adjusting valves on an04 fatboy

You search Auto repair manual PDF adjusting valves on an04 fatboy, if there are search results will appear below. If search results do not exist, please search by others keyword.



  adjusting valves on an04 fatboy Direct Download speed 5282 Kb/s

  adjusting valves on an04 fatboy Full Version speed 6162 Kb/s



KTM OM-2 Split Body Floating Ball Valves Installation and Maintenance Instructions

0

Filed Under (KTM) by admin on 26-01-2012

download
Remove the valve from the shipping package (box or pallet) with care taken to avoid any damage to the valve and actuator (plus accessories where applicable). •Before installation, remove the seal discs from the flange. Clean the inside of the valve using an air line that includes an appropriate air-filter. Ensure that there are no solid objects such as pieces of wood, plastic or packing materials within the valve or on the valve seat. •Confirm that the materials of construction listed on the valve nameplates are appropriate for the service intended for and are as specified. When in doubt contact KTM, or your local Tyco facility. •Define the preferred mounting orientation with respect to the system pressure. The arrow on the body helps to identify the upstream side (high pressure) and downstream side (low pressure). •Ensure that all stud bolts and nuts of the body joint are firmly fastened. Caution •Verify that the direction of the flow in the line corresponds to the arrow indicated on the valve body. Valves without the arrow are bi-directional. •See the Actuator User Manual for the actuator preparation. 2.2. Installation Instructions •Ball valves are normally installed in horizontal pipes with the stem facing up. However, there are no limitations regarding the pipe or stem orientation. •Unless otherwise recommended by KTM, the valve should be installed with the ball in the open position, to ensure that the seat rings are not damaged during installation. •Particular care should be taken for valves equipped with “fail-close” actuators. •For operating temperatures above 200°C (392°F), thermal insulation of the valve body is recommended to protect the actuator/accessories from heat beyond the recommended temperature range. •Handling and lifting of the valves during installation MUST be performed following the same criteria and instructions described in points 1.2. and 1.3

Incoming search terms:

KTM 990 SUPER DUKE 950 SUPERMOTO 950 SUPER ENDURO REPAIR MANUAL

0

Filed Under (KTM) by admin on 22-11-2010

download
Adjusting the position of the compression and rebound damping Rebound damping: -Turn in the adjusting screw 1 in a clockwise direction all the way to the stop. -Turn back the respective number of clicks in a counterclockwise direction. Compression damping, low speed: -Turn in the adjusting screw 2 in a clockwise direction all the way to the stop. -Turn back the respective number of clicks in a counterclockwise direction. Compression damping, high speed: -Turn in the adjusting screw 3 in a clockwise direction all the way to the stop. -Turn back the respective number of clicks in a counterclockwise direction. Adjusting the spring preload NOTE: the spring preload is the difference between the unloaded and preloaded length of the spring. -Tighten the adjusting nut 4 with the special tool T106 until you have the prescribed spring preload. -Tighten the lock screw on the adjusting nut Disassembling the shock absorber -Write down the spring preload. -Write down the rebound and compression damping settings, counting the clicks or number of turns while turning in a clockwise direction. -Unscrew all of the adjusting screws in a counterclockwise direction. -Clamp the upper part of the shock absorber in a vise as shown in the photo, using protective jaws. -Loosen the lock screw 1 (AH 4 mm), loosen the adjusting nut 2 using the special tool T106 3 and relieve the spring. NOTE: mark the position of the lock screw. -Press the spring down with the special tool T101S and pull out the spring retainer 4 . -Remove the washers 5 and spring 6 . 4-2 Repair manual WP Shock absorber 990 Super Duke, 950 Supermoto, 950

Incoming search terms:

HARLEY DAVIDSON SOFTAIL ULTIMA STYLE ADJUSTABLE SHOCKS MANUAL

0

Filed Under (Harley Davidson) by admin on 03-03-2011

download
ADJUSTING SPRING PRELOAD (STIFFNESS). NOTE: Shocks typically come set at their loosest (softest) setting. Adjustment range is approximately 4 full rotations. Step 1: Loosen preload adjustment locknut. (see fig. 1) Step 2: Using supplied special tool with a 3/8 ratchet, turn adjusting plate clockwise to stiffen preload & counter-clockwise to loosen preload. (see fig. 2) Step 3: Once preload has been set, lock down preload adjusting nut using blue (med strength) thread locker ADJUSTING RIDE HEIGHT. NOTE: Extending shock assembly lowers frame/fender height. Shortening shock assembly will raise frame/fender height. NOTE: Always check clearances during & after adjusting ride height. Step 1: Loosen ride height adjusting locknut. (see fig. 3) Step 2: Rotate end to desired height. Always leave at least 1 inch of threads engaged in the female threaded shaft. (see fig. 4) Step 3: Lock down ride height adjusting locknut using blue (med strength) threadlocker. (see fig. 5) Step 4: After adjusting ride height on both shocks, verify that they are the same length by measuring from their mounting points. (see fig. 6)

2005-2007 KTM 5018 DCC 5018 SXS 5018 SMR WP SHOCK ABSORBER REPAIR MANUAL

0

Filed Under (KTM) by admin on 13-02-2011

download
liter fuel consumption is equivalent to approx. 15 operating hours Check the bearing in the shock absorber top / replace if necessary Check the piston rod on scratches / leakage Check the static sag – before riding Check the spring Check the bump rubber Check the O-ring of the spring retainer / replace if necessary Complete maintenance of the shock absorber 10 hours 65 liter 20 hours 130 liter 30 hours 200 liter 40 hours 260 liter 50 hours 325 liter 60 hours 400 liter 70 hours 455 liter 80 hours 520 liter 90 hours 600 liter 100 hours 665 liter Adjusting the position of the compression and rebound damping Rebound damping: -Turn in the adjusting screw 1 in a clockwise direction all the way to the stop. -Turn back the respective number of clicks in a counterclockwise direction. Compression damping, low speed: -Turn in the adjusting screw 2 in a clockwise direction all the way to the stop. -Turn back the respective number of clicks in a counterclockwise direction. Compression damping, high speed: -Turn in the adjusting screw 3 in a clockwise direction all the way to the stop. -Turn back the respective number of clicks in a counterclockwise direction. Adjusting the spring preload NOTE: the spring preload is the difference between the unloaded and preloaded length of the spring. -Tighten the adjusting nut 4 with the special tool T106 until you have the prescribed spring preload. -Tighten the lock screw on the adjusting nut. Recommended periodic maintenance and inspection of the 5018 SXS/SMR Shock absorber

Incoming search terms:

Harley-Davidson Valves, Guides And Seats Installation

0

Filed Under (Harley Davidson) by admin on 31-10-2010

download
1: Clean carbon from old guide O.D. before removal. 2: Guide to head press fit .0015″ / .002″ (head smaller than guide). 3: Heat head to approximately 200° – 250° F. 4: Install the guide at room temperature (Head hot & Guide at room temperature). 5: Let head cool to room temperature before final sizing of the bore. 6: Determine desired clearance valve to guide. Recommended clearance Shovel Head with cast iron guides Intake .001″ – .0015″ Exhaust .0015″ – .002″ (Ampco-45 add .001″) 7: Select the correct plug gage by adding the valve stem diameter and clearance desired for the finish diameter. 8: Select a plug gage .0005″ under finish size for the other end of the handle. 9: Finish hone the bore to size, check the size as you hone with the -.0005″ under size pin gage, finish hone to size with the finish plug gage pin. 10: Cut or Grind the seats, lap the valves to seats and check valve seat concentricity before assembling valve springs. 11: Use a good assembly lube, S’NS works great. 12: Use valve stem seals. Factory OE seals will stay tight with guide top size +.005″ to -.015″ from published size. 13: After the head is assembled and still on the bench check for any leakage valve to seat

Adjusting the Pekar K68 for Dnepr or Ural

0

Filed Under (Tips and Review) by admin on 11-11-2010

download
1. Make sure the ignition timing is correct 2. Adjust the valves as necessary to ensure proper operation 3. Run the engine to warm it up a bit 4. Adjust the float setting. To do this, remove the carburetors (leave the throttle cables attached), remove the bowl and turn the carburetor upside down (fuel will spill). The float should look like this: Adjust as necessary by bending the float support (#37 in Figure 1). Reinstall Installation and idle adjustment 1. First you must adjust the idle. It is acceptable per the manual to adjust the idle by using the idle adjust screws (11). This usually involves screwing them then backing out 1 to 1.5 turns. Or you can adjust looking at the sliders 2. If installing the carburetors: a. Remove the cover (2) b. Reomve the slider (3) c. Place the throttle cable through the guide (18) with the spring (4) on the cable. d. Route the cable through the slide catch (6) e. Insert the slide assembly into the chamber and make sure it easily slides up and down. Direct the needle (8) into the opening of the diffuser (angled side visible). f. Screw assembly together and verify via throttle movement that slide moves freely. Attach fuel delivery lines to (12). 3. Using the idle set screw (11) raise the slider so the lower edge is 1-2 mm. 4. Assemble to engine using the proper gaskets (paper – felt – paper). 5. Using the locknut (26) adjust the free play of the throttle cable (2-3 mm) 6. Adjust the idle mixture screw – turn in completely then out 1 to 1.5 turns. * Starting using the K68′s (cold weather) 1. Verify fuel flow. Apply choke (pull 52 in Fig1). 2. Using the ticklers (13) allow fuel to enter the bowl until fuel drains from (14) 3. With the ignition off, kick 1 or 2 times 4. Turn ignition on, and as soon as engine is warmed up (maybe sooner) push choke mechanisms to open choke Idle Adjustment (engine running and warm) 1. Remove one of the spark plug caps, and with the cap shorted, adjust (11) to decrease RPM’s to a point of being minimally steady. 2. Adjust the mixture (15) out until RPM’s decrease. Turn in until RPM’s increase slightly. Then turn in screws ¼ to 1/3 revoultion. 3. Do the same for the second carburetor with the first spark plug cap shorted. 4. With both cylinders, adjust each idle (11) on each carburetor the same amount each until it’s at a steady, minimal RPM. Use small changes. (at this point you can use your airflow tool to check). 5. Sharply increase, then decrease throttle. Then engine must return to low RPMs smoothly. If the engine goes below limits, readjust (11) from step 4. Synchronization of the K68 Note: Rather than using the opposite cylinder shorted to test the pull of the live cylinder carburetor, you can use something like a Twinmax connected to the test ports (27 Fig 1). Or, if you have a model without these ports, use a Synchrometer (Appendix 2) held against the face of the carburetor. These tools merely show airflow passing through each carburetor (which is dependent on the position and wear on the slide). If using these tools, it’s not necessary to do the following steps. You wil want to use a throttle guide (Appendix 1), to show airflow at various throttle settings. Using the flow meter of your choice make sure each carburetor is the same at the various throttle settings. 1. Place the motorcycle on the center stand ensuring the rear wheel is suspended 2. Make sure you have large area to work with (safety issues here) 3. Shift into the highest gear with the engine running 4. Short one spark plug cap to the cylinder (using a nail or something in the fins) 5. Increase the speed to 40-50 km/hr 6. Fix the throttle using the throttle (maybe using a throttle stop screw under the throttle housing). 7. Reconnect other cylinder and using the opposite carburetor determine the speed which should be the same as the first. 8. Adjust the position of this slide to achieve the referenced speed using the locknut at the top of the carburetor.

Incoming search terms:

YAMAHA YZF-R1P YZF-R1PC SPECIFICATIONS AND OWNER'S MANUAL

0

Filed Under (Yamaha) by admin on 24-11-2010

download
GASOLINE IS HIGHLY FLAMMABLE: a. Always turn the engine off when refueling. b. Take care not to spill any gasoline on the engine or exhaust system when refueling. c. Never refuel while smoking or in the vicinity of an open flame. 2. Never start the engine or let it run for any length of time in a closed area. The exhaust fumes are poisonous and may cause loss of consciousness and death within a short time. Always operate your motorcycle in an area that has adequate ventilation. 3. Always turn the engine off before leaving the motorcycle unattended and remove the key from the main switch. When parking the motorcycle, note the following: SAFETY INFORMATION 1 1-6 a. The engine and exhaust system may be hot, therefore, park the motorcycle in a place where pedestrians or children are not likely to touch these hot areas. b. Do not park the motorcycle on a slope or soft ground, otherwise it may fall over. c. Do not park the motorcycle near a flammable source, (e.g., a kerosene heater, or near an open flame), otherwise it could catch fire. 4. When transporting the motorcycle in another vehicle, make sure that it is kept upright. If the motorcycle should lean over, gasoline may leak out of the fuel tank. 5. If you should swallow any gasoline, inhale a lot of gasoline vapor, or allow gasoline to get into your eyes, see your doctor immediately. If any gasoline spills on your skin or clothing, immediately wash the affected area with soap and water and change your clothes 1. Fuse box (page 6-40) 2. Front fork compression damping force adjusting screw (page 3-19) 3. Front fork rebound damping force adjusting screw (page 3-19) 4. Front fork spring preload adjusting bolt (page 3-18) 5. Front brake fluid reservoir (page 6-31) 6. Shock absorber assembly spring preload adjusting ring (page 3-20) 7. Shock absorber assembly compression damping force adjusting screw (page 3-21) 8. Owner’s tool kit (page 6-1) 9. Shock absorber assembly rebound damping force adjusting screw (page 3-21) 10. Engine oil drain bolt (page 6-14) 11. Engine oil filter cartridge

KTM 125/ 200/ 250/ 300 SX, MXC, EXC SERVICE MANUAL

0

Filed Under (KTM) by admin on 28-11-2010

download
Compression damping of shock absorber (MXC, EXC) The compression damping (during compression) can be adjusted for the MXC and EXC shock absorbers (Mono Compression Control). The degree of damping can be adjusted by turning adjusting screw 1 with a screwdriver. Turning in a clockwise direction will increase the damping, turning in a counterclockwise direction will decrease the damping. STANDARD ADJUSTMENT: -Turn the adjusting screw clockwise to the stop. -Then turn the adjusting screw counterclockwise, counting the number of clicks that corresponds to the respective type of shock absorber. Type White Power 1218X757…………..17 clicks Type White Power 1218X759…………..17 clicks * WARNING * THE DAMPING UNIT OF THE SHOCK ABSORBER IS FILLED WITH HIGH – COMPRESSION NITROGEN . NEVER TRY TO TAKE THE SHOCK ABSORBER APART OR TO DO ANY MAINTEN – ANCE WORK YOURSELF . SEVERE INJURIES COULD BE THE RESULT . NEVER UNSCREW THE BLACK SCREW 2 CONNECTION (24 MM ). Rebound damping of shock absorber (SX, MXC, EXC) By using the adjusting screw 3 , the degree of damping of the rebound can be adjusted. Turn the knob to the right side to increase damping, turn it to the left side to reduce damping during rebounding. STANDARD ADJUSTMENT: -Turn the adjusting screw clockwise to the stop. -Then turn the adjusting screw counterclockwise, counting the number of clicks that corresponds to the respective type of shock absorber. Type White Power 1218X756…………..28 clicks Type White Power 1218X757…………..28 clicks Type White Power 1218X759…………..26 clicks * WARNING * THE DAMPING UNIT OF THE SHOCK ABSORBER IS FILLED WITH HIGH – COMPRESSION NITROGEN . N EVERTRYTOTAKETHESHOCKABSORBERAPARTORTODOANYMAINTE – NANCE WORK YOURSELF . SEVERE INJURIES COULD BE THE RESULT . NEVER UNSCREW THE BLACK SCREW 4 CONNECTION (15 MM )

Incoming search terms:

HARLEY DAVIDSON SOFTAIL FATBOY STRAIGHTSHOT HS SLIP ON INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 24-12-2010

download
1. Remove the heat shield from the rear head pipe and the back heat shield (“Z” Shaped) off the lower head pipe. NOTE: Loosen the front heat shield hose clamp closest to this shield to facilitate its removal. 2. Loosen the clamps holding the muffl ers onto the head pipes. 3. Remove the 1/2″ bolts holding muffl ers onto support bar. 4. Slide both muffl ers towards the rear until they are free from the head pipes. NOTE: Assistance and the use of a penetrating lubricant may be required. 5. Remove the stock exhaust clamps from the nose of each muffl er (these will be re-used when installing the new system). QUIET BAFFLE FUELPAK VANCE & HINES EXHAUST SYSTEM INSTALLATION WHEN YOU KNOW THE DIFFERENCE 1. Using the 5/16″ x 3/4″ hex head bolts and washers (supplied) secure the mounting bracket (stamped 419-P)(supplied) to the stock muffl er support bar. NOTE: The bracket should be mounted with the notch facing the front of the motorcycle (Figure 1). 2. Remove muffl ers and heat shields from their protective packaging and place them on a non-abrasive surface such as a blanket, towel or carpet. 3. Carefully lay a muffl er assembly into each straight heat shield and loosely install the hose clamps (supplied) by feeding the tail end of the clamp into the heat shield clips. Note the direction of the screw heads with relation to the muffl er location (Figure 2). 4. Slide stock exhaust clamps onto the nose of each muffl er body. NOTE: Orient the clamp to enable access for tightening the nut after installation. 5. Slide upper muffl er assembly (with heat shield) onto the upper head pipe. Insert nut plate (supplied) into the bracket welded to the muffl er body (Figure 3) and secure to the mounting bracket using the 5/16″ x 5/8″ fl ange head bolts (supplied). 6. Repeat step 5 placing the lower muffl er assembly on the lower head

New Automatic Transmission for Motorcycles Human-Friendly Transmission

0

Filed Under (Honda) by admin on 18-12-2011

download
High-pressure fluid flow The engine rotates the pump swash plate, which has a gear mechanism. The rotating swash plate pushes the pump pistons to increase the pressure on the hydraulic fluid and feed it to the high-pressure annular chamber. The high- pressure fluid is then fed to the oil motor piston chamber where it pushes the pistons forward, which then push the motor swash plate. Power Fluid flow from pump to motor Fluid flow from motor to pump Low-pressure fluid flow The lower-pressure hydraulic fluid returns to the pump through the low-pressure annular chamber. In this way, the fluid circulates between the pump and the motor. Movement of distributor valves and pistons The distributor valves play an important role in fluid circulation. The valves are placed both in the oil pump and motor. When the pump pistons move to the compression side, the valves connect the piston chamber and the high- pressure chamber. When the pump pistons move to the expansion side, the valves allow a connection between the piston chamber and the low-pressure chamber. The valve in the oil motor moves opposite to its counterpart in the pump, ensuring the circulation of fluid within the system

Incoming search terms: