are after market atv carburators any good

You search Auto repair manual PDF are after market atv carburators any good, if there are search results will appear below. If search results do not exist, please search by others keyword.



  are after market atv carburators any good Direct Download speed 5282 Kb/s

  are after market atv carburators any good Full Version speed 6162 Kb/s



Baja BA 250 ATV OWNER'S MANUAL

0

Filed Under (Bajaj) by admin on 26-11-2010

download
FUEL AND OIL FUEL Proper fuel is very important for the engine. Ensure there is no dust, dirt, or water which has mixed in the fuel. Use regular unleaded gasoline with an octane number 90 or higher. ENGINE OIL Your 250cc ATV has a four-stroke engine. Please use oil as described in the chart below. By using prescribe oil, you will realize the best lubrication for engine. Use the chart to select a viscosity rating based on the temperature range in your area. NOTE: In very cold weather (below 5°F (-15°C), use SAE10W-30 for good starting and smooth operation. SAE 10W-30 SAE 20W-40 ENGINE TEMP. °C °F -30 -22 40 104 -10 14 0 32 10 50 20 68 30 86 -20 4 FUEL AND OIL 8 LOCATION OF LABELS Read and follow all of the warnings labels on your ATV. Make sure you understand all the labels. Keep the labels on the ATV. Do not remove them for any reason. If a label comes off or becomes difficult to read, you should get a replacement by contacting BAJA INC. 1 – Red Light – Reverse indicator Light illuminates when ATV is in Reverse. 2 – Green Light – Neutral indicator Light illuminates when ATV is in Neutral. 3 – Ignition key switch – Turn right (CW) “RUN”, Turn left (CCW) “OFF”. ATV will only start when ignition key is turned to the “RUN” position. Make sure ignition key switch is in the “OFF” position when not in use

Incoming search terms:

KYMCO MXU 375 ATV WINCH MOUNT KIT INSTALLATION INSTRUCTIONS

0

Filed Under (Kymco) by admin on 26-10-2010

download
WINCH MOUNT INSTALLATION INSTRUCTIONS 1. Remove molded plastic bumper guard from the ATV. 2. Mount the winch mount weldment (Item 1) to the ATV as shown below. 3. Mount the roller hawse to the winch mount weldment as shown above. 4
4. Mount the winch to the winch mount weldment and route the winch cable through the rollers. (Installer may need to remove rollers to allow cable end to pass through). 5. Wire the winch according to the manufacturer instructions. 6. Re-install the molded plastic bumper guard. 5 *CAUTION BE AWARE OF WHEN THE CABLE STOP CONTACTS THE ROLLER HAWSE AS CABLE IS WOUND IN. FAILURE TO RELEASE MAY CAUSE DAMAGE TO WINCH PARTS OR TO THE ATV. When using the winch to raise and lower a blade a cable stop must be installed. Carefully raise the blade until the top of the push tube’s are no closer than 1″ anywhere on the ATV. Place the Cable Stop onto the Winch Cable up against the Winch Hawse. Secure the Cable Stop to the Winch Cable using the Cable Clamp Assembly as shown in the pictures below.

Incoming search terms:

KTM ATV 525 XC specification

0

Filed Under (KTM) by admin on 12-11-2010

download
Engine ] Pure power for Enduro enthusiasts. The power of the 525 XC is the indisputable benchmark in the ATV Enduro sector. Its acceleration and top speed cast a shadow over all its predecessors. Variable ignition curves and perfect maintenance features like simple valve play adjustment and the removable clutch cover are even further highlights of the XC engine that make the KTM Enduro quads so superior. First Oil Filling for all KTM Engines. [ CarburEttor ] The Keihin carburettor, which has been proven multiple times in racing, with 39 mm and the Throttle Positioning System guarantees a uniform, forceful power delivery in all speed ranges. It ensures an unrivalled response behavior and perfect service-friendliness at all times. [ StartEr ] Packed in a space-saving manner into the free space behind the cylinder head, the small, light electric starter motor is ready for use. It brings every KTM ATV up to speed reliably and comfortably even when racing becomes hectic. [ rEar SuSPENSIoN ] Premium-quality ÖHLINS suspension components specially designed for tough Enduro use are provided as standard – both at the front and the rear. Easy to adjust, they guarantee optimal tuning for the most varied of terrains. Another highlight: the front and rear spring travel of 275 mm and 272 mm respectively is 100 % trend-setting for an Enduro ATV! [ alumINIum SubFramE ] The rear subframe is made of aluminium and is extremely light and easy to remove. [ FramE ] The lightweight, extremely durable frame sets the benchmark in the quad racing segment and is made of high-strength, powder-coated Chromoly steel. [ haNDlEbar ] An ultra-durable tapered aluminium Magura® handlebar comes standard that is four-position adjustable to suit your preferred ergonomics. Further highlights are the functional and individually adjustable operating levers for brake and hydraulic clutch. In addition, the chassis has an integrated mount for a steering damper – available as a PowerPart accessory. [ CurvED raDIator ] Best cooling by means of its curved shape and the resulting maximized surface area. [ rImS / tIrES ] MAXXIS Razr tyres on light, stable DWT aluminium rims. [ ExhauSt ] The powerful XC silencer is made of light-weight aluminium.

Incoming search terms:

HONDA ATV FOURTRAX 400EX REPAIR, INSTALLATION MANUAL

0

Filed Under (Honda) by admin on 10-12-2011

download
Never carry a passenger on an ATV. * Never operate an ATV on any paved surfaces, including sidewalks, driveways, parking lots and streets. * Never operate an ATV on

Incoming search terms:

Honda ATV 650 Lift Kit REMOVAL AND Installation

0

Filed Under (Honda) by admin on 14-01-2012

download
Place jack under center on the ATV front end and lift until front wheels clear the ground. Be careful to support ATV properly so that it is secure, but so that the A-arms and shocks can droop to full extension. 2. Remove front wheels and shocks. 3. Using a shock spring compressor, compress the spring on the shock and remove the spring retaining ring.
CAUTION: The spring is installed under tension. Failure to use a shock spring compressor could cause loss of control of the spring, which could unload rapidly causing bodily injury. If you do not have a shock spring compressor you should acquire one or take it to a dealer or professional mechanic for installation of the stiffeners. 4. Remove the spring. 5. Insert the smaller front spring stiffener onto the shock with the lip of the spring stop, on the shock, mating into the recessed portion of the spring stiffener. 6. Slide the spring back onto the shock and it should rest on the lip of the spring stiffener.
7. Reattach the spring retaining ring. 8. Repeat steps for the opposite side. Once springs are complete reattach the top of the shock to the top shock mount on the ATV and the spring stiffener will be closest to the A-arm. 9. Take two of the “L” brackets and connect them to the bottom of the shock, the part that connects to the A-arms. 10. There is a top and bottom to the “L” bracket. See the diagram

Incoming search terms:

2002 Kawasaki 360 ATV WINCH ACCESSORY INSTALLATION INSTRUCTIONS

0

Filed Under (Kawasaki) by admin on 08-05-2012

download
1. Remove the two 8mm bolts that attach the front bumper assembly to the ATV frame see figure 3. 2. Place Winch mounting plate (A1) into position and fasten the two bent down tabs to the ATV frame using the two 8mm bolts removed in step one, see figure 4, and figure 5. Do not tighten fully at this time. 3. Attach the front of the mounting plate using four 1/4-20 u- bolts (B1), eight lock washers (B2), and eight 1/4-20 hex nuts (B3), see figure 6. 4. Tighten all fastners for the mounting kit at this time. 5. Place winch into position behind the mounting plate. Attach the top two feet of the winch using two 5/16-18 hex cap screws and lock washer. These fasteners will be found in the hardware kit that came with the winch. Note: The winch has floating nuts in its feet. In some instances, a nut may be moved off to one side making it impossible to screw a bolt in. If this becomes the case, take a screwdriver and center the floating nut in the winch to the bolt hole opening. Now attach the bolt through the Winch Plate and into the winch. 6. If using a Cast Hawse Fairlead: It may be neccasary to remove the cast hawse fairlead from the fairlead mounting plate that came with the winch.

Honda, Polaris (2000 and older) ATV Thumb Warmer Installation Instructions

0

Filed Under (Honda) by admin on 15-12-2011

download
Hi/Low Switch Installation Choose a location for the switch, which is convenient and has sufficient rear clearance for the electrical connections and is within 18″ of a voltage-controlled wire (a wire in the lighting circuit). Drill a 1/2″ (13mm) hole and install the switch from the back. Leave the strain relief nut on the switch. On the front install the Hi/Low indicator tab and secure the switch and tab using the metal nut. The amount of switch barrel protruding can be adjusted by moving the strain relief nut. Wire Routing and Connections Route the electric cord along the handlebar to switchmarea and secure with supplied tie wraps, electrical tape, or both. Cut and strip to proper length. Attach a ground wire of sufficient length to go from the red wire to a good ground. WARNING: Lead wire slack in the area of the throttle must be neither excessive nor tight. Ensure no binding occurs when the throttle is open fully.,Soldering connections is the most durable method, but the following will provide years of service. Attach the 1/4″ female slip-on connectors to the white and blue wires and #10 ring terminal to warmer leads as shown in Figure 2. (A crimping tool works best, but a Vise Grips or pliers will work). Figure 2. Switch Connections (Option B) Connect the single yellow or red wire to a regulated (lighting) circuit using Option A (ATV has a switch in a lighting circuit with a 1/4″ tab) or Option B: Option B: Locate a power wire (usually yellow) leading to a headlight, taillight, or dash light (Figure 2). Using the red tap connector, place this power wire into the continuous channel and insert the red wire (do not strip insulation) completely to stop in the second channel. Make the connection by squeezing (w/pliers) the metal contact until flush with the top of the connector. Close the hinged cover until latched. Complete connections to switch and ground circuit.

Honda 300 2×4 Lift Kit Installation Instructions

0

Filed Under (Honda) by admin on 11-12-2011

download
This product is designed for us e on ATVs on which additional ground clearance and fender clearance is desired. It is designed for utility type, slower-speed use on relatively flat terrain in deep mud or snow. Although we have many thousands of satisfied lift kit customers and over 400 franchised dealers selling and installing lift kits, purchasers should be aware that use of this product may increase the frequency of required maintenance, part wear, and will raise the center of gravity on your ATV increasing risk of roll-over on side hills, ditches or other steep terrain. We recommend that wider tires and/or wheel spacers be used to achieve a wider stance and to improve stability of the ATV. Riders should be advised that the handling characteristics of a taller ATV are different and require extra care when riding on side hills or off-camber situations. If you further raise the center of gravity by adding heavy loads to racks or seats, the ATV must be operated with care, at slower speeds or on relatively flat ground. Operation of an ATV with or without a lift kit, while or shortly after consuming alcohol or drugs, subjects the rider to the risk of serious bodily harm or possible death. This is compounded if the rider does not wear an approved helmet and other safety gear. High Lifter urges that all approved safety gear be worn when riding an ATV. If this is not what you expected, or is not consistent with your intended use, you should return the product immediately to the seller, before installation, for a refund of the purchase price; less any fees. After installation, product is warranted for 90 days for defects in workmanship and materials. Warranty is limited to refund of the purchase price or replacement of the kit, at the seller’s option.

HONDA ATV Carburetor Repair Kits Installation

0

Filed Under (Honda) by admin on 21-12-2011

download
ATV Carburetor Repair Kits Complete kits to rebuild one OEM carburetor. Each kit contains necessary gaskets/o-rings, needle valve or needle valve set, and jets. Made in Japan. Note: Check all parts before installation. Honda Model Year Order No AT C70 78-85 025-001 AT C90 70-71 025-003 ATC90K1/K2/K3 72-75 025-003 AT C90 76-78 025-003 TRX90 Fourtrax 90 93-98 025-084 ATC110 79-83 025-005 ATC110 84-85 025-061 ATC125M 84-85 025-062 TRX125 Fourtrax 85-86 025-050 TRX125 Fourtrax 87-88 025-063 ATC185 1980 025-009 ATC185S 81-83 025-009 AT C200 81-82 025-008 AT C200 1983 025-009 ATC200E Big Red 82-83 025-064 ATC200ES Big Red 1984 025-064 AT C200M 84-85 025-064 AT C200S 84-86 025-065 AT C200X 83-85 025-012 AT C200X 86-87 025-014 TRX200 Fourtrax 200 90-91 025-066 TRX200D Fourtrax 200 Type II 1991 025-066 TRX200D Fourtrax 200 Type II 92-93 025-067 TRX200D Fourtrax 200 Type II 94-97 025-068 TRX200SX Fourtrax 87-88 025-069 ATC250R 81-82 025-017 ATC250R 83-84 025-018 AT C250R 1985 025-019 ATC250ES Big Red 85-87 025-029 AT C250SX 1985 025-070 TRX250 Fourtrax 250 1985 025-071 TRX250 Fourtrax 250 86-87 025-072 TRX250EX Sportrax 250EX 01-04 025-085 TRX250R Fourtrax 250R 86-87 025-060 TRX250R Fourtrax 250R 1988 025-073 TRX250X 91-92 025-074 TRX300 Fourtrax 300 1988 025-075 TRX300 Fourtrax 300 91-92 025-076 TRX300 Fourtrax 300 93-95 025-078 Honda Model Year Order No TRX300EX Fourtrax 300EX 93-98 025-081 TRX300FW Fourtrax 300 4×4 1988 025-075 TRX300FW Fourtrax 300 4×4 91-92 025-076 TRX300FW Fourtrax 300 4×4 93-95 025-078 AT C350X 1985 025-035 TRX350 Fourtrax 4×4 86-87 025-079 TRX350FE Fourtrax Rancher 4×4 ES 00-03 025-082 TRX350FM Fourtrax Rancher 4×4 00-03 025-082 TRX350TE Fourtrax Rancher ES 00-03 025-082 TRX350TM Fourtrax Rancher 00-03 025-082 TRX350D Fourtrax Foreman 4×4 87-89 025-079 TRX400FW Fourtrax Foreman 95-00 025-080 TRX450ES Fourtrax Foreman ES 98-01 025-083 TRX450FE Fourtrax Foreman ES 02-03 025-083 TRX450FM Fourtrax Foreman S 02-03 025-083 TRX450S Fourtrax Foreman S 98-01 025-083 TRX500FAFourtrax Rubicon 01-04 025-086

Incoming search terms:

1989-2000 Honda XR’S WHEEL REMOVAL AND SERVICE TOOLS

0

Filed Under (Honda) by admin on 15-12-2011

download
ATV BALL-JOINT SOCKET This tool is designed remove and install nut on Yamaha YFM350X Warrior. 35-8581 ATV Ball-Joint Wrench ATV BALL-JOINT SEPARATOR This tool is designed to separate the knuckle-ball joints on ATV’s without damage to the A-arm, ball joint stud or rubber boots. Sold as a kit with two separate press bolts to fit a variety of applications. Fits the following ATV applications: HONDA: TRX250R 86-89, TRX250X 87-88 & 90-91, TRX300EX 93-98 YAMAHA: YFZ350 Banshee 87-02, YFM350X Warrior 87-96 35-1975 ATV Ball-Joint Separator

Incoming search terms: