bad ecm in heritage classic

You search Auto repair manual PDF bad ecm in heritage classic, if there are search results will appear below. If search results do not exist, please search by others keyword.



  bad ecm in heritage classic Direct Download speed 5282 Kb/s

  bad ecm in heritage classic Full Version speed 6162 Kb/s



2002 URAL Classic Motorcycles BC-75 (Bavarian Classic) LC-75 (Luxury Cruiser) Tourist, Adirondac & Patro Owner's Manual

0

Filed Under (Ural) by admin on 02-11-2010

download
Front brake control lever (Fig.1, #5). When the lever is squeezed, the front wheel brake is actuated. The front brake should be used together with rear brake. When the brake lever is squeezed, the stop signal lamps are switched on. Kick lever (Fig.1, #11) is designed to start the engine. On pressing the lever the crankshaft of the engine is actuated through the gearbox. The lever is returned to its initial position by the spring inside the gearbox. Note: this is a backup to the electric starter. Gear shift foot pedal (Fig.1, #12) is a two-arm type. When the front arm is pressed, shifting from high to lower gears takes place. When the rear arm is pressed, shifting from low to higher gears takes place. Since the heel-toe shift lever is short-coupled, you will find it easier to shift up if you rotate the heel of your left foot in towards the rear arm before stepping on it with your heel. The neutral position is fixed between the I and II gears. Speedometer is on the dash board, with trip (Note..BC-75 has no trip odometer) and total odometer. The trip odometer is reset to zero by rotating push-button (Fig.1, # 3) counterclockwise. Note that the odometer reads in kilometers not miles. Ignition Switch (Fig.1, # 19) has three fixed positions of the key. The position and switching diagram of the ignition locks are shown above.
18 The indicator lamps are mounted on the instrument board: (Fig. 1, # 2) — turn indicator pilot lamp, (orange) (Fig. 1, # 4) — gearbox neutral and reverse gear engagement, (green) (Fig. 1, # 18) — head lamp high beam indicator, (dark blue) (Fig. 1, # 20) — alternator fault indicator lamp, (red) Note: If the red alternator fault light stays on continuously during normal operation above approximately 1500 RPM, there is a problem with the charging system or battery. Throttle Control (Fig.1, # 6) is on the right handlebar. Turning the twist grip counterclockwise increases engine speed. Ignition Cutoff Switch (Fig.1, # 7) has two positions, ignition off (up), and ignition on (down). Low and High Beam Light Switch (Fig.1, # 15), turn indicator switch (Fig.1, #13) and horn push-button (Fig.1, # 14) are combined in one unit on the left-hand handle bar control housing. Master Battery Switch (Fig.1, # 21) is under the seat. Electric Start Button (Fig. 1, # 8) is located on the right-hand twist grip, below the kill switch. The Steering Damper absorbs lateral kicks on the front wheel. Turning tightening bolt (Fig.1, # 17) clockwise increases friction. This can be used while riding over bad roads

INSTRUCTIONS FOR PROGRAMMING KEYS INTO RE-FLASHED TOYOTA / LEXUS ECM

0

Filed Under (Toyota Manuals) by admin on 23-06-2011

Download
After we re-flash the ECM it will be in “Automatic Registration Mode” when you install it. The ECM is
expecting that when first powered up (by turning on a key) that it will encounter 3 new keys. The first two keys
are internally (inside the ECM) designated as MASTER keys and the 3rd key inserted will be internally
designated as the VALET key. The ECM can be programmed with as few as 1 key. If less than 3 keys are
programmed into the ECM the security light may flash for some time (hours to weeks) until the ECM “learns”
that it is apparently not going to get any more keys.

Incoming search terms:

2009 Harley Davidson Softail POWER COMMANDER V INPUT ACCESSORY INSTALLATION

0

Filed Under (Harley Davidson) by admin on 26-02-2012

download
1 Remove the seat 2 Uplug the stock wiring harness from the ECM (Fig. A) 3 Remove the 4 nuts that hold the ECM to the bracket and remove the ECM. 4 Remove the bolt that holds the seat strap to the rear fender. 5 Remove the ECM bracket from the fender. Remove one nut at a time or the bracket will fall into the tire. Reinstall the nuts to support the inner fender bracket. Due to the limited amount of room on this bike the seat strap and ECM bracket can NOTbe re-used. 6 Connect the PCVharness in-line of the stock wiring harness and ECM (Fig. B). 7 Place the BLACK PCVto GREYstock connector as close to the fuse box as possible. This connection will NOT lay flat against the frame. 8 Using the supplied velcro secure the ECM to the rear fender. Place the ECM as far down as possible. The upper part of the ECM will just overlap the bolt hole for the seat strap. Make sure to clean both surfaces with the alcohol swab before attaching. If using the Autotune kit offset the ECM about 1″ from center to the right side of the bike. 9 Remove the security module from the top of the battery (Fig. C). This unit slides to the right of the bike.

Incoming search terms:

HARLEY DAVIDSON ULTRA CLASSIC AND ELECTRA GLIDE CLASSIC TOUR PACK ADJUSTMENT KIT INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 23-04-2012

download
1. Open the Tour Pack and remove all of the contents. 2. Remove map bag and inner pack liner. Pack liner comes out quite easily once map bag is removed. 3. Remove the 4 bolts inside the tour pack that are located on top of the metal support plate that hold the tour pack to the luggage rack. Have your assistant hold the pack in place before removing the last bolt. 4. Gently tip the tour pack forward to expose the supporting luggage rack under the pack. 5. While your assistant holds the pack up, place the two adjusting bars on top of the supporting luggage rack. Use the 4 flat head screws supplied with the kit to mount the bars snugly to the support rack (see fig. 1). 6. Reposition the tour pack over the threaded holes in the adjusting bars at the 2″ or 3″ position and bolt it in place snugly (see fig. 2). 7. Replace the trunk liner and map case and the installation is complete

Incoming search terms:

2001-2003 GL1800/ A ECM Replacement/ Cooling System REPAIR PROCEDURES

0

Filed Under (Honda) by admin on 29-01-2011

download
Install the new ECM, then reinstall the cruise/ reverse control module in the reverse order of removal. NOTE: When you start the vehicle – after completing ALL procedures – the new ECM will require initialization . To initialize the new ECM, perform the following procedure: • Start the bike and allow it to warm up to normal operating temperature and remain at idle for at least 90 seconds . Do not operate the throttle during this time; if you do, the ECU will not initialize properly and the process will need to be repeated. 5. Proceed to the Cylinder Head Inspection section below. Use the Cylinder Head Inspection Kit for the Cylinder Head Inspection procedure. Use the kit for each GL1800/A you inspect. Do NOT dispose of kit items. 1) 19X20 mm cap (2) (cap B) 2) 8X15 mm cap (cap A) 3) Hose plug 4) Bottle/cap w/feed hose 5) Harness clips (10) 6) Harness tape 7) Inspection mirror A limited number of additional Cylinder Head Inspection Kits are available: call TechLine at 800-421-1900, ext. 1 if you need one. Kit contents are NOT available separately as parts. NOTE: • The following late ’03 models do not have to have their cylinder heads inspected: • Perform the following procedure with the engine at room temperature. • Both Left and Right cylinder heads must be inspected. • Use the Cylinder Head Inspection Kit for the following procedure. 1. Remove the front lower fairing. (See S/M, 2-6) 2. Remove and suspend the rear brake reservoir, being careful not to stress the brake hose. (See S/M, 15-A-8) CONNECTOR B (22-GRY) CONNECTOR C (6-BLK) CONNECTOR A (22-BLK) ECM (ENGINE CONTROL MODULE) 1 2 3 4 5 6 7 Late ’03 (Non-ABS): after VIN 1HFSC470*3A204632 Late ’03 (ABS): after VIN 1HFSC474*3A201020 Cylinder Head Inspection Kit Cylinder Head Inspection

Incoming search terms:

Toyota Engine Control Module (ECM) Parts Information

0

Filed Under (Toyota Manuals) by admin on 20-10-2011

download
2005-2008 Corolla Engine(s): 1ZZ Transmission(s): 5MT, 4AT VDS(s): BR30E, BR32E 2005-2008 Matrix Drive Type(s): 2WD Engine(s): 1ZZ Transmission(s): 4AT, 5MT VDS(s): KR30E, KR32E Introduction The purpose of this TSB is to provide the Engine Control Module/ECM (SAE term: Power train Control Module/PCM) parts information necessary for proper identification and vehicle application. A vehicle with an incorrect ECM (PCM) installed may cause one or both of the following conditions: •M.I.L. “ON”DTCP0741-Torque Converter Clutch Solenoid Performance (Shift Solenoid Valve SL). •Failureto complete On-Board Diagnostic (OBDII) Readiness Monitors. NOTE If the part number is correct, the ECM (PCM) is NOT the cause of the DTC or OBDII Readiness Monitor concern.

SUZUKI SV 1000 RADIATOR (COOLING SYSTEM) SERVICE MANUAL

0

Filed Under (Suzuki) by admin on 26-02-2011

download
FI SYSTEM MALFUNCTION CODE AND DEFECTIVE CONDITION MALFUNCTION CODE DETECTED ITEM DETECTED FAILURE CONDITION CHECK FOR COO NO FAULT C11 Camshaft position sen- sor The signal does not reach ECM for more than 3 sec . after receiving the starter signal . The camshaft position sensor wiring and mechanical parts (Camshaft position sensor, intake cam pin, wiring/coupler con- nection) C12 Crankshaft position sensor The signal does not reach ECM for more than 2 sec . after receiving the starter signal . The crankshaft position sensor wiring and mechanical parts (Crankshaft position sensor, wiring/coupler connection) C13 Intake air pressure sensor The sensor should produce following voltage . (0.50 V < sensor voltage < 4 .85 V) Without the above range, C13 is indicated. Intake air pressure sensor, wiring/coupler connection C14 Throttle position sen- sor The sensor should produce following voltage . (0.20 V < sensor voltage < 4 .80 V) Without the above range, C14 is indicated. Throttle position sensor, wiring/coupler connection C15 Engine coolant temperature sensor The sensor voltage should be the following. (0.15 V <_ sensor voltage < 4 .5 V) Without the above range, C15 is indicated. Engine coolant temperature sensor, wiring/coupler connection C21 Intake air temperature sensor The sensor voltage should be the following. (0.15 V < sensor voltage < 4 .5 V) Without the above range, C21 is indicated. Intake air temperature sensor, wiring/coupler connection C22 Atmospheric pressure sensor The sensor voltage should be the following. (0.50 V < sensor voltage < 4 .5 V) Without the above range, C22 is indicated. Atm. pressure sensor, wiring/coupler connection C23 Tip over sensor The sensor voltage should be the following for more than 2 sec . after ignition switch turns ON . (0 .20 V < sensor voltage < 4 .80 V) Without the above value, C23 is indicated. Tip over sensor, wiring/coupler connection C24 or C25 Ignition signalCrankshaft position sensor signal is produced and ECM determines the ignition signal but signal from ignition coil is interrupted continuous by 4 times or more. In this case, the code C24 or C25 is indicated. Ignition coil, wiring/coupler connection, power supply from the battery SERVICING INFORMATION 8 .3 C28 Secondary throttle valve actuator No operating voltage is supplied from the ECM, C28 is indicated. STVA can not operate. STVA lead wire/coupler, STVA C29 Secondary throttle valve position sensor The sensor should produce following voltage . (0.10 V < sensor voltage < 4 .90 V) Without the above range, C29 is indicated . Secondary throttle position sensor, wiring/coupler connection C31 Gear position signalGear position signal voltage should be higher than the following for more than 2 seconds. (Gear position switch voltage >_ 0 .6 V) Without the above value, C31 is indicated. Gear position sensor, wiring/coupler connection, gearshift cam, etc. C32 or C33 Fuel injector Crankshaft position sensor signal is produced and ECM determines the injection signal but fuel injection signal is interrupted continuous by 4 times or more. In this case, the code C32 or C33 is indicated. Injector, wiring/coupler connection, power supply to the injector C41 Fuel pump relay No voltage is applied to fuel pump although fuel pump relay is turned ON, or voltage is applied to fuel pump although fuel pump relay is turned OFF . Fuel pump relay, connecting lead, power source to fuel pump relay C42 Ignition switchIgnition switch signal is not input in the ECM . Ignition switch, lead wire/coupler C44 Heated oxygen sensor (HO2S) [For E-02, 19] During 02 feedback control, 02 sensor voltage is higher or lower than the specification . No signal is detected during engine operation or no electrical power is supplied from the battery . HO2S lead wire/coupler connection Battery voltage supply to the HO2S C49 PAIR control solenoid valve (PAIR valve) When no operating voltage is supplied from the ECM, C49 is indicated. PAIR valve can not operate. PAIR valve lead wire/coupler

Incoming search terms:

Suzuki GSX-R 1000 AFR Tuner INSTALLATION MANUAL

0

Filed Under (Suzuki) by admin on 20-02-2012

download
The installation of the AFR Tuner should be done by experienced technicians only. Always disconnect the battery from the motorcycle before making any modification to the wiring harness. Remove the negative terminal from the battery before starting the installation work. The quality of the installation work greatly affects the reliability of the AFR Tuner and the motorcycle. Work precisely and very carefully when modifying the wiring harness of the vehicle. Always double check that the wire you are about to cut or tap into is the correct one. The ECM or the AFR Tuner can be destroyed by a faulty installation. 3.2. Installing the AFR Tuner to the wiring harness 3.2.1. Main cable The AFR Tuner connects to the motorcycle through its Main connector . Figure 2 shows the wiring diagram and the necessary modifications, which needs to be made when installing the unit into the fuel injection system of the motorcycle. Information about the ECM terminal numbers and wire colors for some popular motorcycles can be found in Chapter 6 . The best location for installing the AFR Tuner main unit is at the passenger seat area of the motorcycle mounted in the trunk space or on the subframe under the fairing, as this place provides protection from engine heat and the weather. Electrical contact between the metal casing of the AFR Tuner and the rear subframe must be prevented by using insulating material, such as the included self adhesive velcro strips. If necessary use some cable ties to secure the unit in place. The installation of the AFR Tuner into the wiring harness involves tapping into some wires and cutting others while connecting the two ends to the AFR Tuner. The harness modifications are best done near the ECM, since most of the wires can be found there. Part of the wiring modifications are related to connecting the AFR Tuner in-line between the ECM and the fuel injectors. In such cases when the motorcycle is equipped with primary and secondary injectors the AFR Tuner has to be installed on the primary injectors, which operate under all engine conditions. Correct grounding of the AFR Tuner is very important for electrical noise reduction. The above mentioned insulation of the metal case from the motorcycle frame is necessary for the same reason, which is to avoid the forming of a ground loop. An even more important requirement is the correct connection of the three ground wires of the AFR Tuner. As shown on Figure 2 , these three wires must be led out separately to the ECM and connected together at same point where the ECM ground wire is tapped into. This point should be as close to the ECM terminal as possible. For best quality of the electrical contacts all connections should be done by soldering and covering the exposed part of the wire with heat shrink tubing. For reliability reasons do not use clip on type wire taps

2000 Harley-Davidson FLHRCI Road King Classic

0

Filed Under (Harley Davidson) by admin on 03-11-2010

download
the Road King® Classic is a motorcycle with enough traditional styling to drop jaws throughout the continent. The Road King® Classic boasts laced wheels, fat white-walls and gorgeous leather saddlebags with hard inserts so they keep their shape across the long miles. Slightly narrower new handlebars provide improved ergonomics. Fender tips, tank and seat valance all boast a metal emblem. The model is available with a fuel-injected, chrome-and-black Harley- Davidson® Twin Cam 88 engine. Specifications: Engine Type: 1449 cc, 4-Stroke, Air Cooled, V-Twin Engine Bore and Stroke: 95.3 mm x 101.6 mm Valves 2 valves/cylinder Claimed Horsepower: 67 hp (50 kW) @ 5200 rpm Maximum Torque: 110 Nm (81.1 ft. lbs) @ 3100 rpm Transmission type: 5 speed Final Drive: Belt Tire – Front: 130/90-16 Tire – Rear: 130/90-16 Brakes – Front: dual 292 mm discs with 4-piston calipers Brakes – Rear: single 292 mm disc with 4-piston calipers

2001 URAL Classic Motorcycles Owner's Manual

0

Filed Under (Ural) by admin on 02-11-2010

download
Front brake control lever (Fig.1, #5). When the lever is squeezed, the front wheel brake is actuated. The front brake should be used together with rear brake. When the brake lever is squeezed, the stop signal lamps are switched on. Kick lever (Fig.1, #11) is designed to start the engine. On pressing the lever the crankshaft of the engine is actuated through the gearbox. The lever is returned to its initial position by the spring inside the gearbox. Note: this is a backup to the electric starter. Gear shift foot pedal (Fig.1, #12) is a two-arm type. When the front arm is pressed, shifting from high to lower gears takes place. When the rear arm is pressed, shifting from low to higher gears takes place. Since the heel-toe shift lever is short-coupled, you will find it easier to shift up if you rotate the heel of your left foot in towards the rear arm before stepping on it with your heel. The neutral position is fixed between the I and II gears. Throttle Control (Fig.1, # 6) is on the right handlebar. Turning the twist grip counterclockwise increases engine speed. Engine cutoff switch (Fig.1, # 7) has two positions, ignition off (up), and ignition on (down). Low and high beam light switch (Fig.1, # 15), turn indicator switch (Fig.1, #13) and horn push-button (Fig.1, # 14) are combined in one unit on the left-hand handle bar control housing. Master battery switch (Fig.1, # 21) is under the seat. Electric Start Button (Fig. 1, # 8) is located on the right-hand twist grip, below the kill switch. The steering damper absorbs lateral kicks on the front wheel. Turning tightening bolt (Fig.1, # 17) clockwise increases friction. This can be used while riding over bad roads. WARNING: DO NOT TIGHTEN THE DAMPER TO THE POINT WHERE THE STEERING BECOMES STIFF . DOING SO WILL ADVERSELY AFFECT HANDLING QUALITIES . Parking brake (Fig. 1, # 22) is located on the right side of the motorcycle next to the foot peg. It is engaged by applying the foot brake pedal fully and turning the handle and pushing it down to hold the foot brake lever in the applied position. Always disengage the parking brake before moving the motorcycle