best repacement parts for swingarm 2005 harley ultra classic

You search Auto repair manual PDF best repacement parts for swingarm 2005 harley ultra classic, if there are search results will appear below. If search results do not exist, please search by others keyword.



  best repacement parts for swingarm 2005 harley ultra classic Direct Download speed 5282 Kb/s

  best repacement parts for swingarm 2005 harley ultra classic Full Version speed 6162 Kb/s



HARLEY DAVIDSON ULTRA CLASSIC AND ELECTRA GLIDE CLASSIC TOUR PACK ADJUSTMENT KIT INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 23-04-2012

download
1. Open the Tour Pack and remove all of the contents. 2. Remove map bag and inner pack liner. Pack liner comes out quite easily once map bag is removed. 3. Remove the 4 bolts inside the tour pack that are located on top of the metal support plate that hold the tour pack to the luggage rack. Have your assistant hold the pack in place before removing the last bolt. 4. Gently tip the tour pack forward to expose the supporting luggage rack under the pack. 5. While your assistant holds the pack up, place the two adjusting bars on top of the supporting luggage rack. Use the 4 flat head screws supplied with the kit to mount the bars snugly to the support rack (see fig. 1). 6. Reposition the tour pack over the threaded holes in the adjusting bars at the 2″ or 3″ position and bolt it in place snugly (see fig. 2). 7. Replace the trunk liner and map case and the installation is complete

Incoming search terms:

HARLEY DAVIDSON CHROME 1.25 INCH (31.75 MM) DIAMETER HANDLEBAR KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 10-03-2011

download
CHROME 1.25 INCH (31.75 MM) DIAMETER HANDLEBAR KIT GENERAL Kit Number 56032-08 Models For model fitment information, see the P&A retail catalog or the Parts and Accessories section of www.harley-davidson.com (English only). This kit does not fit models equipped with a hydraulic clutch, handlebar mounted gauges or the Road Tech® Radio. Additional Parts or Accessories Required Separate purchase of additional parts or accessories is required for proper installation of this Handlebar Kit on this model motorcycle. Please see the P&A retail catalog or the Parts and Accessories section of for a list of required parts or accessories for this model. For Australia, Brazil, England, Europe and Japan, two special screws (Part Number 2935A) will also be required. Tools and Supplies Required Loctite® 271 Threadlocker and Sealant – Red (H-D Part Number 99671-97) is required for the proper installation of this kit. Fresh, uncontaminated DOT 4 brake fluid from a sealed container will also be needed. Replace brake line gaskets. Re-using original gaskets can cause brake failure and loss of vehicle control, which could result in death or serious injury. (00318a) For models that retain the original brake line, the two brake- line gaskets found at each banjo fitting must be replaced . Refer to the appropriate parts catalog or see a Harley-Davidson dealer for the correct part numbers. Motorcycles equipped with a glued left-side hand grip will also require a new grip, sold separately. Refer to the parts catalog for replacement stock hand grips. Ask a Harley-Davidson dealer about the selection of Genuine Motor Accessory hand grips that are available. The rider’s safety depends upon the correct installation of this kit. Use the appropriate service manual procedures. If the procedure is not within your capabilities or you do not have the correct tools, have a Harley-Davidson dealer perform the installation. Improper installation of this kit could result in death or serious injury. (00333a) NOTE This instruction sheet references service manual information. A service manual for this year and model motorcycle is required for this installation and is available from a Harley-Davidson dealer. Kit Contents See Figure 6 and Table 1. INSTALLATION Preparation To prevent accidental vehicle start-up, which could cause death or serious injury, disconnect battery cables (negative (-) cable first) before proceeding. (00307a) Disconnect negative (-) battery cable first. If positive (+) cable should contact ground with negative (-) cable connected, the resulting sparks can cause a battery explosion, which could result in death or serious injury. (00049a) 1. Refer to the service manual and follow the instructions given to remove the seat and disconnect the battery cables, negative cable first. Retain all seat mounting hardware. Direct contact of D.O.T. 4 brake fluid with eyes can cause irritation. Avoid eye contact. In case of eye contact flush with large amounts of water and get medical attention. Swallowing large amounts of D.O.T. 4 brake fluid can cause digestive discomfort. If swallowed, obtain medical attention. Use in well ventilated area. KEEP OUT OF REACH OF CHILDREN. (00240a) D.O.T. 4 brake fluid will damage painted and body panel surfaces it comes in contact with. Always use caution and protect surfaces from spills whenever brake work is performed. Failure to comply can result in cosmetic damage. (00239b) NOTE Immediately wipe up any brake fluid spillage with a clean, dry, soft cloth. Follow up by thoroughly wiping affected area with a clean, damp, soft cloth (small spills) or washing with a large quantity of soapy water (large spills)

Incoming search terms:

HARLEY DAVIDSON BLACK ENGINE GUARD KIT REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 24-02-2011

download
REMOVAL NOTE This Instruction Sheet covers several different Harley-Davidson models and years. Be sure to locate and follow the procedures that apply to the motorcycle receiving the new guard. For Models without Lower Fairings 1. Proceed to For All Models section. For Model FLHTCUI (Ultra Classic Electra Glide) with Factory-Installed Lower Fairings 1. Remove the lower fairings following the instructions in the appropriate Service Manual. 2. When the lower fairings have been removed, proceed to For All Models section. For Models FLHR/I (Road King), FLHT (Electra Glide Standard) or FLHTC/I (Electra Glide Classic) with Harley-Davidson Genuine Motor Accessory Lower Fairings 1. See Figure 1. Remove the two black screws (1) that attach the fairing cap (2) to the lower fairing (5). Remove the cap. Set the parts aside for re-installation. 2. Remove the screw (7), rubber washer (8) and locknut (10) and the clamp (9) that attaches the bottom of the lower fairing to the engine guard and set aside. 3. Remove the two locknuts (3), U-bolt (6) and U-bolt retainer (4). 4. Remove the lower fairing by sliding it out from behind the engine guard. 5. Repeat Steps 1 through 4 for the opposite side. 6. Proceed to For All Models section. For Model FLTR/I (Road Glide) with Harley-Davidson Genuine Motor Accessory Lower Fairings Disconnect negative (-) battery cable first. If positive (+) cable should contact ground with negative (-) cable connected, the resulting sparks can cause a battery explosion, which could result in death or serious injury. (00049a) 1. Disconnect the battery, negative (-) battery cable first, following the instructions in the appropriate Service Manual. 2. Remove the seat following the instructions in the appropriate Service Manual. 3. Remove the cable strap holding the clutch cable to the engine guard. 4. See Figure 2. Remove the TORX screw (8), rubber washer (9) and locknut (11) and the clamp (10) that attaches the bottom of the lower fairing (4) to the engine guard and set aside INSTALLATION 1. Hold the engine guard in position, and loosely fasten the top of the guard with the new hex socket screw and flat washer from the kit. 2. Install the bottom brackets to the motorcycle frame with the two new TORX screws and locknuts. 3. Tighten all three screws to 15-20 ft-lbs (20.3-27.1 Nm) . For Model FLHTCUI (Ultra Classic Electra Glide) with Factory-Installed Lower Fairings 1. Install the lower fairings following the instructions in the appropriate Service Manual. For Models FLHR/I (Road King), FLHT (Electra Glide Standard) or FLHTC/I (Electra Glide Classic) with Harley- Davidson Genuine Motor Accessory Lower Fairings 1. Carefully place one lower fairing in position from behind the engine guard. 2. See Figure 1. Install the lower fairing to the top of the new engine guard with the U-bolt (6) from the back, through the holes at the top of the fairing. Install the retainer (4) in position on the U-bolt and secure to the engine guard with the two locknuts (3). Do not tighten the locknuts at this time. 3. Attach the bottom of the fairing to the engine guard with the clamp (9) removed earlier. Install the clamp around the engine guard in the direction shown, with the tabs toward the rear of the vehicle and the flat side of the clamp against the lower fairing. Insert the screw (7) through the lower fairing, rubber washer (8) and clamp (9). Secure the assembly with the locknut (10). Tighten to 12 ft-lbs (16.3 Nm) .

Incoming search terms:

Harley Davidson FL series Electra Glide, Ultra Classic, Road King, Road Glide Left and Right Mounting Plate Installation Installation Manual

0

Filed Under (Harley Davidson) by admin on 25-02-2012

download
Remove existing control arm end cap and grind the outside flush. See picture below for reference. The swing arm will drop if both sides are removed at the same time. To ease installation, complete one side before starting on the other. Note: there is a left and right. Left and right end caps shown. 2. Install mounting plate assembly 10002351 on top of the end cap using 7/16″ hex head bolt and lock washer in the bottom hole. Use the 7/16″ counter sink bolt in the top hole. Make sure the end cap is seated properly. The end cap notch should fit into the recess on the frame. The pivot arm assembly is shipped on mounting plate assembly; you may remove the pivot arm to make installation easier. 3. Snug up the bolts evenly, make sure the end caps are not crooked in relation to the frame. Tighten both bolts to 25 ft lbs. (Further tightening will be required after the toe in is set). 4. If you removed the left hand pivot arm assembly, remount it now, 10002575-A (pg 20) with seal, bearings (2), washer, nut, cotter pin and dust cover. 5. Repeat for right hand side. 5 Toe In Adjustment Adjustment made with the mounting plates, bolts, pivot arms, and hubs (without wheels and tires) in place

Incoming search terms:

Harley Davidson Shift leverbracket INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 24-03-2012

download
Installation of any parts should be performed by a qualified, trained mechanic. • All parts included in the Rocker Boards™Conversion Kit are intended to be used as sold. Modification of any part will void all warranties. • Installation should be performed on a motorcycle that is completely cool to avoid burns or other injuries. • Refer to a specific authorized Harley-Davidson service manual for correct disassembly and reassembly procedures for any parts that need to be removed to facilitate installation. • Motorcycle exhaust fumes are toxic and poisonous and must not be inhaled. Always run motorcycle in a well-ventilated area. • Do not perform any installation steps under the influence of alcohol, drugs, or if feeling fatigued. Warranty Briggs Made Cycle Parts, Inc. Rocker Boards™and all parts included in the conversion kit are warranted to the original purchaser to be free of manufacturing defects in materials and workmanship for a period of one (1) year from the original date of purchase. Any part that fails to conform to these conditions, will be repaired or replaced at the discretion of Briggs Made Cycle Parts, Inc. upon receipt of the defective part within the one year warranty period. In the event a part has been rendered defective, Briggs Made Cycle Parts, Inc. must be notified prior to the return of the defective part. Briggs Made Cycle Parts, Inc. will not be liable for any consequential or incidental damages resulting from the failure of any part, the breach of any warranties, the failure to deliver, delay in delivery or any other breach of duty between Briggs Made Cycle Parts, Inc. and a customer

HARLEY DAVIDSON SOFTAIL SWINGARM PIVOT COVER KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 10-04-2011

download
INSTALLATION 1. Use rubbing alcohol to clean the swingarm surface, pivot bolt, and nut. 2. Place the larger left-side pivot cover (3) over the pivot nut. Position the set screw (4) at the bottom of the cover. Tighten set screw to 16 in-lbs (1.8 Nm) . 3. Remove adhesive backing from and apply the left-side trimplate to the swingarm. Apply pressure to the trimplate on the swingarm for one minute. 4. Remove adhesive backing from and apply an emblem to the center of the pivot cover. Apply pressure to the emblem for one minute. 5. Repeat Steps 1-4 for the right side of the swingarm. 6. Allow adhesive to cure for 24 hours before operating the vehicle. SERVICE PARTS 4 2 5 3 1 5 6 3 is01811 Figure 1. Service Parts: Swingarm Pivot Cover Kit Table 1. Service Parts: Swingarm Pivot Cover Kit Part Number Description (Quantity) Item Not Sold Separately Right-side trimplate and adhe- sive 1 Not Sold Separately Left-side trimplate and adhesive 2 Not Sold Separately Adhesive emblem (2) 3 Not Sold Separately Left-side pivot cover 4 3231B Set screw (2) 5 Not Sold Separately

Incoming search terms:

HARLEY DAVIDSON 80-SPOKE REAR WHEEL KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 31-03-2011

download
Additional Parts Required This kit includes the custom wheel only. Proper installation of this kit requires the separate purchase of the following parts which are available at a Harley-Davidson dealer: •Wheel Bearing Remover and Installer (HD-44060) •Wheel Installation Kit (See Service Parts Tables for part number) The following Harley-Davidson Genuine Motor Accessories are recommended for proper maintenance and cleaning: •Harley® Bright™ Chrome Cleaner (94683-99) •Harley® Glaze™ Polish and Sealant (99701-84) •Harley®Wheel and Spoke Brush (43078-99) •Harley-Davidson®Wheel and Tire Cleaner (94658-98) The rider’s safety depends upon the correct installation of this kit. Use the appropriate service manual procedures. If the procedure is not within your capabilities or you do not have the correct tools, have a Harley-Davidson dealer perform the installation. Improper installation of this kit could result in death or serious injury. (00333a) NOTE This instruction sheet references Service Manual information. A Service Manual for your model motorcycle is required for this installation and is available from a Harley-Davidson Dealer. Kit Contents See the Service Parts section for kit contents. INSTALLATION 1. Remove existing rear wheel assembly. Save axle, axle nut, brake disc and wheel spacers for kit installation. NOTE Remove the rear brake caliper before removing the wheel. Do not re-use sprocket mounting screws. Re-using sprocket mounting screws can result in torque loss and damage to the sprocket and/or belt assembly. (00480b) 2. Install the tube and tire on wheel. Refer to REAR WHEEL in the Service manual. Do not re-use brake disc screws. Re-using disc screws can result in torque loss and damage to rotor and/or brake assembly. (00319b) NOTES Install the primary bearing first using appropriate Service Manual and WHEEL BEARING REMOVER/INSTALLER. 3. Assemble wheel installation kit components and brake disc(s) to wheel, using the appropriate service parts table. Refer to REAR WHEEL in Service Manual. 4. Install rear wheel (1), stock axle and stock axle nut. Refer to REAR WHEEL in Service Manual

Incoming search terms:

HARLEY DAVIDSON FRONT AGITATOR WHEELS INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 06-03-2011

download
Recommended Additional Parts The following Harley-Davidson Genuine Motor Accessories are recommended for proper maintenance and cleaning: •Harley® Bright™ Chrome Cleaner (94683-99) •Harley® Glaze™ Polish and Sealant (99701-84) •Harley®Wheel and Spoke Brush (43078-99) •Harley-Davidson®Wheel and Tire Cleaner (94658-98) Kit Contents See Figure 1 and the Service Parts Tables. INSTALLATION 1. Remove existing front wheel assembly. Save axle, axle nut, brake disc and wheel spacers for kit installation. See the service manual. Do not re-use brake disc/rotor screws. Re-using these screws can result in torque loss and damage to brake components. (00319c) 2. See Figure 1. Install valve stem assembly (D) on wheel. See the service manual. 3. Assemble wheel installation kit components and brake disc(s) to wheel, using the appropriate service parts table. See the service manual. 4. Install primary bearing with a Wheel Bearing Remover and Installer. See the service manual. The left side of the wheel has DOT cast in the wheel to indicate the primary side of the wheel. 5. Install wheel spacers (previously removed). 6. Install front wheel (1) and stock axle. See the service manual. MAINTENANCE AND CLEANING Chrome parts must be maintained regularly so they keep their original shine and luster. 1. Clean heavily-soiled wheel surfaces using Harley-Davidson Wheel and Tire Cleaner, applied with Harley Wheel and Spoke Brush. 2. Thoroughly clean chrome with a good quality chrome cleaner, such as Harley Bright Chrome Cleaner. 3. After cleaning and polishing, seal the finish with a good quality sealer, such as Harley Glaze Polish and Sealant

Harley Davidson 1990 and later HSR Choke Cable Installation Manual

0

Filed Under (Harley Davidson) by admin on 28-02-2012

download
The majority of HSR42/45 installations use the Harley cable. Installation is simple when the installation instructions are followed, step by step. Those steps are: • Remove the stock Harley choke cable assembly. • Remove the spring and plunger from the stock cable. • Remove the Mikuni “Starter Nut” from the HSR. • Remove the Mikuni spring and plunger from the HSR. • Install the Mikuni spring and plunger on the Harley choke cable. • Install the Harley choke cable with the fitted Mikuni spring and plunger into the HSR carburetor. • DO NOT use the Mikuni Starter Nut; discard it. • DO NOT use the Harley spring or plunger; discard them. Note: If you do not have installation instructions, you may download them from the www.mikuni.com website in the “manuals” section. If the Mikuni Starter Nut is fitted to the Harley cable, the choke plunger is held off its seat and the choke is open all the time. If the Harley spring and plunger are used, the plunger does not seal and the choke is open all the time. The result, in both cases, is very poor fuel mileage (30 mpg or less). Another possible cause of poor mileage, rough idle and fouled spark plugs is incorrect cable routing. The stock Harley choke cable is very stiff and may not be fully seated in the metal elbow at the carburetor end of its run. This condition is easily corrected. On occasion, one of these errors may have been made by someone else at another location. The unfortunate mechanic who inherits the task of correcting the rich condition, poor idle and poor fuel mileage may have no clue as to the mismatch of parts. For this reason, we include the photos and text to help you discover if your installation is correct.

Incoming search terms:

Harley Davidson Installing The Ride Time Ultra Progressive Tour Pak LED Tail Lights

0

Filed Under (Harley Davidson) by admin on 31-10-2010

download
Remove the light bulbs from the tail light housing by depressing the tab on the bulb socket assembly and turning counter clockwise. Remove the bulb from the bulb socket. 2. Remove the lenses from the warp-around light fixture. These lens are held in place by a non-hardening black sealant. In addition, there are three plastic alignment tabs on the lens body that clip into the lens frame. To remove the lens, insert the supplied push Stick through the hole in the back of the light bulb housing and gently but firmly push the lens outward. This action places a stress on the alignment tabs. 3 . Using a flat blade screw driver, pry the lens away from the frame at the top, side, and bottom to release the lens alignment tabs. Go back to step 2, and use the plastic tube to push the lens outward. It may be necessary to repeat the prying process and pushing process several times to remove the lens. Note: Some users have found it useful to heat the lens area with a hair dryer to soften the adhesive. Included in this kit are: Left and Right LED modules, 1 RTQC Quick Connect Accessory Cable , 2 RTV application sticks, 1 push stick, Approximately 3 inches of shrink tube, and 1 copy of instructions. Required for installation, but not included are: A tube of Permatex RTV (available at Wal-Mart), 1/8 inch drill bit, a drill, small flat blade screwdriver, other hand tools. Window/ body sealer if required to reseat lenses can be obtained at your local glass shop. Tour Pak, Harley Davidson, Electraglide, Raod King, and Ultraglide are registered trade marks of Harley David- son. Harley Davidson does not make or endorse the use of these lights. 4. When the lens begins to emerge from the frame, grasp it at the top and bottom and pull the lens from the housing using a up and down motion. Set the lens aside . Avoid having the sealant contact other surfaces. In most cases, the lens can be reinstalled without adding additional sealant . Note: Do not use RTV to reset the lens. If sealant is needed obtain a non-hardening body/windshield sealant from your local glass shop. 6. When you are comfortable with the location of the circuit board, drill a 1/8 inch hole in the back of the light housing. This hole will be used to bring the turn signal wire from the LED module into the Tour Pak. 7. Using the supplied stick, spread a thin layer of Permatex clear RTV silicone seal along the area where the circuit board will be located. Apply a similar layer to the top of the light housing. Route the turn signal wire through the 1/8″ hole and position the circuit board in the housing. Allow the RTV to cure. 5. Test fit the LED light board in the light housing.

Incoming search terms: