best place to ground amp on 2012 ultra classic

You search Auto repair manual PDF best place to ground amp on 2012 ultra classic, if there are search results will appear below. If search results do not exist, please search by others keyword.





Victory Freedom Engines Installation Instructions for S&S Air Cleaner Kit

0

Filed Under (Victory) by admin on 31-10-2010

download
1-Locate and remove the Intake Air Temperature Sensor (IATS) from the stock Polaris Victory air box. Locate the new position for the IATS on the bottom of the S&S air cleaner. Push the IATS in the lower air cleaner cover and turn1⁄ 4 turnin either direction, make sure you feel it lock into place. Inspect from the inside of the air cleaner to ensure that the barbs are locked into place. See Picture 1. 2-Using the stock Polaris Victory air box gasket (PN 5811908) and S&S supplied (Qty 4) M6 fasteners, assemble the lower air cleaner cover to the throttle body using 243 Blue Loctite®on the treads. Torque the M6 fasteners to 72-96 inch pounds. 3-Position the S&S pre-formed air filter onto the lower air cleaner cover ensuring that it fits into the machined groove. 4-Install the top air cleaner cover on top of the filter ensuring that it fits into the machined groove. 5-Make surethat the filter is situated in the machined grooves on both the top and bottom air cleaner covers. 6-Using 243 Blue Loctite on the threads of the S&S supplied (Qty 3) M6 fasteners tighten down top air cleaner cover evenly until seated. Finish torque the fasteners to 72-96 inch pounds. Now you’re ready for breather hose and barometric pressure hose routing. 7-Locate the S&S supplied 3⁄ 16 “reinforced hose and clamps. Push one end of the hose on the 3⁄ 16 “brass barb in the bottom air cleaner cover and slide clamp up around the end of the hose. The other end of the hose is for the Barometric Pressure Sensor (MAP). Route the hose towardthe back of the engine over the top of the rear rocker cover. 8-Remove the MAP sensor from the stock Polaris Victory air box. Remove the orange rubber gasket from the MAP sensor. Slide the S&S supplied clamp over the 3⁄ 16 “rubber hose that leads to the air cleaner. Push the barbed end of the MAP sensor into the 3⁄ 16 ” rubber hose and slide clamp up to the end of the hose around the barb. A small amount of lubricant may be applied to the barb on the MAP sensor to make installation easier. 2 S&S Air Cleaner Assembly 41-0021 (Calibration cardnot shown) Picture 1 CAUTION WARNING WARNING Plastic barb locked in recess.
9-Assemble and install breather hose as follows: A-Cut the stock Victory®hose on the straight section just behind the 90 degree bend as shown in Picture 2 . B-Slide an S&S supplied 1⁄ 2 “hose clamp over the modified stock breather hose. C-Install the S&S straight barb in Victory breather hose and position a hose clamp around hose end. D-Slide the 90-degree end of breather hose over the brass barb on the air cleaner cover and slide hose clamp in place. E-Position straight end of the S&S breather hose over the 1⁄ 2 “barb to connect to the Victory hose. Slide clamp over connection. F- See Pictures 3 and 4 for breather hose and barometric pressuresensor hose installation positions. NOTE: S&S breather hose can be cut for best fit

Incoming search terms:

HARLEY DAVIDSON ULTRA CLASSIC AND ELECTRA GLIDE CLASSIC TOUR PACK ADJUSTMENT KIT INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 23-04-2012

download
1. Open the Tour Pack and remove all of the contents. 2. Remove map bag and inner pack liner. Pack liner comes out quite easily once map bag is removed. 3. Remove the 4 bolts inside the tour pack that are located on top of the metal support plate that hold the tour pack to the luggage rack. Have your assistant hold the pack in place before removing the last bolt. 4. Gently tip the tour pack forward to expose the supporting luggage rack under the pack. 5. While your assistant holds the pack up, place the two adjusting bars on top of the supporting luggage rack. Use the 4 flat head screws supplied with the kit to mount the bars snugly to the support rack (see fig. 1). 6. Reposition the tour pack over the threaded holes in the adjusting bars at the 2″ or 3″ position and bolt it in place snugly (see fig. 2). 7. Replace the trunk liner and map case and the installation is complete

Incoming search terms:

2002 URAL Classic Motorcycles BC-75 (Bavarian Classic) LC-75 (Luxury Cruiser) Tourist, Adirondac & Patro Owner's Manual

0

Filed Under (Ural) by admin on 02-11-2010

download
Front brake control lever (Fig.1, #5). When the lever is squeezed, the front wheel brake is actuated. The front brake should be used together with rear brake. When the brake lever is squeezed, the stop signal lamps are switched on. Kick lever (Fig.1, #11) is designed to start the engine. On pressing the lever the crankshaft of the engine is actuated through the gearbox. The lever is returned to its initial position by the spring inside the gearbox. Note: this is a backup to the electric starter. Gear shift foot pedal (Fig.1, #12) is a two-arm type. When the front arm is pressed, shifting from high to lower gears takes place. When the rear arm is pressed, shifting from low to higher gears takes place. Since the heel-toe shift lever is short-coupled, you will find it easier to shift up if you rotate the heel of your left foot in towards the rear arm before stepping on it with your heel. The neutral position is fixed between the I and II gears. Speedometer is on the dash board, with trip (Note..BC-75 has no trip odometer) and total odometer. The trip odometer is reset to zero by rotating push-button (Fig.1, # 3) counterclockwise. Note that the odometer reads in kilometers not miles. Ignition Switch (Fig.1, # 19) has three fixed positions of the key. The position and switching diagram of the ignition locks are shown above.
18 The indicator lamps are mounted on the instrument board: (Fig. 1, # 2) — turn indicator pilot lamp, (orange) (Fig. 1, # 4) — gearbox neutral and reverse gear engagement, (green) (Fig. 1, # 18) — head lamp high beam indicator, (dark blue) (Fig. 1, # 20) — alternator fault indicator lamp, (red) Note: If the red alternator fault light stays on continuously during normal operation above approximately 1500 RPM, there is a problem with the charging system or battery. Throttle Control (Fig.1, # 6) is on the right handlebar. Turning the twist grip counterclockwise increases engine speed. Ignition Cutoff Switch (Fig.1, # 7) has two positions, ignition off (up), and ignition on (down). Low and High Beam Light Switch (Fig.1, # 15), turn indicator switch (Fig.1, #13) and horn push-button (Fig.1, # 14) are combined in one unit on the left-hand handle bar control housing. Master Battery Switch (Fig.1, # 21) is under the seat. Electric Start Button (Fig. 1, # 8) is located on the right-hand twist grip, below the kill switch. The Steering Damper absorbs lateral kicks on the front wheel. Turning tightening bolt (Fig.1, # 17) clockwise increases friction. This can be used while riding over bad roads

2009 Kawasaki ULTRA 250X/ 260X FUEL INJECTION CONTROLLERS And REGULATORS INSTALLATION MANUAL

0

Filed Under (Kawasaki) by admin on 25-10-2010

download
The R&D high performance Air Filter Kit will improve acceleration and top speed performance by increasing air flow and reducing air temperatures that enter directly into the Ultra 250X’s air plenum box area. The O.E.M. air plenum box on the Ultra 250X is a great design that will flow plenty of air. However, the air that feeds the plenum box is heated by the engine. R&D has created an easy to install “flat filter” that installs directly in place of the large center access inspection cover located directly under the main glove box. The R&D Flat Air Filter insert will allow unrestricted fresh and cool air to enter the air plenum box area which will add power you can feel and a nice high performance tone. The R&D Performance Filter Kit also features two filters, one for each of the surge and blowoff protections valves. The O.E.M. surge valve recycles compressed hot air back into the air box plenum at idle and under deceleration conditions. The R&D surge and blowoff valve filter kit removes the air recycling hoses which will keep the hot air from entering the air plenum box reducing the engines intake air temperatures. The R&D Ultra 250X Air Filter Kit offers great performance tips on how to remove the restrictive air vent hoses which will further reduce the under seat ambient air temperatures. The R&D Filter system does not remove or alter the O.E.M. plenum box in any way, therefore there are no questions to be answered regarding water ingestion

Incoming search terms:

MULTI-APPLICATION AIR HORN INSTALLATION INSTRUCTIONS

0

Filed Under (Tips and Review) by admin on 27-10-2010

download
COMPRESSOR MOUNTING: Find a suitable location to mount the compressor. Under the seat, fuel tank or one of the side covers is the most concealed place. Mount the compressor using the supplied large hose clamp, long cable ties or bolt & nut. NOTE: Keep the compressor terminals pointing downward or horizontal. Locate and area that will be protected from water & dirt. Attach air hose to compressor. HORN MOUNTING: Mount horns to the frame or engine guards only. The most common place is the left front frame down – tube, below the fuel tank using the “L” bracket with the hose clamp routed through the slots. (See photos 2 & 3) If necessary you can bend or twist the bracket using a vise or two adjustable wrenches. Horns should be horizontal or slightly downward. They may be mounted on the right side by reversing the long and short trumpet. Flipping the bracket that mounts to the horns 180 degrees can do this. Route the hose from the compressor to the horns, cut to length & attach. Spraying WD-40 to the end of the hose helps ease assembly. Use a small flame to heat seal the hose outer braided cover to keep from fraying. WIRING: (see photo 1 & the wiring diagram) when mounting the relay be sure the terminals are pointed downward. Remove wires from the stock horn & attach to relay terminals 85 & 86. Find an inconspicuous place to mount the relay. Attach using supplied cable tie being sure the terminals are downward. Refer to diagram & make connections as shown using the supplied wire & terminals. Route wire neatly & wire neatly & where possible hidden. Cable tie the wire to secure. Turn on ignition & push horn button to test. HELPFUL HINTS: When routing wire or hose under fuel tank or difficult to reach place use a stiff piece of wire such as a coat hanger about 3′ or 4′ long for a helpful tool. Bend a small loop at one end. Push wire tool through, attach wire or house with tape and pull back through

Dazon Raider Classic 150 (Oil-cooled & Internal Gearbox): Service Manual (single/ double-seat)

0

Filed Under (Dazon) by admin on 30-11-2010

download
1.2.1 Fuel Please use the gasoline of SAE 90# or above. Also we recommend you to use the unleaded gasoline. 1.2.2 Engine Oil Please use the high-quality engine oil of SAE 10w/30SF. 1.3 Break-in Procedure For your first 2 hours of riding, don’t exceed 2/3 throttles. Vary the engine speed for the first 5 hours. Never hold the engine at full throttle for long periods of time. Raider-Classic 150 (Oil-cooled&Internal Gearbox): Service Manual (single/ double-seat) EEC Version;3.0 Feb..2005 5 1.4 Specifications DIMENSIONS SINGLE-SEAT / DOUBLE-SEAT Overall Length 2330mm / 2300mm Overall Width 1310mm / 1460mm Overall Height 1425mm / 1425mm Wheelbase 1475mm / 1520mm Ground Clearance 200mm VIN Accord with GMVR A01-01 Statutory Plate& Safety Labels Accord with GB 7258-1997 ENGINE Model DZ1P57QMJ Type Oil-cooled, single cylinder, 4-Stroke Engine Capacity 150cc Displacement 149.6ml Bore X Stroke 57.4mm X 57.8mm Max Power 7.0kw or 7000r/m Max Torque 10.0N.m or 6500 r/m Idle Speed 1700 ± 100 r/m CO Emission 7.0g/km HC Emission 1.0g/km Fuel Type SAE 90# or above (unleaded) Lubricate Oil Type SAE 10W/30SF Lubrication Force & Splash Cooling Oil-cooled Ignition C. D. I. Starting Electric Spark Plug C7HSA (NGK) Spark Plug Gap 0.6~0.7mm Transmission Chain Transmission Gearbox Transmission Ratio F.:7.8:1 ; B.:11.297:1 Compression Ratio 9.5 ± 0.1 : 1 Carburetor MIKUNI BS 24-1005 Absorber Normal (in 10 5 times of experiments) CAPACITIES Front/ Rear Tire Load Coefficient 36 Front/ Rear Tire Speed Level L Fuel Tank 7.0L, 130kpa (no leakage in experiments) Engine Oil 1000ml Gear Oil 200ml Starting Time ≤15s Climbing ≥20%

INSTRUCTIONS ON HOW TO R & R YOUR Swingarm

0

Filed Under (Tips and Review) by admin on 12-12-2010

download
• Upgrade Your Pre- 2002 FL Or FXR Rear Fork & Get Rid Of The Crappy & Dangerous (Cleve Blocks) & Replace Them With A Stable System. • R & R your Swing Arm, Belt Drive, Swing Arm Pivot Shaft, and Rear Wheel. The paragraphs below are a photo journey into the replacement of a FL or FXR swing arm. To upgrade the pre 2002 FL, here is a How-To on cheaply replacing the poor parts Harley stuck you with. Now – Let’s Get Er’ Done • Pre- 2002 had weak swing arms and are known to fail. The cleve blocks are the cause of “Rear Steer” or “Rear Fork Deflection”. Harley came up with a patch in 2002, using bearings. Because the pre 2002 transmissions have a 5/8″ mounting hole for the 5/8″ swing arm pivot shaft, a conversion unit has been made. No transmission removal for boring is necessary. Under no circumstances, do I recommend drilling out the transmission case with a hand drill. The drill will “wander” (drift)! • Solution: Go to either a trike shop/manufacturer, e-Bay, or shop and buy a new style swingarm. Harley made an additional upgrade in 2007, try and buy this type 2007 & above). If upgrading to a 2008, Harley use 25mm (smaller than 1″) axles & wheel bearings, you will have to use 25mm bearings. With that said, let’s get on with it. • In the case of a 2007 swingarm; buy and do not pay over $40 for the swing arm and axle. You must use the corresponding axle as a ¾” axle set-up is different (along with wheel bearings & spacers). You positively can not use a pre -2002 HD stock wheel because the wheel bearing spacer will fit into the wheel. Buy 2002 & above style wheels as they (9 spoke) are cheep. • You are going to have to either bore out your stock rear caliper bracket or better still, upgrade your whole rear brake to the new model & sell yours on e-Bay. • I recommend doing the following before hand and have it ready for installation; Remove bearings et al. from the 2002 & later swing arm via press. Bike Work: • Jack up your bike using a center jack. Secure the bike so it will not fall over. You can also use a motorcycle jack. I use a motorcycle dolly

1990 Harley Davidson ULTIMA 6 SPEED BUILDERS KIT INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 09-04-2012

download
For 2000 & later models removal of approximately 1/4 of an inch off of the shifter arm bushing is likely required. Doing so will allow installation of the retaining clip & washer onto the shifter arm. It is good practice to double check how much material should be removed before cutting the bushing. See fig. 1 & 2 Install supplied Main drive gear bearings & countershaft needle bearings using special tool # 97-164 NOTE: Lightly coat bearings with assembly lube or gear oil for easier installation. Install supplied Main drive gear retaining clip & verify that it is fully seated and cannot come out. Do not re-use old bearings or retaining clip. Install supplied Main drive gear into bearings using special tool # 97-166 See fig. 3 Install supplied trap door gasket & verify that it is on correctly. Install supplied 6 speed gear set making sure to align the countershaft with the needle bearing assembly. Slowly slide in gear set until the mainshaft & countershaft will not slide in any further. Lightly tapping on the trap door (while verifying that there is no interference) with a soft blow hammer will then fully seat the shafts & trap door. See fig. 4 Once gear set is installed use the supplied 5/16-18×1-1/2 & 1/4-20×1-1/2 bolts to secure the trap door. Torque the 5/16 bolts to 15 ft-lbs w/ red loctite (high strength) Torque the 1/4 bolts to 9 ft-lbs w/ red loctite (high strength) See fig. 5 FIG. 1 FIG. 2 FIG. 3 FIG. 4 FIG. 5 2 FIG. 6 At this time check to make sure all gears rotate freely & that all slider gears slide with no interference. Lightly lube & install supplied quad seal onto main drive gear. See fig. 6 Install Main seal using special tool # 97-164. See fig. 7 Install original spacer onto mainshaft. NOTE: Beveled side goes in towards quad seal. See fig. 8 Install supplied transmission drain plug & supplied speedo sensor plug with gasket. Install supplied shifter forks onto appropriate slider gears. See fig. 9 Lightly lube & install supplied shift fork shafts. NOTE: Short shaft is installed from the right side with the threaded hole facing out. Long shaft is installed from the left side & should not protrude from the right side of case. See fig. 10 Install supplied shift fork shaft allen head plugs. (Use red loctite to prevent movement of plug & to aid in sealing)

Harley-Davidson S&S Super E and G Series Shorty Carburetors Installation and Jetting Instructions

0

Filed Under (Harley Davidson) by admin on 24-10-2010

download
throttle linkage with no cable modification. S&S Super E and G carb kits for 1936 to 1989 Big Twins contain a throttle cable guide (11-2339) designed for butterfly type throttle cables, and kits for 1990 and later Big Twins contain a taller throttle cable guide (11-2338) designed for CV type throttle cables. See Picture 2. The two throttle cable guides are interchangeable on the carburetor body, and can be changed very easily to update older carburetors or to accommodate custom throttle cables which are not stock for a particular year chassis. 1981 to Present Sportster Models Stock Sportster models from 1981 to 1987 have two cable throttle system designed for butterfly type carburetors. Sportsters from 1988 to present have a two cable throttle system designed for use with the stock constant velocity (CV) type carburetor. Since the taller #11-2338 cable guide bracket can not be used on a Sportster chassis due to insufficient frame clearance, throttle cables on Sportsters originally equipped with a CV type carburetor must be changed to butterfly style cables. S&S can supply the correct style throttle cables. See S&S Throttle Cable Application Chart. Picture 2 S&S THROTTLE CABLE APPLICATION CHART Length Total Housing Length Vinyl Housing Part Number Open Side Part Number Close Side Fitment 36″ 32″ #19-0430 #19-0431 For Buell with 7/8″ handlebars 36″ 32″ #19-0432 #19-0433 To ’95 ’81-’85 FX and FL; All ’81-’85 XL (Also pre-’81 w/2-cable throttle housing replaced.) For Buell with 1″ diameter handlebar 36″ 32″ #19-0436 #19-0437 ’96-Up 883-1200 XL 39″ 35″ #19-0434 #19-0435 To ’95 Softail (FXSTC, FXST, FLSTC, FLSTF) ’86-’94 FXR, ’93-’95 Dyna 39″ 35″ #19-0438 #19-0439 ’96-Up Softail (FXSTS, FXSTC, FLSTC, FLSTF) ’96-Up Dyna 42″ 38″ #19-0446 #19-0447 To ’95 custom application 42″ 38″ #19-0440 #19-0441 ’96-Up custom application 48″ 44″ #19-0462 #19-0463 To ’95 All FLT Models 48″ 44″ #19-0464 #19-0465 ’96-Up All FLT Models ” 1996 to Present Buells 1996 and 1997 Buells require special S&S butterfly style throttle cables for Buells, which are compatible with the stock 1996-1997 throttle assembly. 1998 and later carburated Buells require installation of stock 1996 – 97 throttle grip and the special S&S Buell style throttle cables when installing Super E or G carburetors. S&S Throttle Kits S&S throttle kits fit 1″ handlebars and can be used on most chassis. (An adapter sleeve is available for use with earlier, 7 ⁄ 8 ” OEM handlebars originally equipped with internal throttle cable.) Barrel fittings on S&S cables readily “plug in” to S&S Super E, G, and stock H-D 1981-’90 butterfly type carb throttle linkage. Kits include one opening and one closing side cable, left and right grips, and handlebar clamps. Kits with 36″, 39″, 42″, or 48″ length cables are available. Length specified refers to overall cable length. Vinyl covered outer housing is 4″ shorter than overall length

Incoming search terms:

THUNDERJET INSTALLATION FIXTURE for S&S CARBURETORS

0

Filed Under (S&S) by admin on 31-10-2010

download
FUEL DELIVERY TUBE 6 5 6 5 6 5 6 5 -A Ambe -A Ambe r rton Drive, Elkridg e, MD 21075 410-579-2828 e, MD 21075 410-579-2828 ton Drive, Elkridg Using the two ¼”- 20 cap screws provided, secure t carb body at air cleaner surface to fixture through h # 2 & 5 . NOTE: Holes # 2 & 6 may be used to angle th ThunderJe clearance is needed below the fuel tank. he oles e t farther forward if additional ADJUSTABLE AIR BLEED les # RIGINAL AIR Secure Carb to fixture using ho & 8. 1 O LEED B BLOCKING Secure C fixture using ho & 6. arb to les # 1 BOWL VENT RELOCATION Secure Carb to fixture using holes # 6 & 7 . FLOAT BOWL ee Reverse side for S&S ‘B’ & ‘D’ Secure float bowl to fixture using the 3/8″- 16 flange nut and threaded rod provided using the 20 degree slope. S instructions. S&S ‘B’ & ‘D’ CARBS EXTERNAL BOWL VENT 6 5 6 5 6 5 6 5 -A Amberton Drive, Elkridge, MD 21075 410-579-2828 -A Amberton Drive, Elkridge, MD 21075 410-579-2828  ADJUSTABLE AIR BLEED THUNDERJET FUEL TUBE :00 position, viewed facing air filter (9 surface) sing the two #10-24 cap screws provided, :00 position, viewed facing air filter U secure the Carb body at bowl surface to fixture through the two holes marked ‘B’ . (3 surface) Using the two #10-24 cap screws provided, FLOAT BOWL secure the Carb body at bowl surface to fixture through the two holes marked ‘D

Incoming search terms: