bearing size for wheel hub motorcycle xrm

You search Auto repair manual PDF bearing size for wheel hub motorcycle xrm, if there are search results will appear below. If search results do not exist, please search by others keyword.



  bearing size for wheel hub motorcycle xrm Direct Download speed 5282 Kb/s

  bearing size for wheel hub motorcycle xrm Full Version speed 6162 Kb/s



HARLEY DAVIDSON FRONT THUNDERSTAR WHEELS INSTALLATION

0

Filed Under (Harley Davidson) by admin on 08-11-2010

download
Remove existing front wheel assembly. Save axle, axle nut, brake disc, and wheel spacers for kit installation. Refer to FRONT WHEEL in service manual. For FLSTC and FLSTN Models: Discard moon-style hub cap. -J04065 1 of 8 For FXSTD Models: Discard the tapered r ight side wheel spacer. Do not re-use brake disc/rotor screws. Re-using these screws can result in torque loss and damage to brake components. (00319c) NOTE • For Kits 43573-08, 43575-08, 43703-08, 43978-07, 43771- 07, 43609-07, 44323-07, 44282-07, 44322-07, 43975-07, 43602-07 and 43773-07 install short valve stem (43157- 83A) included in the installation kit. • For Kits 40943-09, 40966-09 and 40996-09 install long valve stem (43206-01) included in the installation kit. 2. See Figure 2. Install valve stem assembly (L, M or N) on wheel. Refer to TIRES in service manual. 3. Assemble wheel installation kit components and brake disc(s) to wheel, using the appropriate service parts table. Refer to FRONT WHEEL in Service Manual. NOTES Install the primary bearing first using appropriate service manual and WHEEL BEARING REMOVER/INSTALLER. For Kits 43573-08, 43575-08, 43703-08, 43978-07, 43771-07, 43609-07, 40943-09, 40966-09 and 40996-09: • The left side of the wheel has a machined groove (item 5, Figure 2) in the hub face and/or DOT markings to identify it as the brake disc and primary bearing side. • Install the wheel so that the valve stem is on the right side of the motorcycle. For Kits 44323-07, 44322-07 and 44282-07: • Install the wheel so that the hub markings are on the left side of the motorcycle. The left side of the wheel has a machined groove (item 5, Figure 2) in the hub face and hub markings to identify it as the primary bearing side. • These kits include one or two hub plates (43985-00) to install between the brake disc and the wheel and a chrome hub cap (43986-00) to install on the wheel opposite the brake disc side. Hub covers must be installed to prevent water intrusion, which could cause an imbalance condition. Dual brake disc models: Install one stainless steel hub plate (3) between each brake disc and wheel hub. Discard chrome hub cap (2). Install brake discs according to service manual procedures. Single brake disc models: Install one stainless steel hub plate (3) between the brake disc and wheel hub. Install the brake disc according to service manual procedures. Install the chrome hub cap (2) on the side opposite the brake disc. Discard extra stainless steel hub plate (3). • The gross axle weight ratings is unaffected by the installation of this wheel on a vehicle equipped with a 21-inch wheel. For Kits 43975-07, 43773-07, and 43602-07: • The wheel has a machined groove (item 5, Figure 2) in the hub face to identify the right side. • For 2007 and later FX Softail Models and 2008 and later FXDWG: The left side of the wheel is the primary bearing side. For all other models the right side of the wheel is the primary bearing side. • For Kit 43602-07: An arrow is engraved into the right side hub to indicate the direction of rotation. • For Kits 43975-07 and 43773-07: An arrow is cast between the spokes on the right side to indicate the direction of rotation. • These kits include one or two hub plates (43985-00) to install between the brake disc and the wheel and a chrome hub cap (43986-00) to install on the wheel opposite the brake-disc side. Hub covers must be installed to prevent water intrusion, which could cause an imbalance condition. Dual brake disc models: Install one stainless steel hub plate (3) between each brake disc and wheel hub. Discard chrome hub cap (2). Install brake discs according to service manual procedures. Single brake disc models: Install one stainless steel hub plate (3) between the brake disc and wheel hub. Install the brake disc according to service manual procedures. Install the chrome hub cap (2) on the side opposite the brake disc. Discard extra stainless steel hub plate (3). 4. Install wheel assembly parts from the appropriate Service Parts table for this fitment and stock brake disc. Discard parts from the installation kit that are not required. Refer to FRONT WHEEL in Service Manual. 5. For FLSTC and FLSTN Models: Install wheel kit and right side wheel spacer provided in installation kit. For FXSTD Models: Install wheel kit, stock left wheel spacer and right side wheel spacer from installation kit in place of the tapered right side wheel spacer discarded in Step 1. Refer to FRONT WHEEL in service manual. For FXSTS Models: Install the left side wheel spacer provided in the kit between the stock left wheel spacer and the left fork. All other models: Install wheel spacers previously removed. 6. Install front wheel (1), stock axle and stock axle nut. Refer to FRONT WHEEL in service manual

Incoming search terms:

HARLEY DAVIDSON WHEEL BEARING REMOVAL AND INSTALLATION TOOL

0

Filed Under (Harley Davidson) by admin on 19-02-2011

download
BEARING REMOVAL 1. Place the wheel vertically in a vise and protect the rim from being marred. NOTE See Figure 1 for the tool lubrication locations before using. 2. Assemble the remover tool. a. Install wheel bearing puller (1), (2) or (16) depending on the bearing I.D. See the service parts table for the size reference. Install the wheel bearing puller into the bearing by hand or use a rubber mallet ( not a hard-faced hammer) to push through the bearing I.D. Stop pushing on the bearing puller as soon as it has cleared the inside of the bearing race. There will be a slight click. b. Place main body puller (3) over bearing puller with the fingers of main body puller facing the wheel. Lightly oil all threads. c. Place the large brass washer (10) and nut (13) onto the puller and hand-tighten the nut until it stops at the top face of the bridge. 3. Remove the front wheel bearings. a. Apply a small amount of oil to the taper at the hex end of the expander dowel. Insert the expander dowel (7) through the other side of wheel bearings, and through the bearing puller. b. Install the washer (15 and nut (14) to the expander dowel and torque to 100 in-lbs (11.3 Nm) with a 11/16 inch wrench or socket while holding the other side of the expander dowel by reaching the opposite side of the wheel with a 3/8 inch hex key. c. Align the main body puller support fingers centered over the bearing to be removed. If main body puller will be directly on a finished chrome surface, protect the surface area. d. If resistance is felt with a torque wrench set at 40 ft- lbs (54.2 Nm) of torque, you will need to apply heat to the hub area surrounding the bearing. Prior to applying heat, place 2 to 3 temperature stickers (P/N 94146-10) around the circumference of the hub. Apply indirect heat using a heat gun. Do not exceed 210°F. With a 1-1/8 inch socket and torque wrench, turn the nut (13) until the bearing is pulled free from the wheel hub. e. Using a 3/8 in. hex key on an extension and torque wrench set on the expander dowel (7) and a 1-1/8 inch wrench. Turn the nut (13) until the bearing is free of the wheel hub. 4. Remove the wheel bearing spacer from the I.D. of the wheel hub. 5. Repeat steps 1 through 4 for the opposite bearing. NOTE Remove rear wheel belt sprocket before removing the bearings. 6. Rear wheel bearing removal is the same as steps 1 through 4 by using the correct size wheel bearing puller

Incoming search terms:

HARLEY DAVIDSON BLADE FRONT WHEEL KITS INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 20-03-2011

download
INSTALLATION 1. Remove existing front wheel assembly. Save axle, axle nut, brake disc, and wheel spacers for kit installation. Refer to FRONT WHEEL in service manual. For FLSTC and FLSTN Models: Discard moon-style hub cap. or FXSTD: Discard tapered spacer. NOTE Install short valve stem (43157-83A) included in the installation kit. Discard all other valve stems. 2. See Figure 2. Install valve stem assembly (L) on wheel. Refer to TIRES in service manual. Do not re-use brake disc/rotor screws. Re-using these screws can result in torque loss and damage to brake components. (00319c) NOTES Install the primary bearing first using appropriate service manual and WHEEL BEARING REMOVER/INSTALLER. The side with the machined groove on the hub face is the primary bearing side for all kits except Kits 41681-07 and 40818-08. For Kit 41681-07: Install the wheel so that the hub markings are on the left side and the machined groove is on the right side of the motorcycle. • For 2006 and later FXDWG Models: When correctly installed, the tire will be 0.08-0.2 in (2-5 mm) off of center, compared to the fender. • For 2007 and later FX Softail and 2008 and later FXDWG Models: The left side of the wheel is the primary bearing side. • For 2006 and earlier FX Softail and 2007 and earlier FXDWG Models: The right side of the wheel is the primary bearing side. For Kit 40818-08: • Proper installation of this kit requires the separate purchase of two floating brake discs (44343-01 for 2004 – 2007 models and 44553-06A (stock) or 41500012 (polished) for 2008 and later models) and a tire (43371-07 on 2004-2008 models and 44026-09A on 2009-later models). The left side of the wheel has machined DOT markings to identify it as the primary bearing side. • For 2008 and later Touring: Install bearing shim (43903- 08) under the primary bearing. 3. Assemble wheel installation kit components and brake disc(s) to wheel, using the appropriate service parts table. Refer to FRONT WHEEL in service manual. 4. For FLSTC and FLSTN Models: Install wheel kit and right hand wheel spacer provided in installation kit. Refer to FRONT WHEEL in service manual. For FXSTD Models: Install wheel kit, stock wheel spacer and right side wheel spacer provided in installation kit in place of the tapered spacer discarded in Step 1. Refer to FRONT WHEEL in service manual. For FXSTS Models: Install wheel kit, stock wheel spacers and spacer provided in installation kit between the left side wheel spacer and the left fork. For all other models: Install previously removed wheel spacers. Refer to FRONT WHEEL in service manual. 5. Install front wheel (1), stock axle and stock axle nut. Refer to FRONT WHEEL in service manual. MAINTENANCE AND CLEANING Chrome parts must be maintained regularly to verify that they keep their original shine and luster. 1. Clean heavily-soiled wheel surfaces using Harley-Davidson Wheel and Tire Cleaner, applied with Harley Wheel and Spoke Brush. 2. Thoroughly clean chrome with a good quality chrome cleaner, such as Harley Bright Chrome Cleaner. 3. After cleaning and polishing, seal the finish with a good quality sealer, such as Harley Glaze Polish and Sealant

Incoming search terms:

KTM Front Wheel Bearing Installation Manuals

0

Filed Under (KTM) by admin on 31-01-2012

download
1 Place motorcycle on a stand so that the front wheel is off the ground. 2 Using a 27mm socket remove the front axle nut. Using a 10mm socket, loosen the four front axle pinch bolts. Slide front axle out of forks and remove front wheel. 3 Insert a long punch (with a good square edge) into the center of the aluminum wheel bearing spacers and push up against the inner edge of the spacer on the opposite side of the wheel (Fig. 1). Using a hammer, tap the punch around the entire circumference of the spacer until it completely slides out of the bearing (Fig. 2). Turn the wheel over and remove the other spacer in the same way. 4 Use a long screwdriver or narrow pry bar and pry the seals out of each side of the wheel (Fig. 3). 5 Using snap ring pliers, remove the bearing retaining snap ring from the brake rotor side of the wheel. (Fig. 4) NOTE: 2003 – CURRENT MODELS USING # 16-092 KIT DO NOT USE THIS SNAP RING. 6 Insert a long punch (with a good square edge) into the center of the wheel bearing, and push up against the inner edge of the bearing on the opposite side of the wheel. Using a hammer, tap the punch around the entire circumference of the bearing until it completely slides out of the hub. Turn the wheel over and remove the other bearing in the same way. NOTE: It may be necessary to tap on the punch sideways at first to knock the center aluminum sleeve off center so that you are able to get the punch on the edge of the bearing. 7 Clean areas where bearings will be inserted back into hub and apply a thin coat of grease around the machined hub surface. Tap the bearing on the snap ring (if used, either side if not) side of the hub into the machined hub surface, making sure to keep it square with the hub as it goes in and only tap on the outer race of the bearing. Once you get the bearing flush with the outer edge of the hub, use a socket or piece of pipe that is just smaller than the outside diameter of the bearing to finish tapping the bearing into the hub. (Fig. 5) 8 Install the bearing retainer snap ring (if used) into the groove machined in the hub, and then tap the seal in place over the snap ring with the spring on the seal in towards the center of the wheel. Tap in the aluminum spacer in the center of the seal.

Incoming search terms:

KTM Rear Wheel Bearing Installation and REMOVAL

0

Filed Under (KTM) by admin on 23-01-2012

download
1 Insert a long punch (with a good square edge) into the center of the aluminum wheel bearing spacers and push up against the inner edge of the spacer on the opposite side of the wheel (Fig. 1). 2 Using a hammer, tap the punch around the entire circumference of the spacer until it completely slides out of the bearing (Fig. 2). Turn the wheel over and remove the other spacer in the same way. 3 Use a long screwdriver or narrow pry bar and pry the seals out of each side of the wheel (Fig. 3). 4 Using snap ring pliers, remove the bearing retaining snap ring from either the disc or sprocket side of the wheel (Fig. 4). 5 Insert a long punch (with a good square edge) into the center of the wheel bearing, and push up against the inner edge of the bearing on the opposite side of the wheel. Using a hammer, tap the punch around the entire circumference of the bearing until it completely slides out of the hub. Turn the wheel over and remove the other bearing in the same way. NOTE: It may be necessary to tap on the punch sideways at first to knock the center aluminum sleeve off center so that you are able to get the punch on the edge of the bearing. 6 Clean areas where bearings will be inserted back into hub and apply a thin coat of grease around the machined hub surface. Tap the bearing on the snap ring side of the hub into the machined hub surface, making sure to keep it square with the hub as it goes in and only tap on the outer race of the bearing. Once you get the bearing flush with the outer edge of the hub, use a socket or piece of pipe that is just smaller than the outside diameter of the bearing to finish tapping the bearing into the hub. (Fig. 5)

Incoming search terms:

Honda 400EX Hub installation instructions

0

Filed Under (Honda) by admin on 20-12-2011

download
Remove all contents from its packaging and verify that all parts are present and free from damage. You should have the following items: (2) wheel hubs (2) smaller tapered bearings (2) large tapered bearings (2) wheel bearing nuts (2) dust caps (2) inner bearing seals (6) M3 x .5 screws (2) cotter pins (2) inner bearing spacers 2. Completely remove the old hubs from your quad and clean the spindle and the surrounding areas. It is very important to keep the new bearings and seals clean during installation for long life. Be sure to remove the factory inner bearing spacers from the spindle and discard. They will not be used in re-assembly. 3. Pack your new Timken tapered wheel bearings with a liberal amount of high quality wheel bearing grease. A wheel bearing packer works best, however you can accomplish the task by placing the grease in the palm of your hand and manually working it in between the bearing rollers. We also recommend that you pack the area between the bearing races in the hub with grease for additional lubrication and protection against moisture. 4. Place the large wheel bearing (inner) into the hub and install the inner seal. The seal should bottom out against the step in the bore and the face should be flush with the hub. 5. Remove the brake rotors from your old hubs. Re-install the rotors on your new hubs and be sure to use medium strength Loctite on the threads. 6. Apply a light film of grease or oil to the large diameter of the spindle stud. Install the new o-ringed bearing spacer onto the spindle. 7. Apply a thin film of grease to the seal surface on the bearing spacer and the inside diameter of the seal to prevent the seal from running dry. Install the hub onto the spindle and slide the outer bearing over the spindle and install the new bearing nut furnished with your hubs. Do not use the factory nut or washer. 8. SETTING THE BEARING PRELOAD: It is first necessary to seat the bearing before setting the preload. This aligns the rollers and prevents the bearings from loosening after a short period of use. To seat the bearing, tighten the spindle nut while you rotate the hub until the hub becomes difficult to spin. With the bearing now seated, you must set the bearing preload. Preload means placing a small amount of force against the bearings to remove any clearance between the bearing race and the rollers. This is done by backing the nut off completely and re-tightening it with your fingers. Do not rotate the hub while setting the preload . If a hole in the spindle is not accessible for installation of the cotter pin, adjust the nut tighter to bring a hole into alignment. Install the cotter pin and bend the pin around the outside of the nut. Do not attempt to bend the pin toward you (over the end of the spindle) or it may rub on the inside of the dust cap.

Incoming search terms:

HARLEY DAVIDSON FRONT DETONATOR WHEELS INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 10-03-2011

download
INSTALLATION 1. Remove existing front wheel assembly. Save axle, axle nut, brake disc and wheel spacers for kit installation. Discard moon-style hub cap on FLSTC and FLSTN models. Discard left side spacer on FXSTS models and tapered spacer on FXSTD models. Refer to FRONT WHEEL in Service Manual. Do not re-use brake disc screws. Re-using disc screws can result in torque loss and damage to rotor and/or brake assembly. (00319b) 2. See Figure 1. Install valve stem assembly (D) on wheel. Refer to TIRES in Service Manual. 3. Assemble wheel installation kit components and brake disc(s) to wheel, using the appropriate service parts table. Refer to FRONT WHEEL in Service Manual. NOTE Install primary bearing first using the applicable Service Manual and WHEEL BEARING REMOVER/INSTALLER. Kit 44550-07: The left side of the wheel has a groove machined in the hub to identify it as the disc side for installation, as well as the primary bearing side. The wheel should be installed so that the valve stem is on the right side of the motorcycle. Kits 44660-07 and 44661-07: The wheel should be installed so that the hub markings are on the left side of the motorcycle. An arrow engraved into the rim of 44661-07 indicates the direction of rotation. A groove is machined in the left-side hub face to indicate the primary bearing side. • Dual-disc models: Install the brake discs according to the Service Manual procedures. The Chrome hub cap (2) is not used. • Single-disc models: Install the brake disc according to the Service Manual procedures. Install the chrome hub cap (2) on the side opposite the brake disc. Kit 44660-07: The gross axle weight rating is unaffected by the installation of this wheel on a vehicle originally equipped with 21-inch wheels. Kit 44661-07: The gross axle weight rating is unaffected by the installation of this wheel on a vehicle originally equipped with 19-inch wheels. Kit 44552-08: The left side of the wheel has a groove machined in the hub to identify it as the left side for installation, as well as the primary bearing side. The wheel should be installed so that the valve stem is on the right side of the motorcycle. Kit 44556-07: The right side of the wheel has a groove machined in the hub to identify it as the right side for installa

HARLEY DAVIDSON SLOTTED 6-SPOKE FRONT WHEEL KITS INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 05-02-2011

download
INSTALLATION 1. Remove existing front wheel assembly. Save axle, axle nut, brake disc and wheel spacers for kit installation. Refer to FRONT WHEEL in Service Manual. For FLSTC and FLSTN Models: Discard moon-style hub cap. For FXSTD Models: Discard tapered spacer. 2. See Figure 1. Install valve stem assembly (D) on wheel. Refer to TIRES in Service Manual. Do not re-use brake disc screws. Re-using disc screws can result in torque loss and damage to rotor and/or brake assembly. (00319b) NOTES Install the primary bearing first using appropriate Service Manual and WHEEL BEARING REMOVER/INSTALLER. For Kits 43918-07 and 43919-07: • The side of the wheel with the valve stem and directional arrow is the right side of the wheel. • The left side of the wheel is the primary bearing side. For Kits 43920-08 and 43921-08: • The left side of the wheel has a machined groove in the hub face to identify it as the primary bearing side. • Install the wheel so that the valve stem is on the right side of the motorcycle. For Kits 44055-07, 44056-07, 44057-07, 44058-07, 43538-09, 43549-09 and 43577-09: • The wheel should be installed so that the hub markings are on the left side of the motorcycle. An arrow cast into the rim of Kits 44055-07, and 44056-07 indicates the direction of rotation. A groove is machined in the left-side hub face to indicate the primary bearing side. • For dual brake disc models, install the brake disc according to the Service Manual. The chrome hub cap (2) is not used. • For single brake disc models, install the brake disc according to the Service Manual. The chrome hub cap MAINTENANCE AND CLEANING Chrome parts must be maintained regularly so they keep their original shine and luster. 1. Clean heavily-soiled wheel surfaces using Harley-Davidson Wheel and Tire Cleaner applied with the Harley Wheel and Spoke Brush. 2. Thoroughly clean chrome with a good quality chrome cleaner, such as Harley Bright Chrome Cleaner. 3. After cleaning and polishing, seal the finish with a good quality sealer, such as Harley Glaze Polish and Sealant.

Incoming search terms:

AJS WHEEL BEARING ADJUSTMENT

0

Filed Under (AJS) by admin on 31-10-2010

download
Front Wheel (a) With the machine on the centre stand, disconnect the brake cable and remove the wheel. (b) Slacken the circular lock-nut (10). (c) Turn the adjusting sleeve (9) clockwise until all the slackness is just taken up. (d) Turn the adjusting sleeve (9) anticlockwise one-half a turn. It will now be necessary to drive the bearing back against the sleeve and this is done by:— (e) placing the wheel under a press and pressing the end of the spindle (on the brake-side) downwards. or: (f) jarring the end of the spindle on the brake-side with a weighty lead hammer. Whichever method is used the greatest of care must be exercised otherwise the bearing may be damaged, (g) Tighten the circular lock-nut (10). Hold the sleeve in position while this is being done otherwise the sleeve may move and the adjustment will be in- correct. (h) Refit the wheel and check for end-float. Front Wheel Bearing Assembly T www.ajs-matchles s.info ISSUED BY A·J·S MOTOR CYCLES, LONDON, S.E.18. Rear Wheel Bearing Assembly for Quickly Detachable Wheels Rear Wheel (a) Disconnect the speedometer driving cable. (b) Remove the lock-nut (16) which secures the speedometer-drive gear­ box in position. (c) Remove the wheel. (d) Grasp the speedometer-drive gearbox (15) with the fingers and firmly pull it away from the hub. (e) Proceed as described in the instructions for the front wheel (b) to (d). Note that in the illustrations for the rear wheel the circular lock-nut is (13) and the adjusting sleeve is (14), It will now be necessary to drive the bearing back against the sleeve and this is done in the following manner: Quickly Detachable Wheels (f) place the wheel under a press, brake- side uppermost, and apply pressure to the oil-seal distance piece (6), or; (g) jarr the end of the oil-seal distance piece (6) with a weighty lead hammer. Whichever method is used the greatest of care must be exercised otherwise the bearing may be damaged. Wheels for Rigid-Frame Models (h) Remove the brake-side spindle nut (19), washer (18), fork-end spacer (17), outer spacer (20), and the brake plate (21). (i) Place the wheel, brake-side uppermost. under a press and apply pressure to the oil-seal distance piece (6). or; (j) jarr the end of the oil-seal distance piece (6) with a weighty lead hammer. Whichever method is used the greatest of care must be exercised otherwise the bearing may be damaged. All Rear Wheels (k) Refit the speedometer-drive gearbox. It is pushed on. The two dogs must engage with the slots in the end-face of the adjusting sleeve. (l) Refit the lock nut (16). (m) Refit the wheel into the frame and check for end-float. (n) Tighten the lock-nut (16) and refit the speedometer driving cable

Incoming search terms:

ESCAPADE TRAILER Wheel Bearing Removal AND OWNER'S MANUAL

0

Filed Under (Tips and Review) by admin on 20-11-2010

download
1. Remove lug nuts and wheel assembly. Remove the cotter pin, adjusting nut (castle nut) and washer from the wheel spindle. 2. Pull the wheel hub towards you to loosen the outer bearing cone. Don’t Let the cone fall to the ground. As the hub is removed, the inner bearing and grease seal will come with it. Observe which direction the inner seal is facing. Pry out the inner seal and discard. 3. Remove all old lubricant from the hub assembly and wheel spindle with kerosene or mineral spirits. CAUTION: do not use gasoline to clean and remove the old lubricant). Inspect the spindle for scoring, bending, thread or other damage. A light grease coating on the spindle will make bearing installation easier and prevent rust from forming. 4. Inspect cups in the hub for pitting, metal flaking, scoring, rust or other obvious damage. Remove any damaged cups with a mild steel bar. Replace cups and cones in matched sets only; not one at a time. 5. Use cup driver or mild steel bar to press or drive the new cup into the hub Wheel / Rim: 12 X 4 JA (4 bolt, 4″ bolt diameter, 2½” rear space) Tire: 4.80 X 12 (B) (4 ply rated; cold pressure rated to 465 lbs. of load at 25 PSI). NOTE: These are standard utility trailer size tires and wheels. Using oversize tires or increasing tire pressures to a level higher than recommended will not increase the Gross Vehicle Weight Rating (GVWR). HUBS For maximum performance from your Sport Wheels and to avoid damage to your trailer, observe the following precautions: •When buying a replacement hub, check that the hub flange is no smaller than a diameter of ?”. •The replacement hub must accept the 1″ bearing (Part Number L44643) and matching cup. •Torque all lug nuts holding the wheel to 75 ft. lbs. TRAILING ARM / SWING ARM No maintenance is required for the trailing arm bearings for the life of the trailer. However, if the trailing arm is removed for any reason the following steps must be followed. 1. Once the ¾” X 16 hex nut has been removed, discard it, and replace with a new lock nut of the same design. 2. When replacing the trailing arm, be sure the bearing spacer is located between the bearings. 3. Torque the hex nut to 14 ft. lbs while moving swing-arm up and down.. DO NOT BACK OFF FOR ADJUSTMENT . Insufficient torque to the

Incoming search terms: