54565 97c shocks on sportster 2015

You search Auto repair manual PDF 54565 97c shocks on sportster 2015, if there are search results will appear below. If search results do not exist, please search by others keyword.



  54565 97c shocks on sportster 2015 Direct Download speed 5282 Kb/s

  54565 97c shocks on sportster 2015 Full Version speed 6162 Kb/s



Ultima Billet Rear Shocks Installation Instruction Sheet

0

Filed Under (Tips and Review) by admin on 30-11-2010

download
Unloading the rear suspension Use a jack under a flat part of the motorcycle and lift until the rear tire is barely resting on the surface. This ensures that the shocks are unloaded. They are now ready for removal. Remove the old shocks Refer to the service manual specific to your motorcycle for this process. Unbolt the old shocks. Save the necessary hardware if you have not purchased new hardware. Installation Shocks should be installed with the preload adjuster on top (see Preload Adjustment). With the new shocks in hand; please go over the hardware configuration diagram (Figure 3) to decide which configuration best fits your application. Spacers are included to provide clearance between the shocks and your motorcycle (Figure 4). Typically start on which ever side the final drive is located. This side normally causes the clearance issues. Each eye and each side should be configured the same way. Make sure to use the proper hardware so that the shock- bushings fit the shock-bolts as snugly as possible. Shocks come with a 1/2″ ID bushing installed. This is needed for all applications. An optional bushing is included and should be used in addition when 3/8″ bolts are used instead of the larger 1/2″bolts. Unless new hardware was purchased, you will use the stock bolts from your old shocks to install the new shocks. Use Red Locktite (or equivalent) and use a torque wrench to tighten as follows: Models that use 1/2″ bolts: 65ft-lbs Models that use 3/8″ bolts: 30ft-lbs (Figures 1 & 2) Be sure to check clearance between the shock and the belt-guard. If there is any contact you will need to alter your spacer arrangement to accommodate this. Check tire to fender clearance as well. This clearance will be reduced when lowering shocks are used. Preload Adjustment Your new Ultima Billet Shocks are preload adjustable. Adjustment should be done once the shocks are installed. To adjust use a strap wrench and turn the top part of the shock (Figure 6) clock-wise to tighten or provide more preload (this stiffens the suspension), or counter-clockwise to loosen or subtract preload (this softens the suspension). Hand adjustments may be sufficient on models with smaller spring rates while the strap wrench will be required on the high spring rate shocks. You will see notches (Figure 6) that appear on the shock as the shock is preloaded. These should help you obtain the same preload for both sides of the motorcycle. Both shocks should be adjusted to the same level of preload.

Incoming search terms:

HARLEY-DAVIDSON SOFTAIL MODELS STEALTH AIR SHOCK MOUNTING

0

Filed Under (Harley Davidson) by admin on 16-12-2010

download
INSTALLATION 1. Remove the seat, inner fender, and ignition coil cover. Removing the rear wheel assembly is recommended for ease of installation, but not absolutely necessary. Remove the nut cup and outer grommet on each of the Works shocks. If you intend to leave the ride height at stock height for road riding, position the inner nut cup SHOC KS SHOC KS WORKS PERFORMANCE PRODUCTS, INC. 21045 Osborne St., Canoga Park, CA 91304 818.701.1010 fax 818.701.9043 STEALTH AIR SHOCK MOUNTING FOR HARLEY-DAVIDSON SOFTAIL MODELS 2000-ON #HDAIR-00 – 02/15/2006 WARNING! THESE SHOCKS MUST ONLY BE USED WITH STOCK SWINGARMS AND ON STOCK FRAMES WITH THE STOCK BOTTOMING BUMPERS ON THE CHASSIS TO LIMIT THE TRAVEL OF THE SHOCKS. AFTERMARKET SWINGARMS, OR MODIFIED SWINGARMS THAT DO NOT HAVE THE UPPER BRACE THAT ACTS AGAINST THE BOTTOMING BUMPERS CANNOT BE USED WITH THESE SHOCKS. INCREASING THE TRAVEL BY ELIMINATING THE BUMP STOPS OR A NON-STANDARD SWINGARM DESIGN WILL ALLOW THE TIRE TO MAKE CONTACT WITH THE FENDER OR OTHER CHASSIS COMPONENTS, AND CAN DAMAGE THE SHOCKS. 19. Lock Washers 20. Long Bolts (2) 21. Short Bolts (2) 13. Din Plug Screw 14. Din Plug Gasket 15. Cap 16. Eye Spacers (4) 17. Cotter Pins (2) 18. Switch Bracket 7. Compressor Bracket 8. Harness 9. Fuse Block 10. Din Connector 11. Solenoid 12. Hose 1. Damper Shock 2. Air Spring Shock 3. Nut Cup 4. Grommet 5. Hose 6. Compressor 1 2 3 4 5 6 7 8 9 10 11 12 13 15 16 17 14 18 19 20 21 Fig. 1–Nomenclature on the damper shock up against the ring nut. The shocks are now ready to install. 2. Place the motorcycle on a suitable frame stand allowing unrestricted access to the shocks. 3. Place a small screw jack under the swing arm to support the weight as well as allow you to position the swing arm correctly to line up the shock mounting bolts. Remove stock shocks. 4. Install the left side (damping) shock with the stock mounting bolt. Make sure that the bolt threads and threaded portions of the frame are free of oil and grease. Grease the shoulders of the bolts and use thread lock compounds on the threads. Discard the stock shock washers on both shocks. Do not use any washers- -including the stock washers on these bolts. Use only the spacers included. The 3/16-inch wide spacers are used on each side of the shock eye. Do not “double-up” the spacers together on either side of the shock eye, as this will cause misalignment of the shocks which can lead to premature wear or damage to the shocks. 5. Put the supplied spacers on each side of the eye. The shoulder of the bolt must protrude a small amount through the shock eyes in order to allow the shock to pivot freely. This is extremely important. With the shocks fully tightened, the spacers should be free to rotate with finger pressure. If the washer is used or a non-stock bolt is used, the bolts will work loose or break because the shocks are in a bind.

440 Series Shocks Installation Manual

0

Filed Under (Tips and Review) by admin on 14-12-2010

download
Follow instructions in an authorized shop manual or take the motorcycle toacompetent dealer. The motorcycle must be on thecenterstand (if equipped) or securely blocked to prevent it from tipping over when the shocks are removed. Failure to do so can cause serious damage and/or injury. The use of any lowering blocks is not recommended and will void the warranty. Make sure that proper bushings/sleeves are installed in the shocks. Improper bushings/sleeves can cause unsatisfactory and/or unsafe operation (seethe instructions packaged with the mounting hardware). 1. Place a quality jack or sufficient blocks under the motorcycle to securely lift the rear wheel slightly off the ground. 2. Using the correct shop manual, remove the old shocks and note location of the mounting hardware. If additional accessories are installed on your motorcycle, please refer to their mounting instruc- tionsforremoval to gain access to your shocks. 3. Before installing your new Progressive shocks you need to check the tire to fender clearance, (see Ain figure1) making sure that the tire does not come in contact with the fender. If the rear fender or tire has been changed to anything other than stock, a travel limiter maybe required. On some models with side bags or luggage, removal of the lower cover maybe required to eliminate any interference. Install shock assemblies onto the motorcycle (shaft end must be down!) and tighten bolts/nuts to proper torque. Check the clearances of the shock to frame (B) and shock to chain, chain guide, disc caliper and linkage (C) in figure 1. The lower cover can be removed for clearance if necessary. 4. Reinstall any accesso- riesremovedin accord with their mounting instructions. Make sure accessories do not in- terferewith shocks throughout full travel. If any accessories bolt to shock mounting points, a careful inspection must be made to insure that they do not bind the shocks in anyway (see figure 2)

WORKS PERFORMANCE STREET TRACKER SHOCKS FOR BIG DOG MOTORCYCLES

0

Filed Under (Tips and Review) by admin on 17-12-2010

download
SHOCK REMOVAL AND INSTALLATION– The shocks are fitted with special length spacers to maintain correct alignment between the frame and the swingarm. If the shocks are removed for service or repair, they must be installed in the correct position. Refer to the diagram on the next page for spacer positioning and layout. NOTE: Misalignment between the mounts on the frame and the mounts on the swingarm can cause binding between the shock shaft and shaft bushing. Misalignment of more than 1/4 inch can cause the shocks to bind up and not function properly. If this binding occurs, the shocks will feel overly stiff and harsh. Follow the procedures below to check for misalignment when installing the shocks. NOTE: The shock bushings are designed to have a certain side-to-side “float” to keep them from binding. As a result, do not grind or file the inner or outer edges of the bushings to make them narrower. The amount of “float” in the bushing set is necessary to ensure smooth operation of the damper assembly. If the shock eyes are tightened metal-to-metal (the outer faces of the eyes to the flanges or washers), this will lead to a harsh, stiff or choppy ride and premature seal leakage or damage to the shafts. MULTI-RATE SPRINGS Depending on each application, single or dual-rate springs are available. Dual-rate springs are just that– a spring set with two separate rates. This is done with a short spring stacked on a longer spring. As both springs compress they produce a soft, or initial, rate. The spring set will maintain this initial rate until the short spring stops compressing. At that point, the spring rate “crosses over” to the stiffer, or final, rate. This multi-rate system allows a soft initial rate for comfort on small bumps, but has the capability of soaking up the big pot-holes and other road hazards. PRELOAD ADJUSTMENT— On Works shocks, threaded preload is standard. (See Fig. 2.) This allows the adjustment of the ride height of the motorcycle. The preload is changed by turning a threaded nut down towards the spring (higher ride height) or up away from the spring (lower ride height). The nut is a right-hand thread. It is used primarily to set the ride height for solo riding, but can also be used when

Incoming search terms:

Harley Davidson Softails Shocks Installation download

0

Filed Under (Harley Davidson) by admin on 28-02-2012

download
Progressive Suspension shocks for your Softail are designed as a direct bolt on replacement for your stockers. Although they are very similar in appearance, they have vastly improved damping and spring rates. Our shocks do not use the remote reservoir system used on earlier model Softail models. 1. Place motorcycle securely on stand or blocks so the rear wheel is slightly off the ground. 2. Per instructions in a authorized shop manual, remove your old shocks. Note location of the mounting hardware. 3. Install the Progressive Suspension shocks using the stock mounting bolts and washers. 4. Tighten all shock mounting bolts to the proper torque specifications (see shop manual for specs) 5. Progressive Suspension shocks have adjustable pre-load to compensate for varying weights. The included wrench or a Harley Davidson pre-load adjustment wrench is necessary to adjust the pre-load setting. Replacement Progressive Suspension, Inc. wrenches are available as Part # SW-784 from most Dealers and Accessory Stores and the Harley Davidson wrench is available as part #94455-89 from any Harley Davidson Dealer. Spring preload is set by us to the lightest setting. To increase preload for heavier riders/loads/passengers, loosen locknut with the inside portion of the supplied wrench or a 1 1/ 16 ” wrench and back it off several turns. Use the supplied wrench or a Harley adjustment wrench to turn the adjustment nut counterclockwise to the desired preload setting. Then tighten the 11/ 16 ” lock nut. Both shocks must be adjusted to the same, equal setting

Incoming search terms:

HARLEY DAVIDSON DYNA AND SPORTSTER Chrome Front Wheel Spacers INSTALLATION ISNTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 29-01-2011

download
1. Block motorcycle underneath frame so front wheel is raised off the ground. 2. See Figure 1. Remove the upper (1) and lower (2) brake caliper mounting bolts and brake caliper(s) (3). Support caliper(s) using a rubber bungee cord. Be careful not to scratch fender paint. NOTES Do not operate front brake lever with the front wheel removed or the caliper piston may be forced out of piston bores. Reseating the piston requires disassembly of the caliper. Prior to removal, make note of existing left and right spacer location. The new spacers will be installed in the locations. 3. See Figure 3. On left side of wheel, remove axle nut (D), lockwasher (E) and washer (F). Perform the following: 4. Sportster and Dyna (except FXDWG) See Figure 2. Loosen the pinch bolt nut (1) and pull the the axle (2) free. Remove wheel and spacers. Leave bearing(s) in place. Discard spacers. 3 1 2 is04469 1. Brake caliper mounting bolt, long (top) 2. Brake caliper mounting bolt, short (bottom) 3. Brake caliper Figure 1. Caliper Mounting Bolts (Left Side) Dyna and Sportster 3 1 2 is04470 1. Pinch bolt nut 2. Axle 3. Pinch bolt Figure 2. Front Wheel Mounting (Dyna and Sportster Except FXDWG-Right Side) 5. See Figure 3. Obtain the new right (1) and left (2) chrome spacers from kit and install. 6. Apply a light coat of ANTI-SEIZE LUBRICANT (Harley- Davidson Part Number 98960-97) to the axle.
7. Place wheel between sliders and install axle. Verify that axle spacers on right and left side are properly installed. 8. See Figure 3. Install the washer (F), lockwasher (E) and nut (D) onto threaded end of axle (A). 9. In order to properly align the front fork, perform the fol- lowing: a. On the right side of the wheel, insert a 7/16 inch drill bit through the hole in the axle. While holding axle stationary, tighten axle nut to 50-55 ft-lbs (61.0-74.6 Nm) . b. Pull fork leg so that it just contacts drill bit. Tighten according to the following: c. Refer to Figure 2. Tighten the Axle Pinch Bolt Nut to 25-30 ft-lbs (33.9-40.7 Nm) . d. Remove drill bit from axle hole. 10. Follow instructions in Service Manual and install brake caliper to the sliders noting the following: •Loosely install long bolt to the top hole on fork leg. Install the short mounting bolt to the bottom hole and tighten to 28-38 ft-lb (38.0-51.5 Nm) . •Final tighten top bolt to 28-38 ft-lbs (38.0-51.5 Nm) . 11. Repeat Step 10 to install brake caliper on opposite side of wheel. After servicing brakes and before moving motorcycle, pump brakes to build brake system pressure. Insufficient pressure can adversely affect brake performance, which could result in death or serious injury. (00279a) 12. Pump brake lever to move pistons out until they contact both brake pads. Verify piston location against pads

Incoming search terms:

HARLEY DAVIDSON HARDWARE/ TURN SIGNAL RELOCATION KIT FOR SPORTSTER LEATHER SADDLEBAG KITS INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 17-03-2011

download
Installation Instructions for 79052-04 and 79073-04 Do not exceed 7 lbs (3.17 kg) maximum load in each saddlebag. Additional weight can affect a motorcycle’s stability, handling characteristics, and safe operating speed which may lead to an accident resulting in death or serious injury. NOTE A pick tool (Snap-on TT600-3) will be required for 1996 and later models for removing and reinstalling a multi-lock amp con- nector. NOTE A Service Manual for your vehicle is available from your Harley- Davidson Dealer. Installation – Hugger Models Only (1994-1997) To perform the following steps for Hugger Models only, fender and frame must be sufficiently supported, as both shocks will need to be removed at the same time. An improperly supported vehicle could result in death or serious injury. A Service Manual is needed to install this kit. The rider’s safety depends upon the correct installation of this kit. If the procedure is not within your capabilities or you do not have the correct tools, have your Harley-Davidson Dealer perform the installation. Improper installation of this kit could result in death or serious injury. To prevent accidental vehicle start-up, which could cause death or serious injury, disconnect battery cables (negative cable first) before proceeding. Disconnect negative (-) battery cable first. If positive (+) cable should contact ground with negative (-) cable connected, the resulting sparks can cause a battery explosion, which could result in death or serious injury. (00049a) 1. Remove seat, sissy bar and sideplate, if applicable. Retain hardware for reinstallation. Disconnect battery, negative cable first. 2. Properly support motorcycle under frame to prepare for removal of right and left shocks. 3. Remove rear buttonhead screw on each side of fender. 4. See Figure 1. With rear fender and frame securely supported, remove left and right shocks by removing upper nut (2), washer(s) (3) and shock cover (4). Remove bolt (6), washer (7) and locknut (8) at lower shock mount. Remove shock

2000 & later Harley Davidson Softails Drag Specialties Shocks Installation Manual

0

Filed Under (Harley Davidson) by admin on 31-03-2012

download
1. Place motorcycle securely on stand or blocks so the rear wheel is slightly off the ground. 2. Per instructions in a authorized shop manual, remove your old shocks. Note location of the mounting hard- ware. 3. Before reinstalling a Drag Specialties adjustable ride height shock, spin the non-flanged nut all the way onto the stud mount, followed by a bushing-cup, bushing, and sleeve. Then install shocks as you would a stock unit, following an authorized shop manual. With the non-flanged nut spun all the way onto the stud, the stock ride height is achieved. Once you have installed the other bushing, bushing-cup, and flanged nut you can now install the safety E-clip. This E-clip is snapped into the groove near the end of the stud mount where the threads stop. This is to serve as a reference point ONLY – when the flanged-nut reaches it you have lowered your ride height the maximum 2 inches. DO NOT torque the flange-nut against the E- clip (see figure 1). 4. Tighten all shock mounting bolts to the proper torque specifications (see shop manual for specs). 5. Drag Specialties shocks have adjustable pre-load to compensate for varying weights. A Harley Davidson pre-load adjustment wrench is necessary to adjust the pre-load setting. Progressive Suspension, Inc. wrenches are available as Part # SW-784 from most Dealers and Accessory Stores and the Harley Davidson wrench is available as part #94455-89 from any Harley Davidson Dealer. Spring preload is set by us to the lightest setting. To increase preload for heavier riders/loads/passengers, loosen locknut with the inside portion of the supplied wrench or a 1 1/ 16 ” wrench and back it off several turns. Use the supplied wrench or a Harley

Harley Davidson Sportster 4 Piston Rear Brake Caliper installation Manual

0

Filed Under (Harley Davidson) by admin on 02-04-2012

download
Installing Rear Caliper – Sportster Models Removing The Stock Brakes SPORTSTER REAR BRAKE SYSTEM 84 & UP MODELS The basic steps are the same to install a PM rear brake caliper kit on any of the late model Harley Davidson “swingarm” style motorcycles; all require the removal of the rear wheel. Using a suitable lift, raise the motorcycle high enough off the ground to allow you to remove the rear wheel assembly. PHOTO 2 W a r n i n g Center the motorcycle on the lift so that it will not fall while you are working on it. Photo 2: Remove the rear brake caliper assembly by unscrewing the 2 caliper mounting bolts that go through the caliper into the caliper mounting bracket. Lift the caliper up and off the mounting bracket and brake rotor, move the caliper back out of your working area. Don’t remove the brake line from the caliper yet; you will do this just before you are ready to hook it up to the new caliper. The brake pads are held into the caliper mounting bracket by 2 spring clips; slide the brake pads out of the mounting bracket and remove the retaining springs. PHOTO 3 Remove Cotter pin and rear axle nut, slide rear axle completely out. Photo 3: Remove nut from Right rear shock and rotate belt guard up. Slide belt off of pulley and roll rear wheel back 6 – 8″. Photo 4: Remove original caliper bracket from swingarm

HARLEY DAVIDSON SPORTSTER LOW REAR SUSPENSION KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 13-02-2011

download
INSTALLATION NOTE Internal shock absorber components are not repairable beyond the Service Parts listed on this instruction sheet. Consult your Harley-Davidson dealer if further service is required. The installation procedures for this kit are the same as the original equipment (OE) installation procedures in the Service Manual. Refer to the appropriate Service Manual for the rear suspension system removal and installation procedures. The OE hardware will be re-used in the kit installation. Installation of any accessory suspension components can affect cornering clearance. This could distract the rider, causing loss of control and death or serious injury. (00431b) SHOCK PRELOAD (SPRING) ADJUSTMENT Refer to the appropriate Service Manual for spring adjustment. Spanner wrench (94700-52L) is required for spring adjustment. SERVICE PARTS 1 is04854 Figure 1. Service Parts: Sportster Low Rear Suspension Kit Table 1. Service Parts: Sportster Low Rear Suspension Kit Part Number Description (Quantity) Item 54734-04 Rear shock (2)

Incoming search terms: