2013 kawasaki voyager 1700 problems

You search Auto repair manual PDF 2013 kawasaki voyager 1700 problems, if there are search results will appear below. If search results do not exist, please search by others keyword.



  2013 kawasaki voyager 1700 problems Direct Download speed 5282 Kb/s

  2013 kawasaki voyager 1700 problems Full Version speed 6162 Kb/s



Kawasaki Voyager 1700 Hitch Removal both saddlebags and Installation Instructions

0

Filed Under (Kawasaki) by admin on 08-05-2012

download
Remove the seat. Remove both saddlebags by removing the 3 bolts shown below Remove the plastic liner in the bottom of the trunk by gently pushing in on the center of the plastic clips Once the liner is removed remove the trunk rear light assembly by removing the 4 black screws in side the trunk and 4 on the bottom side of the light assembly. Unplug the light assembly and set it aside. Remove the bolts for the trunk Have a friend hold the trunk up and remove the 4 screws (two on each side) for the side trim Put the bolts back inside the trunk and tighten finger tight to make sure it does not fall. Remove the remaining side trim screws, 5 on each side, and remove the side trim and set it aside Remove 2 bolts from the saddle bag supports. Place the side plate mounting bracket behind the saddlebag supports and replace the two bolts you removed in the previous step. (We recommend using a few drops of Loctite). Do this step for both sides of the bike. Place the side plate behind the mounting bracket and attach the side plates to the mounting brackets with the two bolts supplied with the hitch (We recommend using Loctite on this step) Repeat this step for both sides of the bike

Incoming search terms:

Kawasaki Ninja 650R (ER-6F) & ER-6N Resource Upgrading the Suspension on the Kawasaki ER6-F/ N

0

Filed Under (Kawasaki) by admin on 30-11-2010

download
Top fork is as removed. Kawasaki Ninja 650R (ER-6F) & ER-6N Resource Before removing the fork from the clamps on the yokes I loosened the fork top. Before removing the fork top the fork-slider was placed in a vice and the bottom bolt loosened….. … before finally being removed with the fork upside down. Because the springs were still in situ this gave sufficient tension on the damper-rod to prevent it from turning and allow the bolt to be removed. When I turned the fork the right-way up to remove the fork-top I did it over a container to catch the oil. Kawasaki Ninja 650R (ER-6F) & ER-6N Resource All the OE components that will no longer be required. Left to right. Fork-top, spacer tube, washer, spring, damper-rod. Bottom bolts get re-used. Old and new, laid-out for comparison. The damper unit, minus spring and fork-top, drops inside the stanchion and slider. Kawasaki Ninja 650R (ER-6F) & ER-6N Resource Then the bolt goes back in, as tight as possible, to secure it. Top fork is done, second one awaits. Note the spring seat on the right, just below the spring. This drops over the damping rod after the oil has been added. The small locking-nut screws over the threaded part of the damping-rod next, all the way to the bottom. Spring drops in and then the fork-top screws on to the damping-rod as well, all the way down to the lock-nut which is used to secure it. At this point the stanchion is extended to the fork-top which is screwed in. Job done.

Incoming search terms:

Kawasaki Exhausts – ZX-6 ZX-10 Zx-14 Exhaust – Slip-ons INSTALLATION MANUAL

0

Filed Under (Kawasaki) by admin on 25-10-2010

download
Our favorite exhaust options for Kawasaki ZX Ninjas – ZX-10,ZX-6r, and the new horsepower king, Zx-14.. Grab your horsepower today. We love Rob Muzzy and Muzzy Exhausts.Going back to Doug Chandler and Scott Russell, Muzzy has been synonomous with Kawasaki and performance – and for years, if you rode Kawasaki,and you were on the podium, Muzzy was on your exhaust. We also feature Arrow and Yoshimura exhausts for your ZX-6R, ZX-10 and ZX-14. We love the sound of a Yosh exhaust on any Kawasaki Ninja. Yoshimura Oval (RS-3) Race Slip-On for Kawasaki ZX14R 2006 The easiest and least expensive way to experience Yoshimura performance is with our Slip-On/Bolt-On lines. Bolt-On style bolts to the O. E. M. mid-pipe Slip-On style with its stainless steel easily attaches to the mid-pipe RS-1 is available where noted Usually, no jetting or re-programming is required and installation is a snap Hindle Stainless Exhaust High Head Pipes – Kawasaki ZX6R-RR 03-04 The worlds lightest stainless steel exhaust system. Increase horsepower and torque throughout the entire rpm range. Lightweight, strong stainless steel header design looks great and weighs less than stock headers. Available in low- and high-mo North Denver News http://northdenvernews.com Powered by Joomla! Generated: 19 October, 2010, 12:28 Hindle Stainless Exhaust Low Head Pipes – Kawasaki ZX9R 00-03 The worlds lightest stainless steel exhaust system. Increase horsepower and torque throughout the entire rpm range. Lightweight, strong stainless steel header design looks great and weighs less than stock headers. Available in low- and high-mo

Incoming search terms:

2009 Kawasaki Voyager Heated Grips Installation Manual

0

Filed Under (Kawasaki) by admin on 25-10-2010

download
Remove the Factory Grips Before removing the factory grips, the”chromed plastic”grip end caps need to be removed. The chromed plastic ends are threaded on, but have”left hand”threads, which means to unscrew you need to turn them clockwise. (The opposite way that you would normally unscrew something) To do that I recommend using, either a rubber strap wrench, ora sheet of thin rubber used as you would to loosen the lid of ajar. Once Ihadtheend caps off, I used a sharp utility knife to cut through, and peel off the factory rubber grips. (They are only about 1/8″thicksoit’seasytodo.) With the rubber grips off, I removed the chromed ring that is adjacent to the left switch housing. The left ring will come off, witha gentle pull, but the throttle side ring will need to be cutoff, as it’s pressed on. It’seasytodo; I cut it off using wire side cutters (see picture on page 3 below). 2 Factory left and right Grips After removing the chromed end cap, and the factory rubber grips. The chromed plastic ring next to the switch housing needs to be cut off. Note all the ridges on the sleeve, all these except one ridge need to be filed off. 1. Prepare left handlebar for grip installation The left handlebar is pretty easy to prepare, first I cleaned any glue from the bar, and then gently test fit the left grip, be very careful here as it needs to slide on easily. Asper the instructions, ” Do not force the grip on with anything greater than gentle hand force “. Remember after the test fit you need to take it off again. (You could also crack the heated grip if it’stootight). If you find it too tight, as I did sand the bar using sandpaper until it slides on and off easily. On my bike I used an 80 grit sandpaper, and it took approx 20 minutes to geta good fit

Incoming search terms:

KAWASAKI VOYAGER AIR HORN INSTALLATION INSTRUCTIONS

0

Filed Under (Kawasaki) by admin on 27-12-2010

download
1. Remove the false fuel tank cover to expose the battery. Remove the right hand lower leg fairing. (4 phillips screws). Unplug the stock horn and remove the (2) 10mm bolts securing it to the frame. 2. See photo #1 using the stock horn bolts attach the black horn mounting bracket and the white ground wire supplied as shown. Next locate the relay supplied. Plug the stock horn wires into the relay terminals #85 & #86. (see wiring diagram on back side of instructions) 3. Attach the air hose to the compressor air outlet fitting. Attach the short red wire supplied to the compressors positive (+) terminal and the white wire installed earlier to the compressors ground (-) terminal. As shown in photo #2. Attach the compressor to the frame with the hose clamp provided. Note: position the top of the compressor as shown touching the bottom of the horn mounting bracket and approximately 1 Ω” to the rear of radiator and shroud. Also the air hose and fitting should be in front of the frame tube with the hose routed inside the hose clamp without pinching the hose. Attach the red wire from the compressor to one of the relays remaining outer terminals #30 or #87. Attach the remaining long red wire (supplied) to the remaining relay terminal #30 or #87. Secure the relay to the frame with a cable tie supplied. Route the red wire up to the battery positive (+) terminal. Locate the fuse wire assembly provided. Attach the fork end of the fuse wire to the battery positive (+) terminal. Cut the red wire to the desired length, strip the end and crimp to the fuse assembly. Turn on the ignition and press the horn button, you should hear the compressor motor run. Re-install the false fuel tank lid. Re-install the right lower leg fairing while routing the air hose out next to the black horn mounting bracket 4. See photo #3, Bolt the horn set to the black mounting bracket using the 5/16 x æ”bolt, washer and lock washer provided. Trim the air hose to length if necessary and attach the air hose to the horn assembly. Install the trumpet covers. (see instructions enclosed with covers) Turn on the ignition and test the horns

Incoming search terms:

Kawasaki Voyager Installation And Removal Manual

0

Filed Under (Kawasaki) by admin on 25-10-2010

download
Review entire installation manual Remove saddle bags and rear fender cover Modify rear fender bolt slots Install receiver hitch and double check all bolts Remount saddle bags Assemble InstaTrike hitch cart Attach InstaTrike to motorcycle via receiver hitch Attach leanstop brace bolts to receiver hitch Align InstaTrike wheels Double check all bolts for tightness Test ride InstaTrike slowly in an open area to familiarize yourself with handling characteristics Receiver Hitch Installation INSTALL ALL BOLTS AND BRACKETS LOOSLEY UNTIL ALL COMPONENTS ARE IN PLACE! 1) Place motorcycle on its center stand 2) Remove saddle bags and rear fender 3) At the bottom of the rear fender locate two bolt slots. (bolts were removed from these when rear fender was removed) Open the front end of these slots in order to remount fender. 4) Replace bottom fender bolts about 2 or 3 turns. This is necessary to be able to remount rear fender. 5) Attach bracket A to motorcycle. Locate two threaded holes (6mm) near the top of the sub frame. Bolt top of bracket A to these holes. ( bolts provided ) 6) Attach bracket B ( left side ) / C ( right side ) to motorcycle by replacing the bolt that holds the muffler to the frame and vibration absorber with the new bolt provided. Bracket B/C mounts on the outside of the large chrome washer. 7) Attach brackets A, B, C to the hitch ( top ) 8) Replace rear fender 9) Attach brackets D and E to the motorcycle sub frame with U- bolts provided. Attach brackets to hitch. 10) Tighten all bolts and double check. 11) Reinstall saddle bags

KAWASAKI STX-12F, STX-15F Riva/Vortech Supercharged STX-15F Engine INSTALLATION MANUAL

0

Filed Under (Kawasaki) by admin on 25-10-2010

download
Our race bred Supercharger System for the Kawasaki STX-15F contains all necessary engine components to produce the ultimate 80mph closed course race craft. Kit contains the same specifications that Team Kawasaki won two 2004 Pro Runabout World Titles with. System produces over 300hp using VP MS109 race fuel (Jet X). Kit includes Vortech Supercharger & Intercooler Forged Racing Pistons, Free flow Exhaust Kit, Race programmed ECU, High volume Injectors & Fuel Pump along with all necessary hardware and detailed installation instructions. Riva/Vortech Supercharged STX-15F Engine (Team Kawi Spec) PERFORMANCE DATA Stock 61 MPH @ 7,600 RPM Supercharged 80+ MPH @ 8,300 RPM RIVA STX-15F OFFSHORE RACE KIT Our Offshore Racing Kit for the Kawasaki STX-15F contains the same components and specifications that Team Kawasaki developed to dominate the international racing circuit. This modification delivers over 200hp producing awesome acceleration and a top speed of over 700mph using VP MS109 race fuel (Jet X). Kit includes high compression racing pistons, performance intake & exhaust cam shafts, Race programmed ECU along with all necessary gaskets and detailed installation instructions

Incoming search terms:

The New Kawasaki ZX-6R Trading in gets easier and easier

0

Filed Under (Kawasaki) by admin on 18-02-2011

download
didn’t go to my local Kawasaki shop expecting to trade in the 2004 636 I’d been happily riding. I honestly didn’t expect there to be anything on the floor that would motivate me to bring the bike in. Some of you reading this may be able to relate to what I am saying, the day you don’t look for something is the day that you find exactly what you didn’t know you need. That was the day I decided I needed to take home the new ZX-6R. The reworking of the new ZX-6R is more than just about looking good. According to KMC the engine has been redesigned from the crankcase up for the first time in ten years. Racing technology built into the new bike is a close-ratio cassette transmission that can be removed without the needing to split the main crankcases in case you needed to make repairs or adjustments at the track. They also tell us that the fuel injection system has shorter throttle bodies with a smaller diameter bore which claim to give this new smaller sized engine more torque in the mid-range. It also comes with a GPS – Gear Position Sensor. The new ZX-6R comes stock with a slipper clutch which is one difference between the 2004 and 2007. My 2004′s rear wheel would hop if I geared down before a corner and my engine rpms were too high. The slipper clutch allows quicker downshifts. To experience the gains of a slipper clutch you don’t have to buy a 2007 Kawasaki – it was introduced to the 636 in 2005. A quick glance at the exhaust might leave the impression that the ZX-6R comes stock with stacked twin small diameter exhaust cans but if you look closely you will see it is a single oval pipe with a shotgun styled end cap. The titanium pipe has the pre-chamber and catalyser located below the engine to keep the weight on the bike low and centered and the temperature of the under seat silencer reduced. Looking at the new Kawasaki with its fairing removed, I wonder how much more it would have cost the consumer to have an exhaust system that not only works wonders but would be worth showing off? Even if some of the systems of the new 600 look better hidden by plastic the bike does have a cohesive look and every year the fit and finish of Kawasaki’s bikes seem to get better. You can look at this bike from almost any angle and nothing jumps out at you – unless you are on the right side of the bike looking at the rear brake reservoir. It seems odd to me that they would leave the rear brake reservoir exposed. Another design feature of the smooth body of the 2007 ZX-6R is the lack of tie down points for any luggage. It can be argued that this is a bike intended for Sunday morning canyon rides or track days on weekends but if you want to take the 600 out for a weekend away then there is aftermarket solution. Ventura Racks allow you go on vacation with your bike. A Ventura Rack provides you with a frame that you attach to your bike that you can secure luggage to. There is no drilling of body work and the Ventura rack I got fit onto the bike perfectly the first try. One of the things I really like about the Ventura Rack is that you can easily attach bags that you may already have or you have the option of buying the Ventura luggage system. Just give yourself time before a motorcycle trip to pack

Incoming search terms:

KAWASAKI 1700cc Liquid-Cooled V-Twin Engine 6-Speed Transmission with Overdrive

0

Filed Under (Kawasaki) by admin on 13-12-2010

download
Kawasaki’s first production bagger model is ready to take the street by force. The new Vulcan® 1700 Vaquero™ motorcycle combines the authority of a massive 1700cc liquid-cooled V-Twin engine together with low-slung, streetwise styling of a frame-mounted front cowling and lower chin fairing, sleek side-opening hard bags, and a choice of stealthy Ebony or fiery Candy Fire Red monotone paint. Besides its unmistakable style, the Vaquero also includes a smooth-shifting 6-speed overdrive transmission, cruise control, a full-feature audio system, and a host of custom-designed accessories. Get ready to rumble. 1700cc Liquid-Cooled V-Twin Engine The Vulcan 1700 Vaquero’s 1700cc V- Twin bristles with low-rpm torque, ensuring immediate and potent acceleration. 6-Speed Transmission with Overdrive With its overdrive top gear, the Vaquero’s 6-speed transmission teams up with the V-Twin engine for a relaxed highway cruising experience. Frame Mounted Front Cowling Muscular front cowling features a cut-down windscreen for a minimalist look and uninterrupted airflow, and is frame-mounted for light handling. Side-Opening Hard Bags Holding an impressive 9.2 gallons of storage apiece, the side bags integrate neatly into the Vaquero™’s smooth, clean lines. Electronic Cruise Control Conveniently located on the right handlebar, the Vaquero’s standard electronic cruise control precisely maintains speeds between 30 and 85 mph. Full-Feature Audio System High-fidelity audio system features AM/FM and weather radio, and is can be accessorized with iPod players, XM Radio and CB radios. Multi-Function LCD Instrumentation Located on the Vaquero’s stylish “muscle car” inspired dashboard, the multi-function LCD instrumentation clearly organizes and presents all essential information.
Engine Four-stroke, liquid-cooled, SOHC, four valve per cylinder, 52° V-twin Displacement 1,700cc / 103.7ci Bore X Stroke 102 x 104mm Compression Ratio 9.5:1 Maximum Torque 108 lb-ft @ 2,750 rpm Cooling System Liquid, plus cooling fins Ignition TCBI with Digital Advance Induction Digital fuel injection, dual 42mm throttle bodies Transmission 6-speed with overdrive and positive neutral finder Frame Type Steel, double-cradle with box-section single-tube backbone Rake/Trail 30° / 7.0 in. Front Suspension / Wheel Travel 45mm hydraulic fork / 5.5 in. Rear Suspension / Wheel Travel Swingarm with twin air-assisted shocks, with 4-way rebound damping / 3.1 in. Front Tire Size 130/90×16 Rear Tire Size 170/70×16 Brakes, Front / Rear Dual 300mm discs, dual twin-piston calipers / Single 300mm disc, twin-piston caliper Overall Length 98.8 in. Overall Width 38.2 in. Overall Height 50.8 in. Seat Height 28.7 in. Curb Weight 835.7 lbs.** Wheelbase 65.6 in. Fuel Capacity 5.3 gal. Color Choices Ebony, Candy Fire Red Warranty 36 months Good Times™ Protection Plan 12, 24 or 36 months ** Curb weight includes all necessary materials and fluids to operate correctly, full tank of fuel (more than 90-percent capacity) and tool kit (if supplied

Incoming search terms:

Kawasaki KZ750 Twin Carburetor Installation Manual

0

Filed Under (Kawasaki) by admin on 25-10-2010

download
The first Kawasaki KZ750 twin was built in 1975 and sold as a 1976 model as a KZ750B1. For the first four years of production (1976-79), the KZ750B1 through B4 shared identical Mikuni BS38 carburetor assemblies. These assemblies are probably the heaviest twin-carb assemblies ever built and have a couple unique features. The biggest oddity is that the Kawasaki version of the BS38 uses a system where both the pilot jet and main jet are screwed into the float bowl. A good bowl gasket is critical because gas is drawn from the jets into the internal passages that lead to the venturi via channels beneath the gasket inside the float chamber. The pilot jets used are standard BS series fare in that they are Mikuni BS30/96 type but the main jets are unique to Kawasaki BS38 carburetor assemblies. They look like very small air jets and are frequently stripped as they require the correct sized small screwdriver to remove

Incoming search terms:

Incoming search terms: