about timing setting in tata ace

You search Auto repair manual PDF about timing setting in tata ace, if there are search results will appear below. If search results do not exist, please search by others keyword.



  about timing setting in tata ace Direct Download speed 5282 Kb/s

  about timing setting in tata ace Full Version speed 6162 Kb/s



ACE -325X/ 395 X-XX CLOCK, UNIT, WHEEL, ODOMETER, TEMPERATURE & FUEL METER SETTING

0

Filed Under (Honda) by admin on 24-12-2011

download
Setup operations include 12/24hour clock, bar tachometer scale, shift warning RPM, numbers of engine rotation per signal, wheel circumference, units, odometer adjustment, units of temperature, temperature warning and fuel meter input resistance selection. These must be set up step by step. The computer will automatic reversion to main screen if no button operation for 75 seconds at any setting screen. 2. Press both MODE & RESET buttons to go into setting screen. In setting screens, press RESET button to add the flashing digit by 1 or convert units, press MODE button to confirm the digit setting and jump to next digit or next setting screen to be set. Press MODE button for 2 seconds at any setting screen to finish the setting and go to main screen. 3. It displays “12 or 24H and XX:XX-XX” symbols and AM/PM in case you select 12H. Operates buttons as descriptions of item 2 to finish clock and jump to 8,000/16,000rpm scale setting. 4. It displays 8,000rpm scale, presess RESET button to convert 8,000 or 16,000rpm. Press MODE button to confirm the setting and jump to shift RPM warning setting. 5. It displays ” RPM rXXX00 “. Follow the item 2 of button operation to finish the shift RPM warning setting and jump to engine specification setting. 6. It displays “SPC-X.X RPM”, the default value is 1.0; there are 4 options: 1.0, 2.0, 3.0 and 0.5. It means the numbers of engine rotation per signal. For example the value 2.0 means the engine rotate 2 turns to output a signal. 7. Press RESET button to move in loop sequence from one to another value of the 4 values. Press MODE button to confirm the setting and go to wheel circumference setting screen. 8. In “cXXXX” display, “c” means “Circumference”, following 4 default digits; flashing digit is digit to be set. Follow the item 2 of button operation to finish the wheel circumference setting and jump to unit setting. 9. It displays KM/h or MPH, each press of RESET button converts unit; press MODE button to confirm unit setting and jump to odometer setting. 10. It displays “ODO & 00000Xkm”, the “X” is tested odometer in factory, follow item 2 to setting a desired odometer and jump to thermometer unit setting. The setting screen will disappear when the odometer is over 30km or your setting is over 30km and returned to main screen. 11. It displaysm ” , or oFF”, each press of RESET button converts , or oFF; press MODE button to confirm temperature setting and jump to temperature warning setting. 12. It displays ” XXX” and the selected unit. Follow the item 2 of button operation to finish the temperature warning setting and go to fuel sensor input resistance setting. 13. It displays “100r and fuel tank symbol”, follow the item 2 to select 100, 250, 510 Ohm or oFF and return to the main screen. The fuel meter bar will disappear if you select oFF mode.

Incoming search terms:

ULTIMA IGNITION MODULE AND KIT INSTALLATION MANUAL FOR HARLEY DAVIDSON

0

Filed Under (Harley Davidson) by admin on 03-03-2011

download
Disconnect battery. 2. Mark location of timing plate in relation to inside of cam cover. This will give a starting point for timing on new module. Remove old ignition if applicable (see manual) Clymer, Haynes. 3. If your bike is not equipped with timing rotor M/W# 53-528 OEM#32402-83 you must buy one (included in kit). Also a single fire coil is needed (included in kit) M/W# 53-632. Any single fire coil rated 2-4 ohms can be used. NO SOLID CORE PLUG WIRES (copper, silver) they will damage the unit. 4. Install module: helpful hints, early model nose cones, i.e. Shovel Heads, the hole for the wire may need to be drilled out. Align with previously scripted mark for timing. Use lockwashers for stand offs for correct clearance of cover plate. Run wire loom. 5. Connect wires, see wiring diagram. Tape unused wires, green or brown. 12v to tach (brown) will damage module. Set timing. 1996 and later should not be timed 20˚ BTDC as the OEM module, but at 35˚ BTDC. Use this mark when using timing light. If VOESswitch is not used you must ground VOES wire (green) while timing. Refer to manual for correct identification of timing marks. At start up and timing, set spark advance in middle position. FUNCTION SWITCHES LED timing indicator light: When out, shows TDC. When ignition is on, LED will light up. When engine is cranking LED will blink. Electric Start/Kickstart: Set accordingly. VOES/Race mode: VOES switch lets the motor run smoother and improves gas mileage. If you don’t use it or add one tape up green wire and switch to race. VOES switch to use, M/W# 53-652. Spark advance: High compression motors should use race mode and 93 octane or better gas. Changing from VOES to race changes advance curves. Agood rule of thumb is if the engine knocks when throttle is applied in high gear, turn back spark advance curve until it stops engine knock. RPMlimiter: Set at desired RPM to cut engine power. Rear Cylinder: This is for racing and should be set at a dyno. +/-5˚. Rear cylinder timing is achieved through this adjuster. Most should dial to middle setting and leave alone. After all switches are set, install cover with supplied gasket and feel the increased performance of a solid state single fire ignition. Again, we remind you, if you don’t feel confident about installing this unit, let a qualified mechanic do it and be assured you are getting the best performance and gas mileage possible.

Incoming search terms:

YAMAHA XS650H/ SH Supplementary Service Manual

0

Filed Under (Yamaha) by admin on 21-11-2010

download
Ignition timing check 1. Ignition timing is checked with a timing light by observing the position of the rotor pointer and the marks stamped on the timing plate. The timing plate is marked as follows. “ll” Firing range for No. 1 (L.H.) “T” Top Dead Center for No. 1, fL.H.1 cylinder 2. Connect the timing light to the left cylinder spark plug lead wire. 3. Start the engine and keep the engine speed as specified. Use a tachometer to check the engine speed. B. PICK-UP COIL ASSEMBLY The method of mounting the pick-up coil assembly is changed for easier service work. Thus, the followings “Pick-up coil assembly removal” and “Pick-up coil assembly reinstallation” should be changed. Pick-up coil assembly removal Remove the pick-up coil securing screws and remove the pick-up coil assembly. Pick-up coil assembly reinstallation Install the pick-up coil assembly on to the stator assembly. _ L 4. Specified engine speed: 1,200 r/min The rotor pointer should be within the limits of ” fl ” on the timing plate. If it exceeds the limits or does not steady, check the timing plate for tight- ness and/or ignition system for damage. NOTE: Ignition timing is not adjustable. C. FUEL LEVEL The carburetor is furnished with a drain screw to provide easy access to service work. Thus, the following “Fuel level measurement” should be added. Fuel level measurement NOTE: Before checking the fuel level, note the follow- ing: 1. Place the motorcycle on a level surface. 2. Adjust the motorcycle position by placing a suitable stand or a garage jack under the engine so that the carburetor is positioned vertically. 1. 2. Connect the level gauge (special tool) or a vinyl pipe of 6 mm (0.24 in) in inside diameter to the float bowl nozzle left or right side carburetor. Set the gauge as shown and loosen the drain screw 3. Start the engine and stop it after a few minutes of run. This procedure is neces- sary to obtain the correct fuel level. NOTE: Make sure the fuel petcock is “ON” or “RES” oosition. 4. Note the fuel level and bring the gauge to the other end of the carburetor line and repeat step 3 above. Note the fuel level again and compare it with the previous gauge reading. They should be equal. If not, place a suitable size of wooden piece or the. alike under the center stand and adjust. 5. Check the fuel level one by one. The level should be in the specified range.

Incoming search terms:

Harley-Davidson Electronic Ignition Module Installation instructions

0

Filed Under (Harley Davidson) by admin on 23-04-2012

download
Step 1: Switch main dashboard switch to “off” position (Ignition& light switch) Step 2: Disconnect negative (ground) cable from the Battery Step 3: Remove the Condenser and Breaker points from the circuit breaker timing base. Step 4: Disconnect advance/ retard cable from timing base Step 5: Remove timing base from timer shaft and housing (see your manual for instructions) Step 6: Remove circuit breaker wire stud or circuit breaker to coil wire assembly from timing base Step 7: Remove circuit breaker wire from Ignition coil, and mark terminal on coil with piece of tape. Step 8: Install the Electronic Ignition Module on the timing base. Mount this short black wire to one on the timer base screws by keeping some slack in this wire so the timing base can turn free. Solder the flag terminal to this short black wire and mount it under the timer to motor bolt. This way of mounting provides a much better grounding. Do NOT use the screws (number 1 or 2 screws from picture below) from the timing base!!!! Step 9: Now three wires pass this hole via the rubber grommet. Figure 1 Figure 2 Step 10: Reinstall the timer base on the timer shaft housing, and keep some slack in the wires before protruding the hole in the timer shaft housing, and secure with ground spring and cover retainer. Reconnect the advance/retard cable to the timer base. Step 11: Route the two long wires to the ignition coil. Check in the HD service manual for a proper route to the ignition coil. (Keep away from hot surfaces like exhaust systems). Cut the wires to the exact length necessary for mounting. Step 12: Determine the exact length of the wire loom. Keep in mind that one end of the loom enters the timer shaft housing by 1cm. Cut the loom to the proper length. Step 13: Insert both wires in the loom. Strip both wire ends and solder the two flag terminals on the wires. Step 14: Connect the red wire to the ignition coil, on the terminal where the 6 or 12 volt is supplied to. This terminal has at minimum one wire connected which runs to the main switch. Step 15: Connect the black wire to the ignition coil on the terminal which is empty, and has piece of tape on it. (Old place where the circuit breaker wire was connected to) Step 16: Install the trigger rotor on the timer shaft cam, and tighten the hex screw by using the hex key tool. Do not over tighten the screw! Step 17: Check for clearance between trigger rotor and Electronic Ignition Module. Appropriate clearance is between 0,5mm and 1,5mm . Minor adjustments can be made by unlocking the two screws and slightly shift/move the Electronic Ignition Module. Check if the rotor moves free. Timing instructions: Remove the spark plugs from the engine, but keep them connected to the spark coil cables and engine ground. This enables normal operation of the spark, and prevents unwanted engine firing on compression stroke. See service manual or handbook for timing instructions of your model Step 18: Reconnect the negative (ground) cable to the battery. Step 19: Switch main power to “on” position. The red light in the Electronic Ignition Module might already light up. If not, turn the kick starter slowly. The red light is on while charging (closed points)the Ignition coil, facing solid metal of the trigger rotor. The light goes off (open points) when the end of the solid surface of the trigger rotor passes the centre of the Electronic Ignition Module. At that point a spark is generated by the coil

Incoming search terms:

The Honda Ace/ Spirit 750 Lowering Kit from INSTATALLATION

0

Filed Under (Honda) by admin on 16-11-2011

download
The installation of the Scootworks Ace/Spirit Lowering Kit follows the same procedure as replacing the rear shocks. However, Scootworks wanted to assist you as much as possible with the installation process, and developed this instruction package. If there are any steps you feel need improvement in instructions, please email support@scootworks.com and specify the area you are having trouble with. Unpacking! The shipping container and contents must be inspected by the purchaser for damage to goods immediately upon receipt of goods, and a claim must be filed with the carrier if damage is discovered. The purchaser must contact Scootworks within 24 hours from receipt of damaged goods to file a claim, and for further instructions. Your Scootworks Ace/Spirit Lowering Kit will come packed with a left and right side lowering assembly, two large flat washers, two M8 x 1.25 hex head bolts, and these printed instructions

KTM 60 SX / 65 SX REPAIR MANUAL ENGINE

0

Filed Under (KTM) by admin on 12-11-2010

download
Carburetor adjustment Basic information about the original carburetor setting The original carburetor setting was adapted for an altitude of approx. 500 meters (1600 ft.) above sea level, and the ambient temperature of approx. 20°C (68°F), mainly for off-road use and central European premium-grade fuel (ROZ 95). Mixing ratio 2-stroke motor oil : super fuel 1:40 . Basic information of changing the carburetor setting Always start out from the original carburetor setting. Essential requirements are a clean air filter system, air-tight exhaust system and an intact carburetor. Experience has shown that adjusting the main jet, the idling jet and the jet needle is sufficient and that changes of other parts of the carburetor will not greatly affect engine performance. RULE OF THUMB: high altitude or high temperatures  choose leaner carburetor adjustment low altitude or low temperatures  choose richer carburetor adjustment * WARNING * -ONLYUSE PREMIUM – GRADE GASOLINE ROZ 95 MIXED WITH HIGH – GRADE TWO – STROKE ENGINE OIL . OTHER TYPES OF GASOLINE CAN CAUSE ENGINE FAILURE , AND USE OF SAME WILL VOID YOUR WARRANTY . -ONLYUSE HIGH – GRADE 2- STROKE ENGINE OIL OF KNOWN BRANDS ( I . E .SHELL ADVANCE RACING X). -NOTENOUGH OIL OR LOW – GRADE OILCAN CAUSE EROSION OF THE PISTON . USING TOO MUCH OIL , THE ENGINE CAN START SMOKING AND FOUL THE SPARKPLUG . -INTHE CASE OFA LEANER ADJUSTMENT OF THE CARBURETOR PROCEED CAUTIOUSLY . ALWAYSREDUCETHEJETSIZEINSTEPSOFONENUMBERTOAVOID OVERHEATING AND PISTON SEIZURE . NOTE: If despite a changed adjustment the engine does not run properly, look for mechanical faults and check the ignition system. Basic information on carburetor wear As a result of engine vibrations, throttle valve, jet needle, and needle jet are subjected to increased wear. This wear may cause carburetor malfunction (e.g., overly rich mixture). Therefore, these parts should be replaced after 1000 hours of using. Idling range – A Operation with closed throttle valve. This range is influenced by the idle adjusting screw 1 . Only make adjustments when the engine is hot. The idling speed can be changed by turning the idle adjusting screw. Turning it clockwise produces a higher idling speed and turning the screw counterclockwise produces a lower idling speed. Opening up – B Engine behavior when the throttle opens. The idle jet and the shape of the throttle valve influences this range. If, despite good idling-speed and part-throttle setting, the engine sputters and smokes when the throttle is fully opened and develops its full power not smoothly but suddenly at high engine speeds, the mixture to the carburetor will be too rich, the fuel level too high or the float needle is leaking. Part-throttle range – C Operation with partly open throttle valve. This range is only influenced by the jet needle (shape and position). The optimum part-throttle setting is controlled by the idling setting in the lower range and by the main jet in the upper range. If the engine runs on a four-stroke cycle or with reduced power when it is accelerated with the throttle partly open, the jet needle must be lowered by one notch. If then the engine pings, especially when accelerating under full power at maximum engine revs, the jet needle should be raised. If these faults should occur at the lower end of the part throttle range at a four-stroke running, make the idling range leaner; if the engine pings, adjust the idling range richer

Incoming search terms:

CL-1000 CONDOR CYCLE LOADER USER INSTRUCTION MANUAL

0

Filed Under (Tips and Review) by admin on 25-11-2010

download
Confirm that the cradle is set in the optimized position setting (See RECOMMENDED CRADLE SETTINGS) for the entering tire and wheel. Adjustment of cradle is crucial for optimum retention. Optimum retention is achieved by trying different settings. ( REFER TO CAUTION PARAGRAPH BELOW ): If the optimum vertical support is achieved, the motorcycle will hold itself upright. If optimum retention is not achieved try different cradle settings. ( REFER TO CAUTION PARAGRAPH BELOW ). Once cradle is positioned, tighten the brakes using the eye bolts and place the Cycle Loader in front of the motorcycle. Push or drive the motorcycle, centered into unit, until the cradle of the Cycle Loader has fully engaged the wheel. Once the wheel is cradled, proceed to push further into the Cycle Loader until the wheel has engaged the front stop. If the optimum vertical support is achieved, the motorcycle will hold itself upright. As an extra precaution, an optional Velcro strap may be used to strap the cradled wheel to the front stop (Optional Velcro strap purchased separately). Always strap Velcro through the wheel and around the front stop below the upper front stop flange. Loosen the brakes and use two (2) tie-down straps to secure the motorcycle to the two front eyebolts of the Cycle Loader. Hook wench to Ω” ‘U’ hook in front of Cycle Loader. Use the wench to pull the Cycle Loader with motorcycle up the flat bed. Once the motorcycle is all the way on the flat bed, the bike should be secured to the flat bed itself. For more information on use, refer to www.condor- lift.com. RECOMMEDED CRADLE SETTINGS: The Condor® Cycle Loader is designed so that for every tire/wheel size within the ranges specified a minimum of 2 cradle settings is suitable. **The optimum cradle setting for a specific tire would be, the setting that allows the cradle to tilt flush with the unit/ or º” below the opening in the main unit where the cradle sits, without touching.** The 2nd optimum setting would be the setting forward from the optimum setting away from the entry direction. If less retention is desired at any time due to too much retention or sticking, the cradle may be moved away from the entry direction one notch. RACING APPLICATIONS: For bikes with GP or low durometer front tires compounds, use the 5th cradle setting from the entry directions. CAUTION: Always make sure that all fasteners are tight and all pins are in place prior to use. Understand the limitations of this product and do not exceed these limitations. Always make sure that the unit’s cradle settings are optimum for the tire size of the motorcycle before use. For bikes with very low fenders and or cowlings, a custom cradle may be purchased fitted to specific tire sizes, so as not to make contact. For standard sport bike front wheel combinations, the 1, 2, 3, front settings may be suitable. If instructions are not clear, additional information is available at www.condor-lift. com or call 1-800-461-1344. Technical Components Development & Design is not responsible for any damage incurred by exceeding this product’s limitations in structure and/or functionality.

KTM 250/ 300/ 380 SX,MXC,EXC ENGINE REPAIR MANUAL

0

Filed Under (KTM) by admin on 12-11-2010

download
Repair manual KTM 250 / 300 / 380 Art No 3206004 -E 2-2C main jet jet needle jet needle air control screw idle adjusting screw idle jet throttle valve Idling range A Operation with closed throttle valve. This range is influenced by the position of the air control screw 1 and the idle adjusting screw 2 . Only make adjustments when the engine is hot. To this end, slightly increase the idling speed of the engine by means of the idle adjusting screw. Turning it clockwise produces a higher idling speed and turning the screw counterclockwise produces a lower idling speed. Create a round and stable engine speed using the air control screw (basic position of the air control screw = open by 1.5 turns). Then adjust to the normal idling speed by means of the idle adjusting screw. Opening up B Engine behavior when the throttle opens. The idle jet and the shape of the throttle valve influences this range. If, despite good idling-speed and part-throttle setting, the engine sputters and smokes when the throttle is fully opened and develops its full power not smoothly but suddenly at high engine speeds, the mixture to the carburetor will be too rich, the fuel level too high or the float needle is leaking. Part-throttle range C Operation with partly open throttle valve. This range is only influenced by the jet needle (shape and position). The optimum part-throttle setting is controlled by the idling setting in the lower range and by the main jet in the upper range. If the engine runs on a four-stroke cycle or with reduced power when it is accelerated with the throttle partly open, the jet needle must be lowered by one notch. If then the engine pings, especially when accelerating under full power at maximum engine revs, the jet needle should be raised. If these faults should occur at the lower end of the part throttle range at a four-stroke running, make the idling range leaner; if the engine pings, adjust the idling range richer. Full throttle range D Operation with the throttle fully open (flat out). This range is influenced by the main jet and the jet needle. If the porcelain of the new spark plug is found to have a very bright or white coating or if the engine rings, after a short distance of riding flat out, a larger main jet is required. If the porcelain is dark brown or black with soot the main jet must be replaced by a smaller one. mixture too rich: too much fuel in proportion to air mixture too lean: not enough fuel in proportion to air 1 2 OPERATING RANGES OF THE CARBURETOR 2-3C Carburetor adjustment Basic information on the original carburetor setting The original carburetor setting was adapted for an altitude of approx. 500 meters (1600 ft.) above sea level, and the ambient temperature of approx. 20°C (68°F), mainly for off-road use and central European premium-grade fuel (ROZ 95 MOZ). Mixing ratio 2-stroke motor oil : super fuel 1:40 – 1:60. Basic information on a change of the carburetor setting Always start out from the original carburetor setting. Essential requirements are a clean air filter system, air-tight exhaust system and an intact carburetor. Experience has shown that adjusting the main jet, the idling jet and the jet needle is sufficient and that changes of other parts of the carburetor will not greatly affect engine performance. RULE OF THUMB:

Incoming search terms:

2003 Ducati ST4s Timing Belt Adjustment

0

Filed Under (Aprilia) by admin on 31-10-2010

download
This instruction on cam belt adjustment starts after you remove the fairing pieces. Plan on an hour to remove these. Since you are performing your own service, buying Ducati belts may not be that expensive. There may be another belt source, but I have not confirmed this for the 996 engine of the 02-03 ST4s. Fig 1 – ST4s ready for belt adj./ repl. Fig 2 – Crank tool installed. See dwg. 1) Ensure maximum of ½ tank of gas. Fuel will leak into the charcoal canister, then onto the floor if the tank is over half full and the tank is tilted up on its hinge. So put the tank up on its hinge. 2) Remove spark plugs. Cover sparkplug wells with boots or rags. This is a great time to toss out those Champions for a set of NGK DCPR8E’s. 3) Remove the front shield from the horizontal cylinder head. 4) Remove crankshaft cover on Riders LH side and insert crank tool. A crank tool can be made by following the drawing at the end of this document. See Fig 2 above. The flat head screws used are kind of soft so beware on their removal. 5) Remove oil pressure sending unit cable and remove oil sending unit. No oil should pour out. 6) Remove battery and remove bolts fastening battery box to engine/frame. You can let the battery box dangle or partially support it via a bungee cord. Be careful of the cable on the ground of the ECU. By dangling the battery box excess stress could be placed on this cables connector and you don’t want to troubleshoot an intermittent electrical issue. 7) Remove cam belt covers. The two covers over the cams are real easy. The center piece is removed by pulling it down. You may have to move some hoses and cables out Timing belt adj. doc 1
of the way because it is a tight fit. Removing the oil pressure sending unit gave clearance for the removal. Fig 1 shows bike ready to be worked on. On the Rider’s LH is a window on the case cover. Using a flashlight to illuminate the area, marks can be rotated into view using the engine turning tool. There are two marks denoting the TDC of each of the cylinders. When a mark in the window aligns with the pointer, look at the crank driving pulley on the Rider’s RH of the engine. If the driving pulley’s mark is aligned with the pointer on the engine case, you are at TDC horizontal cylinder. If the pulley mark and the pointer on the engine do not align, rotate the engine until the mark in the window on the Rider’s LH side case cover aligns as well as the pulley’s mark and the engine’s pointer. Fig 3 shows the engine pulley and pointer. You can check that the horizontal piston is at TDC by inserting a welding rod into the spark plug well and touch the top of the piston with it to sense its position. Timing marks on cam pulleys are clearly stamped on all four pulleys. When the crank driving pulley aligns with its corresponding pointer on the engine case and the marks on the pulleys align with their corresponding marks on both cylinders, you are in position for belt adjustment and replacement

Incoming search terms:

2003 – 2007 4Runner OIL LEAK FROM FRONT TIMING COVER

0

Filed Under (Toyota Manuals) by admin on 31-10-2011

download
evidence of a small oil leak located where the Bank 1 cylinder head, engine block, and timing cover meet. Use the following repair procedure to address this condition. 2003 – 2007 model year 4Runner vehicles equipped with the 1GR-FE engine and produced BEFORE the Production Change Effective VINs shown below. MODEL PLANT DRIVETRAIN PRODUCTION CHANGE EFFECTIVE VIN 2WD JTEZU17R#68064608 Hino 2WD JTEZU14R#78076191 4Runner Hino 4WD JTEBU14R#78078323 4Runner 4WD JTEBU14R#78090468 Tahara 2WD JTEZU14R#70091230 Tahara 4WD JTEBU14R#70117349 OP CODE DESCRIPTION TIME OFP T1 T2 EG7036 Reseal FrontTiming Cover with FIPG 2WD7.6 113100P0306548 EG7036 Reseal Front Timing Cover with FIPG 4WD8.5 11310-0P030 65 48 Applicable Warranty*: This repair is covered under the Toyota Powertrain Warranty. This warranty is in effect for 60 months or 60,000 miles, whichever occurs first, from the vehicle’s in-service date. *Warranty application is limited to correction of a problem based upon a customer’s specific complaint

Incoming search terms:

Incoming search terms: