adjusting rear suspension on 2008 suzuki m109r

You search Auto repair manual PDF adjusting rear suspension on 2008 suzuki m109r, if there are search results will appear below. If search results do not exist, please search by others keyword.



  adjusting rear suspension on 2008 suzuki m109r Direct Download speed 5282 Kb/s

  adjusting rear suspension on 2008 suzuki m109r Full Version speed 6162 Kb/s



1999-2008 FLHT Series Harley- Davidson Trike Conversion Kit Installation Instructions

0

Filed Under (Harley Davidson) by admin on 04-12-2010

download
1. Place the motorcycle on the lift. 2. Place a suitable Jack under the Frame of the Motorcycle and tie down securely. 3. Remove Drain Plug from Primary Cover Assembly and drain oil. 4. Slide Rubber Boot off of the Clutch Cable Adjuster. Loosen and back the Jam nut away from the Clutch Cable Adjuster. Move Clutch Cable Adjuster towards the Jam Nut to introduce free play in the Clutch Lever. 5. Remove the ¼ – 20 Phillips head screw and Seat. 6. Disconnect negative Battery Terminal. 7. Remove two ¼ – 20 flanged hex nuts from the Stud Plate. Save the Passenger Handrail and two nuts. 8. Remove the Saddle Bags. 9. Remove the Right and Left Side Covers. 10. Remove Inner Tour Pak Molded Liner. 11. Disconnect the Tour Pak wiring. 12. Remove five ¼ – 20 HHCS, ¼ – 20 nyloc nuts, and Aluminum Spacers. 13. Remove Tour Pak from Top Support Tube. 14. Loosen Muffler Clamp on both Mufflers and remove 2 5/16 – 18 HHCS per Muffler. Remove and discard both Mufflers. Save Muffler Clamps. 15. Remove and discard Muffler Support Plates. 16. Remove both ¼ – 20 HHCS and Front Saddle Bag Brackets. 17. Remove the twelve 5/16 – 18 Torx HCS six 5/16 – 18 nuts, and the Left and Right Saddle Bag Guards. 18. Remove the Air Line Junction from the Rear Fender. 19. Disconnect the Rear Lamp Wiring Harness and remove from T-stud Clip.
6 20. Remove two 5/16 – 18 Phillips head screws. Remove the Left and Right Frame Covers. 21. Remove two 5/16 – 18 Torx HCS. Remove and save the Top Tour Pak Support Tube Top. 22. Remove four 5/16 – 18 Torx HCS. Remove the Left and Right Rear Saddle Bag Guard Support Bracket. 23. Remove four 5/16 – 18 HHCS. Remove and save the Tour Pak Support Tube Bottom. 24. Remove and discard the Air Valve Assembly Bracket. 25. Remove four ½ – 13 HHCS and washers. Remove and discard both Rear Air Shock Absorbers. NOTE: if ABS equipped refer to separate instructions. NOTE: if ABS equipped refer to separate instructions. NOTE: if ABS equipped refer to separate instructions. NOTE: if ABS equipped refer to separate instructions. 26. Drain all Brake Fluid from the Rear Brake System. 27. Cut and remove Cable ties and un-clamp Wire Harness Loops from the Rear Brake Line along its length, including Clamps on Swing Arm. 28. Remove the 10 – 24 flanged HHCS and Rear Brake Hose Clamp from the Right Rear Fork Bracket. 29. Remove ¼ – 20 SHCS from Rear Stop Lamp Switch Bracket. 30. Remove and discard Banjo Bolt and Crush Washers on Rear Brake Caliper. 31. Remove the Spring Clip and nut from the Rear Axle. 32. Remove Rear Axle and Rear Wheel Spacers. 33. Push Rear Wheel Assembly forward and slip Rear Belt off of the Rear Sprocket. 34. Remove Rear Brake Caliper. 35. Slide Rear Wheel Assembly rearward. Remove one 5/16 – 18 Torx HCS from inside the Rear Fender well. 36. Slide Rear Wheel Assembly forward. Remove two 5/16 – 18 Torx HCS. Remove Rear Fender. 37. Remove and save the two Retaining Washers from the Stud Plate. Remove and save the Stud Plate

Incoming search terms:

Harley-Davidson FLH Series 2008 and Down, Independent Suspension Trike Conversion Installation Manual

0

Filed Under (Harley Davidson) by admin on 07-03-2012

download
Protect yourself and others when you have a vehicle up in the air. Anytime you lift a vehicle, either by hoist or a jack, make sure that it is securely supported. b. Make sure the engine is turned off and battery disconnected before you begin work.  Carbon Monoxide poisoning from exhaust gases: Be sure there is adequate ventilation whenever you run the engine.  Burns from hot parts: Let the engine and exhaust system cool before working on those areas.  Injury from moving parts: If running the engine, keep hands, fingers and clothing away from moving/rotating parts. c. Gasoline vapor and hydrogen gases from batteries are explosive. To reduce the possibility of fire or explosion, be careful when working near gasoline and batteries. d. Use only nonflammable solvent, not gasoline, to clean parts e. Never drain or store gasoline in an open container. f. Keep all cigarettes, sparks or flame away from the battery and all fuel related parts. 1.5 Specifications Overall Length: 103″ Overall Width: 57.25″ Wheel Base: 53″ Load Capacity: 600 Lb Tire Size (15″): 205 / 70 / R15 Wheel Size (15″) (4 lug) Offset +35 mm 15x7JJ 4 on 4.5 Tire Pressure: 24-26 PSI Suspension: Double A-arm Independent Rear Differential: Custom-built rear differential utilizing OEM drive belt. Brakes: Original front plus 2 high performance disc brakes at rear. Storage Capacity: 5.75 cubic feet. Two full-face helmets and additional storage.
Harley-Davidson® FLH 2008 & Down Independent Suspension CHAMPION TRIKES Installation Guide Page 6 of 20 Revision 4 2 Removal of Original Parts Secure and raise motorcycle 9 to 10 inches using a quality motorcycle lift. Remove the following from the vehicle. See OEM manual for detailed instructions. Items to be retained for reinstallation after modification are noted.  Seat – to be re-installed; without modification.  Left and right side covers – to be re-installed after modification.  Tour Box – to be re-installed (if so equipped).  Left and right saddle bags (if so equipped).  Left and right rear crash bars, saddlebag rails (if so equipped).  Tour Box mounting frame (if so equipped).  Left and right passenger foot rests – to be re-installed without modification.  Left and right mufflers  Rear wheel NOTE: Prior to removing rear wheel, depress foot brake and secure in down position (e.g., zip-tie to floor board). This will prevent fluid flow when rear brake Caliper is removed.  Remove Rear Caliper (disconnect brake line at Caliper). NOTE: Cap line to prevent introduction of dust / debris into line. Remove Caliper

HARLEY DAVIDSON TRI-BAR AUXILIARY RUNNING LIGHT/ BRAKE LIGHT ASSEMBLY REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 02-03-2011

download
REMOVAL 1. Remove the saddlebags and left side cover. To prevent accidental vehicle start-up, which could cause death or serious injury, remove main fuse before proceeding. (00251b) 2. Remove the main fuse. 3. See Figure 1. Remove six flange nuts (1) from the right and left fender stud plates (2). 1 2 3 5 4 is04366a 1. Nut 2. Stud plate 3. Rear fascia 4. TORX screw 5. Lamp assembly Figure 1. FLHX Rear Fascia and Lamp 4. On the left side of the motorcycle, loosen the set screw and unscrew the radio antenna mast. 5. Gently open the adhesive conduit at the split line to release the rear fascia light harness. 6. At the rear of the motorcycle, spread the top of the fascia to release from the top studs at the side of the fender and then pull the bottom in a downward direction to release the fascia from the fender. If necessary, gently wiggle the fascia while pulling. 7. 2006-2008 models only: On the left side of the motorcycle, remove the bolt (with flat washer) to remove the passenger seat strap and saddlebag front mounting bracket from the chrome frame tube cover. 8. Remove the screw and chrome frame tube cover. NOTE ALL models: Make note of the wire routing and location of all cable straps. New light wiring installs the same way. 9. See Figure 2. Release the rear fascia light wires from the wire clip (1). Cut the cable straps (2) to release the rear fascia light harness (3) and radio antenna cable. 10. 2006-2008 models: Disconnect the rear fascia light connector [12B] located inboard of the upper frame tube. 2009 and later models: Disconnect the rear fascia light connector [12B] located to the rear of the fuse panel. 11. See Figure 1. Remove the two T-20 TORX® screws to release the light assembly from the fascia. Save the screws for installation of the new light. 1 3 4 2 is04378 1. Wire clip 2. Cable strap 3. Fascia light harness 4. Flange nut Figure 2. Rear Fascia Light Harness INSTALLATION 1. Route the rear fascia light wires forward through the cable clip at the top of the radio antenna bracket and then upward in front of the saddlebag rear mounting bracket to the inboard side of the upper frame tube. 2. 2006-2008 models: On the inboard side of the upper frame tube, mate the pin and socket housings of the rear fascia light connector [12]. 2009 and later models: To the rear of the fuse panel, mate the pin and socket housings of the rear fascia light connector [12]. 3. Using the slotted hole, install a new cable strap to secure the rear fascia light wires and radio antenna cable to the rear fender support. 4. Install a new cable strap to secure the rear fascia light wires and radio antenna cable to the shoulder of the upper frame tube (just in front of the air valve mounting bracket).

Incoming search terms:

HARLEY DAVIDSON LOW-PROFILE REAR TOURING SUSPENSION KIT Installation

0

Filed Under (Harley Davidson) by admin on 30-11-2010

download
1. Refer to the Service Manual and follow the instructions given to remove the seat and disconnect the battery cables, negative cable first. 2. Raise the rear end of the motorcycle so that the rear wheel is just off the ground. Support the motorcycle with suitable blocking under the frame. NOTE Retain the original fasteners for installation of new shocks. 3. Remove the saddlebags from the motorcycle. See the Touring model’s Owner’s Manual for saddlebag removal. 4. Fasten the air pump, part number 54630-03A to the rear air-suspension adjustment valve on the motorcycle. See the Touring model’s owner’s manual for valve location. Add 3-5 psi to clear the line but do NOT exceed 50 psi. 5. Using the pressure-relief valve located below the gauge on the pump, release the air pressure from the rear sus- pension. Failure to relieve air pressure from the rear suspension could cause injury during shock-absorber removal. Use caution when bleeding air from the suspension. Moisture combined with lubricant may leak on to the rear wheel, tire, and/or brake components and adversely affect traction, which could result in death or serious injury. (00084a) 6. See Figure 1 and Figure 2. Remove the air hoses from the shock absorber air-hose fittings. NOTE Press the plastic collar down on the air-hose fitting to remove and install the air hose. 7. Remove the air hose fittings from the shock absorbers. Save the fittings for installation on the new shocks. NOTE Air-suspension shock absorbers are oil filled and must be kept upright at all times to prevent oil leakage. 8. Remove the lower mounting bolts and washers from the shock absorbers

Incoming search terms:

2003 – 2008 4Runner AND 2007 – 2008 FJ Cruiser FRONT AND REAR DIFFERENTIAL GEAR OIL SPECIFICATION CHANGE

0

Filed Under (Toyota Manuals) by admin on 14-11-2011

download
75W-85 GL5 synthetic gear oil beginning with the 2008 model year. This new synthetic gear oil is compatible with 2003 – 2007 model year 4Runner and 2007 model year FJ Cruiser differentials. Please refer to the Parts Information section below for information about this gear oil and use this gear oil (or equivalent) when filling front or rear differentials with oil. 2003 – 2008 model year 4Runner vehicles. 2007 – 2008 model year FJ Cruiser vehicles. PREVIOUS PART NUMBER CURRENT PART NUMBER PART NAME TYPE QTY N/A 08885-02606 Toyota Genuine Differential Gear Oil LX 75W-85 API GL-5 SAE 75W-85 LSD As Needed N/A 08885-02506 Toyota Genuine Differential Gear Oil LT 75W-85 API GL-5 SAE 75W-85 w/o LSD As Needed Refer to the diagram below to identify if LSD or non-LSD gear oil is used on the vehicle. For applicable vehicles, there is a caution label above the filler plug, as shown below

Incoming search terms:

Yamaha Rear Suspension Lowering Kit installation Manual

0

Filed Under (Yamaha) by admin on 08-11-2010

download
1. This lowering method requires replacement rear suspension coupling components. This is a simple task, and is completely reversible. In addition, this kit provides for a 0″ setting, to easily return your bike to its original height. First, raise the rear tire off of the ground by the frame before you begin. Raise the motorcycle so no weight is applied to the rear wheel, allowing the rear wheel to spin freely. 2. Next, become familiar with your lowering kit. You’ll notice that there are two corners of the lowering component with two holes each, and one corner with a single hole. The corner with the single hole attaches to the swingarm (the bolt that is closest to the rear wheel). The only important part of this familiarization process, is to make sure that you get the part oriented in the correct position. The following photos will explain the purpose of the different holes, and also help you turn the part in the correct position before you install it. Look at the first photo on the next page: In the photo above, the part is positioned just as it should be, for installation on the left-hand side (kickstand side) of the motorcycle. A quick measurement will show that Dimension “A” on Side “A” should be shorter than Dimension “B” on Side “B”. If not, flip your part over (turn the face you are viewing away from you, but keep the corners with two holes on your left), and measure again. Next, study the photo below for info on the different heights you can set your bike to… When installed, Hole “0″ will place the bike at it’s original height. Placing the top bolt in Hole 1, and the bottom bolt in Hole 0, the bike will be lowered approximately ¾”. Placing the top bolt in Hole 1, and the bottom bolt in Hole 1, the bike will be lowered approximately 2″. Simple, eh? Now, let’s move on to installation. 3. Below is a photo of the factory suspension coupling as installed in your motorcycle. This photo was taken from the LH side of the bike, to keep things in perspective with our previous photos. Loosen the three bolts holding the original suspension coupling, and remove. Be aware that the rear wheel will drop down when the bolts are removed, just so there are no surprises!

Incoming search terms:

1981-1983 Yamaha Virago 750 & 920 Installation Instructions

0

Filed Under (Yamaha) by admin on 11-02-2012

download
Start by loosening the rear cylinder down tube bolt located on the top of the old mufflers center collector in front of the rear tire. 2. Remove both of the front cylinder exhaust pipe head nuts and set them to the side for reuse with the MAC exhaust system. 3. Remove the right side passenger’s foot peg. Set the foot peg aside as you will need to reinstall it. 4. Remove the left side passenger’s foot peg. Set this foot peg aside as it will also need to be reinstalled. Note: When you remove this bolt the entire exhaust system will be loose and may fall. You will need to support the old exhaust at this point to keep from injuring yourself. Gently move the old exhaust system side to side to remove it from the rear cylinder down tube. Once the exhaust system is loose from the down tube remove the system from under the Virago. 5. Remove the bolt holding the rear brake pedal in place and remove the brake pedal from the motorcycle. Note: Set both the bolt and the pedal aside for reinstallation. 6. Next loosen the nut on the drivers right foot peg, 1 full turn to start with. Then remove the rear nut on the same foot peg. (Note: The bolt that this nut is on goes completely through the motorcycle. This is the center stand mounting bolt.) Now remove the front nut and set both aside for reuse with the MAC system. 7. Install the center stand stop bracket under the left passenger foot peg. Install this bracket with the 90° bend facing down and towards the rear tire. (Note: Center stand sop bracket in provided in the hardware kit and is approx. 5″ long with a 90° bend in it.) Adjust the bracket by one of the large bolts through the foot peg then through the bracket and then install it into the stock location. Put on one of the washers and a nut and snug up the nut. Lower the center stand until the center stand come in to contact with the bottom of the bracket. Tighten the nut until it will hold the bracket securely. 8. Install the rear down tube clamp onto the rear muffler and install the medium sized nut/bolt/washer onto the clamp just finger tight. 9. Install the (2) small bolts into the channel bracket on the rear muffler. Install the rear mounting bracket onto the two bolts and then install the washers and nuts onto each. Tighten the (2) nuts only slight amount so that you can slide the bracket front to rear to insure that when you install the bracket you position it properly. 10. Slide the rear pipe onto the rear down tube about ¼”to ¾” past the pre-cut slots on the rear muffler pipe. Slightly snug the clamp making sure that the position of the bolt and nut will not interfere with any moving parts. The final position of this bolt can hit the tire if it is not positioned properly. 11. Install the other large bolt into the right passenger and then through the top hole in the rear muffler mounting bracket. Insert the bolt into the stock location and install the washer and the nut. 12. Align the rear muffler and you can then tighten the nuts on the rear muffler mounting bracket, the cylinder down tube and the right side passenger foot peg.
13. Install the front muffler on the rear most mounting bolt of the drivers foot peg and put the stock nut back onto the bolt. Hand tighten the bolt only at this time. Note: Install the nut at this time is only to support the muffler and to insure that the pipe does not fall on the ground while you complete the next step. 14. Lift the front head pipe into position and start the stock nuts onto the studs. It is strongly recommended that you install new exhaust gasket at this time. Note: The new exhaust gaskets are not included in the kit but are available at your local Yamaha Dealer. After gaskets are installed hand tighten the front head pipe. 15. Remove the nut from the drivers foot peg bolt and reinstall the drivers foot peg. Note: Hand tighten only at this time. 16. Finish tightening the nuts on the front head pipes. (Install these nuts according to Yamaha’s Factory specifications.) Once the nuts are tightened on the head pipe you can then tighten the drivers foot peg nuts. 17. Reinstall the rear brake pedal and tighten the bolt that holds it on to factory specifications. 18. Check all of the bolts that you have installed of removed to insure that they are tight. 19. Start the motorcycle and check for any leaks. 20. You are finished with your new MAC Exhaust System.

Incoming search terms:

HARLEY DAVIDSON SPORTSTER LOW REAR SUSPENSION KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 13-02-2011

download
INSTALLATION NOTE Internal shock absorber components are not repairable beyond the Service Parts listed on this instruction sheet. Consult your Harley-Davidson dealer if further service is required. The installation procedures for this kit are the same as the original equipment (OE) installation procedures in the Service Manual. Refer to the appropriate Service Manual for the rear suspension system removal and installation procedures. The OE hardware will be re-used in the kit installation. Installation of any accessory suspension components can affect cornering clearance. This could distract the rider, causing loss of control and death or serious injury. (00431b) SHOCK PRELOAD (SPRING) ADJUSTMENT Refer to the appropriate Service Manual for spring adjustment. Spanner wrench (94700-52L) is required for spring adjustment. SERVICE PARTS 1 is04854 Figure 1. Service Parts: Sportster Low Rear Suspension Kit Table 1. Service Parts: Sportster Low Rear Suspension Kit Part Number Description (Quantity) Item 54734-04 Rear shock (2)

Incoming search terms:

HARLEY DAVIDSON TOURING LOW PROFILE REAR SUSPENSION KIT INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 10-02-2011

download
INSTALLATION 1. Refer to the Service Manual and follow the instructions given to remove the seat. Perform this installation when the engine is cool. Working on or near the exhaust system when the engine is hot could result in severe burns. (00311a) Installation of any accessory suspension components can affect cornering clearance. This could distract the rider, causing loss of control and death or serious injury. (00431b) 2. Disconnect the battery cables, negative cable first or remove the main fuse if equipped. 3. Raise the rear end of the motorcycle so that the rear wheel is just off the ground. Support the motorcycle with suitable blocking under the frame. NOTE Retain the original fasteners for installation of new shocks. 4. Remove the saddlebags from the motorcycle. See the Touring model’s Owner’s Manual for saddlebag removal. 5. Fasten the air pump, part number 54630-03A to the rear air suspension adjustment valve on the motorcycle. See the Touring model’s owner’s manual for valve location. Add 3-5 psi to clear the line but do NOT exceed 50 psi. 6. Using the pressure relief valve located below the gauge on the pump, release the air pressure from the rear sus- pension. Use caution when bleeding air from the suspension. Moisture combined with lubricant may leak onto the rear wheel, tire and/or brake components and adversely affect traction, which could result in death or serious injury. (00084a) 7. See Figure 1 and Figure 2. Remove the air hoses from the shock absorber air hose fittings

2008 APRILIA RS125 TECHNICAL SPECIFICATIONS

0

Filed Under (Aprilia) by admin on 06-11-2010

download
specified in the ACU regulations. The appearance from both front, rear and profile of machines must (except when otherwise stated) conform to the homologated shape. The appearance of the exhaust system is excluded from this rule. 2. DISPLACEMENT CAPACITY The displacement must remain at 124.9cc and the bore and stroke (54 x 54.5) must remain as originally produced. 3. MINIMUM WEIGHT The minimum weight at post race control must not be less than 102kg , this includes oil and water but excludes fuel. At any time during the event, the weight of the whole machine (including the tank) must not be less than the minimum weight, with a tolerance of 1kg. 4. NUMBER PLATE COLOURS The background colours and figures for Aprilia Superteens are: FRONT Red background with white numbers – Nitro Newcomers Class White background with black numbers – J&S Championship Class REAR White background with black numbers – Both Classes Placed in accordance with the ACU regulations. 5. CARBURATION INSTRUMENTS Carburation instruments must remain as homologated. Carburettor jets and needles may be replaced. No modification, polishing or cutting is allowed. Only the 28mm bodied standard carburettor is permitted. Electronic or mechanical enriching devices must remain installed and active (If the carburettor is changed from one model to another, the appropriate wiring loom must also be installed and be operative). Bell mouths must be as originally produced by the manufacturer for the homologated machine. Throttle must be standard, quick action throttles are not permitted.
6. FUEL All machines must function on normal unleaded fuel with a maximum lead content of 0.005 g/l (unleaded) and a maximum MON of 90 (RON 102 max) and be readily available from roadside service stations nationwide. 7. FRAME BODY AND REAR SUBFRAME Frame must remain as originally produced by the manufacturer. The sides of the frame body may be covered by a protective part made of composite material. Nothing can be added by welding or removed by machining from the frame body. Engine mounting brackets or plates must remain as originally produced by the manufacturer. Rear sub-frame may be replaced by the later type sub-frame to accept new style bodywork on pre-2006 models, this unit must use the original mounting points. Bolt on accessories to the rear sub-frame may be removed. Front fairing bracket may be altered or replaced on pre-2006 models to accept later bodywork. 8. FRONT FORKS Forks structure (spindle, stanchions, bridges, stem etc) must remain as originally produced by the manufacturer. Standard original internal parts of the forks may be modified. After market damper kits or valves may be installed. The fork caps can be modified or changed to add spring preload/compression and damping adjusters. Dust seals can be modified, changed or removed providing the fork remains totally oil sealed. Any quantity or quality of oil can be used in the front forks. The height and position of the front fork in relation to the fork crowns is free. A steering damper may be added but may not act as a steering lock device. 9. REAR FORK (Swing Arm) Every part of the rear fork must remain as originally produced (including rear fork pivot bolt and rear axle adjuster). Rear wheel stand positioning (support) brackets may be added by welding or bolts. Brackets must have rounded edges viewed from all sides. Fastening screws must be recessed. 10. REAR SUSPENSION UNIT

Incoming search terms: