92 harley ultra wire chart

You search Auto repair manual PDF 92 harley ultra wire chart, if there are search results will appear below. If search results do not exist, please search by others keyword.



  92 harley ultra wire chart Direct Download speed 5282 Kb/s

  92 harley ultra wire chart Full Version speed 6162 Kb/s



1982-2005 Harley Motorcycle Removal and Installation Instructions

0

Filed Under (Harley Davidson) by admin on 31-03-2012

download
” bolt from the mounting stem on the Signal® mirror. While seated on the motorcycle, position the Signal® mirror on the handle bar. Secure the Signal® mirror to the handle bar using the 5/ 16 ” bolt. Make sure the bolt is tight! Guide the Signal® mirror wire harness into the cowling by going along side the existing factory wire harness. 4 Remove any slack in the wire harness. Secure the wire harness to the handle bar using a supplied tie wrap. 5 6 Adjust the position of the Signal® mirror and tighten the ball retention screws. Remove the motorcycle seat. Remove the aft mounting bolts on the fuel tank. 7 Guide the Signal® mirror wire harness along the inside of the fuel tank’s front mounting bolt and between the crossover tube. 8 9 Lift up the aft portion of the fuel tank and guide the Signal® mirror wire harness down the backbone of the motorcycle frame, alongside the existing factory wire harness. The motorcycle’s electrical wiring for turn indicators is located aft of the gas tank on the backbone of the frame. Guide the new wire harness from the Signal® mirror to the electrical wiring. Cut off any excess slack in the wire. Locate the SOLID BROWN wire from the wire connector. Turn the ignition key so that electrical power is on and activate the right side turn indicator. Probe the wire with the wire tester to verify that flashing turn indicator power is present. Label that wire as ‘right side turn’. Repeat all of the previous steps to replace the left side factory mirror with the new Signal® mirror. Locate the SOLID VIOLET wire from the wire connector. Activate the left side turn indicator and probe the wire with the wire tester to verify that flashing turn indicator power is present. Label that wire as ‘left side turn

Incoming search terms:

HARLEY DAVIDSON DETACHABLE QUARTER FAIRING AND DOCKING HARDWARE KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 10-03-2011

download
Installation The rider’s safety depends upon the correct installation of this kit. Use the appropriate service manual procedures. If the procedure is not within your capabilities or you do not have the correct tools, have a Harley- Davidson dealer perform the installation. Improper installation of this kit could result in death or serious injury. (00333a) NOTE If your motorcycle has directional lights mounted on the upper fork bracket they must be relocated to the bottom fork bracket. Some models have front directional lights equipped with three wires, the third black wire is a ground wire. Check to determine how many wires are connected to the front directional lights and follow the following procedure that applies. Ifdirectional lights are not mounted on the upper fork bracket proceed to “ASSEMBLING FAIRING”. Relocating Two Wire Directional Lights 1. Support motorcycle on a center stand such that front wheel is raised slightly off the ground. 2. Remove fork tube pinch screw from right side of lower bracket. 3. Cut wires connected to right directional light about 2 in. away from directional light body. 4. Remove fork tube pinch screw from right side of upper fork bracket. (This is the screw that secures the right directional light.) 5. Install right directional light on right side of lower fork bracket using pinch screw removed in step 4. Install pinch screw removed in step 2 into right side of upper bracket. Tighten both pinch screws to 30-35 ft-lbs. 6. Repeat steps 1 through 5 to relocate left directional light. NOTE Fork tubes may slide downward within fork brackets. If this occurs, front fork tube extension above front fork upper bracket will have to be readjusted according to appropriate Service Manual procedures. 7. Connect the right directional light as follows: Strip approx. 5/16 in. of insulation from the wires cut in step 3. 8. Crimp solderless connectors from kit on two wires coming from motorcycle. 9. Split one end of the 2-conductor polarized wire from kit back about 2 in. and strip 5/16 in. of insulation from wire ends. 10. Slide a piece of shrink tubing from kit over each of the wire ends stripped in step 9 and crimp the wires into the terminals installed in step 8. Make sure you connect the silver and copper colored wires to like colored wires. NOTE Polarized wire is used in this application to ensure correct wiring. One wire is silver, one is copper colored. Wire colors of spliced wire must match wire color of original directional wire leads. 11. Cut polarized wires to the length required for connection to the wires at the relocated directional light. Make certain you leave enough slack in wires to allow routing the harness along the fork tube. 12. Split remaining end of the 2-conductor polarized wire from kit back about 2 in. and strip 5/16 in. of insulation from wire ends. 13. Slide heat shrink tubes over the two wire end. 14. Strip 5/16 in. of insulation from wires connected to directional light and connect like colored wires at directional light with connectors from kit. 15. Slide heat shrink tubing over connectors installed in steps 10 and 14. Activate shrink tubing with heat gun or hair dryer.

SR-C400 Motorcycle Security System INSTALLATION MANUAL AND USER'S GUIDE

0

Filed Under (Tips and Review) by admin on 29-01-2011

download
Routing the Antenna Wire The MCM includes an 18″ antenna wire. The first 12″ is a coaxial wire; the remaining 6″ is the reception antenna wire. When routing, try to avoid running the antenna along or near metal. For best performance, have the antenna wire as vertical as possible and exposed. Wire Connections The system includes one harness (HAR-1a) that connects directly into the MCM. The harness is split into three plugs: one for the GEN-1a connector, one for the optional SN-5 connector and one for the data output for future expansion. Note: Each plug is unique and will only fit the appropriate component one way. Main Harness Note: If the optional factory connector kit is being used, please disregard this section of the instructions and refer to the instructions supplied with the factory connector kit. The main harness consists of two harnesses. One is labeled (HAR-1a) and the second is labeled (GEN-1a). Plug in the white 4 pin connector from the (HAR-1a) into the matching 4 pin connector from the (GEN-1a). The (HAR-1a) also has a waterproof connector that plugs into the MCM. The wires should be connected as follows: HAR-1a Black wire with fuse and ring terminal – To battery Positive (+). GEN-1a Black wire – To ground (-). Orange wire – To tail light wire or any other wire that is hot (+) when ignition is ON (NOTE: this is an input to the alarm this connection is not designed to flash the tail light). Color Codes: Ground (-) Tail Light Honda Green wire Brown wire Kawasaki Black wire Red wire Suzuki Black/White Brown wire Yamaha Black wire Blue wire Harley Davidson Black wire Blue wire

Incoming search terms:

HARLEY DAVIDSON VRSC BRACKET FOR BILLET HEADLAMP SHELL REMOVAL AND INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 31-01-2011

download
REMOVAL VRSCA Models 1. Remove windshield (if equipped). Refer to appropriate Instruction Sheet for procedures. 2. Remove right side cover and maxi-fuse. Refer to MAXI- FUSE in Service Manual. 3. See Figure 1. Disconnect headlamp connector (1) from vehicle wire harness. 4. Remove two screws (2), headlamp mounting bracket (3), and headlamp assembly (4) from upper bracket. 2 3 4 5 1 is03046 1. Connector 2. Screw (2) 3. Bracket 4. Headlamp assembly 5. Screw (2) Figure 1. VRSCA Headlamp Assembly VRSCB Models 1. Remove windshield (if equipped). Refer to appropriate Instruction Sheet for procedures. 2. Remove right side cover and maxi-fuse. Refer to MAXI- FUSE in Service Manual. 3. See Figure 2. Disconnect headlamp connector (1) from vehicle wire harness. 4. Remove two screws (2), headlamp assembly (3), and headlamp mounting bracket (4) from upper bracket. 5. Remove nut (5), screw (6), and trim ring (7) from head- lamp. 6. Remove lens assembly (8) from headlamp shell (9). Save lens assembly for Billet Headlamp Shell Kit 67704-03 installation INSTALLATION 2004-Earlier VRSCA and VRSCB Models 1. Assemble Chrome Billet Headlamp Shell Kit (67704-03). Refer to Instruction Sheet-J03018. NOTES VRSCA models use Headlamp 68297-05, while VRSCB models use original equipment lens assembly (including gasket and boot). Adapter ring from kit (Figure 6, Item 1) will be used to install billet headlamp assembly on Instruction Sheet-J03018. 2. See Figure 3. Cut the two connectors (1) from existing headlamp wire harness (2). Be sure to cut the wires as close to the back of the connector as possible. 3. See Figure 6. Route new wire harness (2) through the hole in bottom of the billet headlamp shell (A). NOTE Only one 16 AWG wire will fit into pin terminals included in kit. Both black wires (ground) can be joined together, then connected to a single wire, if desired. 4. Tape end of one black wire with electrical tape and secure it to wire harness. 5. See Figure 3 and Figure 6. Install terminal pin (3) and socket housing (4) onto new wire harness (Figure 6, Item 2). Refer to MULTILOCK ELECTRICAL CONNECTORS in Service Manual for installing socket/pin terminals. 3 4 1 2 is03025 1. Connector (2) 2. Wire harness 3. Terminal pin (4) 4. Socket housing Figure 3. 2004-Earlier VRSCA and VRSCB Headlamp Wire Harness 2005-Later VRSCA and VRSCB Models 1. Assemble Chrome Billet Headlamp Shell Kit (67704-03). Refer to Instruction Sheet-J03018. NOTES VRSCA models use Headlamp 68297-05, while VRSCB models use original equipment lens assembly (including gasket and boot). Adapter ring from kit (Figure 6, Item 1) will be used to install billet headlamp assembly on Instruction Sheet-J03018. 2. Disconnect and discard existing wire harness. 3. See Figure 6. Connect new wire harness (2) to billet headlamp shell (A). 4. Route wire harness (2) through hole in bottom of billet headlamp shell (A) before installing socket housing (4) provided in kit

HARLEY DAVIDSON WIRE LOOM AND HORNS INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 27-02-2012

download
Remove the stock horn and bracket from the stud it is mounted to and unplug the 2 wires. Remove the seat. Route the end of the wire and hose loom without the connectors. Starting in front of the fuel valve, route this loom behind the valve, over the fuel line over the rear cylinder head along the existing wiring or hoses – if your model has any. Follow the frame to where the back bone and seat support rails come together. Route the loom up into the general area where the compressor will mount (i.e. see diagram). Attach the hose to the ‘Y’ connector on the horns themselves. Attach the two black wires from the loom to the relay terminals #87 and #30, located between the air horns behind chrome cover. Attach the wires from the original horn to the remaining terminals #85 and #86 (NOTE: it makes no difference which wire goes to which terminal). Attach the relay to the back of the horn bracket assembly or up under the fuel tank using the small cable tie provided. NOTE: the terminals must point downward to prevent water from entering the relay! Install the horn assembly using the 1/4″ thick chrome washer provided behind the horn mounting bracket. Use the original acorn nut and tighten securely. Check to see that the horns have at least 1/4″ clearance between the engine, shift linkage and choke knob. They should be horizontal or angle down at the front just slightly. Take any slack out of the loom, keeping it up against the frame and away from the engine or exhaust, using several of the small cable ties provided. COMPRESSOR MOUNTING AND WIRING Due to the vast differences in years and models, it is not possible to have one or two brackets that will fit all models. You may need to mount the compressor in a different position or find an alternative location, such as under one of the side covers. On 2001 and newer Tour models there is room in front of the battery to mount it horizontally. On 1997-2000 fuel injected models, under the front portion of the right hand side cover is an excellent location. On most Softtail models you can attach it to the frame tube behind the rear cylinder. On some models such as Sportsters there may not be a place to conceal the compressor; there is a chrome cover and cap available to dress it up for exposed mounting. (RIVCO part no #CMPCR) If mounting the compressor vertically as pictured, try to keep the end with the electrical terminals pointing downward. You can use the long cable ties provided to attach the compressor to the frame or an existing wiring loom. Once the compressor has been mounted securely, route the hose and one of the wires to it and connect the hose to the air outlet barb or fitting. Trim the wire and crimp on one of the female blade terminals and attach to the (+) terminal. Attach the white ground wire supplied to frame close enough to the compressor, so the wire will reach. Trim and crimp another female terminal to it. Attach this wire to the (-) ground terminal. The remaining black wire from the hose/wire loom goes to the battery (+) terminal through the fuse and holder provided. Trim the black wire allowing for the length and placement of the fuse holder. Crimp together and attach to the battery (+) terminal. Turn ignition on and test horns. Check wires and hoses for neat, secure routing and at least 1″ away from exhaust system. Reinstall seat etc.

Incoming search terms:

Harley-Davidson Road King Handlebar Removal and Installation Manual

0

Filed Under (Harley Davidson) by admin on 18-03-2012

download
If the wire length appears to be too short, you will have to lengthen the wires. If that’s the case, I must stress that soldering your wires is far superior to using butt splices. Wiring can be pulled from the splices and the splices themselves will take up a lot of room, making your harness bulky. To extend your wires, ensure the wire segments you are going to splice into the harness are of the same gauge as the original harness. Also, it’s a good idea to cut all of the wire segments now, ahead of time, to the same measured length. This will ensure that once all of the new wire Figure 4. Handlebar harness plug wires as they appear from the back of the plug (where the wires enter the plug from the harness) segments are spliced in, all of the finished wires are of the same length and the pins are lined up. Work from wire to wire, cutting them by staggering the cuts about an inch or so apart (see figure 5). This will prevent a bulge in your harness where all the soldering connections are. After cutting each wire, slide on a two-inch piece of heat shrink tubing before starting your soldering. Remove about ¾” of insulation from the ends of the two wire ends (one wire end being the harness, the other being the segment of new wire being spliced in). Halfway down the length of its exposed section, bend each wire 90 degrees and hook the two wire segments together at the bends. Holding the wires securely with a pair of pliers, twist them in opposite directions around each other. Make sure the ends of the wires are wrapped as tight as possible so their sharp points will not cut through the heat shrink tubing when it’s applied. Apply some soldering flux (a little is all you need) and solder the connection by first applying your soldering iron (or gun) to the wire and then applying the solder to the wire. You should not apply the solder directly to the iron as overheating the solder can lead to poorly made solder joints and improper conduction of electricity. When the connection has cooled, slide your heat shrink tubing over the joint and heat it so that the tubing shrinks, making a nice tight seal.

2002-2005 Honda VFR800/A Wire Harness Replacement Manual

0

Filed Under (Honda) by admin on 21-04-2011

download
If the 18P (light blue) connector is in abnormal condition as shown below, contact TechLine at (800) 421-1900, option 9. FRONT SUB-HARNESS REPLACEMENT 1. Remove the front sub-harness from the cowl stay hooks. Disconnect all the electrical components from the front sub-harness. 2. Temporarily set the main wire harness aside, and disconnect the 6P (natural) con- nector. Then, carefully remove the front sub-harness. 3. Install the new front sub-harness by con- necting the 14P (natural) and 18P (light blue) connectors. NOTE: For routing specifications, refer to the WIRING & HARNESS ROUTING SECTION on pages 7-8. 4. Attach the front sub-harness on the cowl stay hooks. Make sure the front sub-harness is routed elow the main sub-harness. ABNORMAL CONDITION STAY HOOKS 6P (NATURAL) CONNECTOR FRONT UB-HARNESS 14P (NATURAL) CONNECTOR 18P (LIGHT BLUE) CONNECTOR FRONT SUB-HARNESSSTAY HOOK Page 4 VFR800/A #4 4 of 12 NOVEMBER 2007 5. Place the front sub-harness between the radiator and the frame, and below the rec- tifier. Be careful not to damage the front sub-harness or other components. 6. Re-connect the front sub-harness to the 6P (natural) connector. 7. Secure the main wire harness and the front sub-harness using the longer wire band. 8. Secure the main wire harness and the upper side of the front sub-harness using the shorter wire band. Adjust the wire har- ness located within the frame and the radi- ator hose accordingly. 9. Secure the main wire harness fuse box to the front sub-harness using the shorter wire band. FRONT SUB-HARNESS STAY HOOK MAIN-HARNESS FRONT SUB-HARNESS FRONT SUB-HARNESS 6P CONNECTOR (Male) 6P CONNECTOR (Female) WIRE BAND (LONG) WIRE BAND (SHORT)
WIRE BAND (LONG) WIRE BAND (SHORT) MAIN WIRE HARNESS FUSE BO

Incoming search terms:

BMW R1200GS Dual Function LED Running Lights and Flashing Brake Lights installation instructions

0

Filed Under (BMW) by admin on 08-11-2010

download
The flasher is set to flash continuously as long as the brake is applied. To convert to a 5 second flash and then stay solid while the brake is applied, cut the green wire loop on the flasher. Use electrical tape to protect and secure the green wires to the other wires. 2. Remove the rider’s seat. Locate the wire bundle that starts at the rear of the motorcycle. At the most accessible spot carefully remove 3″ to 3½” of protective wire loom. I know, I know…it’s really beautifully done. Cowboy up! Take it off! 3. Mount the flasher in a location that will not crimp wires or interfere with the other bike assemblies. Locate the +12 volt wire ( GRAY wire with BLACK stripe and YELLOW banding) from the brake light Attach the kit RED wire to the brake light positive wire using one of the Posi-Tap connectors in the kit. 4. Locate the Ground wire ( BROWN wire) from the brake light. Attach the kit BLACK wire to the motorcycle ground wire using a Posi-Tap connector. 5. If you have a Fuse Block with ignition switched relay installed, route the Hyper-Lite GRAY wire to a fused circuit on the (relay activated) fuse block . 6. If you do not have a Fuse Block installed, find the alarm circuit connector under the seat . The alarm circuit has a rectangular connector and five wires, White with Black stripe; White with Brown stripe; Red with White; Brown with White; and Green with White stripe. Use a Posi-Tap to attach the Hyper-Lite GRAY wire to the green wire with white stripe. Pull the wire loom back from the wire. Tap into the wire with the Posi-Tap provided. . 7. If using the Hyper-Lite License Plate Mounting bracket, install it now. OR: Clean the side facing reflectors at the rear of the bike with alcohol. Mount the LED modules vertically on the reflectors so that the LEDs point straight back. Press in place for about 5 seconds. The tape can be used only once! If you goof, new tape is required. 8. Route the BLUE and BROWN wires from the flasher and the LED modules. Trim the Blue and Brown wires to remove any excess wire . Use a Posi-Twist to connect the 3 BLUE wires together. Use a Posi-Twist to connect the 3 BROWN wires together. (see Posi-Twist Connector instructions)

Incoming search terms:

HARLEY-DAVIDSON LARGE LED SILVER BULLETS INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 29-01-2011

download
PROCEDURE STEP 1*Remove the stock turn signal fixtures and cut the wires in a convenient and inconspicuous splice location. STEP 2**Place the split lock and flat washers on to the hollow bolts as shown in PIC. 1. Run the power leads through the hollow bolts and assemble the Silver Bullets to their mounts. See PIC. 2. STEP 3*Install the new Silver Bullet assemblies to the Mount Bar on the motorcycle. The stock 10-24 x 1/2″ socket head screws are to be re-used. PROCEDURE fOR AMBER DUAL CIRCUIT (fRONT WIRING) LED SILVER BULLET WIRE COLOR CODING IS AS fOLLOWS: Black — Ground Blue — Running Lights (power) Violet — Turn Signal (power) STEP 1 Turn key on. Test OEM stock front turn signal wiring with test light. STEP 2 Locate and mark the running light (power) wire. STEP 3 Individually activate the turn signals and mark the side-appropriate wires. STEP 4 Use the color code above to solder/connect the corresponding Silver Bullet wires to your Join like colored wires on the Silver Bullets and the bike’s turn signal harnesses. Insulate your connections. Route the wires safely out of harms way and tie the wires in place with nylon cable ties. 1995-EARLIER MODELS With a test light, probe the two black wires leading to each of the stock front turn signals. On each side, the wire that has power only when the turn signal button is depressed is the turn signal positive wire. The wire that is “hot” constantly when the key is on is the running light wire. Connect the violet wire from the Silver Bullet to the bikes turn signal wire, and the blue Silver Bullet wire to the bikes running light wire. Connect the black wire from the Silver Bullet to a known good chassis ground (bare metal). Insulate your connections. Route the wires neatly out of harms way and secure them with nylon cable ties. When replacing stock incandescent turn signals with LED lights, it may be necessary to add a load equalizer to make the turn signals flash properly. NOTE: When using Amber Dual Circuit Silver Bullets in rear applications, blue running lights (power) wire will not be used. To avoid corrosion, tape off bare wire. Test the lights for run and flash functions. If they light, but do not flash in the turn mode, add the load equalizer. The load equalizer has one black and two violet wires. The violet wires are not side specific. NOTE: LED Turn signals require the use of one Load Equalizer PER PAIR OF LED TURN SIGNALS to achieve the proper flash function. It is perfectly normal for the equalizer to get warm (about 140 degrees) during turn signal operation.

DRAG SPECIALTIES MINI SPEEDOMETER WITH LED INDICATOR LIGHTS INSTALLATION INSTRUCTIONS

0

Filed Under (Tips and Review) by admin on 29-01-2011

download
1. Place the motorcycle on a level and secure area. Disconnect the battery. 2. Refer to the appropriate factory service manual and remove the OEM speedometer and indicator lights. The indicator lights usually unplug either in the rear of the headlight or under the gas tank area. 3. Mount the new speedometer in the desired location. 4. Locate the OEM wire for the high beam indicator light. Connect it with the blue wire from the wire harness on the speedometer. Connect the blue/black wire from the speedometer to ground. 5. Locate the OEM wire for the gauge illumination (back) lighting. Connect this wire to the orange wire on the speedometer. Connect the black wire on the speedometer to ground. 6. Locate the OEM wires for the turn signals. Usually they are brown and violet wires. NOTE: You will notice only one bulb for the turn signals in the gauge and two wires from the bike to the harness. If you connect both of these wires directly to the yellow wire on the speedometer, this will allow feedback and cause all the signals to flash at once. To prevent this, you will need to add a diode between each OEM turn signal wire and the yellow wire coming from the speedometer. We recommend that you utilize a Dyna tach adapter, Part #D-101, available separately. This tach adapter includes the diodes necessary to allow the turn signal indicator light to operate correctly. Follow the instructions for the tach adapter, substituting the wires from the original wire harness found in step 6 for the two ignition terminals shown in the wire schematic. Hook the white wire on the tach adapter to the yellow wire for the turn signal indicator on the speedometer. If you use the D-101 adapter, skip steps 7-9 and go directly to step 10. 7. Take one of the diodes, making sure to observe the correct polarity, and attach it to the brown turn signal wire on the bike. 8. Take the remaining diode, again making sure to observe the correct polarity, and attach it to the violet turn signal wire on the bike

Incoming search terms:

Incoming search terms: