9 inch motorcycle headlight

You search Auto repair manual PDF 9 inch motorcycle headlight, if there are search results will appear below. If search results do not exist, please search by others keyword.



  9 inch motorcycle headlight Direct Download speed 5282 Kb/s

  9 inch motorcycle headlight Full Version speed 6162 Kb/s



Ducati SPORT TOURING HEADLIGHT UPGRADE INSTALLATION AND REMOVAL INSTRUCTIONS

0

Filed Under (Ducati) by admin on 25-10-2010

download
1. Remove the following fairing components per the instructions in the Ducati owners manual: • Instrument surrounds • Headlight fairing • Chin fairing (under headlight/air intake) • Right-side middle fairing (covers battery) 2. Disconnect the speedometer cable from the speedometer. Unthread the ring nut at the top of the speedometer cable and retract the cable downward about 4-6 inches. 3. Disconnect the headlight wiring from the headlight bulbs. Retract the rubber boots at the rear of the headlight assembly to gain access to the wire terminals. Note that the two ¼ inch terminals at the high- beam bulb have locking clips that should be depressed before pulling the terminal away from the bulb. 4. Unplug the parking light from the headlight body by grasping the wires and carefully pulling it out. 5. Remove the two rubber plugs covering the lower headlight mounting screw access holes beneath the air intake horn. 6. Using an 8mm hex socket inserted through the lower access holes remove the two hex-head bolts securing the bottom of the headlight to the frame. 7. Using the same socket wrench, remove the two 8mm hex-head bolts securing the top of the headlight assembly to the frame. 8. Remove the headlight assembly from the frame. 9. Remove the two rubber grommets and steel reducing sleeves from the frame at the top mounting locations for the headlight. Leave the lower pair in place; these will be re-used, as shown in Figure 6

Incoming search terms:

1300 Yamaha V-Star Installation Manual

0

Filed Under (Yamaha) by admin on 07-11-2010

download
1) Place motorcycle on a firm level surface and secure in a upright position. 2) Remove saddle bags and saddle bag hardware (Tourer model only) Also remove rear riders pegs (Tourer model requires removal of rear footpeg offset hardware as well) 3) Attach bracket A (right) / B (left) to rear footpeg attachment point using new bolts provided. Remount footpegs/saddlebag hardware over top of brackets A/B. NOTE: Do not attach leveling stand bracket at this time 4) Attach bracket C(right) / D(left) to rear fender sub frame using new bolts provided. (Tourer model only – Saddle bag hardware mounts to the outside of brackets C/D. Brackets C/D mount between chrome side rail and saddlebag hardware.) NOTE: Brackets C/D have welded spacers which attach in toward rear fender 5) Attach top of Bracket E(right) / F(left) to rear of brackets C/D. Brackets E/F mount to the inside of brackets C/D. NOTE: Use ½ inch spacer between brackets E/F and C/D on Tourer model ONLY
6) Attach rear of brackets A/B to TOP of forward hitch arms. Attach bottom to brackets E/F to rear hitch plate. 7) Carefully tighten all bolts at this time ensuring hitch is square with motorcycle. Hitch Bracket Identification Leveling stand screw jack installation 1) Attach leveling stand brackets to brackets A and B 2) Thread right side screw jack into threaded hole on leveling stand bracket attached to bracket A sand adjust leveling jack bolt out. 3) Push motorcycle over from left side until right screw jack is touching floor. 4) Thread left side screw jack into threaded hole on leveling stand bracket attached to bracket B and adjust out until motorcycle will rest upright on both screw jacks. 5) Adjust screw jacks until motorcycle is level. 6) After InstaTrike is attached to or removed from receiver hitch, be sure to remove leveling stands and leveling stand brackets. CAUTION – Use screw jacks to hold motorcycle upright and level ONLY. Do not lift motorcycle with screw jacks. CAUTION – Use care when installing screw jacks. Be certain that motorcycle is always in a stable balanced position.
INSTALLATION OF THE TOW-PAC HITCH CART. 1. Place your motorcycle on a smooth flat surface, like a garage floor, and install leveling stands. Install right leveling stand first. Carefully raise motorcycle off of side stand and install left leveling stand. Caution – Use leveling stands to level motorcycle ONLY. Do not raise motorcycle with stands Caution – Be certain that motorcycle is always in a stable balanced position when installing leveling stands. 2. Assemble the axles, tires and wheels, and fenders onto the tow- pac hitch cart. 3. Carefully align the tow-pac hitch cart’s hitch mount with the receiver hitch on the motorcycle. Now push the hitch mount into the receiver hitch. (this might be a little difficult until you get use to doing it. Removing the paint from the hitch mount and applying a little grease will help.) 4. Place the hitch pin through the receiver hitch and hitch mount ( alignment plate ). Install and tighten the tension bolt

Incoming search terms:

Vengeance Motorcycle Specification And Owner's Manual

0

Filed Under (Vengeance) by admin on 20-11-2010

download
Vengeance Maxis • Vengeance Raven • Vengeance Banshee • Vengeance Whiplash • Hotrod Drifter • Hotrod CalChop • Hotrod Teacher • Hotrod Bone Shifting Gears Starting off and changing gears requires coordination of the clutch and throttle and gearshift lever. If you don’t do things right, the amount of control you have over the bike is lessened. To start off, pull in the clutch, shift into first gear, roll on the throttle a little, and ease out the clutch. You will become familiar with the friction zone (that’s where the clutch begins to take hold and move the bike), and you add a bit more throttle. You don’t want to stall the engine, nor do you want to over-rev it. There’s a sweet spot in there; find it. Shift while traveling in a straight line. Shifting in a curve is not good practice, and something to be avoided. Become familiar with the sound of your engine, so you can tell when you should shift without looking at your instruments. When you downshift to a lower gear, you should (in one swift, smooth movement) be able to squeeze the clutch, rev the engine a little to let it catch the lower gear smoothly, and shift down. When you come to a stop in traffic, leave the bike in first gear with the clutch disengaged (just in case you want to accelerate out of there in a hurry). Who knows what may be coming up behind you. Braking Don’t ever forget: The front brake on your motorcycle can supply as much as 70 percent or more of your stopping power. The single most important thing you can learn about braking is to use that front brake every single time you want to slow down. Turning When you are riding along the road, you lean a motorcycle into a turn. Learning to lean is an essential part of riding a motorcycle. It is a normal function of the bike when you are changing its path of travel – and quite different from turning the steering wheel of your car. To get the motorcycle to lean in a normal turn, press the handlebar in the direction of the turn and maintain slight pressure on that handlebar to take you smoothly through that particular turn. In other words: press right to go right; press left to go left. Your instincts to keep the motorcycle on a smooth path while keeping it from falling over usually take care of this without you even noticing it. (Demonstrate to yourself how a motorcycle moves by pressing a handlebar slightly while traveling in a straight line. The motorcycle will move in the direction of the handlebar you pushed.) • Slow down before you enter the turn; look as far ahead as possible through the turn. • Keep your feet on the pegs, and grip the gas tank with your knees. • Lean with the motorcycle; don’t try to sit perpendicular to the road while the motorcycle is leaning over. • Keep an even throttle through the turn, or even accelerate a little bit. Checking the Bike before the Ride It’s not fun to have things go wrong on a motorcycle, but if you spend a minute before you go off on a ride, you can increase the chances that nothing will.

Incoming search terms:

YAMAHA V-MAX PERIODIC MAINTENANCE AND MINOR REPAIR

0

Filed Under (Yamaha) by admin on 25-11-2010

download
PERIODIC MAINTENANCE AND MINOR REPAIR -. 1. Screw (x 2) EAU03003 Replacing the headlight bulb This motorcycle is equipped with a quartz bulb headlight. If the headlight bulb burns out, replace it as follows. 1. Remove the headlight unit by re- moving the screws. 2. Disconnect the headlight coupler, and then remove the headlight unit and bulb cover. 1. Headlight bulb holder 3. Remove the headlight bulb holder by turning it counterclockwise, and then remove the defective bulb. EWOOOl19 Headlight bulbs get very hot. Therefore, keep flammable products away from a lit headlight bulb, and do not touch the bulb until it has cooled down. 4. Place a new bulb into position, and then secure it with the bulb holder. 1. Do not touch this area. EC000105 Do not touch the glass part of the headlight bulb to keep it free from oil, otherwise the transparency of the glass, the luminosity of the bulb, and the bulb life will be adversely affected. Thoroughly clean off any dirt and fingerprints on the headlight bulb using a cloth moistened with alcohol or thinner. 5. Install the bulb cover, and then connect the coupler. 6. Install the headlight unit by install- ing the screws. 7. Have a Yamaha dealer adjust the headlight beam if necessary. 6-40 PERIODIC MAINTENANCE AND MINOR REPAIR 1. Screw (x 2) 1. Tail/brake light bulb (x 2) EAU00855 Replacing a turn signal light bulb or the tail/brake light bulb 3. Insert a new bulb into the socket, push it in, and then turn it clock- wise until it stops. 1. Remove the lens by removing the screws. 2. Remove the defective bulb by pushing it in and turning it counter- clockwise. 1. Turn signal light bulb 4. Install the lens by installing the screws. EC000108 Do not overtighten the screws, oth- erwise the lens may break

Incoming search terms:

Motorcycle LED lights RENEGADE LIGHTS Disconnection Guide

0

Filed Under (Tips and Review) by admin on 29-01-2011

download
1. Make sure your bike is cool and parked on a flat secure surface! 2. Find your battery (you may have to remove your seat or side covers in order to get to your battery) Disconnect the NEGATIVE ( -) cable. Negative battery cable must be disconnected from the battery in order to avoid safety hazards! Be sure as you disconnect the Negative cable that it does not touch or make contact with your Positive terminal 3. Disconnect the fuse holder from the battery – both the positive ( +) and negative ( -) sides. 4. Cut the wire to the light that is not working with the side cutters. 5. At the problem light twist the light case back and forth slowly and then pull firmly, DO NOT yank to remove from the motorcycle. 6. If the motorcycle led light does not come off easily, repeat the twisting motion back and froth until you feel the light loosen – then pull. 7. Pull the motorcycle led light away from the motorcycle slowly until the cut end of wire falls free. 8. If you will NOT be using your motorcycle until the new lights arrive, you may stop at this step. SAFETY POINT: Otherwise, where you cut the wire, you need to dead end or tape the cut wire. This will keep it from shorting out until the new motorcycle led light is installed. 9. Reconnect fuse holder to battery. 10. Reconnect the battery and then install the seat. 11. Return the motorcycle led light or lights to Renegade Lights along with Warranty Return Policy Form. 12. Renegade Lights will return your new motorcycle led lights along with instructions for installing them.

Incoming search terms:

HARLEY-DAVIDSON MOTORCYCLE WASH KIT MANUAL

0

Filed Under (Harley Davidson) by admin on 02-03-2011

download
THE WASHING PROCESS Allow the motorcycle to cool to the touch. Cool water can damage a hot motorcycle. 1. Pre-Wash: a. Verify the motorcycle is cool to the touch. b. Rinse the motorcycle from the bottom up. c. Verify you have the proper cleaning supplies. d. Spray on Bug Remover and let the product activate while proceeding to the next step. 2. Wheels and Tires: a. Rinse wheel and tire surfaces. b. Apply Wheel and Tire Cleaner. c. Wait one minute after spraying product. d. Clean wheel with a Soft Detailing Pad or Wheel and Spoke Brush. e. Rinse well. 3. The Wash: a. Have two buckets; one for the cleaner and one for rinsing. b. Pour Sunwash into the Harley-Davidson Cleaning Bucket and fill with water. c. Fill the rinsing bucket with clean, plain water. d. Soak the Wash Mitt in the Sunwash solution. e. Wash all surfaces from the top working down. f. Rinse from the bottom up first. g. End with top down rinse. 4. Drying the Motorcycle: a. Use the Soft Drying Towel to dry surfaces of the motorcycle. b. Dampen the towel in clean water. c. Wring out the towel as often as needed and continue until the surface is completely dry. 5. The Polish and Seal : (not applicable for denim paint finishes) Polishing and sealing isn’t just about good looks . A well cared-for motorcycle repels dust, dirt, bugs and dirty water. a. Use Harley Glaze polish and sealant and follow the instructions on the bottle. b. Use Softcloth disposable towels for application. c. A Softcloth or Microfiber detailing cloth is an absolute must for finish buffing. d. In between Harley Glaze applications, use Harley Spray Cleaner and Polish and Harley Gloss to maintain shine and protection of painted and chrome fin- ishes.

Incoming search terms:

Motorcycle LED lights RENEGADE LIGHTS Installation Guide

0

Filed Under (Tips and Review) by admin on 29-01-2011

download
1. Make sure your bike is cool and parked on a flat secure surface! 2. Find your battery (you may have to remove your seat or side covers in order to get to your battery) Disconnect the NEGATIVE ( -) cable. Negative battery cable must be disconnected from the battery in order to avoid safety hazards! Be sure as you disconnect the Negative cable that it does not touch or make contact with your Positive terminal 3. Your new motorcycle LED lights are polarity sensitive–meaning that the RED wires on the LEDs must be hooked to the Positive (+) terminal and the BLACK wires must be hooked to the Ground (-) . All Red Wires must go to a common power wire and ALL Black Wires must go to a common ground. You cannot run the LED motorcycle lights in a series nor can you run the wires from one motorcycle LED light to another in a loop type installation. ( All of the wires on the motorcycle LED lights which you install will end up together in one place at your battery.) 4. Pick a hidden flat surface around the front of your seat area to mount the switch. ( You must be able to reach the switch when the seat and/or side covers are back on your bike.) You will install your switch later using the double-sided tape provided to you. 5. Next, begin choosing the locations where you would like to mount your motorcycle LED lights. Choose areas which will give you the most light coverage overall, but which will allow the motorcycle LED lights itself to be hidden from easy view when you are standing back and looking at the bike. 6. Clean each area where you choose to place a motorcycle LED light with the alcohol based cleaner making sure all dirt and/or oil is removed from that area

Incoming search terms:

2004 Vengeance MOTORCYCLE OWNERS MANUAL

0

Filed Under (Vengeance) by admin on 21-11-2010

download
Vengeance Warrior • Vengeance Raider • Vengeance Vertebreaker • Vengeance Striker • Vengeance Vendetta • Vengeance Vindicator Shifting Gears Starting off and changing gears requires coordination of the clutch and throttle and gearshift lever. If you don’t do things right, the amount of control you have over the bike is lessened. To start off, pull in the clutch, shift into first gear, roll on the throttle a little, and ease out the clutch. You will become familiar with the friction zone (that’s where the clutch begins to take hold and move the bike), and you add a bit more throttle. You don’t want to stall the engine, nor do you want to over-rev it. There’s a sweet spot in there; find it. Shift while traveling in a straight line. Shifting in a curve is not good practice, and something to be avoided. Become familiar with the sound of your engine, so you can tell when you should shift without looking at your instruments. When you downshift to a lower gear, you should (in one swift, smooth movement) be able to squeeze the clutch, rev the engine a little to let it catch the lower gear smoothly, and shift down. When you come to a stop in traffic, leave the bike in first gear with the clutch disengaged (just in case you want to accelerate out of there in a hurry). Who knows what may be coming up behind you. Braking Don’t ever forget: The front brake on your motorcycle can supply as much as 70 percent or more of your stopping power. The single most important thing you can learn about braking is to use that front brake every single time you want to slow down. Always apply both the front and the rear brakes at the same time. If necessary, apply them hard, but not so hard that you lock up either wheel. A locked wheel, as well as causing the bike to skid, results in downright inefficient braking. Turning When you are riding along the road, you lean a motorcycle into a turn. Learning to lean is an essential part of riding a motorcycle. It is a normal function of the bike when you are changing its path of travel – and quite different from turning the steering wheel of your car. To get the motorcycle to lean in a normal turn, press the handlebar in the direction of the turn and maintain slight pressure on that handlebar to take you smoothly through that particular turn. In other words: press right to go right; press left to go left. Your instincts to keep the motorcycle on a smooth path while keeping it from falling over usually take care of this without you even noticing it. (Demonstrate to yourself how a motorcycle moves by pressing a handlebar slightly while traveling in a straight line. The motorcycle will move in the direction of the handlebar you pushed.)

Incoming search terms:

Ural Motorcycle Repair Manual

0

Filed Under (Ural) by admin on 11-11-2010

download
FLUID CAPACITIES TOURIST & -10 Models Sportsman Solo Gasoline tank 19 L / 5 Gal 19L / 5 Gal 18.5 L / 4.9 Gal Reserve 2L / 0.5 gal 2L / 0.5 gal 2L- / 0.5 Gal Engine crankcase 2 L / 2 qt. + 3.6 oz. 2.0L / 2.11 qt 2 L / 2 qt. + 3.6 oz. Gearbox 0.9L / 1 qt 0.9L / 1 qt 0.9L / 1 qt Final drive 110 ml / 3.85 oz. 150 ml / 5.25 oz. 110 ml / 3.85 oz. Telescopic Forks (-10 & solo models) N/A on Tourist N/A on Sportsman 135 ml / 4.56 oz. Shock Absorbers 105 ml / 3.55 105 ml / 3.55 oz 105 ml / 3.55 oz
RUNNING GEAR TOURIST / SPORTSMAN SOLO Frame Tubular welded Rear wheel suspension Swing arm with hydraulic spring shock absorbers Sidecar: same as -40 Solo: Lower spring rate Front fork Leading link Telescopic spring Sidecar Cushioned body (on rubber cushions) and wheel on long-lever suspension with hydraulic spring shock absorber N/A Brakes Shoe-type with mechanical drive on front, rear and sidecar wheels, front wheel has dual cams. Tires 4″ x 19″ Front & Side: 22 psi cold Rear: 36 psi cold 3.5″ x 18″ Solo: Front 25 psi cold Rear: 32 psi cold -10′s: Front & side: 25 psi cold Rear: 36 psi cold CLEARANCES mm in Valves with engine cold 0.05 0.002 Between spark plug electrodes 0.50 – 0.65 0.020 – 0.026 Between brake shoes and drum 0.3 – 0.70 0.012 – 0.028 Backlash between tooth faces of bevel gears in final drive 0.1 – 0.3 0.004 Between rotor and ignition pickup 0.3 – 0.4 .012 – .016 FREE TRAVEL / ADJUSTMENTS mm in Hand brake control lever 5 – 8 0.2 – 0.3 Clutch control lever 5 – 8 0.2 – 0.3 Foot brake drive pedal ¼ of full stroke of pedal, 25 – 30 1.0 – 1.2 Toe-in throughout motorcycle center distance (exception: Sportsman 0 ° toe-in) 10 N/A Angle of motorcycle inclination to vertical plane (camber angle of rear wheel) 1° away from sidecar N/A Headlight installation (with motorcycle laden) horizontal (high beam) TORQUE SPECIFICATIONS Metric (in repair manual) US Equivalent Location on Bike 29 to 33 Nm 22 ft/lb. to 30 ft/lb. cylinder heads 22 to 25 kgf-m 175 ft/lb. to 185 ft/lb. fly wheel tightening screws 3.8 to 4.2 kgf-m 30 ft/lb. to 40 ft/lb. cylinder 2.1 to 3.0 kgf-m top 14 ft/lb. to 22 ft/lb. shock absorber 3.6 to 5.0 kgf-m bottom 28 ft/lb. to 36 ft/lb. shock absorber 3.0 to 3.4 kgf-m 22 ft/lb. to 26 ft/lb. bearing nut 3.0 to 3-4 kgf-m 22 ft/lb. to 26 ft/lb. final drive to swing arm bolts 1.6 to 1.8 kgf-m 12 ft/lb. to 14 ft/lb. oil pump bolt .8 to 1.0 kgf-m 5 ft/lb. to 8 ft/lb. engine sump 1.4 to 1.8 kgf-m 10 ft/lb. to 14 ft/lb. final drive case nuts 7 to 9 kgf-m 50 ft/lb. to 66 ft/lb. nut fastening the pinion bearing 2.2 to 2.8 kgf-m 16 ft/lb. to 20 ft/lb. reverse gear brake lever 1.8 to 2.0 kgf-m 14 ft/lb. to 16 ft/lb. generator gear nut 14.0 to 16.8 kgf-m 100 ft/lb to 120 ft/lb steering stem nut CONVERSIONS To convert from mm to in, divide by 25.4 (there are 25.4 mm per inch). To convert from liters to gallons, divide by 3.785 (there are 3.78 liters per gallon). To convert from liters to quarts, multiply by 1.056 (there are 1.056 quarts per liter). To convert from liters to pints, multiply by 2.112 (there are 2.112 pints per liter). To convert from km to miles, multiply by .62 (there is .62 mile per km). To convert from km/hr to mph, multiply by .62. To convert from Newton-meter (Nm) to inch-pound, multiply by 8.86. To convert from cm 3 (cc) to pints, divide by 473 (there are 473 cc per pint). To convert Celsius to Fahrenheit, F° = C° x 1.8 = 32°. To convert Fahrenheit to Celsius,C ° = (F° – 32° ) divided by 1.8

Motorcycle stand Wheel chock set up and operating instructions

0

Filed Under (Tips and Review) by admin on 22-11-2010

download
1. can be adjusted to fit the wheel length. The Motorcycle Stand will fit most standard motorcycles currently on the market. However, some models with especially wide tires or custom low-profile front fenders will not fit. Mount the Support Arm (4) to the front of the Base using 2 Bolts (12), Washers 2. (5), and Nuts (6). Insert Pin (9) through the mounting holes and Cradle Stop (3); secure with Wash- 3. er (10) and R Pin (11). Insert Pin (9) through the mounting holes and Wheel Adapter (2); secure with 4. Washer (10) and R Pin (11). Securely tighten all hardware before use. 5. the Motorcycle stand must be mounted securely before use. 6. Page 5 SKU 97841 For technical questions, please call 1-800-444-3353. Mounting in concrete Choose a location to install the Motorcycle Stand that is flat, level, and capable of 1. bearing the combined weight of the Motorcycle Stand and the motorcycle being secured. The location should not obstruct walkways and provide enough room to retrieve the motorcycle after it is mounted. The surface of the location should be one suitable for the mounting of heavy equipment. Use the mounting holes in the Base (1) of the Stand as a template. Arrange the 2. Base in the chosen location and mark where the holes are to be drilled. You will need concrete anchors (not included) to secure the Base to the concrete 3. floor. Using the correct size concrete drill bit (not included), drill the mounting holes to secure the Base. Attach the concrete anchors to the floor. Secure the Base to the floor using con- 4. crete anchors.

Incoming search terms:

Incoming search terms: