852 steel bar info co ltd email com hk mail

You search Auto repair manual PDF 852 steel bar info co ltd email com hk mail, if there are search results will appear below. If search results do not exist, please search by others keyword.





V-Star 1100 And Dragstar 1100 Modification V-Star Driving/ Passing Lights Factory Chrome Light Bar Cover Installation

0

Filed Under (Yamaha) by admin on 08-11-2010

download
Modify your factory light bar cover to fit on Yamaha brand driving/passing lights. Use a rotary tool to widen the fastening area of the lower backside clips on the cover. The total width between the clips should be 4 æ inches. Trim off º inch on both inside ends of the lower backside attachment clips. Trim the clips equally. The following picture shows a modified cover. Narrow the clips on both ends to fit over the welds on the bar. The cover will not attach to the bar if the width between the clips is too narrow. If the width is too wide the cover may slide sideways on the bar. Narrow both clips equally to center the cover over the welds on the lower edge of the bar. The top of the cover is modified to allow the cover to fit over the bolts on the light bar. The top edge of the cover is filed æ inch deep and 5/8 inch wide to fit over the bolts. The back top edge is filed or ground 1/8 inch to fit over the light bar fastening bracket. Use care when filing chrome covered plastic. The following picture will help to complete this step in the modification. Modify your factory light bar cover to fit on Yamaha brand driving/passing lights. The ends of the cover are modified to allow the cover to fit over the upward curved light bar. The upper openings on the ends of the cover that fit over the bar must be filed to enlarge the area. Grinding the cover ends will allow the cover to fit and clip onto the bar. The end openings are filed or ground at an angle to match the slope of the bar. This picture shows the outer end of the cover. The ends of this cover have been modified by enlarging the area on the upper edges to fit over the upward curving light bar. The ends must be enlarged 1/8 inch on the top edge. The cover edge can be slanted upward to match the curved bar. Modify the cover ends until it fits without the outer chrome cover touching the bar. Modify your factory light bar cover to fit on Yamaha brand driving/passing lights. Sometimes the modified light bar cover may touch the bottom of the headlight. Modify the cover, or adjust the bar or headlight if you notice the headlight touching the bar cover. This modification makes the V-Star motorcycle with Yamaha driving lights look better. The light bar bolts are covered and the chrome cover improves the appearance of the front of your bike. Other V-Star riders will notice how nice the front of your bike looks with the chrome light bar cover installed

Incoming search terms:

Kawasaki VN1600 Highway Bar INSTALLATION AND OWNER'S MANUAL

0

Filed Under (Kawasaki) by admin on 25-10-2010

download
PREPARATION 1. Insure that the motorcycle is on flat level ground. 2. It is recommended that the motorcycle sit for at least one hour prior to installation to allow the engine to cool. During installation tight all fasteners to hold. Wait until you check all clearances and operation of the brake and shift lever to firmly tighten and torque all fasteners. INSTALLATION Right Side Highway Bar 1. Remove the front floor board bolt (M10). (14mm Socket) Figure 1. Right and Left side of Motorcycle is determined while sitting on the bike.
MAINTENANCE / CAUTION The high quality chrome finish of your National Cycle Chrome Highway Bar can be maintained with any quality chrome cleaner and / or polish applied with a soft cloth. Check hardware for tightness regularly. Never ride with loose mounting hardware. Check to be sure your Highway Bar does not contact any part of the motorcycle at a full turn left and right. Correct any problem before using the motorcycle. ©2005 National Cycle, Inc. PO Box 158, Maywood, IL60153-0158 USA 708-343-0400 / Fax: 708-343-0625 / www.nationalcycle.com / e mail: info@nationalcycle.com Page 2 of 2 10-114857-000 09/05 Install Upper “U” Bolt 2. Place “U” Bolt between the radiator and the down tube at the location shown in Figure 2. Threaded ends of “U” will face out- ward. 3. Select the right side Highway Bar. 4. Loosely install the Highway Bar at the lower mount point using the stock screw. (14mm Socket) Figure 3. While installing the Whizlock Nuts in the following Step #5 , be certain to tighten the nuts evenly, alternating left and right as you tighten. When complete you want the same amount of threads exposed on the ends of the “U” to insure the bolt does not rotate. 5. Install the upper Highway Bar with Whizlock Nuts. (1/2″ Socket) Figure 4. Orient assembly so Whizlock Nuts face outside. Firmly tighten after all clearances are checked. LEFT SIDE INSTALLATION 6. Repeat Steps 1 and 2. On the Left Side due to tight clearances between the radiator and the down tube you must locate the point where the radiator is “notched out” slightly. Figure 5. 7. Select the left side Highway Bar. 8. Repeat Steps 4 and 5.

Kawasaki VN2000 LIGHT BAR INSTALLATION AND OWNER'S MANUAL

0

Filed Under (Kawasaki) by admin on 25-10-2010

download
1. Make certain the motorcycle is securely positioned for this installation. Cover the front fender with a protective cloth to avoid scratches. 2 . Remove caps that cover the headlight screws. Remove headlight screws. (Small Screwdriver and #2 Phillips Screwdriver) Figure 1 and 2. 3. Disconnect headlight at two places. Set light aside. Figure 3. 4. Disconnect the Right (Orange) and Left (Blue) turn signal connectors. 5. Remove the Screws with the 8mm hex head that hold the turn signal bar to the under side of triple clamp. Remove turn signal bar. Bar and screws will not be re-used. (8mm Socket) Figure 4. PREPARATION INSTALLATION 6. Mount the Light Bar Assembly. Hold Light Bar in place at underside of triple clamp. Use the M6 x 16 Screws with a Flat Washer to install the Light Bar assembly. Tighten Firmly. (5mm Hex Key) Figure 5. 7. Route the Light Bar Wires to the back and into headlight shell. WIRE LIGHT BAR HELPFUL WIRE TIPS: A. Keep the Right and Left Wires of the Light Bar in separate groups. B. Inside the headlight shell, the wires bundled in the Blue Connectors are for Right side operation and Orange Connector is Left. C. You will need to remove 2-3″ of electrical tape from the Blue/Yellow Stripe, Low Beam Wire inside the headlight to have room for two Scotchlok Connectors going to this wire. (Scissors) Figure 6

Kawasaki Nerf Bar / Heel Guard INSTALLATION INSTRUCTIONS

0

Filed Under (Kawasaki) by admin on 24-10-2010

download
Set/Lock rear parking brake on bike and turn gas petcock to ‘Off’ position. Make sure vehicle is secure while installing the Nerf Bar. b) Remove and discard Foot Peg Bolts 3. Install Webbing: a) Install Web Straps on Welded Tabs: see fig #1 Note: see drawing for correct orientation of the web strap assembly to the nerf bar tabs. From the top, slip each web strap down and through the (2) nearest tab slots against the nerf tube. From the bottom, pull the web strap up and out through the middle slot until snug and in-line with tabs. 4). Install Nerf Bar / Heel Guards: Right Side: “Loosely” install following hardware. see fig #2 a) Install (1) Item #10 Foot Peg Weldment to Frame using (2) Item #2 Bolts, (2) Item #12 Washers, and (1) Item #6 Spacer. b) Slide Rear of Nerf Tube over (1) Item #9 Steel Foot Peg Mount Tube and position Front Nerf Bar Tube into ATV frame. c) Attach Rear Nerf Tube Hanger Bracket to OEM Foot Peg using (1) Item #4 Bolt, (1) Item #10 Washer, and (1) Item #5 Nut Left Side: “Loosely” install following hardware. a) Install (1) Item #10 Foot Peg Weldment to Frame using (2) Item #2 Bolts, (2) Item #12 Washers, and (1) Item #6 Spacer. b) Slide Rear of Nerf Tube over (1) Item #9 Steel Foot Peg Mount Tube and slide Front Nerf Bar Tube into Right Nerf Tube. c) Attach Rear Nerf Tube Hanger Bracket to OEM Foot Peg using (1) Item #4 Bolt, (1) Item #10 Washer, and (1) Item #5 Nut Front Side: With the Front Left Nerf Bar Tube inserted into the Front Right Nerf Tube attach (2) Item #3 Bolts and (2) Item #11 Washers. (both sides)

Harley-Davidson FXWG, FXST (all except FXSTS), FXDWG Light Bar INSTALLATION AND OWNER'S MANUAL

0

Filed Under (Harley Davidson) by admin on 20-03-2012

download
1. Put a pair of male and female clamp halves together just above the lower triple-clamp. Squeeze the ends of the clamp together with a pair of pliers. Diagram A. 2. Have an assistant position the Light Bar Assembly so the lightbar bracket is to the outside of the clamp assembly. Make sure the wires from the Light Bar Assembly are below the lower triple clamp. Diagram B. 3. Insert a Screw through the clamp and Light Bar Assembly mounting bracket and thread on an Acorn Nut. 4. Hold the Light Bar Assembly in place in front of the lower triple clamp, assemble and attach the remaining clamps. 5. With all four clamp assemblies in place, tighten the clamping screws and nuts to 15 ft. lbs. (21 Nm). Refer to the service manual to gain access to the wire harness inside the fuel tank tunnel or inside the frame backbone. Also, verify the appropriate color wires for hook-up of the passing lamps and turnsignals and running lights. Route the wires from the Light Bar Assembly, around the lower triple- clamp, and up to the frame backbone. Secure the wires so they cannot become pinched when turning the fork. A. The short black wires from the Light Bar Assembly connect to the wires powering the running lights. B. The short red wires from the Light Bar Assembly connect to the wires powering the turnsignals. C. The long blue wires from the Light Bar Assembly connect to the wire powering the headlight low beam. After the wires are connected, verify the operation of the passing lamps, running lights and turnsignals. Correct any connection problems before reassembling the motorcycle. Reinstall the fuel tank. Check all fasteners used during this installation for tightness

HARLEY DAVIDSON LIGHTED CHROME DIRECTIONAL BAR INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 15-03-2011

download
INSTALLATION 1. Disconnect turn signal wires at connectors located in directional bar. On 1994 and later models there are two wires for each turn signal lamp. Earlier models have only 1 wire per lamp. 2. Remove existing directional bar from motorcycle. Save all hardware for reattachment. If the turn signal connector is too large to be removed from the directional bar, remove the wires from the connector as follows: Bend back the connector latches on the sides of the connector slightly to free the secondary lock. Rotate the secondary lock outward on hinge to access terminals in chambers of connector housing. With a paper clip sharpened to a chisel point, insert the paper clip into the connector housing cavity until it stops. Pivot the end of the paper clip and gently tug on the wire to pull the terminal from the cavity. Do not tug on the wire until the tang that holds the terminal in the cavity is released. Take your time, a few tries may be required before you develop a feel for releasing the terminal from the connector. 3. Remove screws that mount turn signals lamps to existing directional bar. Remove lamps and turn signal wires (with their attached connector halves) from existing bar. 1 2 3 4 is02199 1. Ground wire 2. Hold lamp in place 3. Backing plate 4. Self-tapping screw Figure 1. Remove Backing Plate 4. See Figure 1. For each end of new directional bar, remove self-tapping screw that holds corner of backing plate and ground wire in place and remove backing plate. 1 2 is 02200 1. Hold lamp in place with this screw 2. Turn signal connector(s) are behind LED Figure 2. Assembling Directional Bar 5. See Figure 2. For each end of bar, place turn signal lamp in position with wires routed as shown. Move LED light out of the way and thread 5/32 inch Allen socket screw into lamp to hold lamp in place. Tighten screw.

Incoming search terms:

HARLEY DAVIDSON TOURING DETACHABLE SISSY BAR UPRIGHTS INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 10-02-2011

download
INSTALLATION NOTE The Detachable Sissy Bar Upright can be installed on either a two-point or four-point Docking Kit. 1. If not already in place, install the Detachable Docking Hardware Kit (either two-point or four-point) to the vehicle per the instructions in that kit. 2. See Figure 2. While standing behind the motorcycle, place the left-side and right-side front upright notches (with bushings in place) onto the docking points (A) inboard of the upper shock absorber mounts. Make sure the notch bushings (9) seat fully into the shock absorber docking points. 3. See Figure 2, arrows (D) and (E), and Figure 1. Position the rotary latches (4) over the rear docking points (3). Check to be sure the upright sides (1) and latches fit into the neck (7) of the rear docking points as shown. This may require some gentle squeezing or spreading of the sissy bar upright sides. NOTE After installing the sissy bar upright, check to be sure the sissy bar is secure. The front and rear docking points must be fully engaged. See Figure 1 for correct engagement. 4. Push the rear of the sissy bar downward and close the latches by pressing the latch lever as far forward as it will go. You will hear a “CLICK” when the latch is in place. If the latch does not easily close, do not force. Check the sissy bar alignment again, as described in steps 2 and 3. 5. To remove the sissy bar upright, press the release button (G) on each side and pull the latch levers back. Carefully lift the rear of the sissy bar up and pull the upright out of the front docking points

HARLEY DAVIDSON NARROW CHROME DIRECTIONAL BAR INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 06-02-2011

download
This kit is designed for installation on 1986 and later FLST®, FLSTC®, FLSTN®and 1991 and later Touring models. (Except 2004 and later FLHRS®and FLTR®) NOTE: Will not fit when equipped with Flat Lens Turn Signal Module (Part Number 91699-99A). Installation 1. Disconnect turn signal wires. For 1999 and later models: See Figure 1. Remove taillight cover and disconnect turn signal wires at connectors shown in illustration. For 1998 and earlier models: Disconnect turn signal wires at connectors located in directional bar. On 1994 and later models there are two wires for each turn signal lamp. Earlier models have only 1 wire per lamp. 2. Remove existing directional bar from motorcycle and save hardware for re-installation. If the turn signal connector is too large to be removed from the directional bar, remove the wires from the connector as follows: Bend back the connector latches on the sides of the connector slightly to free the secondary lock. Rotate the secondary lock outward on hinge to access terminals in chambers of connector housing. With a paper clip sharpened to a chisel point, insert the paper clip into the connector housing cavity until it stops. Pivot the end of the paper clip and gently tug on the wire to pull the terminal from the cavity. Do not tug on the wire until the tang that holds the terminal in the cavity is released. Take your time, a few tries may be required before you develop a feel for releasing the terminal from the connector. 3. Remove screws that mount turn signals lamps to existing directional bar. Remove lamps and turn signal wires (with their attached connector halves) from existing bar. 4. Position directional bar in mounting location at rear fender and secure bar to motorcycle using original hardware removed in step 2. Route turn signal wires from motorcycle back into directional bar, or up to taillamp (if 1999 and later model) and mate connectors. If the wires were removed from the connector in step 2, insert the terminal ends of the wires into the connector until they snap in place, then mate connector halves.

HARLEY DAVIDSON SISSY BAR UPRIGHT KITS INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 03-02-2011

download
INSTALLATION 1. Install sissy bar upright kit following the appropriate side- plate instruction sheet. 2. If using sissy bar upright with backrest pad, install pad before applying medallion. 3. Clean surface of sissy bar upright using a 50/50 isopropyl alcohol/water solution. Allow surface to dry thoroughly before continuing. NOTES Test placement of medallion on sissy bar upright before installation. Do not remove adhesive backing until ready to apply. The ideal temperature should be at least 60° F (16° C) for proper adhesion of the medallion on the sissy bar upright. 4. Peel off adhesive backing on bar and shield logo medallion (1) and apply to sissy bar upright (2). Press firmly in place for 10 to 15 seconds. 5. Allow the adhesive to cure for 12 hours at no less than 60° F (16° C). 6. Refer to appropriate sideplate instruction sheet for torque specifications. SERVICE PARTS

HARLEY DAVIDSON SISSY BAR MOUNTED AUXILIARY BRAKE AND TAIL LIGHT INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 07-02-2011

download
These kits fit 1999 and later XL models, 1996 and later Dyna™ and 1996 and later Softail models (except 2006 FXSTC) equipped with a Medallion Plate-Style Sissy Bar Upright. Will not fit with Backrest Pads that have mounting brackets that match the contour of the sissy bar medallion. Will not fit with sissy bar mounted storage bags INSTALLATION 1. Follow the instructions in the Service Manual to remove the seat. To prevent accidental vehicle start-up, which could cause death or serious injury, disconnect negative (-) battery cable before proceeding. (00048a) Disconnect negative (-) battery cable first. If positive (+) cable should contact ground with negative (-) cable connected, the resulting sparks can cause a battery explosion, which could result in death or serious injury. (00049a) 2. Disconnect battery cables, negative (-) cable first. 1 2 is 01457 1. Adhesive mounted medallion 2. Push nut mounted medallion Figure 1. Medallions 5 2 1 3 4 is 01458 1. Screw 2. Screw (2) 3. Backrest bracket 4. Backrest pad 5. Mounting hole spacing (center to center) Figure 2. Backrest Pad and Bracket -J03063 1 of 5 Remove the Backrest Pad NOTE Medallions are attached to a medallion plate between the uprights of the sissy bar using either adhesive or push nuts. 1. See Figure 1. Remove and retain any existing medallion. Adhesive Mounted Medallion (1): Carefully pry the medallion (1) from the plate. Remove any adhesive residue from the back of the medallion and the sissy bar medallion plate. To avoid contaminating the adhesive backing, place the medallion in an area away from dirt and debris. Push Nut Mounted Medallion (2): Carefully pry the edge of the medallion until the medallion is free of the push nuts. 2. See Figure 2. Remove and retain the screw (1) that secures the backrest pad to the plate. 3. Remove and retain the two screws (2), backrest bracket (3) and backrest pad (4). Install the Light Assembly 1. See Figure 3. Clean the front of the medallion plate (2) with a 50/50 solution of isopropyl alcohol and water. 2. Peel the adhese bracket kit (Part Number 59545-04) and sandwich the light assembly between the bracket frame and the medallion plate. The bracket clamps will fit around the back of the sissyive backing from the adhesive tape located on the light assembly (1). Fit and hold the light assembly to the front of the medallion plate (2). 3. See Figure 6. For 2.55 inch (64.8 mm) center to center mounting hole backrest pads, use th bar arms.

Incoming search terms: