after market exhaust for kawasaki klx 250 13 reg

You search Auto repair manual PDF after market exhaust for kawasaki klx 250 13 reg, if there are search results will appear below. If search results do not exist, please search by others keyword.



  after market exhaust for kawasaki klx 250 13 reg Direct Download speed 5282 Kb/s

  after market exhaust for kawasaki klx 250 13 reg Full Version speed 6162 Kb/s



Kawasaki Exhausts – ZX-6 ZX-10 Zx-14 Exhaust – Slip-ons INSTALLATION MANUAL

0

Filed Under (Kawasaki) by admin on 25-10-2010

download
Our favorite exhaust options for Kawasaki ZX Ninjas – ZX-10,ZX-6r, and the new horsepower king, Zx-14.. Grab your horsepower today. We love Rob Muzzy and Muzzy Exhausts.Going back to Doug Chandler and Scott Russell, Muzzy has been synonomous with Kawasaki and performance – and for years, if you rode Kawasaki,and you were on the podium, Muzzy was on your exhaust. We also feature Arrow and Yoshimura exhausts for your ZX-6R, ZX-10 and ZX-14. We love the sound of a Yosh exhaust on any Kawasaki Ninja. Yoshimura Oval (RS-3) Race Slip-On for Kawasaki ZX14R 2006 The easiest and least expensive way to experience Yoshimura performance is with our Slip-On/Bolt-On lines. Bolt-On style bolts to the O. E. M. mid-pipe Slip-On style with its stainless steel easily attaches to the mid-pipe RS-1 is available where noted Usually, no jetting or re-programming is required and installation is a snap Hindle Stainless Exhaust High Head Pipes – Kawasaki ZX6R-RR 03-04 The worlds lightest stainless steel exhaust system. Increase horsepower and torque throughout the entire rpm range. Lightweight, strong stainless steel header design looks great and weighs less than stock headers. Available in low- and high-mo North Denver News http://northdenvernews.com Powered by Joomla! Generated: 19 October, 2010, 12:28 Hindle Stainless Exhaust Low Head Pipes – Kawasaki ZX9R 00-03 The worlds lightest stainless steel exhaust system. Increase horsepower and torque throughout the entire rpm range. Lightweight, strong stainless steel header design looks great and weighs less than stock headers. Available in low- and high-mo

Incoming search terms:

VESPA GTS 250 i. e. EXHAUST MANIFOLD REPLACEMENT

0

Filed Under (Vespa) by admin on 11-11-2010

download
VE SPA GTS 250 i. e. EXHAUST MANIFOLD REPLACEMENT To replace the exhaust manifold, order part number 872659 as spare part following standard proceedings. OPERATION PROCEDURE The above picture references the old exhaust flange and the replacement exhaust flange kit part number 872659. Replacement Old Page 5 of 16 With the complete exhaust system removed from the vehicle remove the lambda sensors. Refer to page 88 and 89 of your Vespa GTS workshop manual for exhaust removal. Loosen the 13 mm bolt to loosen the clamp. Bolt Remove lambda sensor Page 6 of 16 Remove the header pipe from the exhaust box. Remove the exhaust packing and clamp. Remove exhaust manifold Gasket Clamp Page 7 of 16 Once all packing is removed check and make sure all surfaces are clean. This will help the installation of the exhaust gasket. Install the new clamp supplied with the kit, but do not tighten down at this point. Fit the exhaust gasket onto the new manifold. Push the new exhaust gasket in with the manifold until fitted all the way down to the flange. Check surfaces. Manifold Gasket Clamp Flange Page 8 of 16 Replace the lambda sensor and tighten down to 40- 50 Nm (29.5 -36.8 ft lbs. ) .

Incoming search terms:

SUZUKI M109 1800 cc EXHAUST SYSTEM INSTALLATION MANUAL

0

Filed Under (Suzuki) by admin on 10-11-2010

download
1. Remove the seat and right side fairing cover (with M109 insignia), behind the fuel tank. To remove the fairing, release the plastic peg on top by pushing the center inward and pulling the fairing upwards until the peg releases, remove the M6 button head bolt at the bottom of the fairing. Pull the fairing outward from the rear and upward near the plastic peg to release it. Once it is free from all plastic pegs pull it forward to release it from the bottom of the fuel tank. 2. Remove the right side cover above the exhaust-mounting bracket secured by one M6 button head bolt, retain bolt for later. Remove the chrome steel cover above the exhaust secured by two remaining bolts, (this chrome piece will no longer be used.) Remove the large left rear rubber grommet and flanged steel collar from this chrome piece, to do this press the steel collar out of the rubber grommet first, once the collar is removed push the rubber grommet out of the wire loop on the chrome piece, set aside for later use. 3. Locate the exhaust valve actuator solenoid and harness and disconnect the black 3-prong electrical connector and white 2-prong electrical connector. 4. Remove the socket head bolts securing exhaust flanges to cylinder heads, set these fasteners aside for later use in reassembly. Support the weight of the exhaust system and remove the 2, 8 mm bolts and one 8 mm nut securing the exhaust mounting bracket and exhaust assembly. Keep these fasteners for use later. Remove the stock exhaust system as one complete unit; this includes the stock exhaust bracket, headpipes and muffler, exhaust valve solenoid and cables. 5. The exhaust valve actuator solenoid must now be removed from the stock exhaust-mounting bracket. To perform this, loosen the two nuts securing each cable to the exhaust valve cable-mounting tab, Position A in Figure 1. Make enough slack in the cables so that the ends of the cables’ threaded sheath may be disengaged from the end of the mounting tab. Now remove the two M6 hex head bolts securing the solenoid to the stock exhaust bracket. The stock exhaust mounting bracket, headpipes and muffler and exhaust valve solenoid cables will not be used anymore with the your new Cobra Exhaust System. 6. Remove the dust cover from the solenoid to expose the rotating cam and cables. DO NOT TRY TO ROTATE THE CAM RELATIVE TO THE ACTUATOR SELENOID TO REMOVE THE CABLES; DOING SO MAY DAMAGE THE INTERNAL COMPONENTS OF THE SOLENOID. To remove the cables from the cam, use the slack in the cables obtained in Step 5 to disengage the cable barrels from the cam, see Figure 1. THE DUST COVER WILL NOT BE REINSTALLED. 7. Now prepare the exhaust valve actuator solenoid for reuse. SECURELY HOLD THE CAM TO PREVENT IT FROM ROTATING IN THE SOLENOID. WHILE PREVENTING THE CAM FROM ROTATING, remove the 10 – 32 flange bolt securing it, see Figure 2. Replace the cam with the Cobra supplied cam, BE SURE TO PREVENT THE CAM FROM ROTATING WHEN REINSTALLING THE BOLT, OTHERWISE DAMAGE MAY OCCUR TO THE SOLENOID , see Figure 3. Torque to factory specifications.

Incoming search terms:

Kawasaki Ninja 250 FAQ

0

Filed Under (Kawasaki) by admin on 15-11-2010

download
Am I too small for this motorcycle? Duke – Sun May 14 17:38:31 2000 I’m only about 5’2″ and don’t have a problem, even though I can only touch the ground with the ends of my toes. Once you get a feel for the balance of the bike it’s not hard to keep everything upright. Only place I have trouble is pushing the bike backwards in a parking lot. Usually I just walk the bike (beside it) to where I can get on and get going. How does the EX500 compare to the EX250? Craig M. – Mon May 22 10:23:29 2000 I have both the EX250 and the EX500; both are Y2K models. The 250 is a screamer that performs well and can easily get me into trouble. My only complaints about the 250 are the excessive nose dive when getting on the front brake hard and the skittishness of the rear during high speed cornering. Both are easily corrected with suspension adjustments, I’ve just been too lazy to get the parts and do the work. A bit more wind protection would be great too. The 500 addresses these problems, the diving of the front end (to a degree); the rear’s skittishness and the wind protection. A plus for the 500 is the greater torque and power off the line; it pulls stronger (in my opinion) and will get you into illegal speed territory just a bit quicker than the 250. With greater weight, is has more stability in high speed and windy situations. Insurance is just about the same for both, with the 250 getting the nod for gas mileage. Service requirements are almost identical for both as well, being that they’re both parallel twins, the technology is the virtually the same. The downfalls of the 500: $2K more than the 250 (can do a lot to the 250 with that kind of money); buzzy mirrors, barely useful; heavier weight to have to push around the garage; lesser gas mileage (55-60 MPG; 250 pushes 70 MPG easily); engine is worse than a nervous dog shaking around at idle and at speed (here the 250 is far superior and much smoother). In my opinion, the 500 is a better suited for a larger rider, from a comfort standpoint. I feel I can stretch out a bit more on it than the 250 (I’m 5′ 9″, 160 lbs). The 250′s brakes are better tuned than the 500 and the shifter is much smoother. That may be due to the 3,500 mile difference between the two bikes. Bottom line, both bikes are great, the 250 is now my wife’s ride (mainly) and the 500′s mine (unless she steals the keys away). In time, I’ll make the adjustments to the 250; she doesn’t push it like I do.

Incoming search terms:

SUZUKI M109 1800 cc FRONT/REAR EXHAUST / HEATSHIELD INSTALLATION MANUAL

0

Filed Under (Suzuki) by admin on 15-11-2010

download
1. Remove the seat and right side fairing cover (with M109 insignia), behind the fuel tank. To remove the fairing, release the plastic peg on top by pushing the center inward and pulling the fairing upwards until the peg releases, remove the M6 button head bolt at the bottom of the fairing. Pull the fairing outward from the rear and upward near the plastic peg to release it. Once it is free from all plastic pegs pull it forward to release it from the bottom of the fuel tank. 2. Remove the right side cover above the exhaust-mounting bracket secured by one M6 button head bolt, retain bolt for later. Remove the chrome steel cover above the exhaust secured by two remaining bolts, (this chrome piece will no longer be used.) Remove the large left rear rubber grommet and flanged steel collar from this chrome piece, to do this press the steel collar out of the rubber grommet first, once the collar is removed push the rubber grommet out of the wire loop on the chrome piece, set collar and grommet aside for later use. 3. Locate the exhaust valve actuator solenoid and harness and disconnect the black 3-prong electrical connector and white 2-prong electrical connector. 4. Remove the socket head bolts securing exhaust flanges to cylinder heads, set these fasteners aside for later use in reassembly. Support the weight of the exhaust system and remove the 2, 8 mm bolts and one 8 mm nut securing the exhaust mounting bracket and exhaust assembly. Keep these fasteners for use later. Remove the stock exhaust system as one complete unit; this includes the stock exhaust bracket, headpipes and muffler, exhaust valve actuator solenoid and cables. 5. The exhaust valve actuator solenoid must now be removed from the stock exhaust-mounting bracket. To perform this, loosen the two nuts securing each cable to the exhaust valve cable-mounting tab, Position A in Figure 1. Make enough slack in the cables so that the ends of the cables’ threaded sheath may be disengaged from the end of the mounting tab. Now remove the two M6 hex head bolts securing the solenoid to the stock exhaust bracket. The stock exhaust mounting bracket, headpipes and muffler and exhaust valve solenoid cables will not be used anymore with the your new Cobra Exhaust System

Vespa GTS 250 exhaust system SERVICE INSTRUCTIONS

0

Filed Under (Vespa) by admin on 28-10-2010

download
to replace the exhaust manifold, order part number 872659 as spare part following standard proceedings. OPERATION PROCEDURE The above picture references the old exhaust flange and the replacement exhaust flange kit part number 872659. Replacement Old
Page 5 of 16 With the complete exhaust system removed from the vehicle remove the lambda sensors. Refer to page 88 and 89 of your Vespa GTS workshop manual for exhaust removal. Loosen the 13 mm bolt to loosen the clamp. Bolt Remove lambda sensor
Page 6 of 16 Remove the header pipe from the exhaust box. Remove the exhaust packing and clamp. Remove exhaust manifold Gasket Clamp Page 7 of 16 Once all packing is removed check and make sure all surfaces are clean. This will help the installation of the exhaust gasket. Install the new clamp supplied with the kit, but do not tighten down at this point. Fit the exhaust gasket onto the new manifold. Push the new exhaust gasket in with the manifold until fitted all the way down to the flange

2008 KAWASAKI KX 250 F RACING AND EVOLUTION EXHAUST SYSTEM

0

Filed Under (Kawasaki) by admin on 05-11-2010

download
the Akrapovic Racing and Evolution complete exhaust systems are the flagships of our product lines. They are designed for competition-oriented MX riders who demand maximum performance from their exhaust systems. With their production quality, engine performance improvements and modern Hexagonal muffler design they satisfy the requirements of all riders. The systems are designed for two markets; in the US they are available with an approved spark arrester, and for the EU and other non-US markets they come with a noise damper. New for 2008 is additional chamber that helps to reduce noise emission and provides better power and torque at low rpm range. PERFORMANCE Measurements of the Akrapovic EVOLUTION system on the KAWASAKI KX 250 F (with muffler insert): Power & Torque: The Akrapovic Evolution and Racing systems deliver a performance increase throughout nearly the entire rpm range. It is most pronounced in the bottom and the top of the range. The systems deliver increased torque similar to the power increase. Max. increased power of 0.7 HP was measured at 12260 rpm, while max. power of 34.6 HP was measured at 11400 rpm. CONFIGURATION Akrapovic Racing and Evolution systems are of a recognised Hexagonal off-road form. They differ only in terms of the material of the pipe: we use stainless steel for Racing and titanium for Evolution. The header tube is conical, made from stainless steel (Racing) or titanium (Evolution) with additional chamber. It is jointed with a conical SS/titanium link pipe by a sleeve joint, which is secured with a silicon-shielded spring. The link pipe is welded to the muffler. The inlet cap, due to the method of connection with the link pipe, is made from stainless steel (Racing) or titanium (Evolution), same for the internal perforation. The outlet cap is made of carbon-fiber for evolution and composite polymer for Racing system. The outer sleeve of the muffler is available either made from titanium or carbon fiber. The system is attached to the motorcycle with the Akrapovic carbon fiber clamp. The Akrapovic carbon fiber heat shield is also intended for this system. The system comes with a built-in noise damper for the European and other markets, and an approved spark arrester for the American market, which is marked with a laser engraving

KAWASAKI VULCAN 2000 POWERSHOTS EXHAUST SYSTEM INSTALLATION MANUAL

0

Filed Under (Kawasaki) by admin on 23-12-2010

download
STOCK EXHAUST SYSTEM REMOVAL 1. Remove right side frame cover. 2. If motorcycle is oxygen sensor equipped, remove passenger seat. Remove two bolts securing operator seat and set seat aside. Locate and unplug oxygen sensor connector from wiring harness (Figure 1).(Note wire routing for reassembly). 3. Remove right side floorboard assembly held in place by two bolts (Figure 2). 4. Remove exhaust port flange nuts. 5. Remove flange bolts securing rear muffler to exhaust system mounting bracket. 6. Remove complete exhaust system. Start by removing front head pipe from exhaust port (assistance may be required). Page 1of 4 K400IN Rev. 1.1 KAWASAKI VULCAN 2000 POWERSHOTS EXHAUST SYSTEM Part #18311 Tools required for installations 6mm Allen wrench 8mm 12mm 14mm sockets 3/8″ Ratchet & Extensions 19mm Wrench 9/16 Wrench Brake bleeder & fluid
7. Check condition of stock exhaust gaskets. Replace if damaged or worn. 8. Remove plastic hose clamp securing rear brake hose to swingarm.Save for re-use. 9. Remove brake hose banjo bolt from rear caliper. 10. Slide hose out of loops in swingarm. 11. Remove three bolts holding stock exhaust mounting bracket and slide bracket off end of brake hose. 12. Slide brake hose through loop on new bracket (stamped 357-P) and install to the original mounting bracket location, using three 8mm x 16mm Allen bolts (supplied) (Figure 3). 13. Check condition of sealing washers on banjo bolt and replace if damaged or worn. 14. Slide brake hose through loops on swingarm and reconnect brake hose to caliper. 15. Reinstall plastic clip onto swingarm. 16. Brake system must be bled or brake will not operate correctly.

Incoming search terms:

2008 KAWASAKI KX 250 F SLIP-ON EXHAUST SYSTEM

0

Filed Under (Kawasaki) by admin on 05-11-2010

download
quality, engine performance improvements and modern Hexagonal muffler design they satisfy the requirements of all riders. The systems are designed for two markets; in the US they are available with an approved spark arrester, and for the EU and other non-US markets they come with a noise damper. New for 2008 is additional chamber that helps to reduce noise emission and provides better power and torque at low rpm range. PERFORMANCE Measurements of the Akrapovic EVOLUTION system on the KAWASAKI KX 250 F (with muffler insert): Power & Torque: The Akrapovic Evolution and Racing systems deliver a performance increase throughout nearly the entire rpm range. It is most pronounced in the bottom and the top of the range. The systems deliver increased torque similar to the power increase. Max. increased power of 0.7 HP was measured at 12260 rpm, while max. power of 34.6 HP was measured at 11400 rpm. CONFIGURATION Akrapovic Racing and Evolution systems are of a recognised Hexagonal off-road form. They differ only in terms of the material of the pipe: we use stainless steel for Racing and titanium for Evolution. The header tube is conical, made from stainless steel (Racing) or titanium (Evolution) with additional chamber. It is jointed with a conical SS/titanium link pipe by a sleeve joint, which is secured with a silicon-shielded spring. The link pipe is welded to the muffler. The inlet cap, due to the method of connection with the link pipe, is made from stainless steel (Racing) or titanium (Evolution), same for the internal perforation. The outlet cap is made of carbon-fiber for evolution and composite polymer for Racing system. The outer sleeve of the muffler is available either made from titanium or carbon fiber. The system is attached to the motorcycle with the Akrapovic carbon fiber clamp. The Akrapovic carbon fiber heat shield is also intended for this system. The system comes with a built-in noise damper for the European and other markets, and an approved spark arrester for the American market, which is marked with a laser engraving.

Kawasaki ZX-9R Ninja TiForce exhaust system Installation Instructions

0

Filed Under (Kawasaki) by admin on 07-05-2012

download
1. Remove the lower fairing. Remove thelower radiator mounting bolts, loosen the upper bolts and pivot the radiator forward to provide access to the exhaust nuts (flange nuts). Remove the oil cooler mounting bolts and pivot the oil cooler forward to provide access. 2. Remove the existing exhaust system and save the flange nuts for reuse. Save the stock exhaust can mounting bolt and nut for reuse as well. 3. Inspect the exhaust gaskets. Replace if necessary. 4. Assemble the head pipes 1 (blue), 2 (red), 3 (yellow), and 4 (green) by matching the joints of the same color to the pair of front Y-pipes. Do not install the exhaust springs at this time. 5. 2000 through 2002 models ONLY!!! Place a billet aluminum exhaust port centering flange Z on each TiForce headpipe -see figure 3 for details. 6. Attachthe assembled head pipe sections to the exhaust ports, but do not tighten the flange nuts fully, allowing for some adjustment in the remaining steps. Reuse the flange nuts saved from step 2 above. Make sure the ends of the headpipes fit flush and snug in the ports and centering flanges Z before tightening (’00-’02 ONLY). 7. Install the S-Bend to the front section of the headpipes and two Y-pipes. 8. Go back and retighten the head pipe flange nuts per factory specifications -make sure the headpipes and flanges Z are centered in each port (’00-’02 ONLY!!! ) . 9. Slide the TiForce end can into place. 10. Loosely attach the two rubber bands, stainless steel bands K, and stay / hanger G to the end can using the supplied 6mm hardware H. See figure 1. 11. Place the bands approximately 108 mm from the edge of the end can. See figure 2. 12. Using the stock provided mounting point on the passenger footpeg, and using the stock mounting bolt, mount the end can loosely, allowing for some adjustment. Insert the stock mounting bolt through the stay / hanger G. 13. Attach the supplied springs to all the joints, starting from the headpipes and working back to the end can. 14. Make sure the exhaust system is free and clear, if necessary jiggle the system to adjust for proper clearance. 15. Carefully align the two stainless bands K so that they are parallel to each other, and spaced properly on the can (refer to step 11 /figure 2), then tighten the 6mm hardware H and the stock mounting bolt hardware. Make sure that the rubber pads fully cover the band(s). USE CAUTIONWHEN TIGHTENING THE 6MM HARDWARE AND THE TWO BANDS SO AS NOT TO CRUSH OR DISTORT THE SLEEVE OF THE CAN.

Incoming search terms: