2997 yamaha vstar 1300 dipstick lication

You search Auto repair manual PDF 2997 yamaha vstar 1300 dipstick lication, if there are search results will appear below. If search results do not exist, please search by others keyword.



  2997 yamaha vstar 1300 dipstick lication Direct Download speed 5282 Kb/s

  2997 yamaha vstar 1300 dipstick lication Full Version speed 6162 Kb/s



HARLEY DAVIDSON LCD OIL TEMPERATURE/ LEVEL DIPSTICK INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 01-02-2011

download
LCD DIPSTICK INSTALLATION 1. Remove the original equipment (OE) dipstick from the filler neck. 2. Non-threaded Dipsticks: Lightly oil the O-ring on the new LCD dipstick. Orient the dipstick so that the display window is horizontal and readable from left to right, with the Bar and Shield logo to the left (towards the rear of the motorcycle). Push the dipstick straight into the filler neck until it seats. 3. For threaded dipsticks: Lightly oil O-ring and screw into the transmission like OE dipstick. If the orientation of the display is unsatisfactory when fully seated, refer to Adjusting the Display Angle later in these instructions. NOTE To be sure of correct readings, the dipstick MUST seat firmly against the flange. LCD DIPSTICK USE AND CARE Removing the Dipstick The dipstick assembly must be removed from the filler neck to add oil or to service the internal battery. Displaying the Oil Temperature and Level See Figure 1. Press and release the rubber button on the front face to display the temperature of the oil in the oil tank in degrees Fahrenheit (°F), and the oil level. The display will automatically shut off after approximately ten seconds. Do not overfill oil tank. Doing so can result in oil carryover to the air cleaner leading to equipment damage and/or equipment malfunction. (00190a) NOTES Oil level cannot be accurately measured: • on a cold engine • with the motorcycle upright • with the engine running NOTE Oil level on 2000 through 2004 Softail models with the original dipstick is checked with the motorcycle standing upright (not leaning on the jiffy stand). THIS IS NOT THE CASE with the LCD oil temperature/level dipstick. For all 2000 and later Softail models, oil level inspection must be done with the motorcycle LEANING ON the jiffy stand, on level ground. For pre-ride oil level inspection: With the motorcycle on level ground, RESTING ON the jiffy stand : •The oil level should be as indicated in Figure 1, display 4 through 8 (bars showing oil level, and “COLD OIL” message followed by flashing oil temperature) when the engine is cold. DO NOT ADD OIL to bring the level to the FULL mark on the dipstick of a COLD engine. •If the oil level indicates as in display 9 (animated level bars, followed by an “888 NO SENSOR” code), the wires inside the dipstick may be disconnected or damaged. Refer to Replacing the Battery later in these instructions to separate the dipstick upper and lower assemblies. If the small plug next to the battery has become dislodged from the receptacle, plug it in. If a visible wire is damaged, a repair can be attempted. If no damage is visible, the dipstick is damaged internally and should be replaced. For oil level inspection at operating temperature: Ride the motorcycle until the engine is at normal operating temperature. Idle for 1-2 minutes with the motorcycle on level ground, RESTING ON the jiffy stand (except Softails) , turn the engine OFF.

Incoming search terms:

BMW K 1300 S, K 1300 R and K 1300 GT SPECIFICATION

0

Filed Under (BMW) by admin on 17-11-2010

download
The K 1300 S with 175 hp, the K 1300 R with 173 hp and the K 1300 GT with 160 hp. The new K bikes feature updated transmission and clutch assembly, plus smoother engine performance and new switchgear. Von Kuenheim continues: “By raising capacity to 1300 cc, our engineers have not only increased output but also torque on all three models. At the same time the driveline was intensively revised from air/fuel mixture formation right through to the exhaust system. In this way we have been able to optimize partial load behavior as well as throttle response. Now the clutch can be operated with even less effort and with greater refinement. Shifting has been improved tangibly due to constructional changes to the gearbox and drive.” BMW is introducing new options for the 2009 as well. The popular Electronic Suspension Adjustment that first appeared on the 2005 K 1200 S has now been updated with even more on-the-fly adjustability and it’s called ESA II. Also new is the quick-shifter option, racing-style gear shift assistant, borrowed from BMW’s race-ready HP2 Sport. Automatic Stability Control (ASC) is also offered as an option on the new K bikes. “Both the K 1300 S and also the R will also have the shift assistant – familiar from the HP2 Sport – available as an option for the first time,” von Kuenheim emphasized. “We have also advanced the chassis. The new lower longitudinal strut is now made of aluminum and is thus considerably lighter. This makes the front wheel guidance response even more sensitive. The result of this comprehensive development work is superior handling, improved rideability and lower fuel consumption. The electronically adjustable suspension – called ESA in short – was launched as a world first on the K 1200 S. Now we are presenting the new, well-proven ESA II as an option for the K Series. Apart from the suspension and damping this unique system also allows the spring rate to be adjusted at the press of a button. The K Series model revision also heralds a new and innovative generation of switches and controls.

Incoming search terms:

YAMAHA MOTOR CORPORATION, U.S.A. STREET & ENDURO MOTORCYCLE LIMITED WARRANTY

0

Filed Under (Yamaha) by admin on 27-12-2011

download
GENERALEXCLUSIONS from this warranty shall include any failures caused by: a. Competition or racing use. b. Installation of parts or accessories that are not qualitatively equivalent to genuine Yamaha parts. c. Abnormal strain, neglect, or abuse. d. Lack of proper maintenance. e. Accident or collision damage. f. Modification to original parts. g. Damage due to improper transportation. SPECIFIC EXCLUSIONS from this warranty shall include parts replaced due to normal wear or routine maintenance. THE CUSTOMER’S RESPONSIBILITY under this warranty shall be to: 1. Operate and maintain the motorcycle as specified in the appropriate Owner’s Manual. 2. Give notice to an authorized Yamaha motorcycle dealer of any and all apparent defects within ten (10) days after discovery, and make the machine available at that time for inspection and repairs at such dealer’s place of business. You may locate your nearest authorized Yamaha dealer through your local telephone directory. WARRANTY TRANSFER: To transfer any remaining warranty from the original purchaser to any subsequent purchaser, it is imperative that the machine be inspected and registered for warranty by an authorized Yamaha motorcycle dealer. In order for this warranty to remain in effect, this inspection and registration must take place within ten (10) days after transfer. Areasonable dealer imposed fee may be charged for the inspection. In no case will warranty be extended beyond the original period. EMISSIONS CONTROLSYSTEM WARRANTY Yamaha Motor Corporation, U.S.A. also warrants to the ultimate purchaser and each subsequent purchaser of each Yamaha motorcycle covered by this warranty with a displacement of 50cc or greater, that the vehicle is designed, built, and equipped so as to conform at the time of sale with all U.S. emissions standards applicable at the time of manufacture and that it is free from defects in materials and workmanship which would cause it not to meet these standards within the periods listed immediately below. Failures other than those resulting from defects in material or workmanship which arise solely as a result of owner abuse and/or lack of proper maintenance are not covered by this warranty.

Incoming search terms:

2007 Yamaha V-Star 1300 Classic Straights Installation Instructions

0

Filed Under (Yamaha) by admin on 08-11-2010

download
Stock Exhaust System Removal 1. Remove right side Foot peg assembly or Floorboard. (Whichever is applicable to your model.) 2. Remove bolts that are holding pipes at rear mounting bracket. 3. Loosen clamps at mufflers. 4. Remove mufflers. 5. Remove the two nuts that secure the rear exhaust header pipe to the rear cylinder head. 6. Remove rear exhaust pipe assembly. 7. Remove the two nuts that secure the front exhaust header pipe to the front cylinder head. 8. Remove front exhaust pipe assembly. 9. Remove exhaust-mounting bracket from frame. Hard-Krome Exhaust System Installation NOTE: Take care when fitting this Hard-Krome aftermarket exhaust system on your motorcycle. It has been designed to replace a STOCK exhaust system on a motorcycle with its engine, frame and other components in their STOCK design, configuration and location. WARNING : Re-check and re-tighten ALL fasteners and supports after 50 miles, then re-check and tighten as necessary on a periodic basis to ensure proper operation and performance. NOTE: All fasteners should be loose during initial installation to ensure proper fit and location of the new exhaust system. 1. Install new exhaust gaskets. 2. Install mounting bracket using Bolts with flat & lock washers. 3. Install Front exhaust header pipe, taking care to not scratch chrome surfaces on pipe, engine or motorcycle — use masking tape as needed. 4. Install the two nuts to secure the flange that holds the exhaust header pipe to the front cylinder head — DO NOT TIGHTEN NUTS! 5. Install Nut strip into each slotted bracket of front pipe and start the 3/8-16×3/4″ Bolt with flat & lock washer through backside of mounting bracket. — DO NOT TIGHTEN BOLTS! 6. Carefully install rear pipe. 7. Install the two nuts to secure the flange that holds the exhaust header pipe to the front cylinder head — DO NOT TIGHTEN NUTS! 8. Install Nut strip into each slotted bracket of rear pipe and start the 3/8-16×3/4″ Bolt with flat & lock washer through backside of mounting bracket. — DO NOT TIGHTEN BOLTS! 9. Tighten the two bolts that secure the rear exhaust header pipe flange. 10. Tighten the two bolts that secure the front exhaust header pipe flange. 11. Tighten front pipe bolts at mounting bracket. 12. Tighten rear pipe bolts at mounting bracket. 13. Reinstall foot peg assembly or floorboard. 14. If applicable to your model install foot peg relocating brackets and foot pegs as shown in illustration. 15. Before starting bike wipe off any fingerprints and grease off pipes. Start bike and check for any exhaust leaks. NOTE: To achieve optimum performance from your Hard-Krome exhaust system we suggest installing the Dynojet jet kit for carbureted models

YAMAHA V-STAR 1300 exhaust system INSTALLATION INSTRUCTIONS

0

Filed Under (Yamaha) by admin on 08-11-2010

download
1. Install the bracket (Stamped 439-P, supplied) to the motorcycle chassis using the 10 x 20mm hex head bolt (supplied) and two of the stock mount bolts in the bottom holes (Figure 3). 2. Remove exhaust system and heat shields from protective packaging and place them on a non-abrasive surface such as a blanket or carpet. Using a non-permanent marker or tape, mark outside edge of each heat shield to show location of mounting clips that the hose clamps will loop through (Figure 4). 3. Apply a small amount of anti-seize compound to the threads of the stock O2 sensor and install it into the header assembly. NOTE: Be careful not to overtighten or get anti-seize compound on the sensor tip as this could damage or affect the sensor function. 4. Carefully lay header assembly into the heat shields and loosely install the hose clamps #20 on head pipe heat shields and #24 on collector heat shield (supplied) by feeding the tail end of the clamp into the heat shield clips. Take note of screw head direction (Figure 5), for adjustment purposes they must be accessible when system is installed. NOTE: Do not tighten the clamps at this time. 5. Using stock dome nuts, carefully install system into exhaust ports. (Assistance may be required). NOTE: Install but do not tighten the exhaust nuts at this time. 6. Remove the muffl er heat shield and baffl e assembly from their protective packaging. Place them on a non-abrasive surface such as a blanket or carpet. 7. Insert the large hose clamp (#56, supplied) into the clip on the muffl er heat shield. 8. Carefully slide the baffl e assembly (without damaging the fi berglass packing) into the muffl er heat shield and align the holes in the heatshield with those in the baffl e. Secure the baffl e with the 1/4-20 x 1/2″ button head screws (supplied) and tighten the hose clamp. 9. Install the 5/16″ x 1 1/4″ hex head bolt, washers and locknut (supplied) in the muffl er clamp (supplied) and slip the clamp over the end of the baffl e tube. 10. Slide nut plate (supplied) inside the bracket welded to backside of baffl e (Figure 6). 11. Install the muffl er assembly onto the collector, making sure it slides forward enough to align the edge of the bracket welded to the baffl e with the edge of the mounting bracket. 12. Attach the muffl er assembly to the mounting bracket using the 5/16″ x 5/8″ fl ange head bolts (supplied). 13. Tighten exhaust port nuts evenly on both cylinders. 14. Tighten the muffl er clamp and the 5/16″ fl ange head bolts, securing the muffl er assembly. 15. Insert the O2 sensor plug back into harness and tuck harness back into its original position. Reinstall the cover. 16. Check alignment of heat shields making sure the ends meet squarely to the collector heat shield. Tighten the hose clamps on all the heat shields when properly aligned. 17. Reinstall right side passenger and rider fl oorboards and tighten the 12mm bolts. 18. Check for adequate clearance between all exhaust system components and motorcycle accessories prone to heat damage. 19. All hardware must be properly tightened and the exhaust pipes thoroughly clean before starting motorcycle

YAMAHA XVZ 1300 Royal Star/ Venture SPEEDOMETER COWL INSTALLATION INSTRUCTIONS

0

Filed Under (Yamaha) by admin on 07-11-2010

download
Speedometer Cowling Chrome 1 2 Alcohol Wipe 1 NOTE: Allow time for the 3M® brand quality tape to cure for 24 hours at 19-32° C before washing or waxing the motorcycle. INSTALLATION 1. Position the Speedometer Cowl in front of the Speedometer. The Cowl attaches to the Speedometer Cover, not on the rubber ring around the Speedometer. The Cowl should be symmetrically located in relation to the Speedometer, use the Speedometer markings as a reference. 2. Remove the red backing tape from the adhesive strip on the base of the Speedometer Cowl. 3. Position the Speedometer Cowl as done in step 1. Make any position adjustments now. 4. Firmly press the Speedometer Cowl in place on the Speedometer Cover. 5. Allow twenty-four hours for the adhesive to fully set before washing or waxing.

Incoming search terms:

1300 Yamaha V-Star Installation Manual

0

Filed Under (Yamaha) by admin on 07-11-2010

download
1) Place motorcycle on a firm level surface and secure in a upright position. 2) Remove saddle bags and saddle bag hardware (Tourer model only) Also remove rear riders pegs (Tourer model requires removal of rear footpeg offset hardware as well) 3) Attach bracket A (right) / B (left) to rear footpeg attachment point using new bolts provided. Remount footpegs/saddlebag hardware over top of brackets A/B. NOTE: Do not attach leveling stand bracket at this time 4) Attach bracket C(right) / D(left) to rear fender sub frame using new bolts provided. (Tourer model only – Saddle bag hardware mounts to the outside of brackets C/D. Brackets C/D mount between chrome side rail and saddlebag hardware.) NOTE: Brackets C/D have welded spacers which attach in toward rear fender 5) Attach top of Bracket E(right) / F(left) to rear of brackets C/D. Brackets E/F mount to the inside of brackets C/D. NOTE: Use ½ inch spacer between brackets E/F and C/D on Tourer model ONLY
6) Attach rear of brackets A/B to TOP of forward hitch arms. Attach bottom to brackets E/F to rear hitch plate. 7) Carefully tighten all bolts at this time ensuring hitch is square with motorcycle. Hitch Bracket Identification Leveling stand screw jack installation 1) Attach leveling stand brackets to brackets A and B 2) Thread right side screw jack into threaded hole on leveling stand bracket attached to bracket A sand adjust leveling jack bolt out. 3) Push motorcycle over from left side until right screw jack is touching floor. 4) Thread left side screw jack into threaded hole on leveling stand bracket attached to bracket B and adjust out until motorcycle will rest upright on both screw jacks. 5) Adjust screw jacks until motorcycle is level. 6) After InstaTrike is attached to or removed from receiver hitch, be sure to remove leveling stands and leveling stand brackets. CAUTION – Use screw jacks to hold motorcycle upright and level ONLY. Do not lift motorcycle with screw jacks. CAUTION – Use care when installing screw jacks. Be certain that motorcycle is always in a stable balanced position.
INSTALLATION OF THE TOW-PAC HITCH CART. 1. Place your motorcycle on a smooth flat surface, like a garage floor, and install leveling stands. Install right leveling stand first. Carefully raise motorcycle off of side stand and install left leveling stand. Caution – Use leveling stands to level motorcycle ONLY. Do not raise motorcycle with stands Caution – Be certain that motorcycle is always in a stable balanced position when installing leveling stands. 2. Assemble the axles, tires and wheels, and fenders onto the tow- pac hitch cart. 3. Carefully align the tow-pac hitch cart’s hitch mount with the receiver hitch on the motorcycle. Now push the hitch mount into the receiver hitch. (this might be a little difficult until you get use to doing it. Removing the paint from the hitch mount and applying a little grease will help.) 4. Place the hitch pin through the receiver hitch and hitch mount ( alignment plate ). Install and tighten the tension bolt

Incoming search terms:

YAMAHA FJR 1300 2006 GPS-Halter INSTALLATION MANUAL

0

Filed Under (Yamaha) by admin on 10-01-2012

download
Mounting Instructions SW-MOTECH products should be installed by a qualified, experienced motorcycle technician. If you are unsure of your ability to properly install a product, please have the product installed by your local motorcycle dealer. SW Motech takes no responsibility for damages caused by improper installation. All screws, bolts and nuts, including all replacement hardware provided by SW-MOTECH, should be tightened to the torque specified in the OEM maintenance manual for your motorcycle. If no torque specifications are provided in the OEM maintenance manual, the following torques may be used: All screws, bolts and nuts should be checked after driving the first 50 km to ensure that all are tightened to the proper torque. Medium strength liquid thread-locker (i.e., “Locktite”) should be used to secure all screws, bolts and nuts. Alle vom Motorrad gelösten Schrauben sind gemäß Herstellerangaben wieder

Yamaha V-Star 1300 Receiver Hitch Installation

0

Filed Under (Yamaha) by admin on 01-01-2012

download
Install all bolts loosely until all brackets are in place Remove accessories (saddle bags, back rests, etc) before hitch installation. 1) Place motorcycle on a firm level surface and secure in a upright position. 2) Remove saddle bags and saddle bag hardware (Tourer model only) Also remove rear riders pegs (Tourer model requires removal of rear footpeg offset hardware as well) 3) Attach bracket A (right) / B (left) to rear footpeg attachment point using new bolts provided. Remount footpegs/saddlebag hardware over top of brackets A/B. NOTE: Do not attach leveling stand bracket at this time
4) Attach bracket C(right) / D(left) to rear fender sub frame using new bolts provided. (Tourer model only – Saddle bag hardware mounts to the outside of brackets C/D. Brackets C/D mount between chrome side rail and saddlebag hardware.) NOTE: Brackets C/D have welded spacers which attach in toward rear fender 5) Attach top of Bracket E(right) / F(left) to rear of brackets C/D. Brackets E/F mount to the inside of brackets C/D. NOTE: Use ½ inch spacer between brackets E/F and C/D on Tourer model ONLY
6) Attach rear of brackets A/B to TOP of forward hitch arms. Attach bottom to brackets E/F to rear hitch plate. 7) Carefully tighten all bolts at this time ensuring hitch is square with motorcycle.

YAMAHA XVS 1300 A INSTALLATION AND OWNER'S MANUAL

0

Filed Under (Yamaha) by admin on 13-01-2012

download
Place motorcycle on flat and level ground with side stand securely in place. Before installing fasteners we recommend you apply a small amount of Loctite ®medium strength #243 thread retaining compound (or similar brand) to the threads of the button head screws (a) referenced on page 3 and to the M8 x 50 fasteners supplied in Bag 914. (Thread Lock) INSTALLATION OF EYEBROW 1. Start on right side of the motorcycle and remove the 2 bolts from the fender and trim rail. Remove rear trim rail. Store bolts and trim rail, they will not be re-used. (5mm Hex Wrench) SPOOL ASSEMBLY, FRONT AND REAR 2. Assemble front and rear spool assemblies into the right eyebrow (4) and fender. Do not fully tighten. This will allow some movement which aids in the side plate installation. (5mm Hex Wrench) Figure 1. After final assembly fender mount screws will torque to: 22 Nm (17 ft/lb) 3. Repeat steps 1-2 for the left side fender assembly

Incoming search terms: