shoulder bolts from the kit, and the saved spring washers fasten the brake discs to the same side of the wheel from which they were removed. 6. Install the new wheel to the front forks per the FRONT WHEEL, INSTALLATION instructions in the Service Manual. Proceed to Step 7. Front and Rear Wheels 7. Refer to the Service Manual and follow the MAXI-FUSE instructions to replace the maxi-fuse and right-side cover. After servicing brakes and before moving motorcycle, pump brakes to build brake system pressure. Insufficient pressure can adversely affect brake performance, which could result in death or serious injury. (00279a) After servicing the brake system, test brakes at low speed. If brakes are not operating properly, testing at high speeds can cause loss of control, which could result in death or serious injury. (00289a) Maintenance and Cleaning Chrome parts must be maintained regularly to ensure that they keep their original shine and luster. 1. Clean heavily-soiled wheel surfaces using Harley Wheel and Tire Cleaner, part number 94658-98, applied with Harley Wheel and Spoke Brush, part number 43078-99. 2. Thoroughly clean chrome with a good quality chrome cleaner, such as Harley Bright Chrome Cleaner, part number 94683-99. 3. After cleaning and polishing, seal the finish with a good quality sealer such as Harley Glaze Polish and Sealant, part number 99701-84

Incoming search terms:

SUZUKI GSX-R1000 SERVICE MANUAL

0

Filed Under (Suzuki) by admin on 12-11-2010

download
Cover the throttle bodies to prevent anything from dropping into the engine. 1. Remove the front seat and disconnect the battery. (Refer to Service Manual, Page 8-8) 2. Lift up the fuel tank. (Refer to Service Manual, Page 5-3) 3. Remove the air cleaner box. (Refer to Service Manual, Page 5-14) 4. Remove and replace the ISC valve. (Refer to Service Manual, Page 5-25) NOTE: Since the ECM is also being replaced there is no need to perform the ISC valve preset operation. 5. Install the air cleaner box in reverse order of removal. (Refer to Service Manual, Page 5-14) 6. Lower the fuel tank. (Refer to Service Manual, Page 5-3) 7. Remove the upper seat rail plate. Disconnect and remove the ECM. (Figure 1) @ ISC Valve Mounting Screw Torque: 2.1± ±0.6 N.m (1.5± ±0.4 lb-ft) ! Carefully insert the ISC valve straight into the throttle body hole to prevent damaging the o-ring. Turn the ISC valve slightly to confirm that the o-ring has not twisted. Using the new screw provided in the replacement parts kit, make sure the screw is completely seated on the plate after the screw has been tightened to the specified torque. 4. Remove and replace the ISC valve. (Refer to Service Manual, Page 5-25) NOTE: Since the ECM is also being replaced there is no need to perform the ISC valve preset operation. ! Cover the throttle bodies to prevent anything from dropping into the engine. 1. Remove the front seat and disconnect the battery. (Refer to Service Manual, Page 8-8) 2. Lift up the fuel tank. (Refer to Service Manual, Page 5-3) 3. Remove the air cleaner box. (Refer to Service Manual, Page 5-14) REPLACEMENT PROCEDURE: 8. Install the new ECM in reverse order of removal. Apply thread lock to the upper plate mounting bolts when reinstalling the upper seat rail plate.

Incoming search terms:

Triumph TT 600 Installation instructions

0

Filed Under (Triumph) by admin on 28-10-2010

download
1) It is essential to use Blue Loc-tite on all setscrews and bolts or they will come loose. 2) Remove the stock 30mm nut AND washer , that holds the top triple clamp tight and discard them. 3) Install the new aluminum nut supplied in the kit with the Hex drive facing up and torque to 45 ft. lbs. or more. 4) Install the new “triple clamp damper mount” (TC mount), the part with 6 set screws in it , over the main triple clamp nut with the “machined register” (lip) indexing over the back of the triple clamp (see photo below). Tip to save time: Before installation, using Loc-tite, start all the setscrews first, until flush with the inside bore. 5) Be sure this damper mounting bracket is setting flush on the triple clamp surface all the way around. This part is machined precisely to fit over the stock triple clamp. Due to the fact the stock triple clamp is cast, they could vary is size. Remove or trim around any obstructions that might prevent the TC mount from sitting down flush such as carbon fiber deco plates. 6) Loc-tite and engage the setscrew at the 12 o’clock (front) position first so it pulls the “register up against the back of your triple clamp. Do not tighten this setscrew, just snug it enough to secure the position of the TC mount. 7) Loc-tite and tighten the remaining setscrews evenly until they make contact with the groove and are secured tightly. It’s a good idea to check the setscrews after the first ride as they will seat into their final position and need re-tightening. 8) Tip to save time: Before installation, using Loc-tite start all the setscrews first, until flush with the inside bore. 9) (Note: You must use some heat to compromise the Loc-tite before trying to remove the setscrews or the small Allen head setscrews can be stripped easily). 10) Remove the stock front fuel tank retaining bolt and washer. You must use the longer 6×30 bolt provided . 11) Retain the rubber bushing and the spacer-washer that fits inside the rubber bushing for your tank mount. 12) The gas tank mounting hole is actually off-center from the factory on this bike, by only 1mm or so, so our frame bracket has a slot instead of hole so you can make fine adjustments in the alignment of the frame bracket. 13) Install the frame bracket so the “feet” that contact the frame are positioned to match the frame. View the photo below to see how it should look and remain straight with the front edge of the gas tank. There is a front and back to this part. 14) We’ve machined this frame bracket precisely to match the Triumph frame, so as the bolt tightens up it will pre-load the frame bracket just enough to secure it tightly to the frame. 15) Remember, under heavy braking your entire body weight is pushing the tank forward. Until you have verified sufficient clearance between the tank and the frame bracket, put something between the tank and frame bracket to protect the tank. Each bike will vary as to how much movement there actually is under heavy braking 16) Grease the tower-pin lightly and drop it in the tower-pin hole. It is designed to “float”. Keep the hole and shaft portion of the tower pin greased for easy movement. 17) Install the stabilizer using (2) 6×20 Allens. The link arm slot aligns with the flats on the tower pin. 18) Read your damper manual for initial settings on the controls.

HARLEY DAVIDSON STREET SLAMMER HANDLEBAR KIT REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 15-02-2011

download
This kit does not fit models equipped with Hydraulic Clutch Kits, handlebar mounted gauges or the Road Tech® Radio or FLHRS models equipped with an accessory windshield. REMOVAL Preparation – All Models To prevent accidental vehicle start-up, which could cause death or serious injury, remove main fuse before proceeding. (00251b) To prevent accidental vehicle start-up, which could cause death or serious injury, disconnect battery cables (negative (-) cable first) before proceeding. (00307a) Disconnect negative (-) battery cable first. If positive (+) cable should contact ground with negative (-) cable connected, the resulting sparks can cause a battery explosion, which could result in death or serious injury. (00049a) 1. See the service manual and remove the seat and disconnect battery cables or remove the main fuse. Save the seat hardware for installation. -J04406 When servicing the fuel system, do not smoke or allo w open flame or sparks in the vicinity. Gasoline is extremely flammable and highly explosive, which could result in death or serious injury. (00330a) 2. Softail and Dyna models: See the service manual and loosen the fuel tank. Direct contact of D.O.T. 5 brake fluid with eyes can cause eye irritation, swelling, and redness. Avoid eye contact. In case of eye contact flush with large amounts of water and get medical attention. Swallowing large amounts of D.O.T. 5 brake fluid can cause digestive discomfort. If swallowed, obtain medical attention. Use in well ventilated area. KEEP OUT OF REACH OF CHILDREN. (00144a) Direct contact of D.O.T. 4 brake fluid with eyes can cause irritation. Avoid eye contact. In case of eye contact flush with large amounts of water and get medical attention. Swallowing large amounts of D.O.T. 4 brake fluid can cause digestive discomfort. If swallowed, obtain medical attention. Use in well ventilated area. KEEP OUT OF REACH OF CHILDREN. (00240a) D.O.T. 4 brake fluid will damage painted and body panel surfaces it comes in contact with. Always use caution and protect surfaces from spills whenever brake work is performed. Failure to comply can result in cosmetic damage. (00239b) NOTES Immediately wipe up any brake fluid spills with a clean, dry, soft cloth. Follow up by thoroughly wiping affected area with a clean, damp, soft cloth (small spills) or washing with a large quantity of soapy water (large spills). Cover nearby motorcycle surfaces with a polyethylene protective sheet to help protect against damage to finish caused by spilled DOT 4 brake fluid. 3. See the service manual and drain the brake fluid from the front brake reservoir and brake lines. Handlebar Removal – Dyna and Softail NOTE Cover the front fender and the fuel tank with clean shop towels to prevent scratching. Damage to the finish could result. 1. Note the front brake line routing and the orientation of the banjo fittings. See the service manual and disconnect and remove the brake line. Save the banjo bolts, but discard the brake line gaskets. 2. Remove the plastic wiring retainer clips that secure the turn signal harnesses to the handlebar, if equipped. 3. Remove the front brake master cylinder and clutch lever assemblies from the handlebar.

HARLEY DAVIDSON DYNA STATOR AND ROTOR KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 30-03-2011

download
REMOVAL To prevent accidental vehicle start-up, which could cause death or serious injury, disconnect negative (-) battery cable before proceeding. (00048a) 1. Disconnect negative battery cable. See BATTERY MAINTENANCE in Service Manual. 2. Remove primary cover, primary drive, and clutch. See DRIVE COMPONENTS in Service Manual. 3. Remove primary chaincase according to the instructions in the Service Manual. 4. See Figure 2. Pull off the alternator rotor (1) using two bolts inserted through the holes in the rotor face. 5. Remove the two T-27 TORX screws (2). 6. Unplug the voltage regulator and remove the stator (3). See VOLTAGE REGULATOR in Service Manual. 7. Disassemble connector [46B] (A). See DEUTSCH ELECTRICAL CONNECTORS in Service Manual. NOTE Contact cleaner, alcohol, or glass cleaner sprayed on rubber grommet (B) will provide lubrication when pulling it through crankcase hole. 8. Move grommet (3) to one side and spray contact cleaner into gap. Repeat for other side. Pull rubber grommet (B) through crankcase hole. 9. Pull wires through crankcase hole. INSTALLATION 1. Insert wires through crankcase hole. 2. See Figure 1. Push rubber grommet (B) through crankcase hole. If necessary, apply the same lubricant used during removal. 3. Insert wires into connector [46B] (A). 4. Mate connector [46]. See VOLTAGE REGULATOR in Service Manual. is03776 Figure 1. Voltage Regulator 5. See Figure 2. Install the stator (3) on the crankcase and fasten in place using new TORX screws (2). Tighten to 55-75 in-lbs (6.2-8.4 Nm). 6. Install the rotor (1) on the sprocket shaft. 7. Apply Loctite Threadlocker 262 (red) to sprocket nut threads. Tighten sprocket nut to 150-165 ft-lbs (203.4- 223.7 Nm). 8. Install primary chaincase according to the instructions in the Service Manual. 9. Install clutch, primary drive, and primary cover. See DRIVE COMPONENTS in Service Manual. 10. Connect negative battery cable. See BATTERY MAINTENANCE in Service Manual

Incoming search terms: