2011 kawasaki vaquero replacement gas tank

You search Auto repair manual PDF 2011 kawasaki vaquero replacement gas tank, if there are search results will appear below. If search results do not exist, please search by others keyword.



  2011 kawasaki vaquero replacement gas tank Direct Download speed 5282 Kb/s

  2011 kawasaki vaquero replacement gas tank Full Version speed 6162 Kb/s



HARLEY DAVIDSON FLUSH-MOUNT LED FUEL GAUGE AND GAS CAP KIT INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 29-01-2011

download
1. Remove stock gas cap from fuel tank. 2. Clean and wipe inside surface of fuel tank filler cup, O-ring seal surface, and trim ring adhesive surface with a mixture of equal parts of isopropyl alcohol and distilled water. 3. See Figure 1. Install gas cap into fuel tank. is00407 Figure 1. Screw in Gas Cap is00466 Figure 2. Note Position of Arrow on Trim Ring 4. Push down on gas cap and rotate clockwise one-eighth of a turn to lock. To unlock, push down on gas cap and rotate counterclockwise one-eighth of a turn. 5. See Figure 2. Before removing adhesive backing, note position of arrow on inside diameter of chrome trim ring. NOTE As you rotate trim ring, you will see gaps between trim ring and fuel tank. Rotate trim ring to position that best eliminates gaps between fuel tank and trim ring. Rotation of trim ring should be minimal. 6. See Figure 3. With the arrow pointing toward front of motorcycle, rotate chrome trim ring slightly to determine best position of bottom chrome trim ring to contour of the fuel tank 7. See Figure 4. Mark position of chrome trim ring with masking tape or grease pencil. 8. Carefully cut masking tape with a hobby knife making sure not to scratch chrome trim ring or paint surface on fuel tank. 9. Peel off adhesive backing from chrome trim ring. 10. Using gas cap to center and masking tape (or grease pencil mark) to align, press chrome trim ring firmly into position for about ten seconds. 11. Peel off masking tape (or remove grease pencil mark) from chrome trim ring and fuel tank. 2 1 is00414a 1. Masking tape 2. Cut masking tape Figure 4. Align Trim Ring and Press into Place NOTE Allow adhesive trim ring to cure for about 5-7 minutes before you continue with kit installation. Install Flush-Mount LED Fuel Gauge 1. Remove the seat following the instructions in the service manual. Disconnect negative (-) battery cable first. If positive (+) cable should contact ground with negative (-) cable connected, the resulting sparks can cause a battery explosion, which could result in death or serious injury. (00049a) To prevent accidental vehicle start-up, which could cause death or serious injury, disconnect battery cables (negative (-) cable first) before proceeding. (00307a) 2. Disconnect battery cables, negative (-) cable first. 3. Remove stock fuel gauge. Refer to service manual for instructions. 4. Insert wires down tube of fuel tank from LED fuel gauge. 5. See Figure 5 and Figure 6. Insert LED fuel gauge in the fuel tank cup

HARLEY DAVIDSON CHROME FUEL TANK TRIM PANEL INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 25-02-2011

download
INSTALLATION 1. Refer to the Owner’s Manual and follow the instructions given to remove the seat. Retain all seat mounting hard- ware. Stop the engine when refueling or servicing the fuel system. Do not smoke or allow open flame or sparks near gasoline. Gasoline is extremely flammable and highly explosive, which could result in death or serious injury. (00002a) 2. See the Figure 5. Remove the original fuel filler cap (A) from the tank and set it aside. Obtain a small diameter Harley-Davidson fuel filler cap (B) and screw it into the fuel filler opening. For Model XL883C, or other models equipped with Genuine Motor Parts Large Capacity Fuel Tank 3. To ensure surface cleanliness, clean the top of the fuel tank with a mixture of 50 to 70% isopropyl alcohol and 30 to 50% distilled water. Allow to dry thoroughly. 4. Measure and mark the centerline of the fuel tank, with a wax pencil or water-based marker, at the rear of the tank as shown in Figure 3. Proceed to Step 10. For Model XL1200C 2 1 is 01910 1. Original fuel tank trim panel liner 2. Fishing line (or string) Figure 1. Removing the Existing Trim Panel (XL 1200C) 5. See Figure 1. Insert the fishing line (2) between the rear of the fuel tank and the liner (1) on the underside of the original trim panel. NOTE Raise the ends of the fishing line away from the fuel tank to avoid scuffing the tank finish 6. Using a side-to-side “sawing” motion, work the fishing line toward the front of the fuel tank to break the adhesive bond between the trim panel and the tank. 7. Carefully pull the trim panel and liner off of the tank and discard it. NOTE Be careful not to scratch the paint on the fuel tank when removing the adhesive

BUELL ACCESSORY GAS CAP KIT INSTALLATION MANUAL

0

Filed Under (Buell) by admin on 29-03-2011

download
Installation NOTE When performing the following Steps, use the Fuel Tank Vent Valve Installation Kit (Part Number 91432-96Y). This kit consists of: * Fuel Tank Vent Valve Installation Aid * Fuel Tank Vent Valve Fitting Socket To protect against shock and accidental start-up of vehicle, disconnect the battery cables, negative cable first, before proceeding. Inadequate safety precautions could result in death or serious injury. Always disconnect the negative battery cable first. If the positive battery cable should contact ground with the negative cable installed, the resulting sparks may cause a battery explosion which could result in death or serious injury. 1. Disconnect battery cables, negative cable first. An open flame or spark may cause a fuel tank explosion if all traces of fuel are not purged from the tank. Use extreme caution when servicing fuel tanks. Gasoline is extremely flammable and highly explosive. Do not smoke or allow open flame or sparks anywhere in the area when working on fuel system components. Inadequate safety precautions could result in death or serious injury. 2. Remove gas cap. 3. Carbureted Models: Drain fuel tank. Disconnect hose clamp and fuel supply hose from fuel supply valve and drain fuel into suitable, clean container. See applicable Service Manual, Section 4 for complete, detailed procedure. Fuel Injected Models: Relieve pressure from fuel system. See applicable Service Manual, Section 4 for complete, detailed procedure. Drain fuel tank. a. Using suitable external fuel pump, such as a Gas Caddy, pump fuel from tank and into a suitable, clean container. b. See instructions for external fuel pump for correct use. 4. See Figure 1. Cut cable tie securing vent hose to fitting and remove vent hose from fuel tank. Even with the fuel tank completely drained, a small amount of gasoline may leak from the bore when the fuel supply valve is loosened or removed. Thoroughly wipe up any fuel immediately and dispose of rags in a suitable manner. Gasoline is extremely flammable and highly explosive. Inadequate safety precautions could result in death or serious injury. 5. If the fuel supply valve requires cleaning or repair, refer to applicable Service Manual, Section 4, for complete, detailed procedures. 6. See Figure 1. Remove the fuel filler cap and O-ring. 7. Remove the eight self-tapping screws from fuel clamp flange and remove fuel cap flange

2000-2002 Aprilia Mille INSTALLATION INSTRUCTIONS

0

Filed Under (Aprilia) by admin on 26-10-2010

download
1) It is a good idea to use Blue Loc-tite on all bolts you are about to remove and replace. 2) This kit has extremely close tolerances and in order for all the parts to clear the triple clamp and gas tank, you will probably have to loosen and align most of the associated bolts. We have tried very hard to make this as compact as possible but we know the factory tolerances vary from bike to bike. Be patient, the results are worth it. 3) Remove both front fuel-tank retaining bolts. You will use the longer bolts provided in our kit. 4) Install the frame bracket (part #22-6036-03) that mounts to your front (2) tank bolts holes. The frame bracket sits on top of the stock tank spacers. The frame bracket is offset. This means it fits correctly only one way, with the offset toward the triple clamp, part numbers facing forward, (see photo below). Due to the tight clearances on this model you’ll want to be sure the frame bracket does not make contact with the tank itself. It’s easier to start the tank bolts if you lift up on the tank slightly, while starting the new bolts into their threaded hole. Tighten the new tank bolts to 6 ft lbs. and use Loc-tite. 5) Remove the large 14mm Allen nut and washer that holds your triple clamp on. You will not re-use either one. 6) Install the new “Triple clamp damper mount” Part # 22-2925-00 into the recess area where the stock Allen head bolt was sitting. There is a machined recess or built-in-washer on the bottom of our mount to match the recess on your triple clamp. The 2 nubs that hang down, should match the rear contour of your triple clamp precisely. Use loc-tite and retighten the new 14mm Allen nut provided to your factory torque specs, usually a minimum of 35 ft lbs. and maximum of 85 ft. lbs. Do not use the stock washer that was under the original 14mm nut. 7) Grease the tower pin and drop it in the tower pin hole portion of the frame bracket. The tower pin is designed to “float” and requires no retaining devices. Keep the tower pin lightly greased! It should not touch the gas tank on the bottom side. 8) Install the stabilizer using the (2) 6×20 Allens with the slot in the link arm matching the tower pin. 9) Since the tank is rubber mounted at the rear, you want to be sure it won’t push forward and rub the frame bracket. After riding the first time, be sure the tank has not shoved forward by your body making contact with it. Remember, under heavy braking your entire body weight is pushing the tank forward. Until you have verified sufficient clearance between the tank and the tower pin, it might be smart to put something between the tank and tower pin to protect the tank. 10) Read your damper manual for initial settings on the controls. The damper is infinitely adjustable and totally up to the user to find their preference. Start with softer (counter clockwise) settings. Normally where we set the unit, at 8 clicks out on the base valve, is a good starting point.

BMW Motorcycles F 650 GS Dakar fuel tank replacement

0

Filed Under (BMW) by admin on 12-11-2010

download
Your center has been requested in a recent e-mail, to forward VIN, color Information: and status information on all F 650 GS(A) and Dakar models remaining in your inventory. Fuel tanks, together with the appropriate colored trim pieces, will be forwarded to your center for each bike in your inventory as replacement parts arrive in BMW NA inventory. Warranty Please enter a warranty campaign claim , encompassing the following Reimbursement: Work Package information, when claiming reimbursement for the updates called for in this bulletin. Even though there is no charge for the parts, a sublet of $60.00 will be applied to each claim. This sublet amount is intended as a combination of both the handling and as reimbursement for incidental items that may be required in the replacement of the fuel tank. Work Package #1 is to be used in the replacement of all F 650 GS(A) and Dakar model fuel tanks. Defect Code: 00 00 16 1100 Description: Fuel Tank – Leaking Flat Rate Code: 00 60 059 Description: Remove and reinstall fuel tank (USA only) FRU: 12 FRU Sublet #4: $60.00 Pick up & In the recent Sales and Marketing Bulletin # B23/00 introducing the “Customer Delivery: Demonstration Program”, (e-mailed to your center on September 7, 2000), each BMW motorcycle retailer was asked to arrange to pick up, complete the updates and deliver the motorcycle back to the customer and to offer the use of a demonstrator where appropriate.

Related Item : dakar fuel tanks (1)kawasaki prairie 650 replacement plastic (1)kawasaki w800 tires (1)