automotive spare part distributor company contact ar mail

You search Auto repair manual PDF automotive spare part distributor company contact ar mail, if there are search results will appear below. If search results do not exist, please search by others keyword.





BILLET ALUMINUM DISTRIBUTOR WITH ELECTRONIC ADVANCE AND ADJUSTABLE REV LIMITER FOR 1936-69 HARLEY BIG TWIN MOTORCYCLES INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 25-11-2010

download
ELECTRICAL SYSTEM A 12 volt electrical system is required. Check that the charging system is working properly and not producing over 16 volts. DISTRIBUTOR CLAMP A 1966-69 style distributor clamp (original or aftermarket) is required. MODULE This distributor uses an Accel Single/Dual Fire Ignition module part number 35496. See the enclosed form “Instruction Sheet Single/Dual Fire” for instructions on wiring, adjusting the rev limiter and selecting an advance curve. COIL(S) A coil(s) with a total primary resistance of 2 to 4 ohms is recommended. INSTALLATION Step 1 Turn the ignition switch to the off position. Rotate the engine until it is on the compression stroke for the front cylinder. Continue to rotate the engine until the TDC mark is visible through the timing hole. (see repair manual if necessary). Step 2 Remove the existing distributor if still in the engine. Step 3 Remove the two button head screws from the top of the Mallory distributor. Pull the top cover off the distributor. Remove the two hex standoffs and pull the module and upper housing off the distributor base assembly. Adjust the switches on the module for the desired advance curve and rev limit. FORM 1627 07/08 Step 4 Install the distributor base assembly in the engine with the screw holes and shutter wheel positioned as shown in Figures 1 and 2. It may be necessary to pull the distributor out, turn the shaft and reinstall to get the shutter wheel at the approximate angle shown. The slots should be at about the11 o’clock and 7 o’clock positions. The screw holes should be at the 9 o’clock and 3 o’clock positions. Step 5 Install the distributor clamp and tighten the clamp bolt lightly so the distributor can still be rotated. Step 6 Set the upper housing on the base assembly as shown in figure 3. (The upper housing will only install one way because of the locating screw) Rotate the base assembly slightly if necessary so that the slot in the shutter wheel lines up with the slot in the upper housing. Tighten the distributor clamp

Incoming search terms:

TOYOTA TACOMA 2005 SPARE TIRE LOCK Procedure

0

Filed Under (Toyota Manuals) by admin on 21-10-2011

download
1. Lower Spare Tire. (a) Lower spare tire using hooked jack handle supplied in the vehicle tool kit. 2. Install Spare Tire Lock. (a) Install the spare tire lock assembly on the lowering screw by lining up the cross pin in the lock with the slot in the lowering screw. (b) Tap lock in place with a rubber mallet until it is fully seated. (Pull on lock to ensure attachment.) (c) Install adapter shroud (protects cable and spring) using slotted washer. (See Fig. 2-1) 3. Install Key on Hooked Jack Handle. (a) Install key on hooked jack handle, pressing the jack handle into the slot in the key until the clip snaps in place

Incoming search terms:

TVS50 Voice Processing System Installation Manual

0

Filed Under (TVS) by admin on 27-10-2010

download
installation must be performed by a qualified professional installer. If required, provide the telephone company with the following technical information:  The telephone numbers to which the system will be connected Make: Panasonic Model: KX-TVS50 FCC Registration No.: found on the back of the unit Ringer Equivalence No.: 0.4B Facility Interface Code: 02LS2 Service Order Code: 9.0F Required Network Interface Jack: RJ11C Connection to the Telephone Line The VPS unit must not be connected to coin operated telephone lines. Contact the telephone company before connecting this unit to a party line. Telephone Service Problems The telephone company may temporarily discontinue service if the VPS causes problems with the telephone network. Discontinued service usually occurs after prior notification. When prior notification is not practical, the telephone company must:  Promptly notify the customer of the temporarily discontinued service.  Provide the customer with an opportunity to correct the situation or problem.  Inform the customer of the right to bring a complaint to the Federal Communication Commission pursuant to the procedures set forth in Subpart E of Part 68 of the FCC Telephone Equipment Rules. Telephone Network and Terminal Equipment compatibility Availability of Telephone Interface Information When requested by the customer, the telephone company must provide the following information:  technical information concerning interface parameters.  technical information not specified in FCC rules such as the number of ringers that can be connected to a particular telephone line. Changes in Telephone Company Communications Facilities, Equipment, Operations, and Procedures The telephone company may make changes to its communication facilities, equipment, operations, or procedures, when such action is reasonably required in the operation of its business, and is not inconsistent with FCC rules (FCC Telephone Equipment Rules, Part 68). The customer shall be given adequate notice in writing when changes will

Incoming search terms:

HARLEY DAVIDSON XL BRAIDED FRONT BRAKE LINE KITS INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 30-03-2011

download
REMOVAL Direct contact of D.O.T. 5 brake fluid with eyes can cause eye irritation, swelling, and redness. Avoid eye contact. In case of eye contact flush with large amounts of water and get medical attention. Swallowing large amounts of D.O.T. 5 brake fluid can cause digestive discomfort. If swallowed, obtain medical attention. Use in well ventilated area. KEEP OUT OF REACH OF CHILDREN. (00144a) Direct contact of D.O.T. 4 brake fluid with eyes can cause irritation. Avoid eye contact. In case of eye contact flush with large amounts of water and get medical attention. Swallowing large amounts of D.O.T. 4 brake fluid can cause digestive discomfort. If swallowed, obtain medical attention. Use in well ventilated area. KEEP OUT OF REACH OF CHILDREN. (00240a) D.O.T. 4 brake fluid will damage painted and body panel surfaces it comes in contact with. Always use caution and protect surfaces from spills whenever brake work is performed. Failure to comply can result in cosmetic damage. (00239b) 1. Drain the brake fluid following the instructions in the service manual. Dispose of waste properly. To prevent accidental vehicle start-up, which could cause death or serious injury, disconnect negative (-) battery cable before proceeding. (00048a) To prevent accidental vehicle start-up, which could cause death or serious injury, remove main fuse before proceeding. (00251b) 2. Disconnect the battery, negative (-) cable first or remove the main fuse. Follow the instructions in the service manual 3. Remove bolt and two sealing washers to disconnect brake line fitting from master cylinder. Discard sealing washers, but save bolt for installation. 4. Remove bolt and two sealing washers to disconnect brake line fitting from front brake caliper. Discard sealing washers, but save bolt for installation. 5. Carefully make note of brake line routing, then remove existing brake line. NOTE This kit contains clamps and cable straps to either replace the original equipment clamps and cable straps being removed or to add additional brake line support. INSTALLATION Install proper length brake lines. Incorrect brake line length can adversely affect motorcycle operation, which could cause loss of control resulting in death or serious injury. (00325a) Replace brake line gaskets. Re-using original gaskets can cause brake failure and loss of vehicle control, which could result in death or serious injury. (00318a) Avoid leakage. Be sure gaskets, banjo bolt(s) and brake line are clean and undamaged before assembly. (00323a) 1. Position new sealing washers from kit on each side of hydraulic brake fittings (banjo fittings). Small ID washers are for caliper end, large ID washers are for master cylinder end. 2. Insert bolts (removed earlier) through washers and fittings. 3. Hold new braided brake line in position and install bolts into master cylinder and caliper. Tighten only enough to keep banjo fitting in the same orientation as the stock banjo fitting. 4. Verify there is no twist in the brake line. Adjust brake line if necessary. 5. Install clamps from kit by wrapping clamp around braided brake line at each of the clamp mounting locations. Verify clamps are oriented the same as the stock clamps. Install clamp screws but do not tighten. 6. Check entire length of braided brake line: a. Be sure brake line is not twisted. b. Turn handlebars fully-left and right while checking to make sure brake line does not contact any vehicle components. c. Be sure brake line length between clamps is sufficient. 7. Adjust brake line if necessary. 8. Tighten caliper and master cylinder banjo bolts to 20-25 ft-lbs (27-34 Nm) .

Incoming search terms:

HARLEY DAVIDSON ROAD KING FAT HANDLEBAR KIT REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 11-03-2011

download
PREPARATION – ALL MODELS To prevent accidental vehicle start-up, which could cause death or serious injury, disconnect battery cables (negative (-) cable first) before proceeding. (00307a) Disconnect negative (-) battery cable first. If positive (+) cable should contact ground with negative (-) cable connected, the resulting sparks can cause a battery explosion, which could result in death or serious injury. (00049a) 1. See the service manual and remove the seat and disconnect battery cables or remove the main fuse. Direct contact of D.O.T. 5 brake fluid with eyes can cause eye irritation, swelling, and redness. Avoid eye contact. In case of eye contact flush with large amounts of water and get medical attention. Swallowing large amounts of D.O.T. 5 brake fluid can cause digestive discomfort. If swallowed, obtain medical attention. Use in well ventilated area. KEEP OUT OF REACH OF CHILDREN. (00144a) Direct contact of D.O.T. 4 brake fluid with eyes can cause irritation. Avoid eye contact. In case of eye contact flush with large amounts of water and get medical attention. Swallowing large amounts of D.O.T. 4 brake fluid can cause digestive discomfort. If swallowed, obtain medical attention. Use in well ventilated area. KEEP OUT OF REACH OF CHILDREN. (00240a) D.O.T. 4 brake fluid will dama ge painted and bod y panel surfaces it comes in contact with. Always use caution and protect surfaces from spills whenever brake work is performed. Failure to comply can result in cosmetic damage. (00239b) NOTES Immediately wipe up any brake fluid spills with a clean, dry, soft cloth. Follow up by thoroughly wiping affected area with a clean, damp, soft cloth (small spills) or washing with a large quantity of soapy water (large spills). Cover nearby motorcycle surfaces with a polyethylene protective sheet to help protect against damage to finish caused by spilled D.O.T. 4 brake fluid. 2. See the service manual and drain the brake fluid from the front brake reservoir. ORIGINAL HANDLEBAR REMOVAL NOTE Cover the front fender and the fuel tank with clean shop towels to prevent scratching. Damage to the finish could result. Remove brake line components carefully. Damage to seating surfaces can cause leakage. (00320a) 1. Using a T-40 TORX® drive head, remove and retain the button head screw on the underside of the fork stem and bracket assembly that holds the brake line manifold tee. 2. Carefully make note of the front brake line routing and the orientation of the banjo fittings. Disconnect the brake line from the front brake calipers and the front brake master cylinder assembly. Save the banjo bolts, but discard the two gaskets found at each banjo fitting. See FRONT BRAKE MASTER CYLINDER in the service manual. 3. Remove the old brake lines from the motorcycle. 4. Using a T27 TORX drive head, remove the front-brake master cylinder and clutch-lever assemblies (refer to CLUTCH CABLE in the service manual) from the stock handlebar.

Incoming search terms:

HARLEY DAVIDSON STREET SLAMMER HANDLEBAR KIT REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 15-02-2011

download
This kit does not fit models equipped with Hydraulic Clutch Kits, handlebar mounted gauges or the Road Tech® Radio or FLHRS models equipped with an accessory windshield. REMOVAL Preparation – All Models To prevent accidental vehicle start-up, which could cause death or serious injury, remove main fuse before proceeding. (00251b) To prevent accidental vehicle start-up, which could cause death or serious injury, disconnect battery cables (negative (-) cable first) before proceeding. (00307a) Disconnect negative (-) battery cable first. If positive (+) cable should contact ground with negative (-) cable connected, the resulting sparks can cause a battery explosion, which could result in death or serious injury. (00049a) 1. See the service manual and remove the seat and disconnect battery cables or remove the main fuse. Save the seat hardware for installation. -J04406 When servicing the fuel system, do not smoke or allo w open flame or sparks in the vicinity. Gasoline is extremely flammable and highly explosive, which could result in death or serious injury. (00330a) 2. Softail and Dyna models: See the service manual and loosen the fuel tank. Direct contact of D.O.T. 5 brake fluid with eyes can cause eye irritation, swelling, and redness. Avoid eye contact. In case of eye contact flush with large amounts of water and get medical attention. Swallowing large amounts of D.O.T. 5 brake fluid can cause digestive discomfort. If swallowed, obtain medical attention. Use in well ventilated area. KEEP OUT OF REACH OF CHILDREN. (00144a) Direct contact of D.O.T. 4 brake fluid with eyes can cause irritation. Avoid eye contact. In case of eye contact flush with large amounts of water and get medical attention. Swallowing large amounts of D.O.T. 4 brake fluid can cause digestive discomfort. If swallowed, obtain medical attention. Use in well ventilated area. KEEP OUT OF REACH OF CHILDREN. (00240a) D.O.T. 4 brake fluid will damage painted and body panel surfaces it comes in contact with. Always use caution and protect surfaces from spills whenever brake work is performed. Failure to comply can result in cosmetic damage. (00239b) NOTES Immediately wipe up any brake fluid spills with a clean, dry, soft cloth. Follow up by thoroughly wiping affected area with a clean, damp, soft cloth (small spills) or washing with a large quantity of soapy water (large spills). Cover nearby motorcycle surfaces with a polyethylene protective sheet to help protect against damage to finish caused by spilled DOT 4 brake fluid. 3. See the service manual and drain the brake fluid from the front brake reservoir and brake lines. Handlebar Removal – Dyna and Softail NOTE Cover the front fender and the fuel tank with clean shop towels to prevent scratching. Damage to the finish could result. 1. Note the front brake line routing and the orientation of the banjo fittings. See the service manual and disconnect and remove the brake line. Save the banjo bolts, but discard the brake line gaskets. 2. Remove the plastic wiring retainer clips that secure the turn signal harnesses to the handlebar, if equipped. 3. Remove the front brake master cylinder and clutch lever assemblies from the handlebar.

Incoming search terms:

Automotive Service, Diagnosis & Repair – Toyota/ Lexus/ Scion Technician

0

Filed Under (Toyota Manuals) by admin on 12-06-2011

Download
The courses listed in the Automotive Service, Diagnosis and Repair – Toyota/Lexus/Scion Technician certificate are selected to provide a comprehensive set of job skills needed by Toyota, Lexus and Scion
technicians. In addition to improving the student’s employability, the skills developed in each course will enhance their ability to become Automotive Service Excellence (ASE) certified in all eight ASE areas. The certificate is designed to prepare an individual for employment or provide the skills needed for careeradvancement.

Incoming search terms:

HARLEY DAVIDSON NARROW BEACH HANDLEBAR KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 14-04-2011

download
INSTALLATION Preparation To prevent accidental vehicle start-up, which could cause death or serious injury, disconnect battery cables (negative (-) cable first) before proceeding. (00307a) Disconnect negative (-) battery cable first. If positive (+) cable should contact ground with negative (-) cable connected, the resulting sparks can cause a battery explosion, which could result in death or serious injury. (00049a) 1. Refer to the Service Manual and follow the instructions given to remove the seat and disconnect the battery cables, negative cable first. Retain all seat mounting hardware. When servicing the fuel system, do not smoke or allow open flame or sparks in the vicinity. Gasoline is extremely flammable and highly explosive, which could result in death or serious injury. (00330a) 2. Loosen the fuel tank. Refer to FUEL TANK REMOVAL in the appropriate section (Carbureted or EFI Engine) of the Service Manual. Direct contact of D.O.T. 5 brake fluid with eyes can cause eye irritation, swelling, and redness. Avoid eye contact. In case of eye contact flush with large amounts of water and get medical attention. Swallowing large amounts of D.O.T. 5 brake fluid can cause digestive discomfort. If swallowed, obtain medical attention. Use in well ventilated area. KEEP OUT OF REACH OF CHILDREN. (00144a) Direct contact of D.O.T. 4 brake fluid with eyes can cause irritation. Avoid eye contact. In case of eye contact flush with large amounts of water and get medical attention. Swallowing large amounts of D.O.T. 4 brake fluid can cause digestive discomfort. If swallowed, obtain medical attention. Use in well ventilated area. KEEP OUT OF REACH OF CHILDREN. (00240a

Incoming search terms:

Contact Us

0

Filed Under () by admin on 23-05-2017

If you have any question or suggestions about this website, or want to advertise on this website, or found any copyrighted document, please contact us at this email: septryadi @ yahoo.com. If you want to send DMCA request, please follow DMCA page to send copyright issues.

We are a free pdf share document that provides an option to search for and download various PDF documents, data sheets etc. We don’t host any files. Our crawlers harvested a huge database PDF files through different open Internet resources such as blogs, forums, BBS and others. This database is regularly checked for file validity so now you can search within more than three million of live PDF files.

We are glad to see You at Our Service. We hope it will be useful to you and your friends, You’ll enjoy our service and share Your experience with your friends! Check back in from time to time to see what we’ve done new. If You have any questions or have something interesting to offer please feel free to contact us.

Incoming search terms:

HARLEY DAVIDSON BRAIDED, DUAL DISC, FRONT BRAKE LINE KITS INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 20-04-2011

download
INSTALLATION 1 is03017 1. Bleed valve cover Figure 1. Brake Caliper Bleed Valve Rubber Cover 2 1 3 is03018 1. Plastic tube 2. Caliper bleeder valve 3. Container Figure 2. Draining Brake Fluid NOTE This instruction sheet covers motorcycle models that use either DOT 4 or DOT 5 Hydraulic Brake Fluid. The owner’s manual -J03109 1 of 2 will indicate which type of br ake fluid should be used on the motorcycle. Read and follow the owner’s manual carefully. Direct contact of D.O.T. 5 brake fluid with eyes can cause eye irritation, swelling, and redness. Avoid eye contact. In case of eye contact flush with large amounts of water and get medical attention. Swallowing large amounts of D.O.T. 5 brake fluid can cause digestive discomfort. If swallowed, obtain medical attention. Use in well ventilated area. KEEP OUT OF REACH OF CHILDREN. (00144a) Direct contact of D.O.T. 4 brake fluid with eyes can cause irritation. Avoid eye contact. In case of eye contact flush with large amounts of water and get medical attention. Swallowing large amounts of D.O.T. 4 brake fluid can cause digestive discomfort. If swallowed, obtain medical attention. Use in well ventilated area. KEEP OUT OF REACH OF CHILDREN. (00240a) D.O.T. 4 brake fluid will damage painted and body panel surfaces it comes in contact with. Always use caution and protect surfaces from spills whenever brake work is performed. Failure to comply can result in cosmetic damage. (00239b) To prevent accidental vehicle start-up, which could cause death or serious injury, remove main fuse before proceeding. (00251b) To prevent accidental vehicle start-up, which could cause death or serious injury, disconnect battery cables (negative (-) cable first) before proceeding. (00307a) 1. See the service manual and disconnect negative (-) battery cable or remove the main fuse. Save the seat hardware for installation. 2. See Figure 2. Open bleeder nipple cap on front brake caliper. Install end of a length of plastic tubing over caliper bleeder valve (1), while placing free end in a suitable container. Open bleeder valve approximately 1/2 turn. Pump brake lever to drain brake fluid. Repeat step for the other caliper. 3. Remove bolt and two sealing washers to disconnect brake line fitting from master cylinder. Save bolt and discard washers.

Incoming search terms: