40 drilling rigs srl mail

You search Auto repair manual PDF 40 drilling rigs srl mail, if there are search results will appear below. If search results do not exist, please search by others keyword.





Kawasaki Fairing-Mount Light Housings Installation Manual

0

Filed Under (Kawasaki) by admin on 25-10-2010

download
1. Locate the recessed area of the fairing, directly below the headlight. 2. Position the RIGHT light housing in this area. This light housing is correctly positioned when the label panel is centered directly below the headlight. 3. With the housing in it’s proper mounting position, insert the transfer punch into the center mounting hole located in the middle of the label panel. Carefully mark the center mounting hole drilling area. 4. Remove the headlight and the headlight bucket so that the backside of the drilling area can be accessed. Reach into the fairing and move any and all wires that might be damaged by the drilling process. 5. Using the 13/64″ drill bit, carefully drill through the fairing at the location marked with the transfer punch. Return the housing to it’s mounting location and insert the supplied machine screw through the center mounting hole in the label panel. While holding the housing and screw in position, reach into the fairing and place a flat washer and stop nut onto the screw. Gently tighten this nut until the housing is snug. WARNING! The fairing material can easily be damaged by excessive stress exerted upon the fiberglass fairing material. Tightening the nuts used in mounting these fairing light housings beyond an appropriate level will crack or fracture the fairing! DO NOT OVER-TIGHTEN! 7. Locate the right-rear mounting hole on the housing. Insert the transfer punch into this mounting hole and carefully mark the right-rear mounting hole drilling area. Reach into the fairing and move any and all wires that might be damaged by the drilling process

Incoming search terms:

HARLEY DAVIDSON VRSCF LUGGAGE RACK KIT REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 10-03-2011

download
REMOVAL 1. See Figure 1. Remove four rear fender mounting bolts (1) and washers (2). If necessary, move the ECM to access the four fender mounting bolts. 2. Disconnect the tail lamp following the instructions in the appropriate service manual. 1 2 is05463 1. Bolt (4) 2. Washer (4) Figure 1. Fender Mounting Bolts INSTALLATION NOTE There are bosses molded into the inside of the fender to use as the hole drilling templates. 1. See Figure 2. Apply masking tape to the outside painted surface of the fender at the three hole locations (1 and 2). This will protect the painted surface during the drilling operation. 2. Put the fender on a work bench, painted surface down. Use clean, soft cloth between the fender and the work bench to protect the paint finish. NOTES Drilling each hole in the fender is a two-step procedure that requires a specific type of drill bit to avoid damaging the fender. 3. See Figure 2. Use a 1/2-inch spade bit or 1/2-inch unibit (do not use a spiral-type drill bit) to drill three holes from the inside of the fender through the three pilot hole bosses (1 and 2). Stop drilling when the tip of the bit just pierces the outside surface of the fender. 4. Turn the fender over so the painted surface is now facing up. Complete each hole by using the same 1/2-inch drill bit at each of the pierced holes. Clean excess material from the holes and clean the fender surface of any debris. 5. See Figure 5. Remove the masking tape from the holes and apply the protective tape (3) to the painted surface using the drilled holes for alignment. 6. See Figure 3. Put the luggage rack (1) upside down on the work bench and align the holes in the luggage rack with the holes in the fender (2).

Honda GL1100/ 1200 Saddlebag Bent Rails Installation Manual

0

Filed Under (Honda) by admin on 28-02-2011

download
Read instruction thoroughly before installing. DRILLING REQUIRED. 1. Place bike on center stand. 2. Place masking tape on feet of rail to prevent scratches on the saddlebags. Position saddlebag rails on saddlebag to mark for drilling. 3. When positioning the rail, carefully move the rail back and forth until proper alignment is achieved and there is no interference with the saddlebag latch. 4. Mark position for drilling holes on a piece of masking tape placed on the saddlebag under each leg. 5. Drill a 6mm hole. 6. Remove tape from rail and clean the saddlebag if necessary. 7. Attach the rail with the hardware included from the inside of the saddlebag lid. 8. Repeat on other side.

Incoming search terms:

HARLEY DAVIDSON FLHTCUTG MUDFLAP KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 28-03-2011

download
INSTALLATION 1. See Figure 1. Center drilling template on the rear fender. Adjust template to the bottom edge of the fender and tape template to fender. 2. Center punch the two template drilling locations. NOTE Use caution to prevent damage to the tire when drilling the attachment holes for the mudflaps. 3. Use a 5/16 inch bit to drill the template holes. 4. See Figure 2. Install the mudflap using one stud, washer and nut in each fastening hole. Tighten to 5-10 ft-lbs (6.8- 13.6 Nm) . 5. Repeat Steps 1-4 for the opposite fender.

HARLEY DAVIDSON TOUR-PAK KIT INTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 07-02-2011

download
INSTALLATION 1. Remove the rubber mat from the bottom of the Tour-Pak. 2. See Figure 1 and Table 1 to determine the proper hole configuration to attach the Tour-Pak to your luggage rack. Holes will be drilled as explained in Step 3 in the hole location for your luggage rack. Table 1. Luggage Rack and Hole Configurations Hole Configura- tion Luggage Rack C (3 holes) Stock 1997 B (4 holes) Detachable luggage rack 53107-96 A (5 holes) Luggage rack 53118-97A and luggage rack 53118-98 A (5 holes) Stock 1998 and later racks A (5 holes) Detachable Tour-Pak rack 53276-04 B (4 holes) Solo detachable Tour-Pak rack 53655-04 B (4 holes) Detachable Tour-Pak rack 53066-00B B (4 holes) Solo detachable Tour-Pak rack 53559-04A A (5 holes) Solo detachable Tour-Pak rack 53260-02 -J03631 1 of 3 B 1 A C 2 2 2 is00163 1. Front of motorcycle 2. Bottom view of Tour-Pak interior (rubber mat removed) Figure 1. Hole configurations for Tour-Pak attachment NOTE Drilling holes in Tour-Pak without wood underneath each hole site may result in the leather becoming damaged during the drilling process. 3. Place blocks of wood underneath the Tour-Pak where the holes will be drilled to prevent damage to the leather while drilling. Use the pre-drilled holes in the metal base as a guide and carefully drill the holes through the leather in the proper location using a 11/32 inch drill bit. 4. See Figure 2. For detachable luggage racks (53107- 96, 53066-00B and 53276-04): Install black cover tube to the front bar (1) of the luggage rack, as shown. This tube is used to provide a cleaner look. The black cover tube is not for use with other luggage racks. 5. Attach Tour-Pak to rack using the mounting screws provided in the Luggage Rack kit. Put bolt through from inside of Tour-Pak. Tighten screws to specifications found in the Luggage Rack kit. 6. Place the black rubber mat on the bottom of the Tour-Pak. 7. If luggage rack was removed, reattach to motorcycle according to kit instructions or Service Manual instructions

2010 Toyota Motorsports/ TRD USA Contingency Award Program

0

Filed Under (Toyota Manuals) by admin on 29-09-2011

download
To enroll in the program, complete the registration form included in the enclosed material and mail, fax or e-mail it to TRD per the instructions at the bottom of the form. Contact personnel are listed on the attached 2010 Contingency Award Guidelines sheets. These people are available to assist you throughout the year. Parts Ordering: If you are planning to order Toyota parts during 2010 you must supply us with your Visa or Master Card credit card number at the time you register in the program. There is a line on the registration form for this number. See the attached Parts Ordering Guidelines for detailed information on how to order parts. TRD is looking forward to working with each of you, and we wish you a very successful year with your racing program

Incoming search terms:

HARLEY DAVIDSON CHROME SADDLEBAG LID TRIM KIT INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 08-02-2011

download
INSTALLATION 1. Remove all articles from inside, then thoroughly wash and dry the saddlebag lid. 2. Close the saddlebag lid. Cut a piece of masking tape at least 10 inches (25 cm) long and lay it lengthwise down the center of the top outer surface of the lid starting at the front. Mark a line lengthwise down the tape, measuring an equal distance from each side so the line is centered on the lid. 3. Obtain the template (7) from the kit, and position it on the line, with the short leg held against the front surface of the lid. Carefully mark the tape at the two arrows, then remove the template and set it aside. 4. At each of the marks made in Step 3, carefully drill a 1/8 inch (3 mm) diameter pilot hole. 5. Using the pilot holes drilled in Step 4, use a 9/32 inch (7 mm) diameter bit to finish drilling the holes for the trim piece. NOTES Before installing the lid trim, test fit to ensure adequate clearance of both mounting pads through the drilled holes in the saddlebag lid. The trim pieces are side-specific; the front legs are angled to match the lid front. If the pads do not fit loosely in the holes, it may be necessary to slightly enlarge the holes to provide clearance and maintain proper alignment of the trim on the lid. Clean the saddlebag lid inside and out, and the inside of the saddlebag with a soft cloth, making sure to remove any shavings left from drilling. 6. Obtain the correct saddlebag lid trim (1 or 2) and a trim gasket (3) from the kit. Peel the liner from the adhesive backing of the gasket. 7. Position the gasket onto the bottom surface of the trim, making sure the gasket remains inside the outer edges of the trim, and smooth it into place. 8. Obtain a pan head screw (6) from the kit. 9. Using a T25 TORX® drive head, start the screw part way into one of the holes on the underside of the trim, to form a few threads in the hole, then back the screw out of the hole. Repeat for the second hole. 10. Install the trim piece onto the lid, fitting the mounting pads into the holes drilled in Step 5. 11. Place a flat washer (5) from the kit onto the threads of the screw (6), followed by a rubber washer (4). Place two drops of Loctite® 243 (blue) onto the screw threads. 12. While supporting the lid trim in place, open the saddlebag lid and install the washers and screw through the lid into one of the trim mounting pads, finger tight. Repeat for the remaining trim mounting pad, with another screw, flat washer and rubber washer. 13. Apply a small amount of pressure to the trim piece above each screw and continue to tighten both screws to 25-28 in-lbs (2.8-3.2 Nm) . 14. Repeat steps 1 through 13 for the opposite saddlebag lid

HARLEY DAVIDSON SOFTAIL DETACHABLE TWO-UP TOUR-PAK LUGGAGE RACK INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 07-03-2011

download

TOUR-PAK LUGGAGE INSTALLATION TO RACK 1. Open the lid and, if necessary, remove all items from inside the Tour-Pak luggage.  Remove the rubber mat from the luggage floor. 2. If holes ARE NOT pre-drilled in the floor of the luggage,       see Figure 1. To prevent damage to the leather while drilling, place blocks of wood underneath the Tour-Pak luggage at the drilling sites.  Use the four inboard holes (3) in the metal base of the luggage (2) as a guide, and carefully drill four 11/32 inch (9 mm)  holes through the floor of the luggage. 1 2 3 is04249 1. Front of motorcycle 2. Tour-Pak 3. Drill four 11/32 inch (9 mm) diameter holes Figure 1.  Drill Attachment Hole Locations in Tour-Pak NOTE See Figure 3. When installing the luggage to the rack in the following steps, note that holes in the luggage rack (2) provide forward (A) and rearward (B) positions for mounting the lug- gage. 3. Place the luggage on the luggage rack.  Align the holes in the luggage mounting plate with the forward or rearward holes in the rack. 4. ALL applications: Obtain the hex head cap screws (9), lock nuts (11) and plain washers (10) from the kit. Place a washer over the threads of each screw, and insert the screw threads, from the inside, through the Tour-Pak luggage mounting plate and floor, and into the holes in the rack. NOTE Always install the mounting screws from inside the luggage.  If the screws are installed from the bottom, the screw ends can tear the rubber mat and scratch objects, such as helmets, stored inside the luggage. 5. From the underside of the rack, install a washer and lock nut onto the threads of each screw.  In a crosswise pattern, incrementally tighten each screw to 19 ft-lbs (25 Nm) . 6. Install the rubber mat into the luggage.  Close and latch the lid. 7. If not already in place, install the Detachable Docking Hardware Kit to the vehicle per the instructions in that kit

Incoming search terms:

HARLEY DAVIDSON CONTOURED TOUR-PAK LUGGAGE RACK KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 05-04-2011

download
INSTALLATION NOTE The location of the Tour-Pak spoiler has a direct relationship to the location of Tour-Pak mounted luggage rack. The spoiler template will locate the Tour-Pak spoiler in the correct position for the luggage rack so that the spoiler may be added in the future. It is recommended that the spoiler be installed first. See Figure 1. 1. Identify if the installation of a Tour-Pak mounted spoiler is desired in the future. Use the template if the spoiler will be installed. Cut the template along the appropriate line. Carefully place template on top of Tour-Pak lid, aligning edges of template with top surface of Tour-Pak. Tape template in desired location. 1 is 00579 1. Check clearance between rack and spoiler Figure 1. Tour-Pak Rack and Spoiler NOTE Position top rack with upright section toward rear of motorcycle. To avoid contact with the passenger backrest pad, do not mount the top rack in too far forward a position. 2. See Figure 2. Place the four mounting pads (1) onto the four mounting supports on top rack (2). Carefully center the rack on the lid and position the rack rear supports 5/8 inch to 3/4 inch (16 mm to 19 mm) in front of the emblem on the Tour-Pak lid, as shown. 1 is 00636 1.5/8 in. – 3/4 in. (16 mm – 19 mm) Figure 2. Locate Holes From Emblem 3. Use a grease pencil to temporarily mark the positions of the four mounting pads on Tour-Pak cover. NOTE Apply masking tape to the Tour-Pak cover painted surface at the four points where the top rack mounting holes will be drilled. The tape can be marked for hole location, and will help prevent the paint from being chipped during the drilling procedure. 4. Carefully remove top rack/mounting pad assembly. Place a strip of masking tape over each grease pencil mark on the Tour-Pak cover. Once again, position top rack/mounting pad assembly on Tour-Pak cover in the desired mounting location. 5. Using a soft lead pencil on the masking tape strips, trace a circle around each mounting pad. Remove top rack/mounting pad assembly. Use a ruler to mark the exact center of each circle drawn on the tape strips. NOTE Remove all contents from within the Tour-Pak to avoid possible contact with the moving drill bit during the following drilling procedure. 6. Drill starter holes using a 1/16 inch drill bit. Drill the finished holes for the mounting screws using a 9/32 inch drill bit. Remove masking tape strips. 7. Apply a small amount of silicone sealant around each mounting hole on interior surface of Tour-Pak cover

Incoming search terms:

HARLEY DAVIDSON SCREAMIN' EAGLE MECHANICAL COMPRESSION RELEASE FIX- TURE

0

Filed Under (Harley Davidson) by admin on 04-02-2011

download
DRILLING AND TAPPING PROCEDURE Wear safety glasses or goggles while drilling. Flying debris could result in serious eye injury. (00565b) NOTE Perform the following procedure on both the front and rear cylinder heads. Tool Setup NOTE Due to slight manufacturing differences, it may be necessary to tap the fixture into place with a rubber mallet. Do NOT use excessive force. 1. Align the fixture’s locating pins with the 3/8 inch tooling holes in the head and install the fixture on the head. 2. See Figure 1 and Figure 6. Secure the fixture (1) to the head with two 5/16-18 socket head cap screws (2) and washers (9) included in the kit. Install the screws in the holes marked “F” when modifying the front head or in the holes marked “R” when modifying the rear head. Tighten screws to 80 in-lbs (9 Nm) . 3. See Figure 3 and Figure 6. Install the drill bushing (3) in the bore marked “FRONT” when modifying the front head or in the bore marked “REAR” when modifying the rear head. 4. Tighten drill bushing set screw to 50 in-lbs (5.6 Nm) . 5. See Figure 2 and Figure 6. Install collar stop (4) onto the 1/2 inch diameter shank of the step drill bit (5). Secure the collar stop with the set screw 3.900 inches (9.90 cm) from the beginning of the 3/4 inch diameter step of the drill bi

Incoming search terms: