adjusting 2510 mule governor

You search Auto repair manual PDF adjusting 2510 mule governor, if there are search results will appear below. If search results do not exist, please search by others keyword.



  adjusting 2510 mule governor Direct Download speed 5282 Kb/s

  adjusting 2510 mule governor Full Version speed 6162 Kb/s



Kawasaki Mule Lift Kit Installation Manual

0

Filed Under (Kawasaki) by admin on 04-05-2012

download
Front Lift Installation 1. Ensuring that the parking brake is set, place jack under center of the Mule front end and lift until front wheels clear the ground. Be careful to support Mule properly so that it is secure, but so that the A-arms and struts can droop to full extension. 2. Remove front wheels. 3. If applicable, remove the heater to allow access to the strut mount behind the heater coil. Heater 4. Starting with the left side (driver side), remove the cotter pin and castle nut that secures the strut to the strut mount. Castle Nut & Pen 5. Push bolt through the bolthole, taking care not to damage the brake line that is attached to the bolt. If you are having difficulty removing the bolt, you may have to remove the brake lines that are attached to the front brakes. In this case refer to owners manual for removing brake lines. Screwdriver NOTE: Keep in mind that if you remove the brake lines you must bleed your brakes according to operator’s manual. 6. Once the bottom of the strut has been loosened, then unbolt the top of the strut. The nuts securing the top strut can be located in the dash of the Mule on the left and right sides. In most cases these nuts are easily accessible, but you may have to remove the glove box or heater coils, depending on the model and options purchased with the Mule.

Incoming search terms:

KTM 990 SUPER DUKE 950 SUPERMOTO 950 SUPER ENDURO REPAIR MANUAL

0

Filed Under (KTM) by admin on 22-11-2010

download
Adjusting the position of the compression and rebound damping Rebound damping: -Turn in the adjusting screw 1 in a clockwise direction all the way to the stop. -Turn back the respective number of clicks in a counterclockwise direction. Compression damping, low speed: -Turn in the adjusting screw 2 in a clockwise direction all the way to the stop. -Turn back the respective number of clicks in a counterclockwise direction. Compression damping, high speed: -Turn in the adjusting screw 3 in a clockwise direction all the way to the stop. -Turn back the respective number of clicks in a counterclockwise direction. Adjusting the spring preload NOTE: the spring preload is the difference between the unloaded and preloaded length of the spring. -Tighten the adjusting nut 4 with the special tool T106 until you have the prescribed spring preload. -Tighten the lock screw on the adjusting nut Disassembling the shock absorber -Write down the spring preload. -Write down the rebound and compression damping settings, counting the clicks or number of turns while turning in a clockwise direction. -Unscrew all of the adjusting screws in a counterclockwise direction. -Clamp the upper part of the shock absorber in a vise as shown in the photo, using protective jaws. -Loosen the lock screw 1 (AH 4 mm), loosen the adjusting nut 2 using the special tool T106 3 and relieve the spring. NOTE: mark the position of the lock screw. -Press the spring down with the special tool T101S and pull out the spring retainer 4 . -Remove the washers 5 and spring 6 . 4-2 Repair manual WP Shock absorber 990 Super Duke, 950 Supermoto, 950

HARLEY DAVIDSON SOFTAIL ULTIMA STYLE ADJUSTABLE SHOCKS MANUAL

0

Filed Under (Harley Davidson) by admin on 03-03-2011

download
ADJUSTING SPRING PRELOAD (STIFFNESS). NOTE: Shocks typically come set at their loosest (softest) setting. Adjustment range is approximately 4 full rotations. Step 1: Loosen preload adjustment locknut. (see fig. 1) Step 2: Using supplied special tool with a 3/8 ratchet, turn adjusting plate clockwise to stiffen preload & counter-clockwise to loosen preload. (see fig. 2) Step 3: Once preload has been set, lock down preload adjusting nut using blue (med strength) thread locker ADJUSTING RIDE HEIGHT. NOTE: Extending shock assembly lowers frame/fender height. Shortening shock assembly will raise frame/fender height. NOTE: Always check clearances during & after adjusting ride height. Step 1: Loosen ride height adjusting locknut. (see fig. 3) Step 2: Rotate end to desired height. Always leave at least 1 inch of threads engaged in the female threaded shaft. (see fig. 4) Step 3: Lock down ride height adjusting locknut using blue (med strength) threadlocker. (see fig. 5) Step 4: After adjusting ride height on both shocks, verify that they are the same length by measuring from their mounting points. (see fig. 6)

2005-2007 KTM 5018 DCC 5018 SXS 5018 SMR WP SHOCK ABSORBER REPAIR MANUAL

0

Filed Under (KTM) by admin on 13-02-2011

download
liter fuel consumption is equivalent to approx. 15 operating hours Check the bearing in the shock absorber top / replace if necessary Check the piston rod on scratches / leakage Check the static sag – before riding Check the spring Check the bump rubber Check the O-ring of the spring retainer / replace if necessary Complete maintenance of the shock absorber 10 hours 65 liter 20 hours 130 liter 30 hours 200 liter 40 hours 260 liter 50 hours 325 liter 60 hours 400 liter 70 hours 455 liter 80 hours 520 liter 90 hours 600 liter 100 hours 665 liter Adjusting the position of the compression and rebound damping Rebound damping: -Turn in the adjusting screw 1 in a clockwise direction all the way to the stop. -Turn back the respective number of clicks in a counterclockwise direction. Compression damping, low speed: -Turn in the adjusting screw 2 in a clockwise direction all the way to the stop. -Turn back the respective number of clicks in a counterclockwise direction. Compression damping, high speed: -Turn in the adjusting screw 3 in a clockwise direction all the way to the stop. -Turn back the respective number of clicks in a counterclockwise direction. Adjusting the spring preload NOTE: the spring preload is the difference between the unloaded and preloaded length of the spring. -Tighten the adjusting nut 4 with the special tool T106 until you have the prescribed spring preload. -Tighten the lock screw on the adjusting nut. Recommended periodic maintenance and inspection of the 5018 SXS/SMR Shock absorber

Incoming search terms:

Kawasaki Mule Roof 600, 610 and 4010 Trans Crew, Roof Installation Manual

0

Filed Under (Kawasaki) by admin on 02-05-2012

download
INSTALLTION INSTRUCTIONS – Mule 600/610 (4010 Trans skip to pg 4) 1. Place Roof Panel on top of UTV Roll cage and center front to back, and left to right. 2. Using Figure 1 Below – place UTV Roof Mounting Brackets around roll cage bar and using a marker, mark the position of the holes needed in the roof for each Roof Mounting bracket . Figure 1 Copyright 2007 DiamondBack Automotive Accessories, Inc. Page 3 3. Next, remove the roof from the roll cage and using a drill with 1/4″ bit, drill holes using the marks as a guide. 4. Cut (4) 3″ strips of adhesive foam and apply to roof in where mounting brackets are positioned to prevent roof rattling once mounted. Foam should run in the direction of the roll cage as shown in Figure 1 above. 5. Next, reposition the roof on the roll cage according to step 1. 6. Prior to attaching the roof mount brackets, cut the remaining adhesive foam in half and apply one section to the roof in the center of the roof where roof and each roll cage bar meet as shown in Figures 1 above. If additional tape is required to prevent rattling it can be purchased from any hardware store as window sealant foam tape. 7. Next, attach the roof mount brackets according to Figure 2. Use channel locks or pliers to hold top of carriage bolt and turn nut with 7/16″ socket.

Incoming search terms:

KTM 125/ 200/ 250/ 300 SX, MXC, EXC SERVICE MANUAL

0

Filed Under (KTM) by admin on 28-11-2010

download
Compression damping of shock absorber (MXC, EXC) The compression damping (during compression) can be adjusted for the MXC and EXC shock absorbers (Mono Compression Control). The degree of damping can be adjusted by turning adjusting screw 1 with a screwdriver. Turning in a clockwise direction will increase the damping, turning in a counterclockwise direction will decrease the damping. STANDARD ADJUSTMENT: -Turn the adjusting screw clockwise to the stop. -Then turn the adjusting screw counterclockwise, counting the number of clicks that corresponds to the respective type of shock absorber. Type White Power 1218X757…………..17 clicks Type White Power 1218X759…………..17 clicks * WARNING * THE DAMPING UNIT OF THE SHOCK ABSORBER IS FILLED WITH HIGH – COMPRESSION NITROGEN . NEVER TRY TO TAKE THE SHOCK ABSORBER APART OR TO DO ANY MAINTEN – ANCE WORK YOURSELF . SEVERE INJURIES COULD BE THE RESULT . NEVER UNSCREW THE BLACK SCREW 2 CONNECTION (24 MM ). Rebound damping of shock absorber (SX, MXC, EXC) By using the adjusting screw 3 , the degree of damping of the rebound can be adjusted. Turn the knob to the right side to increase damping, turn it to the left side to reduce damping during rebounding. STANDARD ADJUSTMENT: -Turn the adjusting screw clockwise to the stop. -Then turn the adjusting screw counterclockwise, counting the number of clicks that corresponds to the respective type of shock absorber. Type White Power 1218X756…………..28 clicks Type White Power 1218X757…………..28 clicks Type White Power 1218X759…………..26 clicks * WARNING * THE DAMPING UNIT OF THE SHOCK ABSORBER IS FILLED WITH HIGH – COMPRESSION NITROGEN . N EVERTRYTOTAKETHESHOCKABSORBERAPARTORTODOANYMAINTE – NANCE WORK YOURSELF . SEVERE INJURIES COULD BE THE RESULT . NEVER UNSCREW THE BLACK SCREW 4 CONNECTION (15 MM )

Incoming search terms:

YAMAHA YZF-R1P YZF-R1PC SPECIFICATIONS AND OWNER'S MANUAL

0

Filed Under (Yamaha) by admin on 24-11-2010

download
GASOLINE IS HIGHLY FLAMMABLE: a. Always turn the engine off when refueling. b. Take care not to spill any gasoline on the engine or exhaust system when refueling. c. Never refuel while smoking or in the vicinity of an open flame. 2. Never start the engine or let it run for any length of time in a closed area. The exhaust fumes are poisonous and may cause loss of consciousness and death within a short time. Always operate your motorcycle in an area that has adequate ventilation. 3. Always turn the engine off before leaving the motorcycle unattended and remove the key from the main switch. When parking the motorcycle, note the following: SAFETY INFORMATION 1 1-6 a. The engine and exhaust system may be hot, therefore, park the motorcycle in a place where pedestrians or children are not likely to touch these hot areas. b. Do not park the motorcycle on a slope or soft ground, otherwise it may fall over. c. Do not park the motorcycle near a flammable source, (e.g., a kerosene heater, or near an open flame), otherwise it could catch fire. 4. When transporting the motorcycle in another vehicle, make sure that it is kept upright. If the motorcycle should lean over, gasoline may leak out of the fuel tank. 5. If you should swallow any gasoline, inhale a lot of gasoline vapor, or allow gasoline to get into your eyes, see your doctor immediately. If any gasoline spills on your skin or clothing, immediately wash the affected area with soap and water and change your clothes 1. Fuse box (page 6-40) 2. Front fork compression damping force adjusting screw (page 3-19) 3. Front fork rebound damping force adjusting screw (page 3-19) 4. Front fork spring preload adjusting bolt (page 3-18) 5. Front brake fluid reservoir (page 6-31) 6. Shock absorber assembly spring preload adjusting ring (page 3-20) 7. Shock absorber assembly compression damping force adjusting screw (page 3-21) 8. Owner’s tool kit (page 6-1) 9. Shock absorber assembly rebound damping force adjusting screw (page 3-21) 10. Engine oil drain bolt (page 6-14) 11. Engine oil filter cartridge

2005-2007 Kawasaki 610 Mule Winch Mount Installation Instructions

0

Filed Under (Kawasaki) by admin on 25-10-2010

download
1. Remove the plastic lower front cover. 2. Remove the two bolts on the left side mud shield that connect to the frame for easier access. 3. Install the winch to the winch mount using the hardware supplied with the winch. 4. Install the winch and mount per the illustration using the provided U-Bolts, flat washers and nuts around the frame tubes and through the mount. Tighten all nuts and bolts securely. 5. Install the roller fairlead to the winch mount using (2) 5/16″ x 3/4″ bolts and 5/16″ nylock nuts provided. (Rollers should turn freely. NOTE: Bottom roller may need to be removed to run wire rope through. 6. Using the instructions provided with the winch, wire accordingly. 7. Reinstall the two bolts from the mud shield. 8. Reinstall the plastic lower front cover. NOTE: For some winches, this cover may need to be trimmed so it does not rub

Incoming search terms:

Kawasaki Mule 610 Windshield Installation And Operations Manual

0

Filed Under (Kawasaki) by admin on 25-10-2010

download
Seizmik Hybrid Roof Frame Kit Contents: A. Windshield Mount Top Brackets and Hardware (2) B. Windshield Clamps and Hardware (2) (not shown) C. Windshield (1) (not shown) A B C D E F G H I J K L M Note: All hardware and brackets may not be shown in this view. Windshield Top Mount Hardware Includes: A. M6x22mm Socket Head Bolts (4) B. M6x12mm Socket Head Bolts (4) C. M8 Standard Flat Washers (4) D. Compression Sleve (2) E. M8x18mm Socket Head Bolt (2) F. Windshield Stay Assembly (2) G. 1.875″ Bar Clamp Half (4) H. Windshield bracket (2) I. Windshield clamp plate (2) J. Windshield clamp gasket (4) K. M6x25mm hex head bolt (4) L. M6 flat washer (8) M. M6 hex lock nut (4) Windsheild Lower Clamp Hardware (not shown) Includes: A. M6 x 40mm Zinc Coated Hex Head Bolt (2) B. M6 Standard Flat Washer (4) C. M6 Zinc Coated Nut (2) D. M6 Wide Flange Nut (2) E. 2″ Tube Clamp (2) F. 2″ Rubber Grip Strip (2) 3 Installation Instructions: Use the passenger side clamp to ensure proper positioning. The clamp should be positioned as shown. The driver’s side clamp should be even with the passenger’s side

KAWASAKI MULE Electric Steering Installation Manual And Removal

0

Filed Under (Kawasaki) by admin on 05-05-2012

download
Remove plastic center cap on steering wheel by prying off with a small screwdriver. Remove steering wheel nut and remove steering wheel by pulling up on wheel. If wheel is tight have a partner tap on the shaft while pulling up on wheel. Note: Do not mushroom threads on shaft. Remove all screws that retain dash to body of vehicle. Disconnect all electrical connections at back of dash. Mark all wires to ensure easy install. Remove lower steering shaft bolt at rack and pinion. Remove upper bolt at base of steering column. Remove the 2 bolts that retain the steering column to the frame and remove the column and the shaft assembly. Remove lower u-joint on steering column shaft & replace it with supplied u-joint. There is a welded wire retainer on the lower dash tube where the electric motor will sit. You will need to grind off this piece and smooth. Remove the master cylinder bolt closest to the driver side and discard bolt. Your motor and module has been shipped together bolted to the bracket. It is important to follow the install sequence to ensure a proper installation. The lower shaft on the steering motor is marked on the shaft and on the motor. These marks must not be changed. If you remove the shaft it needs to be installed back in the same spot.

Incoming search terms:

Incoming search terms: