2011 harley sportster front blnker plug wiring removal

You search Auto repair manual PDF 2011 harley sportster front blnker plug wiring removal, if there are search results will appear below. If search results do not exist, please search by others keyword.



  2011 harley sportster front blnker plug wiring removal Direct Download speed 5282 Kb/s

  2011 harley sportster front blnker plug wiring removal Full Version speed 6162 Kb/s



SUZUKI SV1000 PERIODIC MAINTENANCE

0

Filed Under (Suzuki) by admin on 26-02-2011

download
MAINTENANCE AND TUNE-UP PRO- CEDURES This section describes the servicing procedures for each item of the Periodic Maintenance requirements. AIR CLEANER I Inspect every 6 000 km (4 000 miles, 6 months) and replace every 18 000 km (11 000 miles, 18 months) . • * Remove the seat. (LF6-7) • * Lift and support the feul tank . (C-74-65) • * Remove the air cleaner box cap O. • * Remove the air cleaner element O. • * Carefully use air hose to blow the dust from the cleaner ele- ment. CAUTION Always use air pressure on the throttle body side of the air cleaner element . If air pressure is used on the other side, dirt will be forced into the pores of the air cleaner element thus restricting air flow through the air cleaner element . PERIODIC MAINTENANCE 2-5 2-6PERIODIC MAINTENANCE • * Reinstall the cleaned or new air cleaner element in the reverse order of removal . CAUTION If driving under dusty condition, clean the air cleaner element more frequently. The surest way to accelerate engine wear is to use the engine without the element or to use a ruptured element. Make sure that the air cleaner is in good condition at all times. Life of the engine depends largely on this component! NOTE: When cleaning the air cleaner element, drain water from the air cleaner by removing the drain plug . SPARK PLUG Inspect every 6 000 km (4 000 miles, 6 months) and replace every 12 000 km (7 500 miles, 12 months) . No. 1 (FRONT) SPARK PLUG REMOVAL • * Remove the radiator mounting bolt O. • * Move the radiator forward. • * Remove the spark plug cap O. NOTE: Be careful not to damage the radiator fins . A WARNING The hot radiator and the hot engine can burn you . Wait until the radiator and the engine are cool enough to touch . • * Remove the spark plug with a spark plug wrench. 1 6 I It No. 2 (REAR) SPARK PLUG REMOVAL • * Remove the seat. (r–,-6-7) • * Lift and support the fuel tank . (=4-65) 4-65) • * Disconnect the camshaft position sensor 1O and breather hose (Z. • * Remove the rubber heat shield ® . • * Remove the spark plug cap . • * Remove the spark plug with a spark plug wrench . HEAT RANGE • * Check to see the heat range of the plug . CARBON DEPOSIT •Check to see if there are carbon deposits on the plugs . If carbon is deposited, remove it with a spark plug cleaner machine or carefully using a tool with a pointed end . SPARK PLUG GAP • * Measure the plug gap with a thickness gauge . If out of specification, adjust it to the following gap . 09900-20803 : Thickness gauge Spark plug gap OA Standard: 0.6 – 0 .7 mm (0.024 -0.028 in) ELECTRODES CONDITION •Check to see the worn or burnt condition of the electrodes . If it is extremely worn or burnt, replace the plug . And also replace the plug if it has a broken insulator, damaged thread . CAUTION Confirm the thread size and reach when replacing the plug. If the reach is too short, carbon will be deposited on the screw portion of the plug hole and engine damage may result

Incoming search terms:

Harley-Davidson Sportster 883/ 1200 Straightshot HS Exhaust system REMOVAL AND INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 19-12-2010

download
STOCK EXHAUST SYSTEM REMOVAL 1. Loosen the heat shield clamps on both the front and rear exhaust pipes. This allows easier access to the head pipe mounting nuts. 2. Remove the two head pipe mounting nuts from each flange, located at the cylinder head. 3. Remove the two bolts from each muffler body which attach the muffler bodies to the mounting bar. 4. Remove the clamp bolt which mounts the rear head Page 1 of 4 D445N Rev. 1.0 Sportster 883/1200 Straightshot HS Exhaust system Part #17815 U S A Congratulations, you have purchased the finest exhaust system available for your motorcycle. Your VANCE & HINES exhaust system is designed and crafted for maximum performance, a perfect fit, a great sound and unbeatable style! Please follow the installation instructions below and if you have any questions, feel free to call our technical help line (562) 926-5291. Attention Installer: (if other than owner): Please forward this instruction sheet to the purchaser of this product. These instructions contain valuable information necessary to the end user. Tools required for installation: 3/16″ & 5/16″ Allen wrenches 3/16″ & 5/16″ Allen & 1/2″ sockets 3/8″ Ratchet & Extensions T30 Torx driver 1/2″ Wrench 5/16″ nutdriver/flat blade screwdriver Ft/lb. & In/lb. Torque wrenches Snapring pliers pipe to the belt drive cover bracket and carefully remove both exhaust pipes from the motorcycle. 5. Remove the drive belt cover and take the bracket off the rear cover bolt, it will not be re-used. 6. Loosen the brake rod at the rear eyelet using a T30 Torx driver. 7. Remove the exhaust mounting bar, saving the three mount bolts and washers for re-use. 8. Using snapring pliers, carefully remove the flanges and circlips from the stock exhaust system. Save for re-use. NOTE: If circlips look bent or twisted replace them with new circlips. VANCE & HINES EXHAUST SYSTEM INSTALLATION 1. Check condition of stock exhaust gaskets. Replace if damaged or worn. Vance & Hines recommends you replace your gaskets with Screamin’ Eagle gaskets part number 17048-98. 2. Install and tighten supplied mounting bracket (stamped 356-P) using stock bolts and washers (Figure 1). Torque to 30-33 Ft/Lbs. NOTE: Support the rear of the bracket during tightening to insure it is aligned with the bottom edge of the frame. 3. Re-install drive belt cover. Torque to 1 x 3/8″ bolt 30-33 Ft/Lbs. 2 x 1/4″ bolts 80-120 In/Lbs. 4. Re-install brake rod eyelet using blue thread locking compound (Loctite® 243). There is a 1/2″ clearance hole in the bracket to allow access for tightening brake rod eyelet. Torque to 120/180 In/Lbs. (Figure 1). 5. Remove header pipes and heat shields from protective packaging. Place each heat shield on a non-abrasive surface such as a blanket or carpet. Using a felt tip pen, mark outside edge of each heat shield to show location of mounting clips where hose clamps will loop through (Figure 2). 6. Install circlips and flanges from the stock system onto both new head pipes.

Incoming search terms:

2007 Harley Davidson Sportster 1200 Installation Manual

0

Filed Under (Harley Davidson) by admin on 11-04-2012

download
1 Remove the stock seat. 2 Unplug the stock wiring harness from the ECM (Fig. A) . 3 Remove the ECM from the tray and remove the tray from the fender. You can reach underneath the fender to gain access to the release tabs for the tray. 4 Install the Dynojet tray into the rear fender . Make sure that all 3 location tabs are underneath the fender. 5 Lay the PCIII in the tray (Fig. B). 6 Install the stock ECM on top of the PCIII making sure that it is secured by the tray locking tabs. 7 Plug the GREYconnector from the PCIII into the ECM. 8 Route the PCIII harness on top of the GREY connector (Fig. C) and route towards the front of the bike. Fig. A Fig. B Fig. C 2007 Harley Davidson Sport ster 1200 – PCIII USB – 2 i817-51 1 www .powercommander .com Unplug Tray 9 Plug the BLACK connector from the PCIII into the stock wiring harness. Secure this connection with one of the supplied zip ties (Fig. D). 10 Run a zip tie behind the wiring harness (Fig. E). 11 Route the stock wiring harness as shown in Fig. E. Due to the lack of room on this bike this step needs to be exact or the install will not fit properly . Make sure that the harness coming from the GREYconnector is flush against the battery box. Acouple inches of this harness will be tucked underneath the frame

HARLEY DAVIDSON SPORTSTER FORWARD CONTROL KITS REMOVAL AND INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 07-02-2011

download
Remove Stock Shift Lever and Footrest Assembly 1. See Figure 1. Loosen the shift lever retaining screw (2) securing the shift lever (1) to the shifter shaft. Slide the shift lever off the splined shaft. Remove shifter peg from lever and save for installation. Discard shift lever. 2. Remove the two socket head screws (4) securing the footrest bracket (3) to the frame and remove footrest. Discard screws. 3. See Figure 6. Obtain two hole plugs (1) from kit and firmly press plugs into frame screw holes remaining from footrest removal. 4. See Figure 2. Remove the retaining ring (1) from the clevis to free the footrest clevis pin (4). Remove the clevis pin and footrest (3) from the footrest support. Save footrest for installation. Discard retaining ring, clevis pin, spring washer and footrest bracket. 1 2 4 3 is03193 1. Shift lever 2. Retaining screw 3. Footrest bracket 4. Socket head screw (2) Figure 1. Remove Shift Lever and Footrest 5 1 3 2 4 is03194 1. Retaining ring 2. Spring washer 3. Footrest 4. Clevis pin 5. Footrest bracket Figure 2. Remove Left Footrest from Support Remove Stock Brake Pedal and Footrest Assembly 1. See Figure 3. At the right footrest, remove the retaining ring (1) clevis pin (2), footrest (3) and spring washer (4). Discard all hardware but save footrest for installation. 2. Remove the exhaust to access the brake rod. Follow the instructions in the appropriate Service Manual. 3. Remove brake rod (5) from brake pedal and master cylinder bell crank. Discard brake rod INSTALLATION Install Forward Control Brake Pedal and Footrest Assemblies 1. See Figure 5 and Figure 6. At the lower front of the right frame downtube, remove the two screws securing the J- clip (B) to the frame. Discard the screws but save J-clip for installation. 2. Install the other end of the brake rod into the brake pedal assembly (8). Tighten to 84-144 in-lbs (9.5-16.3 Nm) . NOTE Assemble the brake pedal and footpeg clevis onto the footrest support bracket (as described in the next step) prior to mounting the support bracket to the frame. This will allow easier installation of the footrest mount clevis retaining ring (installed to grooved end of footrest mount clevis). 3. Slide the brake pedal (8) onto footrest mount clevis (11) then slide clevis into footrest/brake pedal support bracket (9). Align hole in the clevis with hole in the support bracket and install screw (6). Tighten the screw to 18-22 ft-lbs (24.4-29.9 Nm) . 4. Install the footrest mount clevis retaining ring (18) to the groove at the end of the footpeg clevis. 5. Position the J-clip (from Step 1) against the frame aligning the mounting holes. Mount the footrest/brake pedal support bracket (9) and J-clip to frame using the new screws (3). Tighten the bracket to 45-50 ft-lbs (61.1- 67.9 Nm) . 6. Obtain the brake rod (15) from kit and thread one end into the master cylinder bell crank. Tighten to 120-180 in-lbs (13.6-20.3 Nm) . 7. Install footpeg on clevis with spring washer (2). Make sure spring washer is positioned inside clevis (11) with the square edge toward the inside. Align holes and push clevis pin (7) from top down through hole in clevis. Secure clevis pin using the new retaining ring (17). 8. Install exhaust following the instructions in the appropriate Service Manual. Install Forward Control Shift Lever Assembly

Incoming search terms:

HARLEY DAVIDSON DYNA AND SPORTSTER Chrome Front Wheel Spacers INSTALLATION ISNTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 29-01-2011

download
1. Block motorcycle underneath frame so front wheel is raised off the ground. 2. See Figure 1. Remove the upper (1) and lower (2) brake caliper mounting bolts and brake caliper(s) (3). Support caliper(s) using a rubber bungee cord. Be careful not to scratch fender paint. NOTES Do not operate front brake lever with the front wheel removed or the caliper piston may be forced out of piston bores. Reseating the piston requires disassembly of the caliper. Prior to removal, make note of existing left and right spacer location. The new spacers will be installed in the locations. 3. See Figure 3. On left side of wheel, remove axle nut (D), lockwasher (E) and washer (F). Perform the following: 4. Sportster and Dyna (except FXDWG) See Figure 2. Loosen the pinch bolt nut (1) and pull the the axle (2) free. Remove wheel and spacers. Leave bearing(s) in place. Discard spacers. 3 1 2 is04469 1. Brake caliper mounting bolt, long (top) 2. Brake caliper mounting bolt, short (bottom) 3. Brake caliper Figure 1. Caliper Mounting Bolts (Left Side) Dyna and Sportster 3 1 2 is04470 1. Pinch bolt nut 2. Axle 3. Pinch bolt Figure 2. Front Wheel Mounting (Dyna and Sportster Except FXDWG-Right Side) 5. See Figure 3. Obtain the new right (1) and left (2) chrome spacers from kit and install. 6. Apply a light coat of ANTI-SEIZE LUBRICANT (Harley- Davidson Part Number 98960-97) to the axle.
7. Place wheel between sliders and install axle. Verify that axle spacers on right and left side are properly installed. 8. See Figure 3. Install the washer (F), lockwasher (E) and nut (D) onto threaded end of axle (A). 9. In order to properly align the front fork, perform the fol- lowing: a. On the right side of the wheel, insert a 7/16 inch drill bit through the hole in the axle. While holding axle stationary, tighten axle nut to 50-55 ft-lbs (61.0-74.6 Nm) . b. Pull fork leg so that it just contacts drill bit. Tighten according to the following: c. Refer to Figure 2. Tighten the Axle Pinch Bolt Nut to 25-30 ft-lbs (33.9-40.7 Nm) . d. Remove drill bit from axle hole. 10. Follow instructions in Service Manual and install brake caliper to the sliders noting the following: •Loosely install long bolt to the top hole on fork leg. Install the short mounting bolt to the bottom hole and tighten to 28-38 ft-lb (38.0-51.5 Nm) . •Final tighten top bolt to 28-38 ft-lbs (38.0-51.5 Nm) . 11. Repeat Step 10 to install brake caliper on opposite side of wheel. After servicing brakes and before moving motorcycle, pump brakes to build brake system pressure. Insufficient pressure can adversely affect brake performance, which could result in death or serious injury. (00279a) 12. Pump brake lever to move pistons out until they contact both brake pads. Verify piston location against pads

Incoming search terms:

Harley davidson Sportster Custom Straightshot Exhaust System REMOVAL AND INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 19-12-2010

download
REMOVING THE STOCK EXHAUST SYSTEM 1. Loosen the heat shield clamps on both front and rear exhaust pipes. 2. Remove the two mounting nuts from each head pipe, located at the cylinder head. 3. Remove the nut that mounts the front muffler to the engine, located below the rear brake master cylinder. 4. Remove the bolt that mounts the rear muffler to the mounting bar. 5. Remove the entire exhaust system and set it aside. 6. Carefully remove the flanges and circlips from the stock exhaust system using snapring pliers. Note: If circlips look bent or twisted replace them with new circlips . INSTALLING YOUR NEW VANCE & HINES EXHAUST SYSTEM 1. Vance and Hines recommends you replace your exhaust gaskets with Sceamin’ Eagle gaskets part number 17048-98. 2. Install the circlips and flanges from the stock system on to both of the new head pipes. 3. Unscrew all of the hose clamps (supplied) until they are completely loose. Mark the top edge of both heat shields with the location of the mounting clips that are welded to the backside. Position the front heat shield over the head pipe and feed the tail end of the hose clamps into the clips. Be sure that each hose clamp is engaged with both clips. Repeat this step with the rear heat shield. Note: The screw end of the hose clamp should be accessible, but not visible when pipe is mounted on the bike. 4. Install the front head pipe using the stock nuts, do not tighten at this time. 5. Install the rear head pipe using the stock nuts, do not tighten at this time. 6. Install one muffler clamp (supplied) over the inlet (notched end) of each muffler. 7. Identify the front and rear muffler mounting brackets. The front bracket is stamped with the number 305 and the rear muffler bracket is stamped 213 . 8. Install the front muffler mounting bracket to the stud on the engine (where the stock muffler mounted) and fasten using the stock nut (leave loose at this time). The bracket will bend inward towards the center of the motorcycle when installed correctly. Note: You may need to move the wires and hoses on the lower frame rail to decrease the possibility of them chaffing on the bracket bolts. 9. Slip one of the mufflers onto the front head pipe. Slide one dog bone shaped nut plate (supplied) under the bracket that is welded to the backside of the muffler. Attach the muffler to the mounting bracket using the 5/16″ flange head bolts (supplied) leave them loose at this time. 10. Attach the rear mounting bracket to the rear muffler. Slide one dog bone shaped nut plate (supplied) under the bracket that is welded to the backside of the muffler. Attach the bracket to the muffler using two of the 5/16″ flange head bolts (supplied), leave them loose at this time. Note: The single hole in the bracket will point downward and slightly forward when installed correctly

TOYOTA COROLLA 1984-2006 VEHICLE WIRING VEHICLE WIRING REMOVAL

0

Filed Under (Toyota Manuals) by admin on 04-10-2011

download
IRING INFORMATION: 1984 Toyota Corolla FWD WIRE WIRE COLOR WIRE LOCATION 12V CONSTANT WIRE WHITE OR WHITE/RED Ignition Harness STARTER WIRE BLACK/WHITE Ignition Harness IGNITION WIRE BLACK/YELLOW Ignition Harness SECOND IGNITION WIRE BLACK/ORANGE Ignition Harness ACCESSORY WIRE BLUE/RED Ignition Harness POWER DOOR LOCK (-) BLUE/WHITE Harness In Driver’s Kick Panel POWER DOOR UNLOCK (-) BLUE/RED Harness In Driver’s Kick Panel PARKING LIGHTS (+) DK. GREEN Harness In Driver’s Kick Panel PARKING LIGHTS (-) LT. GREEN Harness At Steering Column HEADLIGHTS (-) RED/WHITE Harness At Steering Column DOOR TRIGGER (-) RED/WHT OR BLK/WHT Harness At Fuse Box TRUNK TRIGGER COMMON WITH DOORS (Hatchback Only) TACHOMETER WIRE BLACK At Ignition Coil BRAKE WIRE (+) GREEN/WHITE Brake Pedal Switch HORN TRIGGER (-) GREEN/RED Steering Column LEFT FRONT WINDOW UP GREEN/BLACK At Driver Window Motor Inside Door LEFT FRONT WINDOW DOWN BLUE/RED At Driver Window Motor Inside Door RIGHT FRONT WINDOW UP GREEN Harness In Driver’s Kick From Driver Door RIGHT FRONT WINDOW DOWN BLUE/WHITE Harness In Driver’s Kick From Driver Door LEFT REAR WINDOW UP RED/BLACK Harness In Driver’s Kick From Driver Door LEFT REAR WINDOW DOWN RED/YELLOW Harness In Driver’s Kick From Driver Door RIGHT REAR WINDOW UP RED/BLUE Harness In Driver’s Kick From Driver Door RIGHT REAR WINDOW DOWN BLUE/BLACK Harness In Driver’s Kick From Driver Doo

Incoming search terms:

HARLEY DAVIDSON BILLET HEADLAMP WITH SHORT/ TALL MOUNTS REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 06-03-2011

download
Kit 68593-06 is a 5-3/4 inch headlamp and kit 69851-06 is a 4-1/2 inch headlamp. Both kits will fit the models listed in Table 1. Table 1. Short and Tall Mount Kits Models Kits 1984-1999 FXSTC, 1998- Later FXST/B, and 2000-Later FXSTD; 1994-2005 FXDWG Short Mount Kit 68595-06 1996-Later XL 1200C and 1998-Later XL 883C; All 2006 Dyna Models; 1999-2000 FXR2/3/4 Tall Mount Kit 69611-06 Additional Parts Required This kit also requires the separate purchase of a Short or Tall Mounting Kit 68595-06 or 69611-06 for your model motorcycle, and can be purchased from a Harley-Davidson dealer. The rider’s safety depends upon the correct installation of this kit. Use the appropriate service manual procedures. If the procedure is not within your capabilities or you do not have the correct tools, have a Harley-Davidson dealer perform the installation. Improper installation of this kit could result in death or serious injury. (00333a) NOTE This instruction sheet references Service Manual information. A Service Manual for your model motorcycle is required for this installation and is available from a Harley-Davidson dealer. Kit Contents See Figure 21, Table 2 and Figure 22, Table 3. REMOVAL Remove Headlamp and Mounting Bracket for Softail Models To prevent accidental vehicle start-up, which could cause death or serious injury, disconnect negative (-) battery cable before proceeding. (00048a) 1. Disconnect negative (-) battery cable. 2. Remove fuel tank. Refer to FUEL TANK in Service Manual. 3. Disconnect 4-place headlamp connector [38] from main wire harness. Headlamp connector is located under fuel tank on left side. 8 5 7 5 6 2 1 3 4 is01835 1. Screw 2. Washer 3. Nut 4. Lockwasher 5. Washer (2) 6. Screw 7. Mounting block 8. Headlamp assembly Figure 1. Softail and Dyna Headlamp Assembly with Mount (except FXSTD) NOTE All Softails (except FXSTD) complete steps 4 through 6. For FXSTD models complete steps 7 through 9 4. All Softails (except FXSTD): See Figure 1. Remove screw (1) and washer (2) from stem and bracket. Discard screw but save washer for later use. 5. Remove and discard mounting block (7) and headlamp assembly (8). 6. FXSTD models: See Figure 2. Remove screw (1) and washer (2) from stem and bracket. Save screw and washer for later use. 7. Remove and discard nut (3), washers (4), and screw (5). 8. Remove and discard mounting block (6) and headlamp assembly (7). 7 3 4 2 1 4 6 5 is01838 1. Screw 2. Washer 3. Acorn nut 4. Washer (2) 5. Screw 6. Mounting block 7. Headlamp assembly Figure 2. FXSTD Headlamp Assembly with Mount Remove Headlamp and Mounting Bracket for Dyna Models 1. Remove seat following the instructions in the Service Manual. 2. Disconnect negative (-) battery cable. 3. Remove fuel tank. Refer to FUEL TANK in Service Manual. 2 1 is01750 1. Cable strap 2. Wire harness Figure 3. Dyna Service Loop (2005-Earlier) 4. 2005-Earlier FXDWG: See Figures 3 and 4. Remove plug on right side of top frame tube. At service loop, remove cable clip and push wire harness into top frame tube. Pull connector out from hole on right side of tube. 2006-Later FXD: See Figure 5. Remove cover under top frame tube, then pull connector out from opening under tube. 5. Disconnect 4-place headlamp connector [38] from main wire harness

Incoming search terms:

HARLEY DAVIDSON LOCKING FUEL FILLER CAP KIT REMOVAL AND INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 11-02-2011

download
INSTALLATION 1. Prior to installing the gas cap on the vehicle, insert the key into the lock. Firmly grasp the chrome top of the fuel cap and turn the key until it stops. On right hand threaded fuel caps, turn the key counter-clockwise until it stops. On left hand threaded fuel caps, turn the key clockwise until it stops. This assures an unlocked position for the gas cap. Allow the key to return to the neutral position. 2. Remove the key and install the fuel cap on the vehicle. is00770 Figure 1. Right Hand Threaded Fuel Cap Installation NOTE When installing the fuel cap, rotate the cap one full turn past the audible click. This automatically positions gas cap to lock position. A properly locked/installed gas cap will rotate freely in both directions. Failure to do so will give an incorrect assumption that the fuel cap does not work properly. REMOVAL On right hand threaded fuel caps, insert key, and while holding the gas cap in place with hand, turn key counterclockwise until it stops, return key to original position. Gas cap must rotate 270 degrees counter-clockwise before mechanism engages to allow gas cap removal. Continue to rotate counterclockwise to fully remove gas cap. On left hand threaded fuel caps, insert key and while holding the gas cap in place with hand, turn key clockwise until it stops, return key to original position. Gas cap must rotate 270 degrees clockwise before mechanism engages to allow gas cap removal. Continue to rotate clockwise to fully remove gas cap. REPLACEMENT KEYS Record the 4 digit key number stamped on the back of the key opposite the Harley-Davidson logo, in the area provided below. If a replacement key is needed, see your Harley-Davidson Dealer with the 4 digit number to order a replacement

Incoming search terms:

HARLEY DAVIDSON BLACK ENGINE GUARD KIT REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 24-02-2011

download
REMOVAL NOTE This Instruction Sheet covers several different Harley-Davidson models and years. Be sure to locate and follow the procedures that apply to the motorcycle receiving the new guard. For Models without Lower Fairings 1. Proceed to For All Models section. For Model FLHTCUI (Ultra Classic Electra Glide) with Factory-Installed Lower Fairings 1. Remove the lower fairings following the instructions in the appropriate Service Manual. 2. When the lower fairings have been removed, proceed to For All Models section. For Models FLHR/I (Road King), FLHT (Electra Glide Standard) or FLHTC/I (Electra Glide Classic) with Harley-Davidson Genuine Motor Accessory Lower Fairings 1. See Figure 1. Remove the two black screws (1) that attach the fairing cap (2) to the lower fairing (5). Remove the cap. Set the parts aside for re-installation. 2. Remove the screw (7), rubber washer (8) and locknut (10) and the clamp (9) that attaches the bottom of the lower fairing to the engine guard and set aside. 3. Remove the two locknuts (3), U-bolt (6) and U-bolt retainer (4). 4. Remove the lower fairing by sliding it out from behind the engine guard. 5. Repeat Steps 1 through 4 for the opposite side. 6. Proceed to For All Models section. For Model FLTR/I (Road Glide) with Harley-Davidson Genuine Motor Accessory Lower Fairings Disconnect negative (-) battery cable first. If positive (+) cable should contact ground with negative (-) cable connected, the resulting sparks can cause a battery explosion, which could result in death or serious injury. (00049a) 1. Disconnect the battery, negative (-) battery cable first, following the instructions in the appropriate Service Manual. 2. Remove the seat following the instructions in the appropriate Service Manual. 3. Remove the cable strap holding the clutch cable to the engine guard. 4. See Figure 2. Remove the TORX screw (8), rubber washer (9) and locknut (11) and the clamp (10) that attaches the bottom of the lower fairing (4) to the engine guard and set aside INSTALLATION 1. Hold the engine guard in position, and loosely fasten the top of the guard with the new hex socket screw and flat washer from the kit. 2. Install the bottom brackets to the motorcycle frame with the two new TORX screws and locknuts. 3. Tighten all three screws to 15-20 ft-lbs (20.3-27.1 Nm) . For Model FLHTCUI (Ultra Classic Electra Glide) with Factory-Installed Lower Fairings 1. Install the lower fairings following the instructions in the appropriate Service Manual. For Models FLHR/I (Road King), FLHT (Electra Glide Standard) or FLHTC/I (Electra Glide Classic) with Harley- Davidson Genuine Motor Accessory Lower Fairings 1. Carefully place one lower fairing in position from behind the engine guard. 2. See Figure 1. Install the lower fairing to the top of the new engine guard with the U-bolt (6) from the back, through the holes at the top of the fairing. Install the retainer (4) in position on the U-bolt and secure to the engine guard with the two locknuts (3). Do not tighten the locknuts at this time. 3. Attach the bottom of the fairing to the engine guard with the clamp (9) removed earlier. Install the clamp around the engine guard in the direction shown, with the tabs toward the rear of the vehicle and the flat side of the clamp against the lower fairing. Insert the screw (7) through the lower fairing, rubber washer (8) and clamp (9). Secure the assembly with the locknut (10). Tighten to 12 ft-lbs (16.3 Nm) .

Incoming search terms:

Incoming search terms: