2012 zx14r slip on muzzy exhaust for sale

You search Auto repair manual PDF 2012 zx14r slip on muzzy exhaust for sale, if there are search results will appear below. If search results do not exist, please search by others keyword.



  2012 zx14r slip on muzzy exhaust for sale Direct Download speed 5282 Kb/s

  2012 zx14r slip on muzzy exhaust for sale Full Version speed 6162 Kb/s



Kawasaki Exhausts – ZX-6 ZX-10 Zx-14 Exhaust – Slip-ons INSTALLATION MANUAL

0

Filed Under (Kawasaki) by admin on 25-10-2010

download
Our favorite exhaust options for Kawasaki ZX Ninjas – ZX-10,ZX-6r, and the new horsepower king, Zx-14.. Grab your horsepower today. We love Rob Muzzy and Muzzy Exhausts.Going back to Doug Chandler and Scott Russell, Muzzy has been synonomous with Kawasaki and performance – and for years, if you rode Kawasaki,and you were on the podium, Muzzy was on your exhaust. We also feature Arrow and Yoshimura exhausts for your ZX-6R, ZX-10 and ZX-14. We love the sound of a Yosh exhaust on any Kawasaki Ninja. Yoshimura Oval (RS-3) Race Slip-On for Kawasaki ZX14R 2006 The easiest and least expensive way to experience Yoshimura performance is with our Slip-On/Bolt-On lines. Bolt-On style bolts to the O. E. M. mid-pipe Slip-On style with its stainless steel easily attaches to the mid-pipe RS-1 is available where noted Usually, no jetting or re-programming is required and installation is a snap Hindle Stainless Exhaust High Head Pipes – Kawasaki ZX6R-RR 03-04 The worlds lightest stainless steel exhaust system. Increase horsepower and torque throughout the entire rpm range. Lightweight, strong stainless steel header design looks great and weighs less than stock headers. Available in low- and high-mo North Denver News http://northdenvernews.com Powered by Joomla! Generated: 19 October, 2010, 12:28 Hindle Stainless Exhaust Low Head Pipes – Kawasaki ZX9R 00-03 The worlds lightest stainless steel exhaust system. Increase horsepower and torque throughout the entire rpm range. Lightweight, strong stainless steel header design looks great and weighs less than stock headers. Available in low- and high-mo

Incoming search terms:

SUZUKI M109 1800 cc EXHAUST SYSTEM INSTALLATION MANUAL

0

Filed Under (Suzuki) by admin on 10-11-2010

download
1. Remove the seat and right side fairing cover (with M109 insignia), behind the fuel tank. To remove the fairing, release the plastic peg on top by pushing the center inward and pulling the fairing upwards until the peg releases, remove the M6 button head bolt at the bottom of the fairing. Pull the fairing outward from the rear and upward near the plastic peg to release it. Once it is free from all plastic pegs pull it forward to release it from the bottom of the fuel tank. 2. Remove the right side cover above the exhaust-mounting bracket secured by one M6 button head bolt, retain bolt for later. Remove the chrome steel cover above the exhaust secured by two remaining bolts, (this chrome piece will no longer be used.) Remove the large left rear rubber grommet and flanged steel collar from this chrome piece, to do this press the steel collar out of the rubber grommet first, once the collar is removed push the rubber grommet out of the wire loop on the chrome piece, set aside for later use. 3. Locate the exhaust valve actuator solenoid and harness and disconnect the black 3-prong electrical connector and white 2-prong electrical connector. 4. Remove the socket head bolts securing exhaust flanges to cylinder heads, set these fasteners aside for later use in reassembly. Support the weight of the exhaust system and remove the 2, 8 mm bolts and one 8 mm nut securing the exhaust mounting bracket and exhaust assembly. Keep these fasteners for use later. Remove the stock exhaust system as one complete unit; this includes the stock exhaust bracket, headpipes and muffler, exhaust valve solenoid and cables. 5. The exhaust valve actuator solenoid must now be removed from the stock exhaust-mounting bracket. To perform this, loosen the two nuts securing each cable to the exhaust valve cable-mounting tab, Position A in Figure 1. Make enough slack in the cables so that the ends of the cables’ threaded sheath may be disengaged from the end of the mounting tab. Now remove the two M6 hex head bolts securing the solenoid to the stock exhaust bracket. The stock exhaust mounting bracket, headpipes and muffler and exhaust valve solenoid cables will not be used anymore with the your new Cobra Exhaust System. 6. Remove the dust cover from the solenoid to expose the rotating cam and cables. DO NOT TRY TO ROTATE THE CAM RELATIVE TO THE ACTUATOR SELENOID TO REMOVE THE CABLES; DOING SO MAY DAMAGE THE INTERNAL COMPONENTS OF THE SOLENOID. To remove the cables from the cam, use the slack in the cables obtained in Step 5 to disengage the cable barrels from the cam, see Figure 1. THE DUST COVER WILL NOT BE REINSTALLED. 7. Now prepare the exhaust valve actuator solenoid for reuse. SECURELY HOLD THE CAM TO PREVENT IT FROM ROTATING IN THE SOLENOID. WHILE PREVENTING THE CAM FROM ROTATING, remove the 10 – 32 flange bolt securing it, see Figure 2. Replace the cam with the Cobra supplied cam, BE SURE TO PREVENT THE CAM FROM ROTATING WHEN REINSTALLING THE BOLT, OTHERWISE DAMAGE MAY OCCUR TO THE SOLENOID , see Figure 3. Torque to factory specifications.

Incoming search terms:

SUZUKI M109 1800 cc FRONT/REAR EXHAUST / HEATSHIELD INSTALLATION MANUAL

0

Filed Under (Suzuki) by admin on 15-11-2010

download
1. Remove the seat and right side fairing cover (with M109 insignia), behind the fuel tank. To remove the fairing, release the plastic peg on top by pushing the center inward and pulling the fairing upwards until the peg releases, remove the M6 button head bolt at the bottom of the fairing. Pull the fairing outward from the rear and upward near the plastic peg to release it. Once it is free from all plastic pegs pull it forward to release it from the bottom of the fuel tank. 2. Remove the right side cover above the exhaust-mounting bracket secured by one M6 button head bolt, retain bolt for later. Remove the chrome steel cover above the exhaust secured by two remaining bolts, (this chrome piece will no longer be used.) Remove the large left rear rubber grommet and flanged steel collar from this chrome piece, to do this press the steel collar out of the rubber grommet first, once the collar is removed push the rubber grommet out of the wire loop on the chrome piece, set collar and grommet aside for later use. 3. Locate the exhaust valve actuator solenoid and harness and disconnect the black 3-prong electrical connector and white 2-prong electrical connector. 4. Remove the socket head bolts securing exhaust flanges to cylinder heads, set these fasteners aside for later use in reassembly. Support the weight of the exhaust system and remove the 2, 8 mm bolts and one 8 mm nut securing the exhaust mounting bracket and exhaust assembly. Keep these fasteners for use later. Remove the stock exhaust system as one complete unit; this includes the stock exhaust bracket, headpipes and muffler, exhaust valve actuator solenoid and cables. 5. The exhaust valve actuator solenoid must now be removed from the stock exhaust-mounting bracket. To perform this, loosen the two nuts securing each cable to the exhaust valve cable-mounting tab, Position A in Figure 1. Make enough slack in the cables so that the ends of the cables’ threaded sheath may be disengaged from the end of the mounting tab. Now remove the two M6 hex head bolts securing the solenoid to the stock exhaust bracket. The stock exhaust mounting bracket, headpipes and muffler and exhaust valve solenoid cables will not be used anymore with the your new Cobra Exhaust System

Incoming search terms:

2009 APRILIA RSV4 SLIP-ON STREET LEGAL EXHAUST SYSTEM

0

Filed Under (Aprilia) by admin on 06-11-2010

download
Our sporty and lightweight SLIP-ON systems offer a great balance between price and performance and represent the first step in the exhaust system tuning process. The change will also be visual as our HEXAGONAL muffler perfectly fit the exterior line of the RSV4 and add a clean racing image. The muffler outer sleeve is made of titanium or carbon-fiber, which gives a special hi-tech touch to our SLIP-ON system. We offer the street legal version with high flow catalytic converter and open system for race track use only. PERFORMANCE Measurements of the Akrapovic SLIP-ON STREET LEGAL/OPEN system on the APRILIA RSV4 (without muffler insert): Power & Torque: the exhaust system modification with the SLIP-ON system results in a major boost in performance, delivering a massive 167.9 HP at 12450 rpm on the back wheel. But the increased power isn’t available just at the top of the range; the system shows its quality from 4000 rpm already up through the entire rpm range. Max. increased power between the Akrapovic and the stock system is 5.2 HP at 7000 rpm. Besides this, the torque is substantially higher in a lower rpm area at 4500 rpm and from middle to high rpm area. Technical specifications of Akrapovic exhaust systems and related products subject to change without notice. 50 75 100 125 150 75 80 85 90 95 100 105 110 4000 5000 6000 7000 8000 9000 10000 11000 12000 13000 WhlPwr EngT rq EngSpd RPM STOCK EXHAUST AKRAPOVIC SLIP-ON EXHAUST PERFORMANCE stock AKRAPOVIC max. increased power max. rear wheel power HP / rpm (measured on Dynojet ATV) 165 / 12400 167.9 / 12450 5.2 / 7000 noise measurements (dB / rpm) stock AKRAPOVIC 102 / 6200 102 / 6200 legal for street use NO / YES (Street legal exhaust

Incoming search terms:

BMW F650GS / F800GS Slip-On Exhaust System with M-2 Exhaust Canister Installation Instructions

0

Filed Under (Yamaha) by admin on 09-11-2010

download
1. Make sure the bike is completely cool before starting the installation. Make sure the bike is secure on a centerstand or ideally a service lift. 2. Remove muffler joint springs, set aside to re-use later. 3. Remove muffler mounting bolt and decorative washer, set aside to re-use washer later. 4. Attach TBR slip tube to TBR muffler using the 2 piece X-Rings and 6x14mm socket head cap screws with lock washer that are provided. Leave loose enough to make some adjustments on the motorcycle. 5. Attach muffler assembly to motorcycle using the OEM springs and supllied muffler clamp. Use the supplied 8x20mm socket head cap screw and OEM washer to secure muffler clamp. *a small amount of high temp silicone on slip joint may be used. 6. Align muffler and tighten the 4 X-Ring bolts. 7. Double check your work to ensure everything is tight and properly installed. 8. Before you run the bike, clean off all fingerprints and dirt, as any oily residue will etch the metal and become somewhat permanent when the system gets hot. Run the bike and enjoy. It is normal for some white smoke to appear the first time you start the bike. This is packing/ manufacturing oil from inside the pipe burning off. Check for gaps or leaks. If you find a leak, a little high temperature silicon sealant should fix it. After 50 to 100 miles, recheck all fasteners for tightness. 2008-09 BMW F650GS / F800GS V.A.L.E.™ Slip-On Exhaust System with M-2 Exhaust Canister Part # 005-2630406V / 005-2630407V / 005-2630408V Qty. Description Part Number 1 M-2 Muffler Canister Varies 1 Slip-On Tube Assembly 005-26304S 1 Muffler Clamp Varies 1 HARDWARE KIT 005-263-3 2 X-Ring (half) 005-7-2-3 4 6x14mm Socket Head Cap Screw 005-SH614 4 6mm Split Washer 005-WL6 1 8×20 Sockey Head Cap Screw

Incoming search terms:

KAWASAKI ZX-10R Carbon Fiber/ Aluminum Slip-On System Installation Manual

0

Filed Under (Kawasaki) by admin on 25-10-2010

download
After bike is cool make sure the bike is secured before beginning the installation. 2 Remove the rear exhaust heat shield/cover from the OEM muffler. Remove the side fairing covers on both sides of the bike (this will allow you access to the seat bolts). Remove the rider seat. 3 Remove the exhaust valve cables located under the seat. Keep the servo motor plugged in (do not unplug the server motor). See figure 2. 4 Unbolt the rear foot peg muffler mount, loosen the assembly mount (header collector clamp) and unbolt the exhaust mounting bolt (figure 3). Remove the stock muffler assembly with the exhaust valve cables. Re-install the seat, seat bolts, and side fairings. 5 Apply a small amount of high temperature silicone (such as Permatex Ultra Black) to the inside of the exhaust inlet. 6 Attach the LOR exhaust canister to the slip-on tube adapter with the spring tabs aligned (make sure your hands are protected with a pair of gloves in case the tubes slip). You may have to squeeze the mid-pipe adapter tube to fit into the exhaust inlet as the mandrel bends may become slightly out of round due to a cut near the bend (the tube will take form once connected). Slide the canister all the way until the slip-on adapter seats fully against the exhaust inlet. Wipe off any excess silicone. 7 Place each spring over the exhaust side spring tabs and use the spring tool to pull the springs over the adapter spring tabs. Both springs must be secured for proper installation. 8 Apply a small amount of silicone sealer (such as permatex Ultra Black or Ultra Copper) to the inside (inlet side) of the slip-on adapter. Slide the low profile barrel clamp over the LevelOne Adapter pipe. Slide the slip-on adapter pipe over the stock header collector. Do not fully tighten the barrel clamp

2008 – 2009 APRILIA DORSODURO 750 SLIP-ON STREEL LEGAL EXHAUST SYSTEM

0

Filed Under (Aprilia) by admin on 06-11-2010

download
Our sporty and lightweight SLIP-ON systems offer a great balance between price and performance and represent the first step in the exhaust system tuning process. The change will be also visual as our HEXAGONAL mufflers perfectly fit the exterior line of the sporty Dorsoduro and add a clean racing image. The muffler outer sleeve is made of titanium, which gives a special hi-tech touch to our SLIP-ON system. We offer street legal version with removable muffler in- serts. PERFORMANCE Measurements of the Akrapovic SLIP-ON system on the APRILIA DORSODURO 750 (without muffler insert): Power & Torque: the exhaust system modification results in a major boost in performance, delivering a solid 84.8 HP at 9540 rpm on back wheel. But the increased power isn’t available just at the top of the range; the system shows its quality already from 3500 rpm up through entire rpm range. Max. increased power between the Akrapovic and the stock system is 1.8 HP at 9300 rpm. Besides this, the torque is substantially higher in a lower rpm area from 2500 rpm to 6500, and also in middle and high rpm area. Technical specifications of Akrapovic exhaust systems and related products subject to change without notice. 20 30 40 50 60 70 80 47,5 50,0 52,5 55,0 57,5 60,0 62,5 65,0 67,5 3000 4000 5000 6000 7000 8000 9000 10000 WhlPwr EngT rq EngSpd RPM STOCK EXHAUST AKRAPOVIC SLIP-ON EXHAUST PERFORMANCE stock AKRAPOVIC max. increased power max. rear wheel power HP / rpm (measured on Dynojet ATV) 83.13 / 9560 84.8 / 9540 1.8 / 9300 ADDITIONAL DATA weight comparison (kg) stock AKRAPOVIC difference 11.13 SS link pipe TITANIUM link pipe stock – S.S. stock – TITANIUM 4.35 – 6.78 – noise measurements (dB / rpm) stock AKRAPOVIC 96 / 4375 96 / 4375

Incoming search terms:

Harley Davidson Sportster Straightshots HS Slip-on Exhaust system

0

Filed Under (Harley Davidson) by admin on 19-12-2010

download
STOCK EXHAUST SYSTEM REMOVAL 1. Loosen the heat shield clamps on both the front and rear exhaust pipes. This allows easier access to the head pipe mounting nuts. 2. Loosen, but do not remove, the two head pipe mounting nuts from each flange located at the cylinder head. 3. Remove the clamp bolt which mounts the rear head pipe to the belt drive cover bracket. 4. Loosen the clamp holding the mufflers onto the head pipes. Page 1 of 4 D480IN Rev. 1.0 Sportster Straightshots HS Slip-on Exhaust system Part #16819 U S A Congratulations, you have purchased the finest exhaust system available for your motorcycle. Your VANCE & HINES exhaust system is designed and crafted for maximum performance, a perfect fit, a great sound and unbeatable style! Please follow the installation instructions below and if you have any questions, feel free to call our technical help line (562) 926-5291. Attention Installer: (if other than owner): Please forward this instruction sheet to the purchaser of this product. These instructions contain valuable information necessary to the end user. Tools required for installation: 1/2″ combination wrench 3/8″ drive ratchet and 9″ extension 9/16″ and 1/2″ sockets 5/16″ Nutdriver/flat blade screwdriver 5. Remove the two bolts from each muffler which attach the mufflers to the mounting bar. 6. Remove the mufflers by sliding them off the head pipes. 7. Remove the clamp from the nose of each muffler (these will be re-used when installing the new mufflers). 8. Remove the gaskets from the crossover ports on the stock mufflers. Inspect the gaskets and replace if damaged or worn (H-D part #65927-00). 9. Install crossover gaskets onto mounting bar on motorcycle. VANCE & HINES EXHAUST SYSTEM INSTALLATION 1. Remove mufflers and heat shields from protective packaging. 2. Slide the nut plate inside the bracket that is welded to the backside of each muffler body and attach the muffler bodies to the mounting brackets (stamped 379-P) using four 5/16″ x 5/8″ flange head bolts (supplied). Leave them loose at this time (Figure 1). 3. Slide stock exhaust clamp onto nose of each muffler. 4. Slide mufflers onto head pipes and align crossover port with gasket on mounting bar (Figure 2). Press into place on gasket. 5. Attach the muffler brackets to the stock mounting bar using four 5/16″ x 3/4″ hex head bolts, washers, and nuts (supplied). Leave them loose at this time (Figure 3). 6. Tighten cylinder port exhaust flange nuts on front and rear cylinders. 7. Install and tighten the clamp bolt which mounts the rear head pipe to the belt drive cover bracket. 8. Align muffler and bracket so they sit level. Tighten the muffler mounting bolts and the bracket mounting bolts. 9. Tighten the clamp holding the muffler onto the head pipe.

Incoming search terms:

Yamaha YZF-R1 and R6 TiForce slip on exhaust system REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Yamaha) by admin on 09-01-2012

download
1. Remove the fairing lowers. 2. For R1 owners, please remove the existing exhaust system from the EXUP valve rearward (EXUP valve is retained) and set aside. Save the stock exhaust clamp for reuse. For R6 owners, please disconnect the stock S-bend from the rear of the collector and set aside. Save the stock exhaust clamp for reuse (new clamp provided). Save the stock end can mounting bolt for reuse as well. 3. R1 owners only -Inspect the exhaust gasket. Replace if necessary (gasket provided). 4. For R1 owners -Install the S-Bend to the rear of the EXUP valve, make sure the system fits flush. Reuse the stock exhaust clamp to connect the S-bend to the valve. For R6 owners -Install the TiForce S-bend to the rear of the stock head pipes and collector. Make sure the system fits flush and snug. Reuse the stock exhaust clamp or the provided clamp and loosely attach for now. 5. Install the TiForce end can to the S-bend tail pipe. 6. Loosely attach the two rubber bands, stainless steel bands (K), and stay to the end can using the supplied 6mm hardware (H) and the hanger / stay arm (G). See figure 1 for the assembly procedure. 7. R1 owners -Place the bands approximately 180mm from the edge of the end can. See figure 2. R6 owners -Place the bands approximately 195mm from the edge of the end can. See figure 2. 8. R1 owners -Using the stock provided mounting point on the passenger footpeg, use the M10x45mm bolt and hardware to mount the end can loosely, allowing for some adjustment. 9. Carefully align the two stainless bands so that theyare parallel to each other, and spaced properly on the can. Tighten the 6mm hardware (H). Make sure that the rubber pads fully cover the bands (K). USE CAUTION WHEN TIGHTENING THE 6MM HARDWARE AND THE TWO BANDS SO AS NOT TO CRUSH OR DISTORT THE SLEEVE OF THE CAN. 10. Using some brake and contact cleaner on a clean rag, carefully wipe down the entire TiForce exhaust system to remove any residual oils, anti seize, fingerprints and dirt prior to starting the motor. FAILURE TO CLEAN THE TUBING AND CAN MAY RESULT IN PERMANENT STAINING OF THE SYSTEM WHEN HEATED. 11. Attach the supplied springs to secure the end can to the S-bend pipe using a spring installation tool if available. Make sure the exhaust system is free and clear of the bike. If necessary, adjust for proper clearance. 12. Go back and tighten all fasteners. 13. Check that all fasteners are tightened per specifications, then start the motor and check for exhaust leaks. 14. Reinstall the fairing lowers.

Incoming search terms:

2007 Yamaha V-Star 1300 Classic Straights Installation Instructions

0

Filed Under (Yamaha) by admin on 08-11-2010

download
Stock Exhaust System Removal 1. Remove right side Foot peg assembly or Floorboard. (Whichever is applicable to your model.) 2. Remove bolts that are holding pipes at rear mounting bracket. 3. Loosen clamps at mufflers. 4. Remove mufflers. 5. Remove the two nuts that secure the rear exhaust header pipe to the rear cylinder head. 6. Remove rear exhaust pipe assembly. 7. Remove the two nuts that secure the front exhaust header pipe to the front cylinder head. 8. Remove front exhaust pipe assembly. 9. Remove exhaust-mounting bracket from frame. Hard-Krome Exhaust System Installation NOTE: Take care when fitting this Hard-Krome aftermarket exhaust system on your motorcycle. It has been designed to replace a STOCK exhaust system on a motorcycle with its engine, frame and other components in their STOCK design, configuration and location. WARNING : Re-check and re-tighten ALL fasteners and supports after 50 miles, then re-check and tighten as necessary on a periodic basis to ensure proper operation and performance. NOTE: All fasteners should be loose during initial installation to ensure proper fit and location of the new exhaust system. 1. Install new exhaust gaskets. 2. Install mounting bracket using Bolts with flat & lock washers. 3. Install Front exhaust header pipe, taking care to not scratch chrome surfaces on pipe, engine or motorcycle — use masking tape as needed. 4. Install the two nuts to secure the flange that holds the exhaust header pipe to the front cylinder head — DO NOT TIGHTEN NUTS! 5. Install Nut strip into each slotted bracket of front pipe and start the 3/8-16×3/4″ Bolt with flat & lock washer through backside of mounting bracket. — DO NOT TIGHTEN BOLTS! 6. Carefully install rear pipe. 7. Install the two nuts to secure the flange that holds the exhaust header pipe to the front cylinder head — DO NOT TIGHTEN NUTS! 8. Install Nut strip into each slotted bracket of rear pipe and start the 3/8-16×3/4″ Bolt with flat & lock washer through backside of mounting bracket. — DO NOT TIGHTEN BOLTS! 9. Tighten the two bolts that secure the rear exhaust header pipe flange. 10. Tighten the two bolts that secure the front exhaust header pipe flange. 11. Tighten front pipe bolts at mounting bracket. 12. Tighten rear pipe bolts at mounting bracket. 13. Reinstall foot peg assembly or floorboard. 14. If applicable to your model install foot peg relocating brackets and foot pegs as shown in illustration. 15. Before starting bike wipe off any fingerprints and grease off pipes. Start bike and check for any exhaust leaks. NOTE: To achieve optimum performance from your Hard-Krome exhaust system we suggest installing the Dynojet jet kit for carbureted models

Incoming search terms:

Incoming search terms: