2013 cvo if i take tour pac off can i mount back rest on bracket

You search Auto repair manual PDF 2013 cvo if i take tour pac off can i mount back rest on bracket, if there are search results will appear below. If search results do not exist, please search by others keyword.



  2013 cvo if i take tour pac off can i mount back rest on bracket Direct Download speed 5282 Kb/s

  2013 cvo if i take tour pac off can i mount back rest on bracket Full Version speed 6162 Kb/s



HARLEY DAVIDSON ROAD KING SOLO BUCKET AND PASSENGER PILLION INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 10-02-2011

download
Installation SOLO SADDLE ONLY 1. Remove stock seat and grabstrap according to applicable Service Manual instructions. 2. Road King standard models . Remove and save the stock screws and seat mount bracket at the back of the rider solo seat. 2000 and later models . Remove the retainer washer from the stud plate and replace with two black retainer washers (2). Be careful not to allow stud plate to fall through the fender. 3. Road King standard models . Install stock solo seat mount bracket using two stock screws saved in Step 2. Road King Classic Custom models . Install solo seat mount bracket onto back of solo seat using bracket and screws included in Mount Kit Number 52903-01. 4. Install seat by sliding front of seat into seat holder bracket. Pull up on the nose of the seat to verify that the seat is securely installed. After installing seat, pull upward on front of seat to be sure it is in locked position. While riding, a loose seat can shift causing loss of control, which could result in death or serious injury. (00070a) 5. 1999 and later models . Install 1/4 in. star washers (6), spacers (4) and acorn nuts (3) onto rear mount studs. Torque to 72 in-lbs (8.13 Nm). 1998 and earlier models . Install 5/16 in. star washers (5) and 5/16-18 x 3/4 in. buttonhead screws (1) into stock mount nuts. Torque to 17 ft-lbs (23 Nm). SOLOAND PILLION 1. Remove stock seat and grabstrap according to applicable Service Manual instructions. Retain all hardware for later use. 2. Road King standard models . Remove and save the stock screws and seat mount bracket at the back of the rider seat. 3. Road King standard models. Install stock seat mount bracket onto new solo seat using two screws saved in Step 2. Road King Classic Custom models. Install solo seat mount bracket onto back of solo seat using bracket and screws included in Mount Kit Number 52903-01. 4. 1999 and later Road King standard models . Secure the rear mount bracket with stock mushroom nuts (10) and two 1/4 in. star washers (6). Torque to 72 in-lbs (8.13 Nm). 1998 and earlier Road King standard models . Install solo seat by sliding front of seat into holder bracket on bike. Secure the rear mount bracket with the two mushroom screws (11) and two 5/16 in. star washers (5). Torque to 17 ft-lbs (23 Nm). Road King Classic Custom models . Mount Kit Number 52903-01 is required for installation. Install solo seat (7) by sliding front of seat into holder bracket on bike. • 1999 and later models . Using Mount Kit Number 52903-01, secure the rear mount bracket with the two mushroom nuts (10) and two 1/4 in. star washers (6). Torque to 72 in-lbs (8.13 Nm). • 1998 and earlier models . Using Mount Kit Number 52903-01, secure the rear mount bracket with the two mushroom screws (11) and two 5/16 in. star washers (5). Torque to 17 ft-lbs (23 Nm)

Incoming search terms:

HARLEY DAVIDSON HEEL REST KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 10-04-2011

download
Models Kit 50227-01 is designed for forward controls and fits: •1989 and later FX Softail Models with Original Equipment (OE) Forward Controls, •1993 through 2002 FXDWG, •Dyna models equipped with Forward Control Kit 49080- 93 or 49080-93A. Kit 50227-01 does not fit Dyna models equipped with Forward Control Kit 49080-03 or Forward Control Footrest Support 33695-03 (left) or 33697-03 (right). Kit 50236-01 is designed for mid controls and fits: •all 1990 and later Dyna Model Motorcycles with Original Equipment (OE) Mid Controls. Additional Parts Required Proper installation of this kit also requires installing a pair of Heel Rest Pegs, or Shifter Pegs, which can also be mounted as heel rests. Refer to the appropriate Parts Catalog for stock shifter pegs, sold separately. The current Harley-Davidson Genuine Motor Accessories and Parts catalog also has a selection of Heel Rest Pegs or Shifter Pegs and matching Footpegs. Any shifter peg style that is symmetrical in design can be used as a left or right side heel rest. The rider’s safety depends upon the correct installation of this kit. Use the appropriate service manual procedures. If the procedure is not within your capabilities or you do not have the correct tools, have a Harley-Davidson dealer perform the installation. Improper installation of this kit could result in death or serious injury. (00333a) NOTE A Service Manual for your model motorcycle is available from a Harley-Davidson Dealer. Kit Contents See Figure 1 and Table 1. INSTALLATION NOTE See Figure 1 for the following procedure. 1. Remove the screw (B), lock nut (C) and spring washer (E) securing the left footpeg to the footrest support bracket (A). Save the hardware for later installation. NOTE Heel rest levers are side-specific. Levers mount so the set screws are on the underside. 2. Obtain a Heel Rest Peg or Shifter Peg (D) (purchased separately) and the left side heel rest lever (3). Apply Loctite® 243 (7) to the threads of the peg and install it to the left heel rest lever. 3. Obtain the screw (B), spring washer (E) and lock nut (C) removed in step 1, and the heel rest lever and peg assembly (D). Position the lever assembly to the desired angle on the mount, and slide the lever assembly with the spring washer into the footrest support bracket as shown. NOTE Splines on the lever and mount provide for a limited range of heel rest angle adjustment. For Kit 50227-01. The heel rest lever (3) can be adjusted after the mount (1) is attached but before the set screw (2) is installed. Slide the lever inward off the spline, and rotate it to the desired angle. For Kit 50236-01. The heel rest lever (3) angle cannot be adjusted after the mount (1) is attached without removing them from the footrest support bracket (A). Check to ensure the heel rest (D) is in a comfortable position before tightening the mounting hardware. 4. Install the original screw (B) and lock nut (C) to secure the heel rest assembly to the footpeg mount. Tighten to 33 ft- lbs (45.6 Nm). 5. Obtain a screw (6), spring washer (5) and nut (4) from the kit. Install the footpeg to the heel rest assembly and tighten to 33 ft-lbs (45.6 Nm). 6. Obtain a set screw (2) from the kit. Apply Loctite® 243 (7) to the threads, and install the set screw to the heel rest lever. Tighten to 16 in-lbs (1.8 Nm). 7. Perform Steps 1 through 6 for the right side. USE

Incoming search terms:

HARLEY DAVIDSON TOURING DETACHABLE TOUR-PAK RACK INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 09-02-2011

download
INSTALLATION NOTE See Figure 3. When installing Tour-Pak to Rack in the following Steps, note that holes on Rack provide two positions for mounting Tour-Pak in desired location. 1. Place Tour-Pak on support tube and open lid. NOTE See Figure 3. In the following step, the longer bolts (6) are used for 2005 and earlier (King only) and Chopped Tour-Paks while the shorter bolts (5) are used for Leather Tour-Pak and 2006 and later King Tour-Paks. 2. See Figure 3. Obtain bolt (5 or 6), two flat washers (3), concave spacer (4) and hex lock nut (2) from kit. Align rear center hole in Tour-Pak with same hole in support tube (8). Slide bolt with flat washer through Tour-Pak, through support tube, then through concave spacer (with concave side facing support tube). At bottom of support tube, install washer (3) and nylock cap nut (2). With concavity on spacer inline with the rail, hold nut and tighten bolt until snug. 3. Obtain bolts (5 or 6), two flat washers (3), concave spacer (4) and hex lock nut (2) from kit. Align top support tube (8) with detachable tour-pak rack holes (four). Slide bolts with flat washer through Tour-Pak, through support tube, through concave spacer (with concave side facing support tube) then through rack. At bottom of detachable tour-pak rack, install washer (3) and nylock cap nut (2). With concavity on spacer inline with the rail, hold nut and tighten bolt until snug. NOTE Always install the mounting bolts from inside the Tour-Pak. If the bolts are installed upside down, then the ends of the bolts can tear the molded liner and scratch objects, such as helmets, stored inside the Tour-Pak. 4. Repeat Step 3 and install hardware to the remaining three holes in Tour-Pak and mounting rack. 5. In a crosswise pattern, alternately tighten the five bolts to 96-120 in-lbs (10.8-13.5 Nm) . Be sure that concavity on each spacer is inline with the rail and has not rotated out of position. INSTALLATION-TOUR-PAK AND RACK 1. Follow the instructions included in the docking point kit and install docking points. 2. See Figure 1. While standing behind the motorcycle, place the front Tour-Pak rack notches into the front docking points (1). Make sure the notches seat fully into the front docking points. 2 1 is04025 1. Front Docking Point 2. Rear Docking Point Figure 1. Docking Point Bracket 3. See Figure 1 and Figure 2. Position the latches over the rear docking points (2). Check to be sure the latches fit into the neck of the rear docking points as shown in figure 2. This may require some gentle squeezing or spreading of the rack

Incoming search terms:

HARLEY DAVIDSON CONTOURED TOUR-PAK LUGGAGE RACK KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 05-04-2011

download
INSTALLATION NOTE The location of the Tour-Pak spoiler has a direct relationship to the location of Tour-Pak mounted luggage rack. The spoiler template will locate the Tour-Pak spoiler in the correct position for the luggage rack so that the spoiler may be added in the future. It is recommended that the spoiler be installed first. See Figure 1. 1. Identify if the installation of a Tour-Pak mounted spoiler is desired in the future. Use the template if the spoiler will be installed. Cut the template along the appropriate line. Carefully place template on top of Tour-Pak lid, aligning edges of template with top surface of Tour-Pak. Tape template in desired location. 1 is 00579 1. Check clearance between rack and spoiler Figure 1. Tour-Pak Rack and Spoiler NOTE Position top rack with upright section toward rear of motorcycle. To avoid contact with the passenger backrest pad, do not mount the top rack in too far forward a position. 2. See Figure 2. Place the four mounting pads (1) onto the four mounting supports on top rack (2). Carefully center the rack on the lid and position the rack rear supports 5/8 inch to 3/4 inch (16 mm to 19 mm) in front of the emblem on the Tour-Pak lid, as shown. 1 is 00636 1.5/8 in. – 3/4 in. (16 mm – 19 mm) Figure 2. Locate Holes From Emblem 3. Use a grease pencil to temporarily mark the positions of the four mounting pads on Tour-Pak cover. NOTE Apply masking tape to the Tour-Pak cover painted surface at the four points where the top rack mounting holes will be drilled. The tape can be marked for hole location, and will help prevent the paint from being chipped during the drilling procedure. 4. Carefully remove top rack/mounting pad assembly. Place a strip of masking tape over each grease pencil mark on the Tour-Pak cover. Once again, position top rack/mounting pad assembly on Tour-Pak cover in the desired mounting location. 5. Using a soft lead pencil on the masking tape strips, trace a circle around each mounting pad. Remove top rack/mounting pad assembly. Use a ruler to mark the exact center of each circle drawn on the tape strips. NOTE Remove all contents from within the Tour-Pak to avoid possible contact with the moving drill bit during the following drilling procedure. 6. Drill starter holes using a 1/16 inch drill bit. Drill the finished holes for the mounting screws using a 9/32 inch drill bit. Remove masking tape strips. 7. Apply a small amount of silicone sealant around each mounting hole on interior surface of Tour-Pak cover

Incoming search terms:

1100cc Honda Goldwing Installation Manual

0

Filed Under (Honda) by admin on 29-04-2011

download
Receiver Hitch Installation Install all bolts loosely until all brackets are in place 1) Place motorcycle on center stand and be certain it is level. 2) Remove saddlebags if necessary for easier installation. 3) Mount bracket A to the lower front crash bar bolt Left side (new bolts provided) and top of left hitch arm. 4) Mount bracket B to the lower front crash bar bolt Right side (new bolts provided) and top of right hitch arm. 5) Bracket C mounts to rear of hitch and sub frame bolt located behind tail light (new bolt provided) This bracket mounts inside the rear fender. 6) Attach brackets D and E to rear of hitch. 7) Bracket F attaches to bottom of bracket D and trunk sub frame with U-bolts. Insert bottom U-bolts at step 9 8) Bracket G attaches to bottom of bracket E and trunk sub frame with U-bolts. Insert bottom U-bolts at step 9 9) Brackets D and E (with brackets F and G) attach to bottom rear saddlebag sub frame with U-bolts. 10) Tighten all bolts. INSTALLATION OF THE TOW-PAC HITCH CART. 1. Place your motorcycle on a smooth flat surface, like a garage floor, and rest it on its center stand. 2. Assemble the axles, tires and wheels, and fenders onto the tow- pac hitch cart. 3. Carefully align the tow-pac hitch cart’s hitch mount with the receiver hitch on the motorcycle. Now push the hitch mount into the receiver hitch. (this might be a little difficult until you get use to doing it. Removing the paint from the hitch mount and applying a little grease will help.) 4. Place the hitch pin through the receiver hitch and hitch mount ( alignment plate ). Install and tighten the tension bolt. 5. Push the motorcycle off of the center stand and risers if used. 6. Bolt leanstop braces to hitch. (Bolt inserts from the bottom) Be certain to replace washers/spacers in the same configuration as when you removed them. see diagram next page 7. Check all bolts for tightness. 8. You are now ready for the test ride. A. Keep your feet up! B. Ride slowly in first gear until you are comfortable with the Tow-Pac system.

Incoming search terms:

Yamaha Virago 750/ 1100 InstaTrike REMOVAL AND INSTALLATION MANUALS

0

Filed Under (Yamaha) by admin on 26-12-2011

download
Remove any aftermarket accessories (saddle bags, back rests, etc) before hitch installation. After installation remount accessories. NOTE: Some aftermarket accessories may not be compatible with InstaTrike hitch. 1) Place motorcycle on a smooth level surface on center stand. 2) Attach Bracket A (left) to outside of rear passenger foot peg mount. Place spacers between Bracket A and foot peg mount. Use new bolts provided. 3) Attach Bracket B (right) to outside of rear passenger foot peg. Place spacers between Bracket B and foot peg mount. Use new bolts provided. Bracket will extend over top of mufflers. 4) Attach Brackets C (left) and D (right) to rear frame bolts on
motorcycle. Located near rear turn signals Use new bolts provided. (10M x 25mm long) It may be necessary to loosen or remove backrest covers or hardware in order to easily access rear frame bolts. After Bracket C and D installation, reattach and/or tighten backrest mounts. 5) Attach Bracket E(left) / F(right) to bottom of Brackets A & B and to the TOP of the forward hitch arms. Ensure hitch is square on motorcycle and snug bolts for Brackets A, B, and E,F at this time. 6) Raise rear of hitch so bottom of Brackets C & D are flush with top of rear hitch plate. Ensuring that hitch is square with motorcycle, carefully mark hole locations for bottom of Brackets C&D on rear hitch plate. Drill rear hitch plate holes with 3/8 inch drill. This step ensures proper alignment and spacing of hitch on the motorcycle. 7) Tighten all bolts ensuring that hitch is square on motorcycle. Periodically check bolts for tightness. Bracket Identification
INSTALLATION OF THE TOW-PAC HITCH CART.
1. Place your motorcycle on a smooth flat surface, like a garage floor, and rest it on its center stand. 2. Assemble the axles, tires and wheels, and fenders onto the tow- pac hitch cart. 3. Carefully align the tow-pac hitch cart’s hitch mount with the receiver hitch on the motorcycle. Now push the hitch mount into the receiver hitch. (this might be a little difficult until you get use to doing it. Removing the paint from the hitch mount and applying a little grease will help.) 4. Place the hitch pin through the receiver hitch and hitch mount ( alignment plate ). Install and tighten the tension bo

Incoming search terms:

1300 Yamaha V-Star Installation Manual

0

Filed Under (Yamaha) by admin on 07-11-2010

download
1) Place motorcycle on a firm level surface and secure in a upright position. 2) Remove saddle bags and saddle bag hardware (Tourer model only) Also remove rear riders pegs (Tourer model requires removal of rear footpeg offset hardware as well) 3) Attach bracket A (right) / B (left) to rear footpeg attachment point using new bolts provided. Remount footpegs/saddlebag hardware over top of brackets A/B. NOTE: Do not attach leveling stand bracket at this time 4) Attach bracket C(right) / D(left) to rear fender sub frame using new bolts provided. (Tourer model only – Saddle bag hardware mounts to the outside of brackets C/D. Brackets C/D mount between chrome side rail and saddlebag hardware.) NOTE: Brackets C/D have welded spacers which attach in toward rear fender 5) Attach top of Bracket E(right) / F(left) to rear of brackets C/D. Brackets E/F mount to the inside of brackets C/D. NOTE: Use ½ inch spacer between brackets E/F and C/D on Tourer model ONLY
6) Attach rear of brackets A/B to TOP of forward hitch arms. Attach bottom to brackets E/F to rear hitch plate. 7) Carefully tighten all bolts at this time ensuring hitch is square with motorcycle. Hitch Bracket Identification Leveling stand screw jack installation 1) Attach leveling stand brackets to brackets A and B 2) Thread right side screw jack into threaded hole on leveling stand bracket attached to bracket A sand adjust leveling jack bolt out. 3) Push motorcycle over from left side until right screw jack is touching floor. 4) Thread left side screw jack into threaded hole on leveling stand bracket attached to bracket B and adjust out until motorcycle will rest upright on both screw jacks. 5) Adjust screw jacks until motorcycle is level. 6) After InstaTrike is attached to or removed from receiver hitch, be sure to remove leveling stands and leveling stand brackets. CAUTION – Use screw jacks to hold motorcycle upright and level ONLY. Do not lift motorcycle with screw jacks. CAUTION – Use care when installing screw jacks. Be certain that motorcycle is always in a stable balanced position.
INSTALLATION OF THE TOW-PAC HITCH CART. 1. Place your motorcycle on a smooth flat surface, like a garage floor, and install leveling stands. Install right leveling stand first. Carefully raise motorcycle off of side stand and install left leveling stand. Caution – Use leveling stands to level motorcycle ONLY. Do not raise motorcycle with stands Caution – Be certain that motorcycle is always in a stable balanced position when installing leveling stands. 2. Assemble the axles, tires and wheels, and fenders onto the tow- pac hitch cart. 3. Carefully align the tow-pac hitch cart’s hitch mount with the receiver hitch on the motorcycle. Now push the hitch mount into the receiver hitch. (this might be a little difficult until you get use to doing it. Removing the paint from the hitch mount and applying a little grease will help.) 4. Place the hitch pin through the receiver hitch and hitch mount ( alignment plate ). Install and tighten the tension bolt

Incoming search terms:

HARLEY DAVIDSON TOUR-PAK RACK LIGHT KIT INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 06-02-2011

download
INSTALLATION 1. Remove all contents from Tour-Pak®. 2. For easier installation, remove Tour-Pak rack, if installed, by removing cap screw, washers and mounting pads. 3. See Figure 1. Remove rubber plug from bottom rear rail on left side of rack. 4. See Figure 2. Use line wire feeder in kit to thread through left rear rack foot and out through the back opening of rail. 5. Attach light harness wires to line wire feeder loop. 6. Carefully pull line wire feeder and light harness wires through rack mounting foot. 7. See Figure 5 and Table 1. Apply foam pads (5) to top surface of light. 8. Secure light (1) to rack with socket head screws (4) and washers (6). 1 is05242 1. Plug Figure 1. Left Side Rack Plug 1 is05244 1. Line wire feeder Figure 2. Thread Wires Through Rack 9. Position rack/light assembly to Tour-Pak lid and route wires through lid, washer and hollow mounting bolt. 10. Attach rack/light assembly to Tour-Pak using instructions and hardware provided with rack except for use of hollow bolt from Step 9. 11. Remove Tour-Pak liner. 12. Thread wires through black vinyl conduit. 13. Ultra Classic models: Follow Steps 14 through 2114. Locate and disconnect three pin AMP connector for Tour- Pak lights. 15. See Figure 3. Attach the Y-harness (2) to the three pin male connector (1) of Tour-Pak harness. 16. Route light wires from back of Tour-Pak along left side to front. Secure conduit with adhesive clips provided in kit. 17. Trim length of light wires and conduit to reach Y-harness. 18. Refer to the Service Manual electrical appendix to install terminal pins (8) to rack light wires and install terminals to three pin housing (7) as follows: a. #1 cavity = blue lead b. #2 cavity = red with yellow lead c. #3 cavity = black lead 19. Connect rack light to remaining Y-harness connector. 20. Replace Tour-Pak liner. 21. Check operation of Tour-Pak tail and stop light functions before operating motorcycle. 22. Classic models: See Figure 4. If necessary, drill hole in lower left bottom of Tour-Pak and install grommet. Route rack light wires through grommet. 23. Refer to the Service Manual electrical appendix to install terminal receptacle (8) to rack light wires and install terminals to three pin receptacle housing (7) as follows: a. #1 cavity = blue lead b. #2 cavity = red with yellow lead c. #3 cavity = black lead NOTE To prevent corrosion, fill the cavities of the connectors with dielectric grease (included in kit) prior to making connections. As an additional precaution against moisture seepage into the Tour-Pak, apply silicone sealant (not included in kit) to the entrance of the light harness wire tunnel. See figure 2 for location reference. 24. Connect rack light to male connector of two connector wire harness (12) and connect to accessory connector under seat. 25. Replace Tour-Pak liner. 26. Check operation of Tour-Pak tail and stop light functions before operating motorcycle

Incoming search terms:

HARLEY DAVIDSON TOUR-PAK KIT INTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 07-02-2011

download
INSTALLATION 1. Remove the rubber mat from the bottom of the Tour-Pak. 2. See Figure 1 and Table 1 to determine the proper hole configuration to attach the Tour-Pak to your luggage rack. Holes will be drilled as explained in Step 3 in the hole location for your luggage rack. Table 1. Luggage Rack and Hole Configurations Hole Configura- tion Luggage Rack C (3 holes) Stock 1997 B (4 holes) Detachable luggage rack 53107-96 A (5 holes) Luggage rack 53118-97A and luggage rack 53118-98 A (5 holes) Stock 1998 and later racks A (5 holes) Detachable Tour-Pak rack 53276-04 B (4 holes) Solo detachable Tour-Pak rack 53655-04 B (4 holes) Detachable Tour-Pak rack 53066-00B B (4 holes) Solo detachable Tour-Pak rack 53559-04A A (5 holes) Solo detachable Tour-Pak rack 53260-02 -J03631 1 of 3 B 1 A C 2 2 2 is00163 1. Front of motorcycle 2. Bottom view of Tour-Pak interior (rubber mat removed) Figure 1. Hole configurations for Tour-Pak attachment NOTE Drilling holes in Tour-Pak without wood underneath each hole site may result in the leather becoming damaged during the drilling process. 3. Place blocks of wood underneath the Tour-Pak where the holes will be drilled to prevent damage to the leather while drilling. Use the pre-drilled holes in the metal base as a guide and carefully drill the holes through the leather in the proper location using a 11/32 inch drill bit. 4. See Figure 2. For detachable luggage racks (53107- 96, 53066-00B and 53276-04): Install black cover tube to the front bar (1) of the luggage rack, as shown. This tube is used to provide a cleaner look. The black cover tube is not for use with other luggage racks. 5. Attach Tour-Pak to rack using the mounting screws provided in the Luggage Rack kit. Put bolt through from inside of Tour-Pak. Tighten screws to specifications found in the Luggage Rack kit. 6. Place the black rubber mat on the bottom of the Tour-Pak. 7. If luggage rack was removed, reattach to motorcycle according to kit instructions or Service Manual instructions

Incoming search terms:

HARLEY DAVIDSON XR1200 LUGGAGE RACK KIT REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 29-03-2011

download
Kit 53976-08 (XR1200 Passenger Upright Kit) is available for separate purchase. Contact your Harley-Davidson dealer for more information. Kit Contents See Figure 2 and Table 1. REMOVAL 1. Remove pillion and seat following the instructions in the appropriate Service Manual. 2. Remove the seat base following the instructions in the appropriate Service Manual. 3. See Figure 1. Remove the turn signal mounting screws (3) and discard. Allow the turn signal to hang by the harness until lower bracket installation. 4. Remove the rear fender support strut screws (6) and dis- card. INSTALLATION 1. See Figure 2. Install lower luggage rack mount bracket with screws (9), flat washers (10) and nuts (8). Bracket will mount around nut (Item 2 in Figure 1). Tighten to 19 ft-lbs (26 Nm) . 2. Install screws (7) and nuts (8) through the rear fender support strut and the lower luggage rack mount bracket. Tighten to 19 ft-lbs (26 Nm) . 3. Route the turn signal wire harnesses through the groove in the bracket. Install new turn signal mounting screws (11). Tighten screws to 3-5 ft-lbs (4-7 Nm) . 4. Install seat base following the instructions in the appropriate Service Manual. 5. Install upper luggage rack mount bracket (4) with original equipment seat base screws in the lower holes (A). Do not tighten at this time. 6. Install screws (3) into slotted holes in the upper luggage rack mount bracket (4) and flange nuts (6). Slide the upper bracket as far back in the slots as possible. Tighten screws (3) to 10 ft-lbs (13.5 Nm) 4 1 1 2 5 6 3 is05250 1. Lower luggage rack mount bracket screw (4) 2. Nut (2) 3. Turn signal mounting screw (4) 4. Upper luggage rack mount bracket 5. Luggage rack 6. Rear fender support strut screw (2) Figure 1. Luggage Rack Installation NOTE If installing the Passenger Upright Kit (part number 53976-08) (available separately), do not install spacers (2) and screws (3) in front holes. 7. Install luggage rack (1) aligning the holes with the holes in the upper luggage rack mount bracket. Install spacers (2) and screws (3) in holes. Tighten to 6-10 ft-lbs (8-13.5 Nm) . After installing seat, pull upward on seat to be sure it is locked in position. While riding, a loose seat can shift causing loss of control, which could result in death or serious injury. (00070b) 8. Install pillion and seat following the instructions in the appropriate Service Manual. Do not exceed luggage rack weight capacity. Too much weight can cause loss of control, which could result in death or serious injury. (00373a

Incoming search terms:

Incoming search terms: