35496 module instruction

You search Auto repair manual PDF 35496 module instruction, if there are search results will appear below. If search results do not exist, please search by others keyword.



  35496 module instruction Direct Download speed 5282 Kb/s

  35496 module instruction Full Version speed 6162 Kb/s



Ignition Upgrade Module for 2004-up Carbureted Harley Davidson Motorcycles Owner's Manual

0

Filed Under (Harley Davidson) by admin on 25-11-2010

download
1. Disconnect the negative battery cable. 2. Grasp the sides of the electrical caddy (located next the ignition coil) and pull outward to remove. 3. Remove the relay and fuse panels from the electrical caddy. a. Insert a small screwdriver into the slot under each fuse and relay panel. b. Using a screwdriver, disengage the panel from the electrical caddy. 4. Disconnect the main fuse connector from the electrical caddy a. Remove the main fuse from the connector b. Insert small screwdrivers into the slots on each side of the main fuse c. Depress the tabs of the main fuse connector to disengage it from the electrical caddy
Thunder Heart Performance Corp. 615-672-8811 www.thunder-heart.com 2 EI5075.doc 5. Depress the tab located on the electrical caddy securing the TSM/TSSM. Pull it from the electrical caddy. Disconnect the TSM/TSSM connector. 6. Slide the data link connector towards the front of the motorcycle to disengage it from the electrical caddy. 7. Disconnect the ignition control module connector. 8. Disconnect the ignition coil connector and spark plug cables from the coil. 9. Remove the electrical caddy fasteners (3 total). 10. Remove the wiring from the electrical caddy. 11. Remove the fasteners securing the factory ignition control module from the electrical caddy. 12. Installation of the Digital Ignition Module is the reverse of removal. 2.2 Touring Models 1. Disconnect the negative battery cable. 2. Remove the right saddlebag. 3. Gently pull the side cover from the frame downtubes (no tools required). 4. Depress the external latches and use a rocking motion to remove the electrical connector from the ignition control module. 5. Remove the two socket screws to detach the ignition control module from the electrical bracket. 6. To install the Digital Ignition Module, install and tighten the socket screws to 50-60 in-lbs . The remainder of installation is the reverse of removal. 2.3 Softail Models 1. Remove the seat. 2. Disconnect the negative battery cable. 3. Remove the two screws to free the ignition control module from the mounting bracket. 4. Depress the external latches and use a rocking motion to remove the electrical connector from the ignition control module. 5. To install the Digital Ignition Module, install and tighten the socket screws to 15-21 in-lbs . The remainder of installation is the reverse of removal

Incoming search terms:

Victory LED Brake Light Module Installation

0

Filed Under (Victory) by admin on 31-10-2010

download
Brake Module Installation: Locate the Auto Cancel Module (ACM) under the seat on the right side of the battery box area. Select a suitable location to mount this product near the ACM module. Disconnect negative terminal on battery before installation.. Do not attached attach the product at this time. Setup: Set dip switches according to the chart below. Switch Settings: 1 2 3 4 Result OFF OFF OFF OFF 3 Flashes-Solid-Repeat ON OFF OFF OFF 3 Strobes-Solid-Repeat OFF ON OFF OFF 3 Strobes -Solid ON ON OFF OFF 3 Flashes – Solid OFF OFF ON OFF Variable Flash Rate – Use Pot to adjust flash rate Route and connect the wires as follows: Refer to block diagram on page 2. Locate the White with Pink Tracer wire leading into the ACM module. Cut this wire approximately 2-3 inches from the ACM module. A: Red: Input: Connect this wire to the cut White/Pink wire leading away from the ACM module using supplied posi-tap. (See enclosed instructions for Posi-Tap) B: Yellow: Output: Connect this wire to the cut White/Pink leading into the ACM module using supplied posi-tap. C: Black: Ground: Connect this wire to a good bare metal contact or negative terminal of battery using supplied terminal ring, crimp terminal ring onto black wire, heat terminal ring to form with heat gun or hair dryer until heat shrink, shrinks. Attach the unit to your vehicle using supplied 3M tape or tie wraps. Reconnect negative terminal to battery. Operation: Apply power and check that LED(s) operate correctly in both running light and brake light mode. Caution! This product is designed for use on DC motorcycle applications with negative ground only! This product is not recommended or approved for any other application. Warning! This product is intended to drive high output LEDs ONLY. Do not connect this product’s output to any other type lamp. Maximum output current is 2 amps. Overloading, improper use or improper operation of this product will void the warranty and many damage the product. Warning! Consult your owners’ manual or the vehicle manufacture before installing this or any other electronic product

Harley-Davidson Softail, Touring, Dyna, Sportster and V-Rod, SELF LEARNING MODULE INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 17-04-2012

download
STEP 1 – BATTERY CONNECTION Locate the battery and disconnect the negative battery cable. Mount the module in the open area in front of the battery with 2-tie straps or velcro straps, directing the harness from the module towards the 6 o’clock position. STEP 2 – THROTTLE POSITION SENSOR (TPS): Remove the air cleaner assembly and unplug the TPS sensor connector at the TPS sensor. The harness includes (2) TPS connectors which should be routed under the gas tank into the factory wire loom to the TPS sensor. The TPS sensor is located on the left side of the throttle body. Plug the (2) TPS connectors from the module in between the TPS sensor and to the factory TPS connector. STEP 3 – O2 SENSOR: Systems equipped with factory O2 sensors Rear: Unplug the Rear O2 sensor connector from the factory harness, which is located at the Rear exhaust pipe. Route the module’s harness which includes (2) O2 sensor connectors and connect one connector to the Rear O2 sensor and connect the other connector to the main factory O2 sensor connector. Front: Unplug the Front O2 sensor connector from the factory harness, which is located at the Front exhaust pipe. Route the module’s harness which includes (2) O2 sensor connectors, and connect one connector to the Front O2 sensor and connect the other connector to the main factory O2 sensor connector. Systems not equipped with factory O2 sensors NOTE: Many aftermarket exhaust systems are now equipped with plugged O2 sensor bungs which can be removed to accept an aftermarket O2 sensor. Typically these bungs already have a thread size of 18 mm x 1.5 mm. Exhaust systems not equipped with O2 sensor bungs need to have the supplied 18 mm x 1.5 mm thread size bung welded to the exhaust pipe in order to install an O2 sensor. The O2 sensor bung should be installed 3 to 6 inches away from the rear cylinder exhaust port and in front of the exhaust torque tube pipe area. The module prefers to receive information from the O2 sensor from an area that is NOT contaminated from atmospheric air. This air may enter through the tail pipe of an unrestricted or un-baffled exhaust pipe. The bung should not be installed in the “5 to 7 o’clock” area. If mounted in this area the O2 sensor can be damaged. The moisture from the gases exiting from the rear cylinder exhaust port will harm the ceramic shell element of the O2 sensor.

HARLEY DAVIDSON IGNITION MODULE INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 23-03-2012

download
Step 1: Apply a thin coat of silicone grease to the bottom of the module before mounting the module to its plate in the distributor. Step 2: Slide the three wires from the MODULE, through the grommet, to outside the distributor housing. Put the three wires from the MODULE in the TERMINAL PIN HOUSING: GREEN WIRE in hole #1, BROWN WIRE in hole #2, RED WIRE in hole #3. Plug the three wire harness (PN 29349, not supplied with this kit) into the TERMINAL PIN HOUSING. RED WIRE: Power/voltage for the MODULE. Connect to coil (+) terminal. GREEN WIRE: Ignition trigger. Connect to coil (-) terminal. BROWN WIRE: Ground for the MODULE. Connect to ENGINE BLOCK GROUND. Clean away any grease, oil, and paint from the mounting surface before the connection is made.

DIAGNOSTIC TESTER CONTROLLER AREA NETWORK (CAN) INTERFACE MODULE

0

Filed Under (Toyota Manuals) by admin on 30-10-2011

download
Remove the original DLC3 Cable and store it in the Diagnostic Tester storage case. 2. Connect the CAN Interface Module to the DLC Cable. 3. Use the Diagnostic Tester with the CAN Module installed for all DLC3/J1962 based vehicle communication. 4. If you experience problems with the Diagnostic Tester or CAN Interface Module, please contact Toyota Special Service Tool Customer Support at 1-800-933-8335. NOTE: There is no need to remove the CAN Interface Module when working with non-CAN systems or older software versions (Version 10.1a or earlier). The Diagnostic Tester will communicate with all DLC3/J1962 based systems with the CAN Interface Module installed. For DLC1 and DLC2 communication you must continue to use the Vehicle Interface Module (VIM)

Harley-Davidson Electronic Ignition Module Installation instructions

0

Filed Under (Harley Davidson) by admin on 23-04-2012

download
Step 1: Switch main dashboard switch to “off” position (Ignition& light switch) Step 2: Disconnect negative (ground) cable from the Battery Step 3: Remove the Condenser and Breaker points from the circuit breaker timing base. Step 4: Disconnect advance/ retard cable from timing base Step 5: Remove timing base from timer shaft and housing (see your manual for instructions) Step 6: Remove circuit breaker wire stud or circuit breaker to coil wire assembly from timing base Step 7: Remove circuit breaker wire from Ignition coil, and mark terminal on coil with piece of tape. Step 8: Install the Electronic Ignition Module on the timing base. Mount this short black wire to one on the timer base screws by keeping some slack in this wire so the timing base can turn free. Solder the flag terminal to this short black wire and mount it under the timer to motor bolt. This way of mounting provides a much better grounding. Do NOT use the screws (number 1 or 2 screws from picture below) from the timing base!!!! Step 9: Now three wires pass this hole via the rubber grommet. Figure 1 Figure 2 Step 10: Reinstall the timer base on the timer shaft housing, and keep some slack in the wires before protruding the hole in the timer shaft housing, and secure with ground spring and cover retainer. Reconnect the advance/retard cable to the timer base. Step 11: Route the two long wires to the ignition coil. Check in the HD service manual for a proper route to the ignition coil. (Keep away from hot surfaces like exhaust systems). Cut the wires to the exact length necessary for mounting. Step 12: Determine the exact length of the wire loom. Keep in mind that one end of the loom enters the timer shaft housing by 1cm. Cut the loom to the proper length. Step 13: Insert both wires in the loom. Strip both wire ends and solder the two flag terminals on the wires. Step 14: Connect the red wire to the ignition coil, on the terminal where the 6 or 12 volt is supplied to. This terminal has at minimum one wire connected which runs to the main switch. Step 15: Connect the black wire to the ignition coil on the terminal which is empty, and has piece of tape on it. (Old place where the circuit breaker wire was connected to) Step 16: Install the trigger rotor on the timer shaft cam, and tighten the hex screw by using the hex key tool. Do not over tighten the screw! Step 17: Check for clearance between trigger rotor and Electronic Ignition Module. Appropriate clearance is between 0,5mm and 1,5mm . Minor adjustments can be made by unlocking the two screws and slightly shift/move the Electronic Ignition Module. Check if the rotor moves free. Timing instructions: Remove the spark plugs from the engine, but keep them connected to the spark coil cables and engine ground. This enables normal operation of the spark, and prevents unwanted engine firing on compression stroke. See service manual or handbook for timing instructions of your model Step 18: Reconnect the negative (ground) cable to the battery. Step 19: Switch main power to “on” position. The red light in the Electronic Ignition Module might already light up. If not, turn the kick starter slowly. The red light is on while charging (closed points)the Ignition coil, facing solid metal of the trigger rotor. The light goes off (open points) when the end of the solid surface of the trigger rotor passes the centre of the Electronic Ignition Module. At that point a spark is generated by the coil

Incoming search terms:

ULTIMA IGNITION MODULE AND KIT INSTALLATION MANUAL FOR HARLEY DAVIDSON

0

Filed Under (Harley Davidson) by admin on 03-03-2011

download
Disconnect battery. 2. Mark location of timing plate in relation to inside of cam cover. This will give a starting point for timing on new module. Remove old ignition if applicable (see manual) Clymer, Haynes. 3. If your bike is not equipped with timing rotor M/W# 53-528 OEM#32402-83 you must buy one (included in kit). Also a single fire coil is needed (included in kit) M/W# 53-632. Any single fire coil rated 2-4 ohms can be used. NO SOLID CORE PLUG WIRES (copper, silver) they will damage the unit. 4. Install module: helpful hints, early model nose cones, i.e. Shovel Heads, the hole for the wire may need to be drilled out. Align with previously scripted mark for timing. Use lockwashers for stand offs for correct clearance of cover plate. Run wire loom. 5. Connect wires, see wiring diagram. Tape unused wires, green or brown. 12v to tach (brown) will damage module. Set timing. 1996 and later should not be timed 20˚ BTDC as the OEM module, but at 35˚ BTDC. Use this mark when using timing light. If VOESswitch is not used you must ground VOES wire (green) while timing. Refer to manual for correct identification of timing marks. At start up and timing, set spark advance in middle position. FUNCTION SWITCHES LED timing indicator light: When out, shows TDC. When ignition is on, LED will light up. When engine is cranking LED will blink. Electric Start/Kickstart: Set accordingly. VOES/Race mode: VOES switch lets the motor run smoother and improves gas mileage. If you don’t use it or add one tape up green wire and switch to race. VOES switch to use, M/W# 53-652. Spark advance: High compression motors should use race mode and 93 octane or better gas. Changing from VOES to race changes advance curves. Agood rule of thumb is if the engine knocks when throttle is applied in high gear, turn back spark advance curve until it stops engine knock. RPMlimiter: Set at desired RPM to cut engine power. Rear Cylinder: This is for racing and should be set at a dyno. +/-5˚. Rear cylinder timing is achieved through this adjuster. Most should dial to middle setting and leave alone. After all switches are set, install cover with supplied gasket and feel the increased performance of a solid state single fire ignition. Again, we remind you, if you don’t feel confident about installing this unit, let a qualified mechanic do it and be assured you are getting the best performance and gas mileage possible.

Incoming search terms:

RIVCO POWERMASTER EFI MODULE Installation AND Tuning Manual

0

Filed Under (Tips and Review) by admin on 29-01-2011

download
Locate the fuel injectors and their connectors on the intake manifolds between the “V” of the engines cylinders. You may remove the fuel tank to gain easy access to the plugs or you can make the connections with the tank on as follows. Remove the rear fuel tank mounting bolt and loosen the front two bolts. Lift the rear of the tank as high as possible (2-3 inches) and place a piece of wood between the tank and frame to hold the tank up. 2. Mounting the POWERMASTER™ EFI Module. While you can mount the module most anywhere it is recommended to mount it under the right hand side cover for easy access when making adjustments. Find a suitable surface to mount the Velcro Adhesive Square supplied. Clean the surface with rubbing alcohol, peel the backing and press firmly in place. Press the Module onto the Velcro. Route the wires with the plugs for the injectors between the frame rails and up toward the injectors with the other wires located on the backbone of the frame. If yours is a model with wires and plugs for the oxygen sensors route these wires downward with the short lead going to the plug on the rear exhaust pipe (about 6″ from the cylinder head) and the longer following along the right frame tube under the engine and forward to the front oxygen sensor and its plug.3. Connect the wires to the injectors under the fuel tank as follows. Unplug the bike’s wire harness from the injectors. Connect the male and female connectors from the injectors and the wire harness to the RIVCO POWERMASTER™ EFI Module. This places it electrically between ECU and the injectors. Repeat this process for each injector. NOTE it does NOT matter which lead goes to which injector.

Twin Tec Installation Instructions for TC88A-IH Ignition

0

Filed Under (Tips and Review) by admin on 29-11-2010

download
INSTALLATION ON 2004 MODELS 1. Turn off the ignition switch and disconnect the battery ground cable before proceeding. 2. Refer to Figures 2 and 3 for wiring details. 3. Remove the Gill Module. 4. Cut off the OE 18 terminal AMP connector used with the Gill module. Refer to the terminal list. Crimp new Deutsch terminals on the wires, and install into the 12 terminal Deutsch connector required by the TC88A-IH module. 5. Install the new TC88A-IH module. 6. Reconnect the battery ground cable. INSTALLATION ON 2005 AND LATER MODELS 1. Turn off the ignition switch and disconnect the battery ground cable before proceeding. 2. Refer to Figures 4 and 5 for wiring details. 3. Remove the Gill Module. 4. Cut off the OE 18 terminal AMP connector used with the Gill module. 5. The crankshaft position (CKP), MAP, and engine temperature (ET) sensor share a common ground Daytona Twin Tec LLC, 933 Beville Road, Suite 101-H, S. Daytona, FL 32119 TC88A-IH (386) 304-0700 www.daytona-twintec.com 10/2009 Page 2 return. This is not compatible with the TC88A-IH and some rewiring will be required. The temperature sensor is not used, but does not require removal. 6. Trace the BK/GN ground return wires from terminal B of the ET sensor and terminal A of the MAP sensor to where they join the BK/GY ground return wire from the CKP sensor. Cut the ET and MAP sensor ground return wires off at this point. You can tape up the ground return wire from the ET sensor – this wire will not be used. 7. Extend the ground return wire from terminal A of the MAP sensor up to the ignition module, crimp on a Deutsch terminal and install in position 4 on the Deutsch connector. 8. Refer to the terminal list. Crimp new Deutsch terminals on the remaining wires, and install into the 12 terminal Deutsch connector required by the TC88A-IH module. 9. Use a DVM to verify isolation (no continuity) between terminals 4 and 9 on the Deutsch connector. 10. Verify continuity between terminal A at the MAP sensor and terminal 4 on the Deutsch connector. 11. Verify continuity between terminal 2 at the CKP sensor and terminal 9 on the on the Deutsch connector. 12. Install the new TC88A-IH module. 13. Reconnect the battery ground cable. Terminal List for American IronHorse Ignition Conversion TC88A Deutsch Connector OE AMP Connector Signal Wire Color Code 1 2 +12V Power W/R

Incoming search terms:

MODEL 8100 HID/ HALOGEN MOTORCYCLE HEADLIGHT INSTALLATION

0

Filed Under (Tips and Review) by admin on 29-11-2010

download
1) Remove seat. 2) Refer to service manual to locate the following wires: An ignition signal that has power while the ignition is in the “ON” position. Terminal 30 on start relay . A “CRANK” signal (start signal) that has power while the starter motor is being activated. Terminal 86 on start relay . 3) Locate a mounting position for the module that will fit in front of or next to the battery. DO NOT MOUNT the module until all connections to the module have been made. 4) Verify the operation of the ignition and crank signals using the voltmeter or test light. Disconnect battery and make the following connections: • Connect the Blue wire from the lamp module to the ignition feed wire Terminal 30 on start relay . • Connect the Grey wire from the lamp module to the starter crank feed Terminal 86 on start relay . • Connect the Red wire from the module to one end of the fuse harness provided in the kit. • Crimp a ring terminal to the other end of the fuse harness (for connection the POSITIVE battery terminal) . • Crimp a ring terminal to the Black wire from the module. This will need to be routed to the NEGATIVE terminal of the battery • Do not in any way (lengthened or shortened) . Ensure that the ballast is close enough to the lamp to use the length of cable provided. 5) Securely mount ballast in chosen location. Plug the 2 wire sealed connector (RED AND BLACK 16 AWG WIRES) to the ballast. Route the Red and Black wires along the frame, and follow the harness under the fuel tank (recommended) to the battery compartment. Connect the Orange wire from the lamp module to the red wire from the ballast using connector. Crimp ring terminal to black wire coming from the ballast, and connect to the NEGATIVE battery terminal. • IT IS NOT RECOMMENDED THAT THE BALLAST BE MOUNTED IN CLOSE PROXIMITY TO ECU OR FUEL INJECTION WIRING. • Do not mount near sources of high heat (i.e. Cylinder head or exhaust manifold) . • Do not mount in a location where there is a possibility of mechanical interference from moving parts (i.e. Steering components or linkage) . • There is a 3-foot length of cable provided for connection between the BALLAST and the HID LAMP. This cable MUST NOT be modified in any way (lengthened or shortened) . Ensure that the ballast is close enough to the lamp to use the length of cable provided

Incoming search terms: