animal_feed mail

You search Auto repair manual PDF animal_feed mail, if there are search results will appear below. If search results do not exist, please search by others keyword.





KTM 3V TURBO DRIVE MODEL 9808T KNEE FEED Installation and Removal Manual

0

Filed Under (KTM) by admin on 28-01-2012

download
Gather together the following items that you will need to complete this installation. a) lathe b) 3/8″ electric hand drill c) 9/32″ diameter transfer punch SERVO Turbo Drive Model 9808T Page 2 d) .4375 drill, 3/16″ drill, #7 drill e) 1/4-20 tap f) 3/4″ socket wrench g) set of inch hex wrenches h) clean shop rag Step 2: Clean the power feed mounting area completely. Step 3: Remove the drive clutch nut and the drive clutch from the elevating jack shaft. Step 4: Remove the dial nut, dial, and dial carrier. Keep the dial for reuse later. Step 5: Remove the existing bearing retainer. Keep the screws for reuse later. Step 6: Pull jack shaft out of knee. Hold inboard end up while removing to avoid damage to the pinion gear. Step 7: Press the bearing off the jack shaft. Step 8: Drill and ream the end of the jack shaft .4375″ diameter by 13/16″ deep. The .4375″ dia. must be concentric to the shaft O.D. within .002″ T.I.R. Chamfer 1/32″ x 1/2″ diameter. For best results, machining should be done in a lathe. Step 9: Place the shaft extension #6975 into the end of the jack shaft. Finish drill 3/16″ diameter through the shaft and pin the extension with the 3/16″ diameter x 5/8″ long roll pin. File smooth. Step 10: Reassemble and replace the jack shaft in the machine. Step 11: Replace the existing bearing retainer with #57904 retainer provided. Secure using existing screws. Step 12: Slip spacer #5426 and bearing race #1616 onto the jack shaft. Slide the adaptor #0771 over the bearing race and locate against front of the knee.

Incoming search terms:

HARLEY DAVIDSON FLSTF TURN SIGNAL RELOCATION KIT REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 24-02-2011

download
REMOVAL 1. Remove seat according to the instructions in the Service Manual. To prevent accidental vehicle start-up, which could cause death or serious injury, disconnect battery cables (negative (-) cable first) before proceeding. (00307a) Disconnect negative (-) battery cable first. If positive (+) cable should contact ground with negative (-) cable connected, the resulting sparks can cause a battery explosion, which could result in death or serious injury. (00049a) 2. See Figure 1. Disconnect battery cables, negative (-) cable first. 2 1 is03242 1. Negative (-) cable 2. Tail lamp connector Figure 1. Negative Battery Cable and Tail Lamp Connector 3. See Figure 2. Remove two screws and tail lamp lens (1) from base (2). 2 1 is03243 1. Tail lamp lens 2. Tail lamp base Figure 2. Remove Tail Lamp Lens 4. See Figure 3. Using a Terminal Pick Tool (1), depress locking tabs and disconnect turn signal connectors (2- place) (2, 3) from circuit board. 5. Feed turn signal wiring and connector through opening in circuit board assembly and into rear wheel area. 6. See Figure 4. Remove turn signal wiring (1, 2) from clips (3) under rear of fender INSTALLATION NOTE Proper installation of kit requires that tasks be completed for one side of the motorcycle first before continuing to the opposite side. Route Turn Signal Wiring Through Rear Fender and Support 1. See Figure 5. Remove three rear screws (1) from fender support (2). 2. Loosen, but do not remove two front screws (3) from fender support. 1 3 2 is03285 1. Screw, rear (3) 2. Fender support 3. Screw, front (2) Figure 5. Fender Support Screws and Fender Support 3. Pull fender support away from rear fender to gain access to turn signal mount. 4. Remove stock screw and washer from turn signal mount. 5. See Figure 7. Pull turn signal (B) and turn signal mount (A) away from fender support. 6. Remove turn signal and wires from vehicle by routing turn signal wiring and connector through holes in rear fender and fender support. Gently guide wires through holes to ensure they do not get damaged. Feed Wiring and Install Relocation Bracket 1. See Figure 6. Feed turn signal wiring and connector through middle hole in turn signal relocation bracket and under rear of fender support. 1 is04635 1. Wire harness Figure 6. Wire Harness Routing 2. See Figure 7. Insert stock screw and washer through rear hole of relocation bracket (1) and turn signal mount (A). 3. Thread screw into turn signal (B). Tighten to 12-16 ft-lbs (16.3-21.7 Nm). 4. Align relocation bracket (1) with rear of fender support and install with screw (2) and nut (3) from kit. Tighten nut to 12-16 ft-lbs (16.3-21.7 Nm). Complete Turn Signal Relocation Wiring 1. See Figure 5. Install one rear screw (1) to hold fender support in place while routing wiring. Install screw snugly but do not fully tighten

HARLEY DAVIDSON XL PREMIUM OIL COOLER KIT REMOVAL AND INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 29-01-2011

download
1. Refer to Owners Manual to drain engine oil and remove oil filter. 2. See Figure 1. Remove oil feed hose (1) from oil pump. 3. Remove oil feed hose fitting from engine crankcase. Discard oil feed hose. INSTALLATION 1. See Figure 2 and Table 1. Apply Hylomar Gasket and Thread Sealant to threads of fitting (1) and install fitting to oil pump. 2. Apply Hylomar Gasket and Thread Sealant to threads of fitting (1) and install fitting to crankcase. 3. Tighten fittings to 55-65 in-lbs (6.2-7.4 Nm) . 1 2 3 1 is04015 1. Fitting 2. Oil Hose Cooler Supply 3. Oil Hose Cooler Return Figure 2. Oil Hose Cooler Return and Supply Assmeblies 4. Loosely install oil cooler return hose assembly (3) to crankcase fitting. 5. Loosely install oil cooler supply hose assembly (2) to oil pump fitting. 6. See Figure 3 for proper oil hose routing. The oil supply hose (1) should be the upper hose and the oil return hose (2) the lower hose 1 2 is04018 1. Oil Supply Hose 2. Oil Return Hose Figure 3. Oil Cooler Hose Routing 7. Remove two existing clips holding the clutch cable and wire harness from the left frame downtube. 8. See Figure 4 and Table 1. Position oil cooler clamps (7) in approximately the same position as the clips that were removed from the frame downtube. 9. Loosely attach oil cooler (4) to the clamps (7) using screws (9) and nuts (8). 10. Attach oil return hose (3) to the inboard connection of oil cooler (4) with worm clamp (5).

HARLEY DAVIDSON BRAIDED OIL HOSES INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 04-04-2011

download
INSTALLATION To prevent accidental vehicle start-up, which could cause death or serious injury, disconnect negative (-) battery cable before proceeding. (00048a) 1. Disconnect battery negative cable. 2. Drain engine oil according to Service Manual instructions. 3. Removing the rear exhaust pipe may aid in giving access to the oil lines and fittings. If necessary, remove the rear exhaust pipe according to Service Manual instructions. 4. See Figure 5 and Figure 1 for description and location of the three oil hoses that are replaced with the braided hoses in this kit. Remove the original equipment oil feed, return and vent lines. 5. See Figure 2. Remove and discard the original hex threaded quick disconnect fittings (1), (2) and (3) at the engine for each of the hoses removed in Step 4. To remove the fittings, turn the hex in a counterclockwise direction until free. 6. See Figure 5. Install the threaded adapter from the kit onto the corresponding oil line. The adapters for the return and vent lines are the same size. The adapter for the feed line is larger in size. Coat the male threads of the adapters with Loctite 565 thread sealant. NOTE Be sure to install hoses on the correct fittings. If you mix up the hoses, you will change the direction of the engine oil flow, causing severe engine damage. 2 3 1 is04165 1. Oil Return Hose 2. Oil Feed Hose 3. Oil Vent Hose Figure 1. Installed Oil Hoses

Incoming search terms:

HARLEY DAVIDSON LED FUEL GAUGE KIT REMOVAL AND INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 29-01-2011

download
Removing the Analog Fuel Gauge NOTE The fuel gauge wires are routed through a tube in the fuel tank, and are secured by a clip at the bottom of the tank and, on some models, a clamp on the frame. Open the clip and clamp as needed, and be sure there is enough slack in the wires to be able to lift out the gauge. 1. At the bottom left side of the fuel tank, bend back the flexible clip slightly to free the fuel gauge conduit. Open the harness clamp on the frame if necessary to free the conduit. Gently pull on the conduit to draw the Multilock connector [117] out of the tunnel. 2. See Figure 2. Depress the pin on the socket terminal side of the connector, and pull apart the pin and socket halves. 3. See Appendix B in an appropriate Service Manual. Use a pick (Snap-On TT600-3 or equivalent) to remove the terminals or clip off the wires. Remove and discard the fuel gauge. 4. For Carbureted Models: See Figure 2. Remove the fuel gauge by firmly grasping and carefully pulling up (do NOT twist) on the gauge just far enough to free it from the fuel tank. Disconnect the two sending unit connectors. Feed the conduit and two wires up through the tube while removing the gauge. Remove and discard the fuel gauge. For Fuel-Injected Models: See Figure 2. Remove the fuel gauge by firmly grasping and carefully pulling up (do NOT twist) on the gauge to free it from the fuel tank. Feed the conduit and three wires up through the tube while removing the gauge. Remove and discard the fuel gauge. 5. Remove and discard the rubber gasket. INSTALLATION For Kit Numbers 75084-04B or 75237-03B 1. See Figure 2. Assemble the new gasket (3) to the LED fuel gauge (1) from the kit. Install the gasket so the flat side contacts the edge of the gauge. 2. See Figure 1. Use three of the Phillips-head screws and washers from the kit to connect the wires as follows: Fasten the Orange wire (1) ring terminal to the gauge connection marked “12V and “O” with a screw and washer. Fasten the Black wire (2) ring terminal to the connection marked “GND” and “BK” with a screw and washer. Fasten the Yellow/White wire (3) ring terminal to the connection marked “Y/W” with a screw and washer. 3. See Figure 2. While carefully lowering the fuel gauge, feed the wire harness (2) down into the drain tube until the three short (Orange, Black, Yellow/White) wires exit the hole at the bottom of the fuel tank. Gently pull the wires to remove slack while installing the gauge to the fuel tank. Do not twist the gauge during installation. Hold the gauge firmly and press down until it snaps into place

Incoming search terms:

Harley-Davidson feuling Adjustable Pushrods Installation Instructions

0

Filed Under (Harley Davidson) by admin on 22-04-2012

download
1. Refer to the proper factory service manual for your model and year of engine, for removal of existing pushrods. 2. The Feuling pushrods are designed with a small adjustment parameter for rigidity creating maximum lift – These are not quick install pushrods and may require the removal of the lifter blocks and or loosing of the breathers/rocker arms supports. When loosening the rocker arm supports always remove the breather bolts first. 3. Clean and inspect each new Feuling pushrod including center oil hole 4. Feuling pushrods are marked Intake and Exhaust. The shorter pushrods are Intake and the longer pushrods Exhaust 5. Feuling recommends using new O-rings and gaskets where applicable to prevent oil leaks
6. Always pump up hydraulic lifters before installing them. Use an oil squirt can to fill the lifter with oil through the feed hole on the side of the lifter, push oil through the feed hole until the air bubbles are gone. If needed work the oil back and forth through the feed hole and pushrod seat with the squirt can. Light weight oil can be helpful. 7. Assemble and adjust one cylinder at a time, the servicing cylinder needs to be on TDC of compression stroke so the cam lobes are at their lowest point 8. Install pushrods into proper locations with the adjusting side of the pushrod down, towards the lifter. Slide the pushrods through the pushrod covers up into the rocker housing and set the pushrod on the seat of the lifter. We recommend filling the pushrods with oil then maneuver the pushrod up into the rocker arm seat. 9. Torque rocker arm housings and breathers to factory torque spec’s 10. See the instructions for your lifters for the proper adjustment. All Feuling hydraulic lifters run best at . 090″ – . 100″ of crush.

2010 Toyota Motorsports/ TRD USA Contingency Award Program

0

Filed Under (Toyota Manuals) by admin on 29-09-2011

download
To enroll in the program, complete the registration form included in the enclosed material and mail, fax or e-mail it to TRD per the instructions at the bottom of the form. Contact personnel are listed on the attached 2010 Contingency Award Guidelines sheets. These people are available to assist you throughout the year. Parts Ordering: If you are planning to order Toyota parts during 2010 you must supply us with your Visa or Master Card credit card number at the time you register in the program. There is a line on the registration form for this number. See the attached Parts Ordering Guidelines for detailed information on how to order parts. TRD is looking forward to working with each of you, and we wish you a very successful year with your racing program

Incoming search terms:

Mikuni HSR 42/ 45 Installation Instructions

0

Filed Under (Mikuni) by admin on 31-10-2010

download
To install, remove the stock carb per Yamaha shop manual procedures. Remove stock throttle cables. Install Mikuni HSR carb into intake manifold and tighten manifold clamp. Install new HSR series throttle cables and adjust cable slack per Yamaha shop manual procedures. Hook fuel line to HSR carb and fasten clamp.* Start motorcycle and fine tune HSR carb for proper running per supplied Mikuni tuning manual. *NOTE: Mikuni HSR series carburetors are designed for gravity-feed fuel systems. You should bypass your stock fuel pump and directly feed your HSR carb right from the fuel petcock. We have noted, though, that you may not be able to get good fuel flow from your Road Star fuel tank in low-fuel situations. You may run your stock fuel pump with the HSR carb, but to do so requires the purchase and installation of an adjustable fuel pressure regulator (set at ½ to 1 lb. of pressure). These are available from most auto parts stores. The stock carb has 2 wires running to the lower rear of the float bowl , these were for a carb warmer, they are not used in this application. Unplug these wires at the main wire harness and retain with your stock carb. The Road Star ignition system uses data from the stock throttle position sensor (TPS) to manage your ignition timing. It is necessary to give the bike this information. You may do so by removing the TPS sensor from the stock carb, leaving it plugged into the main wire harness (the sensor must be fixed to a closed-throttle position), or you may locate the plug for the TPS on the main wire harness and test the leads – you will find one ground, one with .5V and one with 1.5V. Connect the 1.5V to the ground and this will give the bike the same information as stock fully closed throttle.

Incoming search terms:

BMW Motorcycle R1100 RT R1100 RS R850/ 1100 GS R850/ 1100R Repair Manual

0

Filed Under (BMW) by admin on 18-11-2010

download
Engine Connection Nm Nm Oil filter Oil filter 11 11 Oil drain plug 32 32 Oil pump Mesh filter basket to engine block 9 9 Oil pump cover 9 9 Pressure relief valve 35 35 Oil pressure switch 30 30 Oil cooler Oil cooler pipe to engine block 10 10 Cooling oil line – banjo screw 25 25 Cooling oil line – banjo screw with oil vent valve 25 25 Oil lines to oil cooler 25 – Oil cooler to holder 9 9 Oil cooler return line to engine block 35 35 Oil cooler feed line to frame 20 20 Oil cooler feed line to engine block 25 25 Screw-in union for oil cooler connection at engine block 35 35 Clean threads and apply Loctite 603 to inner and outer threads and in the contact face area Oil cooler hose at oil thermostat – 40 Cylinders Tightening sequence M 8 screw 20 20 M 6 screw 9 9 Chain guide rail pivot screw 18 18 Timing chain Chain tensioner 32 32 Connecting rod Big end cap Joint torque 20 20 Additional wrench angle 80° Crankcase Tightening sequence: M 10 screw (oiled) 45 45 M 8 screw (oiled) 20 20 M 6 screw Engine electrical system Connection Nm Nm Starter motor to engine 20 20 Starter cover to gearbox housing 7 – Positive lead to starter motor 10 10 Alternator to alternator support cover 20 20 Tensioning and retaining strap at alternator 20 20 Spacer at alternator 20 20 Positive lead to alternator 15 15 Belt pulley at alternator 50 50 Belt pulley to crankshaft 50 50 Poly-V belt preload 8 8 Spark plug 20 20 13 Fuel preparation and control Temperature sensor on engine block 25 25 16 Fuel tank and lines Fuel tank to rear frame 22 22 Fuel pump assembly to tank 6 6 18 Exhaust system Muffler to footrest 35 35 Manifold to cylinder head (with strap) 22 22 (with jacket pipe) 18 18 Muffler to support plate for center stand 20 20 Clip on muffler 50 50 Grease clamping face with Never Seez Oxygen sensor (lambda probe) to muffler 55 55 Grease with Never Seez

Incoming search terms:

MODEL 8100 HID/ HALOGEN MOTORCYCLE HEADLIGHT INSTALLATION

0

Filed Under (Tips and Review) by admin on 29-11-2010

download
1) Remove seat. 2) Refer to service manual to locate the following wires: An ignition signal that has power while the ignition is in the “ON” position. Terminal 30 on start relay . A “CRANK” signal (start signal) that has power while the starter motor is being activated. Terminal 86 on start relay . 3) Locate a mounting position for the module that will fit in front of or next to the battery. DO NOT MOUNT the module until all connections to the module have been made. 4) Verify the operation of the ignition and crank signals using the voltmeter or test light. Disconnect battery and make the following connections: • Connect the Blue wire from the lamp module to the ignition feed wire Terminal 30 on start relay . • Connect the Grey wire from the lamp module to the starter crank feed Terminal 86 on start relay . • Connect the Red wire from the module to one end of the fuse harness provided in the kit. • Crimp a ring terminal to the other end of the fuse harness (for connection the POSITIVE battery terminal) . • Crimp a ring terminal to the Black wire from the module. This will need to be routed to the NEGATIVE terminal of the battery • Do not in any way (lengthened or shortened) . Ensure that the ballast is close enough to the lamp to use the length of cable provided. 5) Securely mount ballast in chosen location. Plug the 2 wire sealed connector (RED AND BLACK 16 AWG WIRES) to the ballast. Route the Red and Black wires along the frame, and follow the harness under the fuel tank (recommended) to the battery compartment. Connect the Orange wire from the lamp module to the red wire from the ballast using connector. Crimp ring terminal to black wire coming from the ballast, and connect to the NEGATIVE battery terminal. • IT IS NOT RECOMMENDED THAT THE BALLAST BE MOUNTED IN CLOSE PROXIMITY TO ECU OR FUEL INJECTION WIRING. • Do not mount near sources of high heat (i.e. Cylinder head or exhaust manifold) . • Do not mount in a location where there is a possibility of mechanical interference from moving parts (i.e. Steering components or linkage) . • There is a 3-foot length of cable provided for connection between the BALLAST and the HID LAMP. This cable MUST NOT be modified in any way (lengthened or shortened) . Ensure that the ballast is close enough to the lamp to use the length of cable provided

Incoming search terms: