2014 crf250 axel berring size

You search Auto repair manual PDF 2014 crf250 axel berring size, if there are search results will appear below. If search results do not exist, please search by others keyword.



  2014 crf250 axel berring size Direct Download speed 5282 Kb/s

  2014 crf250 axel berring size Full Version speed 6162 Kb/s



Harley-Davidson Valves, Guides And Seats Installation

0

Filed Under (Harley Davidson) by admin on 31-10-2010

download
1: Clean carbon from old guide O.D. before removal. 2: Guide to head press fit .0015″ / .002″ (head smaller than guide). 3: Heat head to approximately 200° – 250° F. 4: Install the guide at room temperature (Head hot & Guide at room temperature). 5: Let head cool to room temperature before final sizing of the bore. 6: Determine desired clearance valve to guide. Recommended clearance Shovel Head with cast iron guides Intake .001″ – .0015″ Exhaust .0015″ – .002″ (Ampco-45 add .001″) 7: Select the correct plug gage by adding the valve stem diameter and clearance desired for the finish diameter. 8: Select a plug gage .0005″ under finish size for the other end of the handle. 9: Finish hone the bore to size, check the size as you hone with the -.0005″ under size pin gage, finish hone to size with the finish plug gage pin. 10: Cut or Grind the seats, lap the valves to seats and check valve seat concentricity before assembling valve springs. 11: Use a good assembly lube, S’NS works great. 12: Use valve stem seals. Factory OE seals will stay tight with guide top size +.005″ to -.015″ from published size. 13: After the head is assembled and still on the bench check for any leakage valve to seat

Triumph Daytona 675 Fork Protectors (Front Axel Slider) Installation Instructions

0

Filed Under (Triumph) by admin on 30-10-2010

download
1. Slide from the left side (clutch lever side) the Rod assembly through hollow front axel. 2. Thread on the black bobbin and hand tighten. 3. Install self locking nut and tighten until entire assembly locks into place. No need to over tighten as the locking nut will secure the entire assembly. 4. Press on the hole plug on the left side only ( no need to remove the right side hole plug ). 5. Confirm all hardware is secure. 6. Test ride and double check hardware

2009 GAS GAS TXT PRO TECHNICAL SPECIFICATIONS AND OWNER'S MANUAL

0

Filed Under (Gas Gas) by admin on 28-11-2010

download
ENGINE 2 stroke, single cylinder, direct reed valve crankcase induction. Liquid cooled. 125 cc. engine Cylinder size 124,8 cc. Bore and stroke 54 x 54.5 mm. 200 cc. engine Cylinder size 175,3 cc. Bore and stroke 64 x 54,5 mm. 250 cc. engine Cylinder size 247,7 cc. Bore and stroke 72,5 x 60 mm. 280 cc. engine Cylinder size 272,2 cc. Bore and stroke 76 x 60 mm. 300 cc. engine Cylinder size 294,1 cc. Bore and stroke 79 x 60 mm. Carburettor, diameter of the diffusor 26 Lubrication system Mixture (50:1)(2%) Ignition system Digital magnetic flywheel CDI TRANSMISSION Transmission type 6 gears, Four / Six system by GAS GAS* (Patented). Clutch type Hydraulic command, 1/3 discs, variable progressive with diaphragm system by GAS GAS* (Patented). Driving system By chain Gear ratio 1st. 2,996 (35x27x28/16x24x23) 2nd. 2,571 (36/14) 3th. 2,187 (35/16) 4st. 2,112 (36x23x24/14x28x24) 5st. 1,125 (27/24) 6th. 0,821 (23/28)
-11- Primary reduction ratio 2,777 (75/27) Final reduction ratio 3,818 (42/11) Overall drive ratio 8,704 (6th. gear) Transmission oil Capacity 550 cc. Type 10W40 API SF o SG. FRAME Type Tubular profile made with Cr-Mo. Tyres Front 2,75 x 21″ Trial Rear 4,00 x 18″ Trial tubeless. Suspension Front Adjustable tele-hydraulic fork ø 40 mm. (125 / 200). Adjustable tele-hydraulic fork ø 40 mm with aluminium bars (250 / 280 / 300) Rear Variable progressive system with mono-shock multiadjustable. Suspension stroke Front 177 mm. Rear 164 mm. Front fork oil SAE 5. Front fork oil level ø 40 mm.(125 / 200) 180 mm. air chamber steel bar ø 40 mm. (250 / 280 / 300) 160 mm. air chamber aluminium bar BRAKES Type Disc brake. Disc diameter Front ø185 mm. 4 piston calipers. Rear ø150 mm. 2 piston calipers. DIMENSIONS Overall height 1180 mm. Overall width 820 mm. Seat height 650 mm. Ground clearance 315 mm. Wheelbase 1330 mm. Fuel tank capacity 3,1 liters.

Incoming search terms:

DETACHABLE KING SIZE WINDSHIELD FOR SOFTAIL MODELS WITH CHROME HEADLAMP NACELLE OR STREET STALKER HEADLAMP NACELLE (WITHOUT PASSING LAMPS)

0

Filed Under (Harley Davidson) by admin on 07-03-2011

download
Installation 1. Remove upper screws that attach the chrome headlamp nacelle to the front forks. 2. See Service Parts illustration. Attach the upper docking bushings (22) using washer (21) and mushroom head screws (20) Use Loctite 242 (blue) on screw threads. Torque screws to 19 ft-lbs (25.8 Nm). 3. Remove lower screws that attach the chrome headlamp nacelle to the front forks. 4a. For vehicles equipped with the Chrome Headlamp Nacelle, attach the lower docking bushing (22) using washer (21) and button head screw (23). 4b. For vehicles equipped with the Street Stalker Headlamp Nacelle, attach the lower docking bushing (22) using washer (21) and button head screw (24). Installing/Removing Windshield 1. Carefully lock bottom windshield assembly jaws into grooves of the lower rubber docking bushings. 2. Hook the top windshield assembly jaws into grooves of the upper rubber docking bushings. 3. Firmly press the windshield into place until seated on docking bushings. 4. To remove windshield, grab windshield edges on each side of center brace and firmly pull windshield loose from docking bushings. 1 WARNING Carefully inspect windshield upon completion of installation. Be sure windshield mounting does not restrict full left or full right movement of front fork assembly. Restricted movement could affect handling, resulting in personal injury. If restriction does occur, adjust windshield as needed until proper clearance is obtained. Have experienced Harley-Davidson service personnel correct any problems before riding with this accessory installed. 1 CAUTION Check mounting hardware periodically. Never ride with loose mounts. A loose mounting causes extra stress on all other mounts, as well as the windshield itself, and could result in premature failure of either or both. 1 CAUTION Do not clean Lexan®polycarbonate in hot sun or high temperature. Powdered, abrasive or alkaline cleanser will damage the windshield. Never scrape the windshield with a razor blade or other sharp instruments because permanent damage will result. Sunlight reflections off of the inside curvature of a windshield can, at certain times of the day, cause extreme heat build-up on motorcycle instruments. Exercise care in parking. Park facing the sun, place an opaque object over the instruments, or adjust the windshield to avoid reflections. Harley-Davidson windshields are made of Lexan®. Lexan®is a more durable and distortion-resistant material than other types of motorcycle windshield material, but still requires attention and care to maintain. • Do not use liquid windshield “protectors” on your windshield. Although they may work well on automobile safety glass, Harley-Davidson cannot ensure the results when used on Lexan®Harley- Davidson windshields. If you want to use a windshield protectant on your windshield, try Harley Glaze Polish and Sealant®. • Do not use benzine, paint thinner, gasoline, or other types of harsh cleaning agents on windshield. They will damage the windshield surface. • Do not use benzine, paint thinner, gasoline, lubricants (including Armorall), or other cleaning agents on the rubber bushings. They will damage the bushing surfaces

Incoming search terms:

HARLEY-DAVIDSON Starter Relay Location Guide

0

Filed Under (Harley Davidson) by admin on 18-04-2012

download
Touring 1998 – 2007 Additional Notes: Relay Location: Under Seat in rubber Boot Battery Connection: Under Seat,Visiable Installation Notes: No Access Issues Factory Relay Type: FULL SIZE Factory Relay Part #: 31504-91A Connection Type: Ground Lug to Battery + Terminial System Relay Replacement: R-S-1 Circuit: Cold C Copywrite 2005 Identity Inv. LLC As of: 11.05 ***2004 – 2007 FLHR series bikes & 2007 FLHX require additional Adaptor AD-1 & DGD-1. Start Relay is in Power Distribution box. Replaces H-D Relay part# 31579-04 Softails 2000 – 2007 Additional Notes: 2000 is when the Softails changed to Twin Cams. Relay Location: Under Seat in covered Power Distribution Box. Battery Connection: Under Seat,Visiable Installation Notes: No Access Issues Factory Relay Type: 1/2 SIZE Factory Relay Part #: 31522-00B Connection Type: Ground Lug to Battery + Terminial System Relay Replacement: R-S-3 Circuit: Cold C Copywrite 2005 Identity Inv. LLC As of: 11.05 Softails 1996 – 1999 Additional Notes: Relay Location: Under Seat in covered Power Distribution Box. Battery Connection: Under Seat,Visiable Installation Notes: No Access Issues Factory Relay Type: FULL SIZE Factory Relay Part #: 31504-91A Connection Type: Ground Lug to Battery + Terminial System Relay Replacement: R-S-1 Circuit: Cold C Copywrite 2005 Identity Inv. LLC As of: 11.05
Dyna 2007 Additional Notes: Relay Location: Under Side Panel Cover. Battery Connection: Replace Batt 15A Fuse with Supplied Fuse Holder Installation Notes: No Access Issues Factory Relay Type: 1/2 SIZE Factory Relay Part #: 31522-00B Connection Type: Tap 12v Fuse (Batt 15A) System Relay Replacement: R-S-3 Circuit: Cold C Copywrite 2005 Identity Inv. LLC As of: 11.05 Dyna 2000 – 2005 Additional Notes: Relay Location: Under Side Panel Cover. Battery Connection: Battery connection is made direct to Battery Buss to right of Relay * see Pic3 Installation Notes: Remove Outer Cover, then Remove 4 bolts holding secondary protector plate in place. Relay is on the upper left. Factory Relay Type: 1/2 SIZE Factory Relay Part #: 31522-00B Connection Type: Ground Lug to Battery Buss + Terminial System Relay Replacement: R-S-3 Circuit: Cold C Copywrite 2005 Identity Inv. LLC As of: 11.05 Pic3 Sportster 2004-2007

Incoming search terms:

Harley Davidson Softail 1987 to Current Trike Conversion Installation Manual

0

Filed Under (Harley Davidson) by admin on 05-03-2012

download
Protect yourself and others when you have a vehicle up in the air. Anytime you lift a vehicle, either by hoist or a jack, make sure that it is securely supported. b. c. d. e. f. Make sure the engine is turned off before you begin work. • Carbon Monoxide poisoning from exhaust gases: Be sure there is adequate ventilation whenever you run the engine. • Burns from hot parts: Let the engine and exhaust system cool before working on those areas. • Injury from moving parts: If running the engine, keep hands, fingers and clothing away from moving/rotating parts. Gasoline vapor and hydrogen gases from batteries are explosive. To reduce the possibility of fire or explosion, be careful when working near gasoline and batteries. Use only nonflammable solvent, not gasoline, to clean parts Never drain or store gasoline in an open container. Keep all cigarettes, sparks or flame away from the battery and all fuel related parts. 1.4 Specifications Overall Length: 66″ Body Length: 92″ Wheel Base: 53″ Load Capacity: 620 Lb Tire Size (15″): 205 / 70 / R15 Wheel Size (15″) (4 lug) Offset +35 mm 15x7JJ 4×4.5 – (Current Installations – Alum Rear End) Wheel Size (15″) (5 lug) Offset +35 mm 15x7JJ 5×4.5 – (Later Installations – Black Rear End) Tire Size (16″) 215 / 60 / R16 Wheel Size (16″) (5 lug) Offset +40 mm 16x7JJ 5×4.5 – (First Installations – Black Rear End) Tire Pressure: 20 PSI Suspension: Internal Swing Arm utilizing OEM shocks Rear Differential: Custom-built rear differential utilizing OEM drive belt. Brakes: Original front plus 2 high performance disc brakes at rear. Storage Capacity: 3.75 cubic feet. 2 full-face helmets and additional storage

Triumph SU CARBURETORS SERVICING AND TUNING

0

Filed Under (Triumph) by admin on 29-10-2010

download
Jets: These are made in various sizes ranging from.099 inches to.1875 inches, the larger sizes being used only for racing or very high performance engines. The two sizes most commonly found on production cars are the.090 inch and the.100 inch. The size of the jet will be found stamped on the jet head. The figure “nine”wilt indicate that it is the.090 inch and the figure “one”will indicate the.100 inch jet. When tuninga production car the jets size should be checked to make sure that it is of the size recommended by the manufacturers. Centering of Jet: If for any reason, the jet assembly has been removed, it will be ne cessary to recenter the jet. First, remove the clevis pin at the base of the jet which attaches the jet head to the jet operating lever. Withdraw the jet completely and remove the adjusting nut and spring, then replace the adjusting nut, without its spring, and screw it up toits highest position. Slide the Set into position until the jet head is against the base of the adjusting nut. When this has been done, find out if the piston is perfectly free by lifting it up with the finger and allowing it to drop. If the piston is not entirely free, slacken the jet screw and manipulate the lower part of the assembly, including the projecting part of the bottom half of the jet bearing, adjusting nut, and jet head. Make sure that this assembly is now slightly loose. The piston should then rise and fall quite freely as the needle is now able to move the jet into the required central position. The jet screw should now be tightened and a further check made to determine that the piston is still quite free. When complete freedom of the piston is achieved the jet adjusting nut should be removed, together with the jet, and the spring replaced. Experience has shown that a large percentage of carburetors, which have given trouble has been due to the incorrect centering of jets. Jet Needles— These are made in a great variety of sizes, probably now well over two hundred and fifty, and each type of engine hasaneedlethat has been selected, after very careful tests have been carried out, to give the best all-round performance. Most manufacturers actually give three alternative needles for each type and size of engine, these needles clearly being listed by the manufacturer “Standard”, “Rich”or”Weak”and before tuning is started the needle, which is marked on the shank should be checked against the manufacturer’srecommendation to make quite sure that the right needle is fitted; this is most important.

Incoming search terms:

Honda Goldwing GL1800 Solid Rear Axle Trike Conversion Installation Manual

0

Filed Under (Honda) by admin on 16-02-2011

download
Specifications Overall Width: 57.75″ Overall Length: 108″ Overall Length w/EZ-Steer 109.5 Wheel Base: 71″ Extended 4.5″ At Rear Axel Wheel Base w/EZ Steer 72.5″ Load Capacity: 500 Lb Tire Size: 205 / 70 / R15 Wheel Size (15″) Offset +35 mm 15x7JJ 4×4.5 Tire Pressure 20 PSI Suspension: “Zero-Flex” Internal Swing Arm utilizing 3 shocks, OEM shock absorber plus 2 coil over shock absorbers. Rear Differential: Champion Lightweight rear axle / differential assembly. Gear Ratio 2.93:1 gear ratio Brakes: Original front plus 2 high performance disc brakes at rear. Storage Capacity: 6.75 cubic feet. 3 full-face helmets and additional storage. Trike Conversion Installation Kit Honda Goldwing GL1800 Champion Trikes Page 7 of 28 Revision 10 4 Removal of Original Parts Most tasks necessary in this guide can be accomplished with the vehicle on its center stand. Secure the center stand to one of the forward crash bars with a ratchet strap to keep vehicle from rolling forward and off the center stand. Be sure that the vehicle is laterally stable as well. Remove the following from the vehicle. See OEM manual for detailed instructions. Items to be retained for return of deposit or re-installation after modification shall be duly noted. • Seat (to be re-installed without modification) • Left and right side covers (to be re-installed without modification) • Battery and battery box (to be re-installed without modification) • Left and right saddle bags • Remove taillight and locking assemblies from saddlebags (to be returned for refund of deposit) • Trunk (to be re-installed without modification) • Left and right passenger foot rests (to be re-installed without modification) • Left and right foot rest under covers (to be modified and re-installed) • Left and right rear crash bars • Saddle bag trunk stay (to be modified and re-installed) • Left and right mufflers (Mufflers only, do not remove decorative covers) • Rear wheel • Left and right pivot bolt covers (to be re-installed without modification) • Reverse resistor (to be relocated) • Swing Arm – Note : Carry out brake system modifications (Section 5) prior to removing Swing Arm. • Note : Upper bolt of mono shock can be removed without removing the fuel tank. • Note : Do not remove actuator hose from actuator pump or shock absorber. Dismounting shock actuator pump will allow more movement of shock absorber when removing swing arm.Trike Conversion Installation Kit Honda Goldwing GL1800 Champion Trikes Page 8 of 28 Revision 10 5 Brake System Modification Note : Modification to the vehicle brake system should be carried out prior to removal of the swing arm. From the manufacturer, your Honda Gold Wing brake system utilizes both front and rear brakes when the foot brake is applied. In order to insure safe operation of your Gold Wing when converted to a Champion Sidecars Trike, the brake system must be modified to isolate the front and rear brake systems from each other. Once modification is complete, four of the six pistons in the front calipers operate only when the hand brake lever is applied. The rear brakes operate only when the foot brake pedal is applied. The diagrams below outline the difference between the GL1800 OEM brake system and the system as modified by the Champion Sidecars Trike Conversion Kit.

Incoming search terms:

HARLEY DAVIDSON CHROME MASTER CYLINDER AND CLUTCH BRACKET KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 15-03-2011

download
MASTER CYLINDER REMOVAL See Figure 1. Master cylinders designed for dual disc (two caliper) operation have an 11/16 inch (17.5 mm) bore, while those that are designed for single disc (one caliper) operation have a 9/16 inch (14.3 mm) bore. The bore size is stamped (1) on the master cylinder assembly inboard of the handlebar clamp bracket. NOTE Do not use an 9/16 inch bore master cylinder assembly on dual disc (two caliper) models or dual disc 11/16 inch bore master cylinder assembly on single disc (one caliper) models. These master cylinder assemblies are not interchangeable. Using the wrong assembly can adversely affect braking efficiency or result in brake failure which could result in death or serious injury. D.O.T. 4 brake fluid will damage painted and body panel surfaces it comes in contact with. Always use caution and protect surfaces from spills whenever brake work is performed. Failure to comply can result in cosmetic damage. (00239b) 1 is 01230 1. Bore stamp size location Figure 1. Verify Correct Master Cylinder Bore Size 1. Open bleeder nipple caps on front brake caliper. Install end of a length of clear plastic tubing over caliper bleeder valves, while placing free end in a suitable container. Open bleeder valves about 1/2-turn. Pump brake hand lever to drain brake fluid. Close bleeder valve. Avoid leakage. Be sure gaskets, banjo bolt(s), brake line and master cylinder bore are clean and undamaged before assembly. (00322a) 2. Remove bolt and two steel/rubber washers to disconnect fitting of hydraulic brake line from master cylinder. Discard washers. Do not remove or install the master cylinder assembly without first positioning a 5/32-inch (4 mm) thick insert between the brake lever and lever bracket. Removing or installing the master cylinder assembly without the insert in place may result in damage to the rubber boot and plunger on the front stoplight switch. (00324a) 3. See Figure 2. Place the cardboard insert between the brake lever and lever bracket

Incoming search terms:

HARLEY DAVIDSON XLH 1200cc BIG BORE KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 06-03-2011

download
Boring and Honing Procedures 1. Check again for burrs on cylinder gasket surfaces and remove burrs before performing Step 2. 2. Install original head and base gaskets, CYLINDER TORQUE PLATES (Part Number 33446-A) and TORQUE BOLTS (Part Number 33446-4). Tighten TORQUE BOLTS following tightening procedure given in the INSTALLATION, CYLINDER HEAD procedure in the ENGINE section of the Service Manual. NOTE Torque plates, properly tightened and installed with gaskets, simulate engine operating conditions. Measurements will vary as much as 0.001 inch without torque plate. 3. The cylinder must be bored with gaskets and torque plates attached. Bore the cylinder to 0.003 inch under the desired finish size. 1 WARNING CAUTION CAUTION 1 WARNING Kit Number 4. Hone the cylinder to its finished size (See Figure 1) using a 280 grit rigid hone followed by a 240 grit flexible ball hone. Honing must be done with torque plates attached. All honing must be done from the bottom (crankcase) end of the cylinder. Work for a 60 degree crosshatch pattern. 5. See Figure 1. After machining and honing, chamfer the bottom edge of the cylinder liner. the chamfer provides a beveled surface for easier installation of the cylinder over the piston rings. Break leading edge of liner to a flat surface. The bottom edge of the liner will be somewhat sharp after machining. This sharp edge could easily be damaged during installation of the cylinder. Piston Installation The 1200cc pistons have an arrow on the top of the piston. This arrow must face the front of the engine when piston is installed. There is no front cylinder piston or rear cylinder piston. New pistons can be installed in either cylinder. Check piston rings for proper side clearance and end gap (See XLH Service Manual). Be sure end gaps of adjacent rings are installed 90 degrees apart. Assembly Follow assembly and torque specifications given in the ENGINE section of the applicable Service Manual. Replace original gaskets, O-rings and seals with new components furnished in kit. NOTE Push rod covers on 1991 and later models are one-piece and the correct O-rings are as follows: Bottom – Part Number 17944-89 Upper – Part Number 11190 Engine Break In For the first 500 miles, to wear-in critical parts, observe these few simple driving rules: During the first 50 miles, keep the engine speed below 2500 RPM in any gear. Up to 500 miles, vary the engine speed, avoiding any steady speed for long distances. Engine speed up to 3000 RPM is permissible in any gear. Avoid fast starts at wide open throttle. Drive slowly until engine warms up. Avoid running the engine at extremely low RPM in higher gears. 2 of 3 -J00001 1200cc CYLINDER FINAL BORE SIZE AFTER HONING STANDARD BORE DIAMETER 3.4980 inch + 0.0002 inch Figure 1. Bottom Edge of Cylinder Liner Chamfer i04852 Break Edge to Flat Surface

Incoming search terms: