ajust carbs on 98 zx9r

You search Auto repair manual PDF ajust carbs on 98 zx9r, if there are search results will appear below. If search results do not exist, please search by others keyword.



  ajust carbs on 98 zx9r Direct Download speed 5282 Kb/s

  ajust carbs on 98 zx9r Full Version speed 6162 Kb/s



2002-2003 KAWASAKI ZX9R OGGY KNOBB KIT.

0

Filed Under (Kawasaki) by admin on 05-11-2010

download
Congratulations on purchasing your Oggy Knobb kit. It has been designed to reduce damage to your motorcycle from impact and abrasion by the road surface in an accident. We have used only the highest quality materials to achieve the strength and appearance your investment deserves. Carefully read the fitting instructions below and check you kit contents before starting installation. If you are unsure or not confident about installing Oggy Knobbs yourself, see your mechanic. Instructions-Left Side: 1. Remove the engine mounting bolt, the position of which can be seen in the photo above. There is captured nut on the engine which must stay in place. 2. Fit the Oggy Knobb assembly with the thick washer behind the Oggy Knobb. 3. Tighten the bolt securely to manufacturer’s specifications. 4. On the right side, repeat steps 1 to 3.

Kawasaki 900 / 1100 Engine Removal and Installation

0

Filed Under (Kawasaki) by admin on 01-05-2012

download
1.1 (Above) Remove the two retaining straps, disconnect the battery and remove it from the hull. Disconnect the negative (black) cable first, then the positive (red). Step 2 Intake Removal 2.1 (Below) Remove the eight 10mm bolts securing the flame arrestor cover to the base and remove it. 2.2 (Below) Pull out the flame arrestor screens. 2.3 (Below) Remove the six 10mm bolts securing the flame arrestor base and carbs to the manifold and remove the base. 2.4 (Below) Loosen the gas tank cap to relieve pressure. Be sure the fuel switch is turned to the “OFF” position, and be aware of any fuel that may spill from the hoses. Make sure the hull is clear of any gasoline fumes before continuing work, especially with power tools. Remove the pulse lines from the block, and the three oil lines from the carbs. Move the carbs aside in the hull. 2.5 (Below) Remove the 18 10mm nuts from the studs securing the intake manifold to the engine and remove the manifold

Performance Starts Here RACING CARBURETORS

0

Filed Under (Mikuni) by admin on 31-10-2010

download
Mikuni RS Series Radial Flat Slide carburetors represent the first ever aftermarket true high performance carbs offered to the racing public. Designated the RS for radial slide design, these carbs feature such innovations as: large 34, 36 or 38mm smoothbores, excellent throttle response and streetability, adjustable accelerator pump system, lighter more compact design, quick change needle clip, cam-lock carb synchronizing, horsepower improvement of 25% to 30% and competition priced. • Starter System: Provides fuel enrichment for cold engine starting. • Accelerator Pump Adjust Screws: Sets on and off operation of accelerator pump in relation to throttle slide position. • Adjustable Accelerator Pump: Squirts fuel into carburetor venturi when throttle is opened to improve engine response. • Idle Adjustment Screw: Controls engine idle speed. • Throttle Return Spring: A choice of positioning pegs allows adjustment of spring tension. • Genuine Mikuni Jets: Provide for precise fuel metering. • Pilot Air Jet: in conjunction with the Pilot Fuel Screw for tuning of mixture at idle to 1/4 throttle. • Float Bowl Vent: Allows atmospheric pressure into float bowl for fuel flow. • Smooth Throttle Bore/Venturi: Produces the optimum air and fuel mixture flow at all RPMs. • Jet Needle Clip: Has easy adjustment feature for quick tuning. • Accelerator Pump Spray Nozzle: Shoots fuel directly into the intake tract for immediate engine response. • Flat Throttle Valve Design: Provides the strongest signal for precise and instantaneous throttle response

YAMAHA V-STAR 1100 HYPERCHARGER AIRCLEANER INSTALLATION MANUAL

0

Filed Under (Yamaha) by admin on 09-11-2010

download
STEP 1 Remove the driver and passenger seats from the bike. Remove the negative battery cable from the battery and tuck it out of the way to reduce the possibility of sparks. STEP 2 Remove the two rear tank mounting bolts. Remove the plastic tank mounting snap stud. (Push in on the center of it to release). Slide the tank back to expose the top of the engine. Make sure the tank is solidly in place so it does not fall! You may remove the tank completely from the bike if you’re not certain the tank will stay in place while you are performing this installation. STEP 3 Remove the stock air cleaner cover, element, and backing plate. Twarrants that any Küryakyn product sold hereunder, if properly installed, maintained and operated under normal conditions, shall be free from any defects in materials and workmanship for a period of one (1) year from the date the Küryakyn products are sold to the customer. CONSEQUENTIAL DAMAGES: Küryakyn shall not be liable for any consequential or incidental damages. ABOUTOURCA TA LOG You’ll find all our innovations for H-D, GL and Metric Cruisers in our annual catalogs. Order online today-select the “CATALOGS” icon. Each Küryakyn™ product comes with a Proof-of-Purchase good for a complimentary catalog. Details in packaging. Be sure to ask your local dealer about other Küryakynproducts, the motorcycle parts and accessories designed for riders by riders. ©2003 Küryakyn USA™All Rights reserved. STEP 4 See PIC. 1and PIC.2. Remove the grommet from the bracket. STEP 5 Placing your long handled Phillips screwdriver as shown in PIC.3, loosen the clamp on the air duct and remove the duct. Remove the clamp from the duct— it will be reused. Now is a good time to proceed with rejetting of the carburetors. Consult your factory service manual for this procedure. We have supplied jets to cover most common applications. Jetting Recommendations: See FIG. 1for jet locations. With stock exhaust or Cobra Slip-On Mufflers • 1.2 Pilot Air Bleeds in both carbs • One .020 shim added to raise each needle • 122.5 Main Jet in the front cylinder’s carb • 120 Main Jet in the rear cylinder’s carb • Pilot Mixture Screw (PMS) 2 turns out from lightly bottomed With Vance & Hines, Samson, or open “Drag” pipes • 1.2 Pilot Air Bleeds in both carbs • One .020 shim added to raise each needle • 125 Main Jet in the front cylinder’s carb • 122.5 Main Jet in the rear cylinder’s carb • Pilot Mixture Screw (PMS) 2 turns out from lightly bottomed NOTES 1. The factory installed plug covering the PMS will have to be removed in order to access the screw. 2. Because the float bowl screws are easily damage during removal, we have included 8 replacement float bowl screws with socket heads, just in case they are needed. BE SURE TO VENT THE FLOAT BOWLS TO THE BACK OF THE HYPERCHARGER — THIS IS NECESSARY FOR BEST DRIVABILITY AND MAXIMUM PERFORMANCE!!!! (See Step 12.) STEP 6 See PIC.4. Insert both flanges of the rubber air duct through the opening in the mounting bracket. Place the Stock duct clamp on the new intake duct — the clamp screw should face forward.

Yamaha V-Star 1100 Jetting the Carburetors INSTALLATION MANUAL

0

Filed Under (Yamaha) by admin on 11-03-2012

download
Remove air filter housing Remove the seat or seats Disconnect Fuel Lines (also the vapor line from tank to charcoal canister on California models) Disconnect instrument connectors from the fuel tank Remove fuel tank Remove air box Disconnect TPS and heater connectors Remove chrome carb cover Disconnect Fuel Lines Remove rubber carb elbows Disconnect throttle cables from carbs Remove the carbs Perform the jetting 1. Remove the Chrome air filter housing. To remove the chrome dog-dish (air filter housing) from the right side of the bike, you will need to remove the two mounting bolts and loosen the clamp that holds the air duct to the back of the housing. You will need a 5 mm Allen wrench and a #2 Philips screwdriver. 2. Remove the seats. This can be accomplished by using a 5 mm Allen wrench and removing the Allen head bolt from just behind the rear seat and the bolt just behind the front seat. Pulling up and back will free the seats. One smooth motion will do it. 3. Gain access to the dashboard plug and unplug it (It is white) Note: Your trip odometer will lose its count, please record the number if you wish to save your current mileage for this tank of gas. Figure A shows the three plastic rivets that need to be removed to gain access to the dashboard plug. Using your Philips head screwdriver, press the small circle in the middle of the rivets down… a click is felt. Remove the rivets by hand. You have freed the cover and you may lift it up to expose the electrical connector that needs to be unplugged. Figure B shows the plug

Mikuni VM 36 mm Round Slide Carburetor Instalation

0

Filed Under (Mikuni) by admin on 31-10-2010

download
Carbs fit perfectly in the stock carb mounting boots for 1980 and up XS 650s that came with the chrome *bit of tin” vacuum chamber tops. Air filters extend to stock battery box.The custom 2 into 1 throttle cable comes made to fit with the stock Yamaha throttle housing! This bike idles crisp and clean, has instant throttle response and pulls hard from idle to redline, no bog, or loading up, even with the bone stock exhaust system. Very impressive performance over the stock worn out 34mm CV carbs

Kawasaki Exhausts – ZX-6 ZX-10 Zx-14 Exhaust – Slip-ons INSTALLATION MANUAL

0

Filed Under (Kawasaki) by admin on 25-10-2010

download
Our favorite exhaust options for Kawasaki ZX Ninjas – ZX-10,ZX-6r, and the new horsepower king, Zx-14.. Grab your horsepower today. We love Rob Muzzy and Muzzy Exhausts.Going back to Doug Chandler and Scott Russell, Muzzy has been synonomous with Kawasaki and performance – and for years, if you rode Kawasaki,and you were on the podium, Muzzy was on your exhaust. We also feature Arrow and Yoshimura exhausts for your ZX-6R, ZX-10 and ZX-14. We love the sound of a Yosh exhaust on any Kawasaki Ninja. Yoshimura Oval (RS-3) Race Slip-On for Kawasaki ZX14R 2006 The easiest and least expensive way to experience Yoshimura performance is with our Slip-On/Bolt-On lines. Bolt-On style bolts to the O. E. M. mid-pipe Slip-On style with its stainless steel easily attaches to the mid-pipe RS-1 is available where noted Usually, no jetting or re-programming is required and installation is a snap Hindle Stainless Exhaust High Head Pipes – Kawasaki ZX6R-RR 03-04 The worlds lightest stainless steel exhaust system. Increase horsepower and torque throughout the entire rpm range. Lightweight, strong stainless steel header design looks great and weighs less than stock headers. Available in low- and high-mo North Denver News http://northdenvernews.com Powered by Joomla! Generated: 19 October, 2010, 12:28 Hindle Stainless Exhaust Low Head Pipes – Kawasaki ZX9R 00-03 The worlds lightest stainless steel exhaust system. Increase horsepower and torque throughout the entire rpm range. Lightweight, strong stainless steel header design looks great and weighs less than stock headers. Available in low- and high-mo

Incoming search terms:

HONDA GL1100 Manifold Cover Installation Manual

0

Filed Under (Honda) by admin on 04-03-2011

download
Note: Read instructions carefully before installing. 1. Start with right side. Remove (2) screws and washers from each manifold tube base. NOTE: Save this hardware it will be reused. 2. Remove (4) screws and washers that hold chrome wire guide to carbs. 3. Apply a small amount of grease to the No. 10 washers (4). This will help to hold them in place on installation. 4. Place the No. 10 washers over the threaded holes in the carb base. 5. Reinstall the OEM wire guide and carefully insert 20 mm screws and lock washers. NOTE: The screws DO NOT go through the tube on the manifold covers. 6. Sandwich the tabs on the manifold cover between the carb top and the wire guide. Finger tight the screws. NOTE: Route spark plug wires OVER THE TOP of the wire guide. 7. Lift bottom of manifold cover and insert aluminum washers removed in step 1. Put smooth of washers toward manifold. You may have to use small amount of grease on these washers also to position them. 8. Position manifold cover and reinstall (2) OEM screws removed in step 1 9. REPEAT STEPS FOR THE OTHER SIDE.

Incoming search terms:

Balancing Honda GL1500 Carburetor Manual

0

Filed Under (Honda) by admin on 08-04-2011

download
First pry off the plastic clip covering the screw as in the first picture. Note the type of screw used, as shown in the third picture. You must put this one back in the right place. Tip; When refitting this clip later on, a bit of Blutack or similar will stop it falling off and getting lost. Pull the L piece trim away, taking care not to break the tab shown in the fifth picture Now pry off the small black plastic cover at the rear of the running light. Blutack will be a good idea here as well when refitting the cover. The owner of this GL1500 didn’t use it and the cover on each side of the Goldwing got lost, which is why you can’t see them in the pictures. Note the type of screw used here as well, same as the one mentioned earlier. The third picture shows the two normal Phillips screws at the front of the running light, remove them. Remove the running light and pull the lower fairing panel away Remove the rubber plug from the right side fan. The adjuster screw for balancing the carbs is about 6″ behind and up, and hard to see. I removed the fan so I could get the camera in and the second picture shows the adjuster screw

Harley-Davidson Carburetors TUNING INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 07-02-2011

download
CARBURETOR REMOVAL Edelbrock recommends consulting an authorized service manual for make, model and year of motorcycle before disassembly of stock parts. 1. Turn fuel valve off before getting started. 2. Disconnect battery to eliminate the possibility of sparks or accidentally engaging the starter. 3. Remove air cleaner assembly. 4. Disconnect choke cable from its bracket. 5. Disconnect fuel line and vacuum lines from carburetor. 6. Gently remove carburetor from manifold. NOTE: For removal of CV style carbs, Edelbrock recommends the carb be gently wiggled from side to side (not up and down) while pulling to get carb out of manifold. MANIFOLD REQUIREMENTS Edelbrock Quick Kits and Complete kits are designed to work with the stock manifold that was OE on your engine. Some aftermarket manifolds will also work with Edelbrock carburetors. S&S “E” Series and Screamin’ Eagle flange mount manifolds will work with Edelbrock flange style carburetors. It is also recommended the manifold being used closely matches the venturi of the carburetor. BIKE PREPARATION 1. Once stock carburetor and air cleaner have been removed, inspect manifold grommet (CV manifolds only) for tears, nicks or cuts. Replace grommet, if damaged. Stuff a clean dry rag into manifold until carb is installed to keep any debris out of engine. 2. Remove old fuel line and vacuum line (if equipped) and install supplied fuel line and vacuum line