966 building material co intl

You search Auto repair manual PDF 966 building material co intl, if there are search results will appear below. If search results do not exist, please search by others keyword.





S&S Connecting Rods Installation Instructions

0

Filed Under (S&S) by admin on 29-10-2010

download
1. Female rod crankpin end to mainshaft nuts – .030″ minimum clearance recommended. A. Install sprocket shaft and crankpin in driveside flywheel. Snug nuts only. Do not torque to final specs. B. Slide connecting rods and bearings over crankpin. C. Rotate rods on crankpin, and observe clearance between rod and sprocket shaft nut. D. If additional clearance is needed, remove material from sprocket shaft nut. Do not remove material from connecting rod. E. Repeat procedure for camside flywheel and pinion shaft. 2. Female rod crankpin end to inner flywheel rim – .060″ clearance recommended. A. While checking female rod to mainshaft clearance, observe clearance between crankpin end of female rod and rim of both flywheels. B. If additional clearance is required, remove material from flywheel at point of contact. Do not remove material from connecting rod. 3. Wristpin end of both female and male rods to flywheel edge -.060″ minimum clearance recommended. A. While checking female rod to mainshaft clearance, observe clearance between wristpin end of both rods and rim of both flywheels. B. If additional clearance is required, remove material from flywheel at point of contact. Do not remove material from connecting rod. 4. Wristpin end to crankcase and cylinder – .060″ is recommended in these areas. A. With the camside flywheel and rods mocked up, install the assembly in the right crankcase half with pistons (less rings) and cylinders in place. B. Rotate flywheel through one full revolution and check for rod to crankcase and cylinder spigot contact on both the front and rear of each cylinder. C. File or grind crankcase or cylinder spigot as needed to achieve .060″ clearance. Do not remove morematerial than needed. D. Repeat for left crankcase half. NOTE: Whenever clearancing is performed in any of these areas, do not remove any material from the connecting rods as clearancing on the rods may unnecessarily weaken them. Make adjustments to the point of contact on the mainshaft nut, flywheel rim, crankcase, cylinder spigot, etc. Connecting rods weakened by clearancing may fail causing serious engine damage.

Incoming search terms:

DMCA

0

Filed Under () by admin on 23-05-2017

Digital Millennium Copyright Act (DMCA) Notice

We are in compliance with 17 U.S.C. $ 512 and the Digital Millennium Copyright Act (“DMCA”). It is our policy to respond to any infringement notices and take appropriate actions under the Digital Millennium Copyright Act C’DMCA”) and other applicable intellectual property laws.

If your copyrighted material has been posted on our website or if hyperlinks to your copyrighted material are returned through our search engine and you want this material removed, you must provide a written communication that details the information listed in the following section. Please be aware that you will be liable for damages (including costs and attorneys’ fees) if you misrepresent information listed on our site that is infringing on your copyrights. We suggest that you first contact an attorney for legal assistance on this matter.

The following elements must be included in your copyright infringement claim:

1. Provide evidence of the authorized person to act on behalf of the owner of an exclusive right that is allegedly infringed.
2. Provide sufficient contact information so that we may contact you. You must also include a valid email address.
3. You must identify in sufficient detail the copyrighted work claimed to have been infringed and including at least one search term under which the material appears in our search results.
4. A statement that the complaining party has a good faith belief that use of the material in the manner complained of is not authorized by the copyright owner, its agent, or the law.
5. A statement that the information in the notification is accurate, and under penalty of perjury, that the complaining party is authorized to act on behalf of the owner of an exclusive right that is allegedly infringed.
6. Must be signed by the authorized person to act on behalf of the owner of an exclusive right that is allegedly being infringed.

Send the infringement notice via contact form with “DMCA Complaint” as your subject line otherwise we won’t be able to process your complaint.

Please allow up to a week for an email response. Note that emailing your complaint to other parties such as our Internet Service Provider will not expedite your request and may result in a delayed response due to the complaint not being filed properly.

Incoming search terms:

GAS VENT INSTALLATION INSTRUCTIONS

0

Filed Under (S&S) by admin on 29-10-2010

download
1. Appliances . Carefully review the appliance manufacturer’s installation instructions for positioning the unit, any special venting or connector requirements, and verify that it is a Category I appliance or an appliance that requires the use of Type B gas vent. 2. Placement . The placement of the vent and fittings must be in accordance with Local Codes, as well as accepted venting practices. If more than one appliance is to be connected to one venting system, the common vent must be correctly sized. It is a good idea to make a sketch of the proposed installation, labelling the components you will need. Adjustable Pipe Lengths are available to make up odd lengths. Minimize the number of turns and lateral runs, as the National Fuel Gas Code places limitations on these. A 45° turn is preferable to a 90° turn. The appliance reference material should be consulted at this time, as well as any Local Authority having jurisdiction. In most localities, building permits are required for any new appliances, or modifications to existing venting systems.
3 3. Figures 1 , 2, & 3 show examples of some typical residential installations . 4. Clearance to Combustibles . A 1-inch clearance (air space) to combustible materials must be maintained , when using Simpson Dura-Vent Round B- Vent, regardless of the pipe diameter. 5. Combustion Air . Refer to appliance installation instructions and local building codes to ensure compliance with required volume of combustion air for each appliance installed . 6. Slope . If the venting system contains lateral (horizontal) components, they shall be positioned so they have an upwards slope away from the appliance of not less than 1/4- inch rise per foot of run. (Horizontal vent installed in attics, unconditioned area, or between floors have further restrictions, please consult your local building codes for specific limitations.)

Honda CB 750 SOHC 8v Performance and Racing Camshafts Installation

0

Filed Under (Honda) by admin on 18-11-2011

download
Upon installation of your WEB-CAM camshaft, check the following. These operations are very important to engine
life, please follow instructions! If your cam is described as a bolt-in in the WEB-CAM catalog, you may skip 1-5
below. Check piston to valve clearance. Provide the necessary clearance by removing material from the piston Minimum .050″ intake, .080″ exhaust.1. Check valve to valve clearance. It may be necessary to remove material from the valves or sink valve seat height in head. 2. Check the valve spring retainer to valve guide clearance at maximum lift. Remove material from the top,of valve guides to provide a minimum of .030″ clearance. 3. Check for valve spring coil bind at maximum valve lift. Clearance at every coil should be at least .015″4. Be certain that cam and/or rocker arms rotate
freely in head or block. Remove material from head,block, or rocker arms where necessary.5. Engine and cam life depend on proper installation. New or reground followers should be used when installing WEB-CAM profiles. Apply the provided
assembly lube to cam lobe and follower surfaces

Harley Davidson 6- SPEED CONVERSION KIT FOR BIG TWIN 5- SPEED TRANSMISSIONS INSTALLATION

0

Filed Under (Harley Davidson) by admin on 05-03-2012

download
5/16 Bolt hole boss clearance This can easily be checked with the trap door gasket. Put the gasket on the dowel pins. AII material of the boss around the hole that “sticks outside” the gasket (60 degrees forward to 60 degree backwards) must be removed (see figure A). Primary fork clearance Place the gasket on the housing and remove material as indicated for clearing the shifter fork (see figure B). WWW . ZODIAC . NL PERFORMANCE PRODUCTS FOR HARLEY-DAVIDSON ® INSTALLATION INSTRUCTIONS FOR 6 SPEED CONVERSION KIT AND 6 SPEED BUILDER KIT speed transmission. Also make sure you have a 1990 or later Factory Service Manual available. Tools The conversion kit should only be used in new or low milage transmissions. If gears or bearings of a used Gear set Removal Refer to the Factory Service Manual Section for Mainshaft and Countershaft removal. When you get to the point of actually sliding the gear set out make sure you properly mark the 5th gear set as described in the Factory Service Manual (for used transmissions only). Further follow the factory removal procedure. Clearance Checks The 6 Speed conversion and builder kit will fit in most OEM or aftermarket transmission housings without may be needed. The following clearances must be checked before assembling the 6 speed transmission. 28-05-2008 We recommend the kits are installed by a qualified mechanic with knowledge of the Harley-Davidson 5 needed are the same as used for a 5 Speed transmission. 5 speed transmission are worn, new ones must be installed, or better, the builder kit should be used. any modification of the housing. However due to casting differences, in some instances some modification
WWW . ZODIAC . NL PERFORMANCE PRODUCTS FOR HARLEY-DAVIDSON ® Pillow block clearance (right side) Make sure there is clearance between the pillow block and the housing. Any clearance is O.K. (see figure C). Fork shaft support clearance Again use the gasket as the template and remove the material as indicated (see figure D). Shift drum end play The end play of the shift drum must be checked prior to final installation. Install the shift drum. Measure the end play with feeler gauges at the right pillow block (see figure E). End play should be between .004″ and .010″, some 1/2″ X 7/8″ 0.008″ thick shims are included to adjust the end play

Incoming search terms:

HARLEY DAVIDSON SOFTAIL BACKREST KIT Installation Instructions

0

Filed Under (Harley Davidson) by admin on 29-01-2011

download
These kits are designed for use on all Softail models equipped with Sissy bar Uprights, part number 52735-85. See Service parts below for kit contents. Installation 1. With your hand, feel through the backrest material to locate mounting holes. 2. Carefully cut holes in material at mounting locations as applicable. Cut only enough material away for screw to enter backrest. 3. See Service Parts Illustration. Secure backrest (4) to sissy bar using bracket (3) and pan head screws (1). 4. Install flat head screw (2) through center hole into backrest (4). 5. Tighten all screws securely. Do not overtighten

2006 KAWASAKI KX250F Service Manual

0

Filed Under (Kawasaki) by admin on 02-12-2010

download
Gasket, Oring Hardening, shrinkage, or damage of both gaskets andO-rings after disassembly can reduce sealing performance. Remove old gaskets and clean the sealing surfaces thoroughly so that no gasket material or other material remains. Install new gaskets and replace used O-ringswhenre-assembling Liquid Gasket, Locking Agent For applications that require Liquid Gasket ora Locking agent, clean the surfaces so that no oil residue remains before applying liquid gasket or locking agent. Do not apply them excessively. Excessive application can clog oil passages and cause serious damage. Press For items such as bearings or oil seals that must be pressed into place, apply small amount of oil to the contact area. Be sure to maintain proper alignment and use smooth movements when installing. GENERAL INFORMATION 1-5 Before Servicing Ball Bearingand Needle Bearing Do not remove pressed ball or needle unless removal is absolutely necessary. Replace with new ones whenever removed. Press bearings with the manufacturer and size marks facing out. Press the bearing into place by putting pressure on the correct bearing race as shown. Pressing the incorrect race can cause pressure between the inner and outer race and result in bearing damage. Oil Seal, Grease Seal Do not remove pressed oil or grease seals unless removal is necessary. Replace with new ones whenever removed. Press new oil seals with manufacture and size marks facing out. Make sure the seal is aligned properly when installing. Apply specified grease to the lip of seal before installing the seal.

YUASA Battery Applications And Specifications

0

Filed Under (Tips and Review) by admin on 13-11-2010

download
Component Features Benefits Cast Grid Special Grid Design Severe vibration resistance & improved conductivity Active Material Proprietary Formulation Reduced shedding, maximum utilization, & long service life Pasted Plates Specified Thickness Ensures vibration resistance through & Weight precise compression & proper service life through specified active material balance Dried-Charged Tank Formed & Properly dried plates in a sealed battery Plates Dried Plates have a virtually limitless shelf-life, while still retaining 70-80% state of charge when initially filled with acid Top Lead Through-Partition Construction, Shorter current path for increased Connections Large Straps electrical conductivity & higher starting currents, heavier parts for maximum durability Case-Cover Thermal Bonded Plastic Air tight seal to prevent air ingress Seal & acid seepage Terminal- Cover Patented Poly-Seal Eliminates acid seepage, reduces Seal Terminal corrosion, & extends battery life Case & Cover Polypropylene Superior resistance to gasoline & oil, impact resistant in extreme weather conditions Additive Sulfate Stop Sulfate stop added to reduce the solubility (Some models) of lead into the acid, which then reduces battery sulfation potenti

Incoming search terms:

Pulsar XR 650R ELECTRIC-START KIT INSTALLATION INSTRUCTIONS

0

Filed Under (Pulsar) by admin on 27-10-2010

download
1. Remove the seat, fuel tank, side panels, muffler, and headers. 2. Disconnect the stator wires from their corresponding mates underneath the seat (trace the wires up from the left side case.) Un-route the stator wiring so it hangs free from the left side case. 3. Remove the stock shift lever and the left side engine case cover. You do not need to drain the oil from the engine. 4. Unbolt and remove the stator and wiring from the stock cover. Do not cut any wires. 5. The stock pulsar coil (small black box hanging from the stator) will have to be modified slightly to clear the ring gear before installation into the new cover. Remove (file or grind) about .030 inches of material from the base of the pulsar coil so that the base is flush with the face of the rest of the coil as shown in Photos 1 and 2. File Here Photo 2 Make flush with this surface Remove material here Photo 1 6. Install the stator and modified pulsar coil into the new engine case cover as shown in Photo 3. Use the three provided Phillips head bolts, split lock-washers, and plastic cable clamps to secure the wiring as shown. You will need to pull about ½” of extra wire through the grommet (Photo 4) to give you enough wire length for the grommet to sit in its case cutout. To do this, remove the electrical tape from the end of the stator wires and pull each wire individually through the grommet. Neither of the stock metal wire guides will be used when reinstalling the stator into the new case (Photo 5). 5/16″ cable clamps 1/8″ cable clamp Photo 3 Photo 5 Not Used Pull extra wire through grommet Photo 4 7. Remove the stock flywheel nut (An air impact tool works best to remove this nut without turning the motor). Remove the flywheel using the flywheel puller provided. 8. Locate the T and F marks on the stock flywheel (Photo 6). The T mark is used to adjust valve clearances and its location needs to be transferred to the ring gear. Scribe a line in the edge of the flywheel in line with the T mark as shown in Photo 7

Air Shammy Model G220/ G220X/ G220XP Owners and Operations Manual

0

Filed Under (Tips and Review) by admin on 24-11-2010

download
NOTE: This step is now performed at Air Shammy. 1. Slip clamp over rubber adapter on blower body. 2. Slip Adapter into the rubber adapter till it bottoms out. 3. Tighten clamp to secure Adapter to blower body. Figure 2 Slip hose over blower adapter Press fit end of hose over the adapter. Fit should be very snug. Figure 3 Slip hose over nozzle. Fit should be snug. On G220XP models, this is where the extension tube can be used. Slide hose over extension tube and slide nozzle into other end of tube. Air Shammy is manufactured by Carelli, LLC. Carelli, LLC warrants this product to be free from defects in material and workmanship for a period of one (1) year from date of purchase. If a product proves to be defective in material or workmanship during the warranty period, Carelli, LLC will, at its sole option repair or replace the product. Warranty is voided if product is used for commercial purposes. Carelli, LLC’s liability is limited to the cost of repair or replacement of the product and shall not be liable for damage to other property caused by defects in the product or any other damages whether incidental, consequential or otherwise.

Incoming search terms:

Incoming search terms: