adjust shift lever on breakout

You search Auto repair manual PDF adjust shift lever on breakout, if there are search results will appear below. If search results do not exist, please search by others keyword.



  adjust shift lever on breakout Direct Download speed 5282 Kb/s

  adjust shift lever on breakout Full Version speed 6162 Kb/s



2007 Ural Models Gear Up Patrol Tourist Installation Manual

0

Filed Under (Ural) by admin on 02-11-2010

download
Font Brake Control Lever Clutch control lever: When the clutch lever is squeezed, the engine is disengaged from the gearbox. When the lever is released, the engine and gearbox are engaged. WARNING: MAKE SURE FINGERS ARE NOT POSITIONED BETWEEN HAND CONTROL LEVERS AND HANDLEBAR GRIPS OR OPERATION OF VEHICLE COULD BE IMPAIRED . WARNING: B EFORE STARTING ENGINE , ALWAYS SHIFT TRANSMISSION TO NEUTRAL TO PREVENT ACCIDENTAL MOVEMENT WHICH COULD CAUSE POSSIBLE DAMAGE TO MOTORCYCLE AND PERSONAL INJURY . Caution: Always engage the clutch release lever when shifting. Serious internal damage may result to the transmission if the clutch release lever is not engaged. Front brake control lever: When the lever is squeezed, the front wheel brake is actuated. The front brake should be used together with rear brake. When the brake lever is squeezed, the stop signal lights are switched on. 19 Kickstart lever : Designed to start the engine. Upon kicking the lever the crankshaft is actuated through the gearbox. The lever is returned to its initial position by the spring inside the gearbox. Gear shift lever: This is a heal shift type of lever. To shift up from a low gear to a high gear the rear arm(heal shift) is pressed. To shift down from a high gear to a low gear the from arm is depressed. Since the heel-toe shift lever is short-coupled, it is much easier to shift up using the heal shift, and to shift down using the toe shift with the ball of your foot. The neutral gear is between the 1st and 2nd gears. It is important to shift smoothly with a constant force, and not to kick the gear shift pedal. Serious damage may result to the shifting mechanism if the gear shift pedal is kicked, rather than pressed. NOTE: The neutral lamp will illuminate when the transmission is in neutral. (see “Starting the Engine”). Gear Shift Foot Pedal Kick Lever 20 Parking Brake Sidecar Drive Lever Rear Brake Pedal Parking Brake: Used to hold the bike when parked. To engage, press the rear brake pedal, push down and twist the parking brake lever counter clockwise. Sidecar drive engagement lever: Used to engage the drive axle to the sidecar wheel on the Patrol and Gear Up model motorcycles. WARNING: Never engage sidecar drive on concrete or hard surface. Severe damage to drivetrain will result if the sidecar drive is engaged on pavement. Rear brake lever: Actuates the rear brakes on both the motorcycle and sidecar. WARNING: DO NOT APPLY EITHER BRAKE STRONGLY ENOUGH TO LOCK THE WHEELS BECAUSE THIS MAY CAUSE POSSIBLE LOSS OF CONTROL OF THE MOTORCYCLE . ALWAYS USE BOTH BRAKES . NEVER STOP WITH FRONT OR REAR BRAKE ONLY . WARNING: AN IMPROPERLY ADJUSTED REAR BRAKE PEDAL COULD INTERFERE WITH PROPER REAR BRAKE OPERATION RESULTING IN POOR BRAKE ACTION

Incoming search terms:

HARLEY DAVIDSON CUSTOM HAND LEVER KIT BRAKE LEVER INSTALLATION

0

Filed Under (Harley Davidson) by admin on 29-01-2011

download
1. See Figure 1. Squeeze the brake lever and place the cardboard insert between the brake lever and lever bracket. NOTE Use the eyelet of an ordinary cable strap if the cardboard insert is not available. NOTE Do not remove the handlebar clamp or switch housing assembly to remove the brake lever. Wear safety glasses or goggles when removing or installing retaining rings. Retaining rings can slip from the pliers and could be propelled with enough force to cause serious eye injury. (00312a) 2. See the Figure 2 and the FRONT BRAKE MASTER CYLINDER section of the Service Manual. Remove the retaining ring (B) from the groove in the pivot pin (C). Inspect the retaining ring (part number 11143) and replace if needed. 3. Remove the pivot pin and retain for re-use. Remove and discard the original equipment brake lever and pivot lever bushing. 4. Insert the pivot lever bushing (2) from the kit into the new brake lever (1). NOTE Follow the instructions in Steps 4 and 5 carefully in order to prevent the actuating tab on the brake lever from damaging the rubber boot and plunger of the front stoplight switch. -J04165 1 of 3
5. Gently press and hold the piston cap (A) forward with a screwdriver. Slip the brake lever into position and align the pivot pin holes. 6. Install the pivot pin and retaining ring removed in Steps 1 and 2. 7. Check the front brake for proper operation. There should be no free play in the hand lever. A slight preload is per- missible. A plugged or covered relief port can cause brake drag or lock-up, which could lead to loss of control, resulting in death or serious injury. (00288a) 8. To verify proper operation of the master-cylinder relief port, actuate the brake lever with the reservoir cover and gasket removed. A slight spurt of fluid will break the surface if internal components are working properly. 9. Reinstall the master cylinder cover. Be sure that all lights and switches operate properly before operating motorcycle. Low visibility of rider can result in death or serious injury. (00316a) 10. Check that the stop light goes on when the brake lever is actuated. CLUTCH LEVER INSTALLATION See the CLUTCH CONTROL section of the appropriate Service Manual for all clutch lever removal, installation and adjustment procedures.

HARLEY DAVIDSON HAND LEVER KITS INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 18-02-2011

download
BRAKE LEVER INSTALLATION Do not remove or install the master cylinder assembly without first positioning a 5/32-inch (4 mm) thick insert between the brake lever and lever bracket. Removing or installing the master cylinder assembly without the insert in place may result in damage to the rubber boot and plunger on the front stoplight switch. (00324a) is 01010 Figure 1. 5/32 in. (4 mm) Cardboard Insert 1. See Figure 1. Squeeze the brake lever and place the cardboard insert between the brake lever and lever bracket. NOTE Use the eyelet of an ordinary cable strap if the cardboard insert is not available. NOTE Do not remove the handlebar clamp or switch housing assembly to remove the brake lever. Wear safety glasses or goggles when removing or installing retaining rings. Retaining rings can slip from the pliers and could be propelled with enough force to cause serious eye injury. (00312a) 2. See the Figure 2 and the FRONT BRAKE MASTER CYLINDER section of the Service Manual. Remove the retaining ring (4) from the groove in the pivot pin (B) and discard retaining ring. 3. Remove the pivot pin and retain for re-use. Remove and discard the original equipment brake lever and pivot lever bushing. NOTE New brake levers come with the pivot lever bushing installed. NOTE Follow the instructions in Steps 3 and 4 carefully in order to prevent the actuating tab on the brake lever from damaging the rubber boot and plunger of the front stoplight switch. -J04342 1 of 3 4. Gently press and hold the piston cap (A) forward with a screwdriver. Slip the brake lever into position and align the pivot pin holes. 5. Install the pivot pin removed in Step 2 and new retaining ring (4) from kit. 6. Check the front brake for proper operation. There should be no free play in the hand lever. A slight preload is per- missible. A plugged or covered relief port can cause brake drag or lock-up, which could lead to loss of control, resulting in death or serious injury. (00288a) 7. To verify proper operation of the master-cylinder relief port, actuate the brake lever with the reservoir cover and gasket removed. A slight spurt of fluid will break the surface if internal components are working properly. 8. Reinstall the master cylinder cover. Be sure that all lights and switches operate properly before operating motorcycle. Low visibility of rider can result in death or serious injury. (00316a) 9. Check that the stop light goes on when the brake lever is actuated. CLUTCH LEVER INSTALLATION See the CLUTCH CONTROL section of the appropriate Service Manual for all clutch lever removal, installation and adjustment procedures. SERVICE PARTS

HARLEY DAVIDSON HEEL/TOE SHIFT LEVER KITS INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 18-03-2011

download
INSTALLATION NOTE The shift levers in these kits have opposite counterbored screw holes. When the toe and heel levers are positioned correctly, the socket head cap screws will be installed from the bottom of both levers. 1. Before removing the original shift levers, note the orientation. You may want to replace them at the same position and angle. NOTE The original equipment shift levers may have the socket head screws that secure the shift levers to the splined shifter shaft installed from the top or bottom, depending on your model motorcycle. 2. See Figure 1. Remove the original equipment shifter pegs (A) and retain for re-attachment to the new levers if desired. Remove the socket head screws (3) that clamp the shift levers onto the splined shifter shaft. Remove the original equipment shift levers. 3. First, position the toe shifter lever (1) so the counterbored screw hole is at the bottom. Slide the toe shifter lever onto the splined shifter shaft and position to the desired angle, aligning the screw hole with the notch on the shaft. 4. Install the heel shift lever (2) with the counterbore at the bottom. 5. Add a few drops of Loctite® 243 (blue) to the socket head screws (3), and insert the screws into the counterbored holes. Tighten to 24-26 ft-lbs (32-35 Nm) . 6. Install the shifter pegs onto the new shift levers. If using the original pegs, place a few drops of Loctite blue onto the screw threads prior to installation. Tighten the shifter peg screws. 7. Check for proper operation and clearance

HARLEY DAVIDSON DYNA FLOORBOARD KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 23-03-2011

download
Installation SHIFTER ASSEMBLY (LEFT SIDE) 1. Remove highway footrest assembly, if equipped. Discard bracket, plate and mounting hardware. 2. Remove stock footrest assembly. 3. Remove stock (chrome) shift lever. Retain shift lever, peg, bolt and washer. 1 WARNING ® 1 of 5 Kit Number 50601-01 -J01921 2 of 5 Figure 1. Shifter Assembly (Left Side) Item Description Part No. 1 Bolt, 5/16-18 x 5/8 hex HD 2882W 2 Hex cap screw, 5/16-18 x 2.00 (2) 3023 4 Set screw, shaft cover 3231B 6 Assembly,shift lever 33704-01A 7 Assembly,adjustable shifter rod 33719-79B 8 Lever, shifter, machining, polish 33706-01 9 Assembly, shifter plate, polish 33700-01 10 Cover, shifter lever, rubber (2) 34619-85 11 Retainer,shift lever for 1996 to 2000 models 34639-93 Item Description Part No. 11ARetainer bracket, shift lever for 2001 and later models 34639-01 12 Cover, shifter shaft 34640-93 13 Washer, wave, overlap type (2) 34641-01 17 Socket head cap screw 4740A 25 Washer, 5/16″ (2) 6016 28 Washer. 5/16″ 6702 30 Nut, hex, locking, 5/16-18 7710W 32 Acorn nut, 5/16-24 7736 33 Hex jam nut, 5/16-24 7744 30 11 1 12 7 32 28 6 13 9 25 2 17 25 2 10 8 i03110.eps 33 4 11A ’96-2000 models 2001 and later models 4. See Figure 1. 1996 to 2000 models. Bolt shifter lever shaft retainer bracket (11) to the stock shifter lever with bolt (1) and nut (30). Do not tighten bolt at this time. 2001 and later models. Bolt shifter lever shaft retainer bracket (11A) to the stock shifter lever with bolt (1) and nut (30). Do not tighten bolt at this time. 5. Loosen the left rear crankcase bolt (at bottom of cylinder) and slide the slotted end of shifter lever shaft retainer bracket (11) onto the bolt, but beneath the washer. Tighten crankcase stud to 15-17 ft-lbs (20-23 Nm). 6. Place chrome cover (12) on shifter lever shaft (at primary case) and secure with set screw (5). NOTE Small wave washer (13) goes between foot shifter and bracket. 7. See Figure 1. Place small wave washer (13) on shifter lever (6) shaft. Coat shaft with Loctite Anti-seize and slide into bracket. 8. Install foot shift bracket (9) using screws (2). Tighten screws to 25-30 ft-lbs (34-41 Nm). 9. Place shifter rod (2) and washers (25) in position. Use short stud on shifter rod to secure shifter rod at the transmission end. Use Loctite 242 (blue) on stud before installing. 10. Install acorn nut (32) and washer (28) at foot shift end. Use Loctite 242 (blue) on acorn nut before installing

Yamaha Road Star Forward Control Kit Installation Instructions

0

Filed Under (Yamaha) by admin on 08-11-2010

download
Before starting to assemble this forward kit on your motorcycle check the packing list to make sure that the kit you received is the correct one for your model motorcycle and that the foot pegs are the style you ordered (billet or ISO). Next check the contents hardware kit P.N.0109-1000 against the packing list for completeness. Installing The Shift Control Photo 1 Remove wires from horn. Remove the two hex head bolts (Save for later installation) that mount the OEM shift controls to your motorcycle. Unthread stock shift rod at trans shift arm, leaving OEM rod end connected to stock shift arm. Using Original Metric hardware, place a drop of Loctite #242 (blue) to the bolt threads and mount the shift control plate to the motorcycle frame, Photo 2. FORWARD CONTROL KIT PM SHIFT CONTROL ASSEMBLY Note Before torquing the shift control mounting bolts down, tighten them snug and look behind the shift control mounting plate to where it contacts the mounting lug on the frame. Make sure it fits squarely to the lug before proceeding further. Torque the two shift control mounting bolts down to 25 ft-lb. Using a 3/8″ x 1″ hex head bolt with a lock and flat washer put a drop of Loctite #242 (blue) on the threads and insert the bolt through the rear of the control mounting plate and attach the foot-peg pivot to it. Tighten the bolt while holding the footpeg pivot so that its hinge is lined up in a 45˚ rear facing angle. Thread supplied shift rod coupler to stock shift rod end at trans arm. Mount the shift pedal to the other end of the shift ro d using a 5/16″ x 1″ socket head screw and Nylocnut . Adjust the transmission shift linkage so that the shift arm on the forward controls and the shift arm on the transmission are parallel. Secure it with the jam nuts. Apply a drop of Loctite #242 (blue) to the threads under the jam nut before tightening see Photo 3 After you have assembled the shift control onto your motorcycle you must align the footpeg. The folding footpeg assembly uses a blind stud to attach the footpeg to the footpeg pivot. Shim washers (3/8″ x .015″) are used on the stud between the footpeg and the pivot, see Photo 4, so that the top surface of the footpeg is correctly aligned for your foot when it is tightened down on the pivot. This is done by setting a couple of shim washers on the footpeg mounting stud “A” and then screwing the footpeg onto the mounting stud, if the footpeg is rotated to far forward then add another shim washer, if not far enough then remove a shim washer. After you have the selected the correct number of shims for your footpeg, disassemble the footpeg and put a drop of Loctite #271 (red) on both ends of the stud and reassemble the footpeg. This will also need to be done on the brake control footpeg. Setting Up the Master Cylinder The master cylinder pushrod return spring and pushrod boot must be installed on the master cylinder before it is assembled onto the forward control mount. The parts are shown in Photo 5: pushrod boot (A), pushrod return spring (B), spring seat washer (C), and master cylinder (D). Place the return spring seat washer into bore of master cylinder so that is sits on top of the piston retaining snap ring. Next set the pushrod return spring on the seat washer and slide the pushrod boot over the return spring now slip the big end of the boot over the flange on the master cylinder so that the ridge on the inside of the boot fits into groove “A” that is machined into the end of the master cylinder flange, see Photo 6. Installing The Brake Control Unplug stock brake light switch at master cylinder. Remove brake line from rear caliper. Remove the existing brake controls from your motorcycle down to the control mounting lug that is welded on to the frame’s right side, see Photo 8. Save Metric hardware for later use. A Shim Washer PHOTO 4 A B C D PHOTO 5 A PHOTO 6 PHOTO 7 Note For complete brake system removal instructions and precau – tions refer to the appropriate service manual for your year and model motorcycle

Incoming search terms:

2007 Ural Retro Model Installation Manual

0

Filed Under (Ural) by admin on 02-11-2010

download
Kickstart lever : Designed to start the engine. Upon kicking the lever the crankshaft is actuated through the gearbox. The lever is returned to its initial position by the spring inside the gearbox. Gear shift lever: This is a heal shift type of lever. To shift up from a low gear to a high gear the rear arm(heal shift) is pressed. To shift down from a high gear to a low gear the from arm is depressed. Since the heel-toe shift lever is short-coupled, it is much easier to shift up using the heal shift, and to shift down using the toe shift with the ball of your foot. The neutral gear is between the 1st and 2nd gears. It is important to shift smoothly with a constant force, and not to kick the gear shift pedal. Serious damage may result to the shifting mechanism if the gear shift pedal is kicked, rather than pressed urn indicator lamp indicates that the turn signals are activated. Alternator fault indicator lamp , indicates that the charging system is malfunctioning and needs immediate attention. Gearbox neutral lamp indicates that the gearbox is in neutral. Head lamp high beam indicator , indicates that the headlight high beam is activated. Speedometer is on the dash board, with trip and total odometer. The trip odometer is reset to zero by rotating knob (Fig.1, # 3) counterclockwise. Note that the odometer reads in kilometers

HARLEY DAVIDSON SPORTSTER CHROME PRIMARY TRIM COVER KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 08-03-2011

download
INSTALLATION To prevent accidental vehicle start-up, which could cause death or serious injury, disconnect negative (-) battery cable before proceeding. (00048a) 1. Refer to the Owner’s Manual and follow the instructions given to remove the seat and disconnect the negative battery cable at the engine crankcase. Retain all seat mounting hardware. 2. Models with mid foot controls: Remove the two screws retaining the left-side rider footrest and mounting bracket assembly. 3. All models: See Figure 1. Note the installed orientation of the transmission foot shift lever to aid in re-assembly. Use a 1/4 in. hex key to remove the socket head screw (5) holding the shift lever (3 or 4) to the transmission shift lever shaft (1). Remove the lever and rubber washer (2). 4 1 5 3 2 5 is 01929 1. Transmission shift lever shaft 2. Rubber washer 3. Foot shift lever (mid control) 4. Shift lever (forward control) 5. Socket head screw Figure 1. Shift Lever Removal 4 2 3 1 is 01930 Figure 2. Primary Cover Mounting Screw Locations NOTE Remove ONLY the four screws shown. 4. See Figure 2 and Figure 3. Remove and discard the primary cover hex-socket head screws from the four locations shown. 5. Refer to CLUTCH CONTROL: REMOVAL: CLUTCH CABLE-LOWER in the Service Manual to remove the clutch cable at the lower end with these exceptions: •The negative battery cable has already been disconnected, and •On mid-control models, the rider footrest has already been removed. 6. See CLUTCH LEVER AND CLUTCH CABLE-UPPER to remove the clutch cable at the upper end. NOTE Be careful not to scratch the paint on the frame tube when removing the clips. 7. Carefully remove the two vinyl-coated spring steel clips that retain the clutch cable to the frame downtube. 8. Obtain all of the items from the kit. 9. See Figure 2. Insert a chrome screw (3), from the outside, through the hole in location 3 on the chrome trim cover. Place the thinner steel spacer (4) onto the threads of the screw from the inside of the trim cover. 10. Use a 5/32 inch hex key on the screw head, and grip one of the Nylon keeper washers (6) with a pliers. Install the washer onto the screw until several threads extend from the washer, capturing the screw and spacer on the trim cover. 11. Insert the remaining chrome screws, from the outside, through the holes in locations 1, 2 and 4 on the chrome trim cover. Place a thicker steel spacer (5) onto the threads of each screw from the inside of the trim cover. 12. Thread a Nylon keeper washer onto each of the screws as described in Step 10. 13. Position the trim cover over the primary cover with the transmission shift lever shaft extending through the clearance hole (A) in the chrome trim cover. 14. Thread one of the chrome screws into the mating primary cover mounting hole for several threads, taking care not to cross-thread the screw in the hole. 15. Carefully start the remaining screws partially into their mating holes. Continue tightening the screws in turn

harley- davidson DYNA BLACK FORWARD CONTROL KIT installation Manual

0

Filed Under (Harley Davidson) by admin on 15-03-2012

download
1. Disconnect battery cable, negative (-) cable first. 2. Remove the left side rider footrest assembly. Save the footrest and fasteners for installation. Discard the remaining hardware. 3. From the kit, press hole plugs (8) into the screw holes on the frame where the stock footrest assembly was mounted. 4. Remove plugs from forward control frame mount (I) and discard. 5. Remove the foot shifter lever (A) and shifter peg (D). Discard the old foot shifter lever (A). Save the foot shifter lever hardware and shifter peg (D) for future use. 6. See Figure 2. Remove the primary chaincase cover (6) and primary chaincase housing (1). Refer to your model motorcycles Service Manual for removal procedures. NOTE See Figure 1. Before removing the gear shifter lever (1) ((H) in Table 1), it is necessary to mark the correct orientation of the lever. Using a marking tool, draw a location marking (4) on the end of the splined shaft (2) across from the casting split (3). This will allow the new gear shifter lever to be installed in the same orientation as the old lever. 5 3 4 1 2 is 02083 1. Gear shifter lever 2. Splined shaft 3. Casting split 4. Location marking 5. Lever bolt Figure 1. Gear Shifter Lever Orientation 7. After marking the gear shifter lever orientation, loosen the lever bolt (5) and remove the old shifter lever. Discard the old gear shifter lever but keep the lever bolt. From the kit, install the new gear shifter lever onto the splined shaft in the same orientation as the old shifter lever. Tighten the lever bolt to 18-22 ft-lbs (24.4-29.8 Nm)

HARLEY DAVIDSON SPORTSTER FORWARD CONTROL KITS REMOVAL AND INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 07-02-2011

download
Remove Stock Shift Lever and Footrest Assembly 1. See Figure 1. Loosen the shift lever retaining screw (2) securing the shift lever (1) to the shifter shaft. Slide the shift lever off the splined shaft. Remove shifter peg from lever and save for installation. Discard shift lever. 2. Remove the two socket head screws (4) securing the footrest bracket (3) to the frame and remove footrest. Discard screws. 3. See Figure 6. Obtain two hole plugs (1) from kit and firmly press plugs into frame screw holes remaining from footrest removal. 4. See Figure 2. Remove the retaining ring (1) from the clevis to free the footrest clevis pin (4). Remove the clevis pin and footrest (3) from the footrest support. Save footrest for installation. Discard retaining ring, clevis pin, spring washer and footrest bracket. 1 2 4 3 is03193 1. Shift lever 2. Retaining screw 3. Footrest bracket 4. Socket head screw (2) Figure 1. Remove Shift Lever and Footrest 5 1 3 2 4 is03194 1. Retaining ring 2. Spring washer 3. Footrest 4. Clevis pin 5. Footrest bracket Figure 2. Remove Left Footrest from Support Remove Stock Brake Pedal and Footrest Assembly 1. See Figure 3. At the right footrest, remove the retaining ring (1) clevis pin (2), footrest (3) and spring washer (4). Discard all hardware but save footrest for installation. 2. Remove the exhaust to access the brake rod. Follow the instructions in the appropriate Service Manual. 3. Remove brake rod (5) from brake pedal and master cylinder bell crank. Discard brake rod INSTALLATION Install Forward Control Brake Pedal and Footrest Assemblies 1. See Figure 5 and Figure 6. At the lower front of the right frame downtube, remove the two screws securing the J- clip (B) to the frame. Discard the screws but save J-clip for installation. 2. Install the other end of the brake rod into the brake pedal assembly (8). Tighten to 84-144 in-lbs (9.5-16.3 Nm) . NOTE Assemble the brake pedal and footpeg clevis onto the footrest support bracket (as described in the next step) prior to mounting the support bracket to the frame. This will allow easier installation of the footrest mount clevis retaining ring (installed to grooved end of footrest mount clevis). 3. Slide the brake pedal (8) onto footrest mount clevis (11) then slide clevis into footrest/brake pedal support bracket (9). Align hole in the clevis with hole in the support bracket and install screw (6). Tighten the screw to 18-22 ft-lbs (24.4-29.9 Nm) . 4. Install the footrest mount clevis retaining ring (18) to the groove at the end of the footpeg clevis. 5. Position the J-clip (from Step 1) against the frame aligning the mounting holes. Mount the footrest/brake pedal support bracket (9) and J-clip to frame using the new screws (3). Tighten the bracket to 45-50 ft-lbs (61.1- 67.9 Nm) . 6. Obtain the brake rod (15) from kit and thread one end into the master cylinder bell crank. Tighten to 120-180 in-lbs (13.6-20.3 Nm) . 7. Install footpeg on clevis with spring washer (2). Make sure spring washer is positioned inside clevis (11) with the square edge toward the inside. Align holes and push clevis pin (7) from top down through hole in clevis. Secure clevis pin using the new retaining ring (17). 8. Install exhaust following the instructions in the appropriate Service Manual. Install Forward Control Shift Lever Assembly

Incoming search terms:

Incoming search terms: