68913 98b wire harness

You search Auto repair manual PDF 68913 98b wire harness, if there are search results will appear below. If search results do not exist, please search by others keyword.



  68913 98b wire harness Direct Download speed 5282 Kb/s

  68913 98b wire harness Full Version speed 6162 Kb/s



2002-2005 Honda VFR800/A Wire Harness Replacement Manual

0

Filed Under (Honda) by admin on 21-04-2011

download
If the 18P (light blue) connector is in abnormal condition as shown below, contact TechLine at (800) 421-1900, option 9. FRONT SUB-HARNESS REPLACEMENT 1. Remove the front sub-harness from the cowl stay hooks. Disconnect all the electrical components from the front sub-harness. 2. Temporarily set the main wire harness aside, and disconnect the 6P (natural) con- nector. Then, carefully remove the front sub-harness. 3. Install the new front sub-harness by con- necting the 14P (natural) and 18P (light blue) connectors. NOTE: For routing specifications, refer to the WIRING & HARNESS ROUTING SECTION on pages 7-8. 4. Attach the front sub-harness on the cowl stay hooks. Make sure the front sub-harness is routed elow the main sub-harness. ABNORMAL CONDITION STAY HOOKS 6P (NATURAL) CONNECTOR FRONT UB-HARNESS 14P (NATURAL) CONNECTOR 18P (LIGHT BLUE) CONNECTOR FRONT SUB-HARNESSSTAY HOOK Page 4 VFR800/A #4 4 of 12 NOVEMBER 2007 5. Place the front sub-harness between the radiator and the frame, and below the rec- tifier. Be careful not to damage the front sub-harness or other components. 6. Re-connect the front sub-harness to the 6P (natural) connector. 7. Secure the main wire harness and the front sub-harness using the longer wire band. 8. Secure the main wire harness and the upper side of the front sub-harness using the shorter wire band. Adjust the wire har- ness located within the frame and the radi- ator hose accordingly. 9. Secure the main wire harness fuse box to the front sub-harness using the shorter wire band. FRONT SUB-HARNESS STAY HOOK MAIN-HARNESS FRONT SUB-HARNESS FRONT SUB-HARNESS 6P CONNECTOR (Male) 6P CONNECTOR (Female) WIRE BAND (LONG) WIRE BAND (SHORT)
WIRE BAND (LONG) WIRE BAND (SHORT) MAIN WIRE HARNESS FUSE BO

Incoming search terms:

TOYOTA COROLLA 1984-2006 VEHICLE WIRING VEHICLE WIRING REMOVAL

0

Filed Under (Toyota Manuals) by admin on 04-10-2011

download
IRING INFORMATION: 1984 Toyota Corolla FWD WIRE WIRE COLOR WIRE LOCATION 12V CONSTANT WIRE WHITE OR WHITE/RED Ignition Harness STARTER WIRE BLACK/WHITE Ignition Harness IGNITION WIRE BLACK/YELLOW Ignition Harness SECOND IGNITION WIRE BLACK/ORANGE Ignition Harness ACCESSORY WIRE BLUE/RED Ignition Harness POWER DOOR LOCK (-) BLUE/WHITE Harness In Driver’s Kick Panel POWER DOOR UNLOCK (-) BLUE/RED Harness In Driver’s Kick Panel PARKING LIGHTS (+) DK. GREEN Harness In Driver’s Kick Panel PARKING LIGHTS (-) LT. GREEN Harness At Steering Column HEADLIGHTS (-) RED/WHITE Harness At Steering Column DOOR TRIGGER (-) RED/WHT OR BLK/WHT Harness At Fuse Box TRUNK TRIGGER COMMON WITH DOORS (Hatchback Only) TACHOMETER WIRE BLACK At Ignition Coil BRAKE WIRE (+) GREEN/WHITE Brake Pedal Switch HORN TRIGGER (-) GREEN/RED Steering Column LEFT FRONT WINDOW UP GREEN/BLACK At Driver Window Motor Inside Door LEFT FRONT WINDOW DOWN BLUE/RED At Driver Window Motor Inside Door RIGHT FRONT WINDOW UP GREEN Harness In Driver’s Kick From Driver Door RIGHT FRONT WINDOW DOWN BLUE/WHITE Harness In Driver’s Kick From Driver Door LEFT REAR WINDOW UP RED/BLACK Harness In Driver’s Kick From Driver Door LEFT REAR WINDOW DOWN RED/YELLOW Harness In Driver’s Kick From Driver Door RIGHT REAR WINDOW UP RED/BLUE Harness In Driver’s Kick From Driver Door RIGHT REAR WINDOW DOWN BLUE/BLACK Harness In Driver’s Kick From Driver Doo

Incoming search terms:

1982-2005 Harley Motorcycle Removal and Installation Instructions

0

Filed Under (Harley Davidson) by admin on 31-03-2012

download
” bolt from the mounting stem on the Signal® mirror. While seated on the motorcycle, position the Signal® mirror on the handle bar. Secure the Signal® mirror to the handle bar using the 5/ 16 ” bolt. Make sure the bolt is tight! Guide the Signal® mirror wire harness into the cowling by going along side the existing factory wire harness. 4 Remove any slack in the wire harness. Secure the wire harness to the handle bar using a supplied tie wrap. 5 6 Adjust the position of the Signal® mirror and tighten the ball retention screws. Remove the motorcycle seat. Remove the aft mounting bolts on the fuel tank. 7 Guide the Signal® mirror wire harness along the inside of the fuel tank’s front mounting bolt and between the crossover tube. 8 9 Lift up the aft portion of the fuel tank and guide the Signal® mirror wire harness down the backbone of the motorcycle frame, alongside the existing factory wire harness. The motorcycle’s electrical wiring for turn indicators is located aft of the gas tank on the backbone of the frame. Guide the new wire harness from the Signal® mirror to the electrical wiring. Cut off any excess slack in the wire. Locate the SOLID BROWN wire from the wire connector. Turn the ignition key so that electrical power is on and activate the right side turn indicator. Probe the wire with the wire tester to verify that flashing turn indicator power is present. Label that wire as ‘right side turn’. Repeat all of the previous steps to replace the left side factory mirror with the new Signal® mirror. Locate the SOLID VIOLET wire from the wire connector. Activate the left side turn indicator and probe the wire with the wire tester to verify that flashing turn indicator power is present. Label that wire as ‘left side turn

Incoming search terms:

HONDA GL-1500 Trailer Wire Harness with Relay INSTALLATION MANUAL

0

Filed Under (Honda) by admin on 27-02-2011

download
Seat: (if optional accessory wire is to be used) After removing trunk pan, run a stiff piece of wire from the bottom of the left saddlebag frame behind the rear tire up until it comes out under the trunk. Then hook open end of wire harness to fish wire and tape with electrical tape. Pull the harness back down to the bottom of the saddlebag frame. Route the long part of harness wire around the back of the license plate light to the right side 6-pin vertical connector just in front of tail light assembly. Unplug the stock connector and plug wire harness in between the stock plugs. Do the same for the left side with the short side of the Y on the harness. Now pull the slack down from the bottom of the harness and tuck all of the wires under the frames tubes so that the pan can be reinstalled without any problems. You can now hook up the loose ends of the harness to any style connector to match your trailer connector using the following color codes: GREEN GROUND ORANGE- LEFT TURN YELLOW- BRAKE BLUE- RIGHT TURN BROWN- TAIL RED POWER . Note : This accessory is an electronic isolated trailer wire harness. It should be installed by a qualified mechanic . 1. Disconnect the negative from the battery. 2. Install the harness. 3. When connecting to the trailer make sure all wires are used for the proper use and are waterproof. Make sure there are not exposed wires. Consult the trailer manufacturer for proper wiring. 4. Reconnect the battery negative. Double check the functions

HARLEY DAVIDSON VRSC BRACKET FOR BILLET HEADLAMP SHELL REMOVAL AND INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 31-01-2011

download
REMOVAL VRSCA Models 1. Remove windshield (if equipped). Refer to appropriate Instruction Sheet for procedures. 2. Remove right side cover and maxi-fuse. Refer to MAXI- FUSE in Service Manual. 3. See Figure 1. Disconnect headlamp connector (1) from vehicle wire harness. 4. Remove two screws (2), headlamp mounting bracket (3), and headlamp assembly (4) from upper bracket. 2 3 4 5 1 is03046 1. Connector 2. Screw (2) 3. Bracket 4. Headlamp assembly 5. Screw (2) Figure 1. VRSCA Headlamp Assembly VRSCB Models 1. Remove windshield (if equipped). Refer to appropriate Instruction Sheet for procedures. 2. Remove right side cover and maxi-fuse. Refer to MAXI- FUSE in Service Manual. 3. See Figure 2. Disconnect headlamp connector (1) from vehicle wire harness. 4. Remove two screws (2), headlamp assembly (3), and headlamp mounting bracket (4) from upper bracket. 5. Remove nut (5), screw (6), and trim ring (7) from head- lamp. 6. Remove lens assembly (8) from headlamp shell (9). Save lens assembly for Billet Headlamp Shell Kit 67704-03 installation INSTALLATION 2004-Earlier VRSCA and VRSCB Models 1. Assemble Chrome Billet Headlamp Shell Kit (67704-03). Refer to Instruction Sheet-J03018. NOTES VRSCA models use Headlamp 68297-05, while VRSCB models use original equipment lens assembly (including gasket and boot). Adapter ring from kit (Figure 6, Item 1) will be used to install billet headlamp assembly on Instruction Sheet-J03018. 2. See Figure 3. Cut the two connectors (1) from existing headlamp wire harness (2). Be sure to cut the wires as close to the back of the connector as possible. 3. See Figure 6. Route new wire harness (2) through the hole in bottom of the billet headlamp shell (A). NOTE Only one 16 AWG wire will fit into pin terminals included in kit. Both black wires (ground) can be joined together, then connected to a single wire, if desired. 4. Tape end of one black wire with electrical tape and secure it to wire harness. 5. See Figure 3 and Figure 6. Install terminal pin (3) and socket housing (4) onto new wire harness (Figure 6, Item 2). Refer to MULTILOCK ELECTRICAL CONNECTORS in Service Manual for installing socket/pin terminals. 3 4 1 2 is03025 1. Connector (2) 2. Wire harness 3. Terminal pin (4) 4. Socket housing Figure 3. 2004-Earlier VRSCA and VRSCB Headlamp Wire Harness 2005-Later VRSCA and VRSCB Models 1. Assemble Chrome Billet Headlamp Shell Kit (67704-03). Refer to Instruction Sheet-J03018. NOTES VRSCA models use Headlamp 68297-05, while VRSCB models use original equipment lens assembly (including gasket and boot). Adapter ring from kit (Figure 6, Item 1) will be used to install billet headlamp assembly on Instruction Sheet-J03018. 2. Disconnect and discard existing wire harness. 3. See Figure 6. Connect new wire harness (2) to billet headlamp shell (A). 4. Route wire harness (2) through hole in bottom of billet headlamp shell (A) before installing socket housing (4) provided in kit

SR-C400 Motorcycle Security System INSTALLATION MANUAL AND USER'S GUIDE

0

Filed Under (Tips and Review) by admin on 29-01-2011

download
Routing the Antenna Wire The MCM includes an 18″ antenna wire. The first 12″ is a coaxial wire; the remaining 6″ is the reception antenna wire. When routing, try to avoid running the antenna along or near metal. For best performance, have the antenna wire as vertical as possible and exposed. Wire Connections The system includes one harness (HAR-1a) that connects directly into the MCM. The harness is split into three plugs: one for the GEN-1a connector, one for the optional SN-5 connector and one for the data output for future expansion. Note: Each plug is unique and will only fit the appropriate component one way. Main Harness Note: If the optional factory connector kit is being used, please disregard this section of the instructions and refer to the instructions supplied with the factory connector kit. The main harness consists of two harnesses. One is labeled (HAR-1a) and the second is labeled (GEN-1a). Plug in the white 4 pin connector from the (HAR-1a) into the matching 4 pin connector from the (GEN-1a). The (HAR-1a) also has a waterproof connector that plugs into the MCM. The wires should be connected as follows: HAR-1a Black wire with fuse and ring terminal – To battery Positive (+). GEN-1a Black wire – To ground (-). Orange wire – To tail light wire or any other wire that is hot (+) when ignition is ON (NOTE: this is an input to the alarm this connection is not designed to flash the tail light). Color Codes: Ground (-) Tail Light Honda Green wire Brown wire Kawasaki Black wire Red wire Suzuki Black/White Brown wire Yamaha Black wire Blue wire Harley Davidson Black wire Blue wire

Incoming search terms:

HARLEY DAVIDSON ENGINE GUARD-MOUNTED FOG LAMP KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 19-02-2011

download
VRSC models: See Figure 3. Place the wire harness from the kit into the area in front of the battery. Do not block the air intake opening. All models except VRSC and 2004 and later XL models: See Figure 4. Install the wire harness from the kit. Place the relay in the opening of the frame under the seat area, and route the long leg of the harness forward along the frame backbone. 2004 and later XL models: See Figure 5. Remove the nuts retaining the ignition module (1) and temporarily reposition the module as shown. Place the relay in the recessed area (2) of the oil reservoir. Install the ignition module. Route the long leg of the harness along the frame backbone. CAUTION 1 WARNING -J02798 Figure 3. Install Fog Lamp Wiring Harness (VRSC Models) Place harness into this area but do not block air intake Air intake i04372 Battery Figure 4. Install Fog Lamp Wiring Harness (All Models Except VRSC. Dyna Model Shown) i02286.eps 1. Relay 2. Ground stud 3. Long leg of harness 2 1 3 2 of 6 Figure 2. Fog Lamp Wiring Harness Figure 1. Fog Lamp Schematic Ground To low beam To main circuit breaker Fuse N.O. Contact Switch Coil Fog lamp Fog lamp i01360a Relay 1. Fuse block 2. Relay 3. Connector to power 4. Ring terminals (Ground) 5. To fog lamps 6. Unterminated wire to low beam 7. Switch with boot and bracket 4 2 5 6 7 1 3 i05708 5. All 2003 and earlier models and VRSC: Cut the connector from the white power lead, and replace it with the ring terminal supplied in the kit. 6. All 2003 and earlier models, except VRSC: Connect the white wire with the ring terminal to the copper stud (BAT) terminal of the main circuit breaker. All 2004 and later models, except VRSC: Connect the white wire with connector to the B+ connector on the harness. All VRSC: Connect the white power lead to the battery positive terminal. 7. See Service Part illustration. Connect the black ground wires with the two ring terminals to the ground stud under the seat, or at any good electrical ground point. Secure the kit harness to the adjacent harnesses with cable straps (item 6) from the kit. When routing wires through the front fork, make sure the wires are clear of moving parts, to avoid pinching and possible short circuits. 8. Route the forward end of the harness past the steering head, and route the lamp switch leg of the harness along the left side of the handlebar to the clutch control. 9. See the Service Parts illustration. Obtain the switch mounting bracket (item 11) from the kit. Unscrew the boot from the lamp switch, and install the switch into the bracket. Replace the boot on the switch. NOTE If the boot becomes worn or damaged, or is lost, replace the boot to prevent moisture from entering the switch. See the Service Parts illustration (Item 12). 10. See Figure 6. Remove the lower screw (1) and washer from the clutch control clamp (3), and install the lamp switch and bracket assembly (2). Install the screw and washer and tighten to 60-80 in-lbs (7-9 Nm). 11. See the Service Parts illustration. Secure the lamp switch leg of the harness to the handlebar using the wire harness retainers already on the bike. Snap the retainers into the holes in the handlebar. 12. Remove the headlamp assembly. See HEADLAMP – REMOVAL instructions for the correct model in the Service Manual. CAUTION 3 of 6 -J02798 Figure 6. Install the Lamp Switch on the Clutch Control Clamp i04370 3 1 1. Lower clamp screw 2. Lamp switch and bracket assembly 3. Clutch control clamp 2 Figure 5. Install the Wiring Harness (2004 and Later Models) i05712 3

HONDA Ground Effects Installation Instructions

0

Filed Under (Honda) by admin on 10-11-2010

download
Wiring Installation: 1. Remove the four M8x1.25 socket head cap screws from the seat and remove the passenger handles and seat. 2. Remove both rear side covers, and right front side cover. 3. Remove the two M3 Phillips head screws and two trim clips from the right front storage pocket. 4. Place the three relays of the Ground Effects Ground Effects Ground Effects Ground Effects wiring harness underneath the relay box. 2001 2001 2001 2001 — – 2005 MODELS 2005 MODELS 2005 MODELS 2005 MODELS Route the long end of harness (blue wire and orange wire), behind the fuel tank to the brake lines. The shorter section of the harness will end at the brake lines. Continue along the brake lines to the main harness of the motorcycle to the shelter, then up through the shelter to the pocket area. 5. Locate the harness connectors under the pocket. Go to step 6. 2006 & NEWER MODELS 2006 & NEWER MODELS 2006 & NEWER MODELS 2006 & NEWER MODELS Route the long end of harness (blue wire and orange wire), under the relay box and connect to the Positions Relay. 6. Connect the orange wire to the orange wire with white tracer using a scotch-lok connector. Connect the blue wire to the light blue wire with white tracer using a scotch-lok connector. 7. Route the red and white wires behind the fuel tank, along the left side wiring harness to the fuse box. 8. Connect the RED wire with eyelet connector attached, to the positive side of the accessory terminal in the fuse box. 9. Connect the WHITE wire to the negative battery terminal. 10. Connect the brown wire with white tracer to the brown wire with white tracer (tail relay in relay box) using a scotch-lok connector. 11. Route the orange wire with black tracer and the white wire behind the fuel tank, with at least 6 inches of wire left hanging below the bike. 12. Reinstall the right fairing pocket with the two M3 Phillips head screws and two trim clips. 13. Replace the right front side cover and the right and left rear side covers. 14. Replace the seat and passenger grip handles with the four M8 x 1.25 socket head cap screws

Incoming search terms:

Harley-Davidson Road King Handlebar Removal and Installation Manual

0

Filed Under (Harley Davidson) by admin on 18-03-2012

download
If the wire length appears to be too short, you will have to lengthen the wires. If that’s the case, I must stress that soldering your wires is far superior to using butt splices. Wiring can be pulled from the splices and the splices themselves will take up a lot of room, making your harness bulky. To extend your wires, ensure the wire segments you are going to splice into the harness are of the same gauge as the original harness. Also, it’s a good idea to cut all of the wire segments now, ahead of time, to the same measured length. This will ensure that once all of the new wire Figure 4. Handlebar harness plug wires as they appear from the back of the plug (where the wires enter the plug from the harness) segments are spliced in, all of the finished wires are of the same length and the pins are lined up. Work from wire to wire, cutting them by staggering the cuts about an inch or so apart (see figure 5). This will prevent a bulge in your harness where all the soldering connections are. After cutting each wire, slide on a two-inch piece of heat shrink tubing before starting your soldering. Remove about ¾” of insulation from the ends of the two wire ends (one wire end being the harness, the other being the segment of new wire being spliced in). Halfway down the length of its exposed section, bend each wire 90 degrees and hook the two wire segments together at the bends. Holding the wires securely with a pair of pliers, twist them in opposite directions around each other. Make sure the ends of the wires are wrapped as tight as possible so their sharp points will not cut through the heat shrink tubing when it’s applied. Apply some soldering flux (a little is all you need) and solder the connection by first applying your soldering iron (or gun) to the wire and then applying the solder to the wire. You should not apply the solder directly to the iron as overheating the solder can lead to poorly made solder joints and improper conduction of electricity. When the connection has cooled, slide your heat shrink tubing over the joint and heat it so that the tubing shrinks, making a nice tight seal.

HI-4 DUAL FIRE MOTORCYCLE IGNITION INSTALLATION INSTRUCTIONS

0

Filed Under (Yamaha) by admin on 09-11-2010

download
Turn ignition switch off and disconnect battery ground cable. 2. Refer to Figure 3. Remove OE ignition module and wire harness (items 1-4). You will disconnect two wires at the coil (15), a wire going to the VOES (Vacuum Operated Electrical Switch) (18), a black ground wire at the ignition module, and the 3 pin plug (20) that connects to the sensor plate (11). Refer to shop manual for locations. 3. Remove ignition cover plates and gasket (items 5- 9). This will require drilling out two rivets. The rivets will later be replaced with two supplied self- threading screws. 4. In order to remove the sensor plate cable, the cable plug (20) must be removed first. Use needle nose pliers to pull the terminals out of the plug. Then pull the cable through the exit hole at the bottom of the timing cover. 5. Note location of sensor plate (11). There is a V notch in the sensor plate used for alignment. When you install the HI-4, you should align the V notch in the same location. This should set the timing close enough to start the engine. Remove and save the two standoffs and washers (10). Remove the sensor plate (11). HI-4 INSTALLATION Refer to Figure 4. The HI-4 requires use of the OE timing rotor P/N 32402-83 (used only on 1985 and newer models). If you have an older model or are not sure, check the rotor (9) for the correct part number. For models prior to 1980, use the supplied 10-32 x ¾”bolt and washer to mount the rotor. 1. Install the HI-4 system in place of the OE breaker or sensor plate. Rotate the HI-4 about 90 degrees to give better access to the cable exit hole. Install the HI-4 first, then push the cable through the hole. On some early models it may be necessary to enlarge the wire harness exit hole in the gear cover. Align the V notch on the HI-4 same as the OE plate you removed. Use the OE standoffs to secure the HI-4. You must use lockwashers under the standoffs for proper clearance between the HI-4 and cover plate. Do not fully tighten the standoffs until the timing has been set. 2. Route the HI-4 wire harness along the frame rails up to the coil. Make sure that harness will not be chafed or burned by exhaust heat. Secure harness with tie wraps. Do not install timing cover. HI-4 HOOKUP Crimp terminals and hardware are supplied for your convenience. Use the ring terminals for coil hookup. Use male-female quick disconnects for connections to the tach and vacuum switch (VOES). Tape up any unused wires. 1. Circuit Breaker Cover Screws (2) 2. Circuit Breaker Cover 3. Circuit Breaker Cover Gasket 4. Breaker Plate Screws (2) 5. Breaker Plate Screw Lockwashers & Washers (2 each) 6. Retainer (1971 to early 1972) 7. Circuit Breaker Cam Bolt 8. Breaker Plate Assembly 9. Breaker Cam 10. Advance Assembly 11. Gear Case Cover 11 10 9 8 7 6 5 4 3 2 1 NOTE: Damage will result if the brown tach wire comes in contact with +12V. Figure 1. Harley-Davidson®OE Points System
9000-4002A REV A 3 2/05 1. Identify switched +12 volt wire and tach wire (if equipped) going to the coil. Refer to your service manual, or reconnect the battery and use a test light or voltmeter. The switched +12 volt wire will be hot when the ignition key is turned on. 2. Refer to Figure 5. Connect the HI-4 red wire and switched +12 volt wire to Coil positive. 3. The HI-4 white wire is not used and should be taped. 4. Connect the HI-4 black wire to the Coil negative terminal. 5. Connect the HI-4 green wire to the vacuum switch (Figure 3, item 18), if used. 6. Connect the HI-4 brown wire to the tach wire, if equipped with tach. Tape up if unused. 7. The HI-4 is grounded via the timing housing; a separate ground connection is not required. 8. Reconnect battery ground cable. Verify proper ground connections to the frame and engine. VOES HOOKUP The OE vacuum switch (VOES) is normally an open circuit. Above 3-5 inch-Hg vacuum, the VOES closes and grounds the vacuum input on the OE ignition module. This increases the total advance generated by the OE ignition module. Vacuum advance improves part throttle 17 16 1. Cover Screws (2) 2. Ignition Timer Cover 3. Ignition Module 4. Timer Plate Screws (2) 5. Washers (2) 6. Screws & Washers (2 each) 7. Shield 8. Sensor 9. Trigger Rotor Bolt 10. Timer Plate 11. Trigger Rotor 12. Advance Assembly 13. Gear Case Cover 14. Ignition Coil 15. Spark Plug Wires (2) 16. Ignition Coil Terminal (FX) 17. Ignition Coil Terminal (FL) 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 NOTE: Most motorcycle coils do not have terminals marked. Use either terminal for Coil+ (positive) and the other one for Coil- (negative). Warning: The HI-4 (8-1100) Dual Fire ignition will not work with 2 plugs per head, dual coil application. Damage will result if attempted. Use the HI-4 (8-2100) single fire ignition for 2 plugs per head applications

Incoming search terms:

Incoming search terms: