beta rev 3 condenser

You search Auto repair manual PDF beta rev 3 condenser, if there are search results will appear below. If search results do not exist, please search by others keyword.



  beta rev 3 condenser Direct Download speed 5282 Kb/s

  beta rev 3 condenser Full Version speed 6162 Kb/s



BILLET ALUMINUM DISTRIBUTOR WITH ELECTRONIC ADVANCE AND ADJUSTABLE REV LIMITER FOR 1936-69 HARLEY BIG TWIN MOTORCYCLES INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 25-11-2010

download
ELECTRICAL SYSTEM A 12 volt electrical system is required. Check that the charging system is working properly and not producing over 16 volts. DISTRIBUTOR CLAMP A 1966-69 style distributor clamp (original or aftermarket) is required. MODULE This distributor uses an Accel Single/Dual Fire Ignition module part number 35496. See the enclosed form “Instruction Sheet Single/Dual Fire” for instructions on wiring, adjusting the rev limiter and selecting an advance curve. COIL(S) A coil(s) with a total primary resistance of 2 to 4 ohms is recommended. INSTALLATION Step 1 Turn the ignition switch to the off position. Rotate the engine until it is on the compression stroke for the front cylinder. Continue to rotate the engine until the TDC mark is visible through the timing hole. (see repair manual if necessary). Step 2 Remove the existing distributor if still in the engine. Step 3 Remove the two button head screws from the top of the Mallory distributor. Pull the top cover off the distributor. Remove the two hex standoffs and pull the module and upper housing off the distributor base assembly. Adjust the switches on the module for the desired advance curve and rev limit. FORM 1627 07/08 Step 4 Install the distributor base assembly in the engine with the screw holes and shutter wheel positioned as shown in Figures 1 and 2. It may be necessary to pull the distributor out, turn the shaft and reinstall to get the shutter wheel at the approximate angle shown. The slots should be at about the11 o’clock and 7 o’clock positions. The screw holes should be at the 9 o’clock and 3 o’clock positions. Step 5 Install the distributor clamp and tighten the clamp bolt lightly so the distributor can still be rotated. Step 6 Set the upper housing on the base assembly as shown in figure 3. (The upper housing will only install one way because of the locating screw) Rotate the base assembly slightly if necessary so that the slot in the shutter wheel lines up with the slot in the upper housing. Tighten the distributor clamp

DUCATI SUPERBIKE 848 Owner's manual and maintenance manual

0

Filed Under (Ducati) by admin on 14-12-2010

download
Position of the motorcycle controls (fig. 3) 1) Instrument panel. 2) Key-operated ignition switch and steering lock. 3) Left-hand handlebar switch. 4) Clutch lever. 5) Rear brake pedal. 6) Right-hand handlebar switch. 7) Throttle twistgrip. 8) Front brake lever. 9) Gearchange pedal. 1 4 3 2 9 8 5 7 6 fig. 3 11 E Instrument panel (fig. 4) 1) LCD (see page13). 2) Tachometer (rpm). Indicates engine revs per minute. 3) Neutral (N) indicator ( green ). Illuminates when the gearbox is in neutral. 4) Fuel warning light ( yellow ). Illuminates when there are about 3 litres of fuel left in the tank. 5) Turn signal indicator light ( green ). Illuminates and flashes when the turn signal is in operation. 6) Engine oil pressure warning light ( red ). Illuminates when engine oil pressure is too low. This light should illuminate when the ignition is switched to ON and should go out a few seconds after the engine starts. It may come on briefly if the engine is very hot, but should goout again as engine speed increases. Important If this light (6) stays on, stop the engine to avoid serious damage. 7) High beam warning light ( blue ). Illuminates when the high beam headlight is on. 8) “Engine diagnostics light” ( amber ). The engine ECU illuminates this light steadily to indicate the presence of errors leading to engine lock. 9) “Motorcycle diagnostics” light . Illuminates when the motorcycle diagnostics detects a problem. 10) Rev limiter indicator lights . Indicator light 10A: illuminates steadily at 800rpm before intervention of the rev limiter. Indicator lights 10A + 10B: illuminate steadily 400rpm before intervention of the rev limiter. Indicator lights 10A + 10B + 10C: start flashing when the rev limiter is reached. 2 1 5 9 8 6 3 4 5 7 10B 10C 10A fig. 4 12 E 11) 2-position switch A and B . Switch used for displaying and setting instrument panel parameters. It has two positions, A “▲” and B “▼”. 12) High beam headlight flasher switch (fig. 5). The high beam headlight flasher switch is also used for theLAP and USB data aquisition functions.

DUCATI MONSTER 696 Owner's manual and maintenance manual

0

Filed Under (Ducati) by admin on 14-12-2010

download
instrument panel (fig. 4) 1) LCD (see page13). 2) Tachometer (rpm). Indicates engine revs per minute. 3) Neutral (N) indicator ( green ). Illuminates when the gearbox is in neutral. 4) Fuel warning light ( yellow ). Illuminates when there are approximately 3litres of fuel left in the tank. 5) Turn signal indicator light ( green ). Illuminates and flashes when the turn signal is in operation. 6) Engine oil pressure warning light ( red ). Illuminates when engine oil pressure is too low. This light should illuminate when the ignition is switched to ON and should go out a few seconds after the engine starts. Important If this light (6) stays on, stop the engine to avoid serious damage. 7) High beam warning light ( blue ). Illuminates when the high beam headlight is on. 8) “EOBD engine diagnostics light” ( amber ). The engine ECU iluminates this light steadily to indicate the presence of errors leading to engine lock. 9) OVER REV indicator lights . Illuminates steadily at 800 rpm before intervention of the revlimiter. Starts flashing when the rev limiter is reached. 5 8 2 4 9 3 1 6 7 fig. 4 12 E 10) 2-position switch A and B . Switch used for displaying and setting instrument panel parameters. It has two positions, A “▲” and B “▼”. 11) High beam headlight flasher switch (fig. 5). The high beam headlight flasher switch is also used for the LAP and USB data aquisition functions. 11 A 10 B fig. 5 13 E LCD – Main functions Warning Any adjustments to the instrument panel must only be carried out when the motorcycle is stationary. Never operate the instrument panel controls while riding the motorcycle. 1) Speedometer . Indicates road speed. 2) Odometer . Shows total distance travelled. 3) Trip meter . Indicates the distance travelled since last reset. 4) Fuel reserve trip counter . Shows distance travelled on reserve fuel. 5) Clock . 6) Air temperature indicator . 7) Lap time . 8) Rev counter (RPM) . 9) Lap time . 8 11 13 12 14 10 4 5 9 6 2 3 1 7 fig. 6 14 E 10) Service indicator (fig. 6). The indicator illuminates to signal when a service is due. The service indiactor will remain on the display until the system is reset by the Ducati Service Centre who carry outthe service. 11) LAP function (fig. 6). Indicates that the LAP has been activated. 12) DDA function (fig. 6). Indicates that the Ducati Data Analyzer (DDA) has been activated. Important The instrument panel incorporates diagnostic functions for the electronic injection/ignition system. The relative menus are for the use of trained personnel only. If you accidentally access this function, turn the key to OFF and have the motorcycle checked at an authorised Ducati Service Centre. 13) Oil temperature indicator (fig. 6). Important Stop riding if the temperature reaches the maximum value, otherwise the engine might be damaged. 14) Ducati Traction Control (DTC) (fig. 6). Indicates activation of the DTC control unit (if present). 15 E LCD – How to set/display parameters At key-on (key turned from OFF to ON ) the instrument panelactivates all the digits of the LCD for 1second and switches on the indicator lights in sequence.

Incoming search terms:

2004 Vengeance MOTORCYCLE OWNERS MANUAL

0

Filed Under (Vengeance) by admin on 21-11-2010

download
Vengeance Warrior • Vengeance Raider • Vengeance Vertebreaker • Vengeance Striker • Vengeance Vendetta • Vengeance Vindicator Shifting Gears Starting off and changing gears requires coordination of the clutch and throttle and gearshift lever. If you don’t do things right, the amount of control you have over the bike is lessened. To start off, pull in the clutch, shift into first gear, roll on the throttle a little, and ease out the clutch. You will become familiar with the friction zone (that’s where the clutch begins to take hold and move the bike), and you add a bit more throttle. You don’t want to stall the engine, nor do you want to over-rev it. There’s a sweet spot in there; find it. Shift while traveling in a straight line. Shifting in a curve is not good practice, and something to be avoided. Become familiar with the sound of your engine, so you can tell when you should shift without looking at your instruments. When you downshift to a lower gear, you should (in one swift, smooth movement) be able to squeeze the clutch, rev the engine a little to let it catch the lower gear smoothly, and shift down. When you come to a stop in traffic, leave the bike in first gear with the clutch disengaged (just in case you want to accelerate out of there in a hurry). Who knows what may be coming up behind you. Braking Don’t ever forget: The front brake on your motorcycle can supply as much as 70 percent or more of your stopping power. The single most important thing you can learn about braking is to use that front brake every single time you want to slow down. Always apply both the front and the rear brakes at the same time. If necessary, apply them hard, but not so hard that you lock up either wheel. A locked wheel, as well as causing the bike to skid, results in downright inefficient braking. Turning When you are riding along the road, you lean a motorcycle into a turn. Learning to lean is an essential part of riding a motorcycle. It is a normal function of the bike when you are changing its path of travel – and quite different from turning the steering wheel of your car. To get the motorcycle to lean in a normal turn, press the handlebar in the direction of the turn and maintain slight pressure on that handlebar to take you smoothly through that particular turn. In other words: press right to go right; press left to go left. Your instincts to keep the motorcycle on a smooth path while keeping it from falling over usually take care of this without you even noticing it. (Demonstrate to yourself how a motorcycle moves by pressing a handlebar slightly while traveling in a straight line. The motorcycle will move in the direction of the handlebar you pushed.)

Vengeance Motorcycle Specification And Owner's Manual

0

Filed Under (Vengeance) by admin on 20-11-2010

download
Vengeance Maxis • Vengeance Raven • Vengeance Banshee • Vengeance Whiplash • Hotrod Drifter • Hotrod CalChop • Hotrod Teacher • Hotrod Bone Shifting Gears Starting off and changing gears requires coordination of the clutch and throttle and gearshift lever. If you don’t do things right, the amount of control you have over the bike is lessened. To start off, pull in the clutch, shift into first gear, roll on the throttle a little, and ease out the clutch. You will become familiar with the friction zone (that’s where the clutch begins to take hold and move the bike), and you add a bit more throttle. You don’t want to stall the engine, nor do you want to over-rev it. There’s a sweet spot in there; find it. Shift while traveling in a straight line. Shifting in a curve is not good practice, and something to be avoided. Become familiar with the sound of your engine, so you can tell when you should shift without looking at your instruments. When you downshift to a lower gear, you should (in one swift, smooth movement) be able to squeeze the clutch, rev the engine a little to let it catch the lower gear smoothly, and shift down. When you come to a stop in traffic, leave the bike in first gear with the clutch disengaged (just in case you want to accelerate out of there in a hurry). Who knows what may be coming up behind you. Braking Don’t ever forget: The front brake on your motorcycle can supply as much as 70 percent or more of your stopping power. The single most important thing you can learn about braking is to use that front brake every single time you want to slow down. Turning When you are riding along the road, you lean a motorcycle into a turn. Learning to lean is an essential part of riding a motorcycle. It is a normal function of the bike when you are changing its path of travel – and quite different from turning the steering wheel of your car. To get the motorcycle to lean in a normal turn, press the handlebar in the direction of the turn and maintain slight pressure on that handlebar to take you smoothly through that particular turn. In other words: press right to go right; press left to go left. Your instincts to keep the motorcycle on a smooth path while keeping it from falling over usually take care of this without you even noticing it. (Demonstrate to yourself how a motorcycle moves by pressing a handlebar slightly while traveling in a straight line. The motorcycle will move in the direction of the handlebar you pushed.) • Slow down before you enter the turn; look as far ahead as possible through the turn. • Keep your feet on the pegs, and grip the gas tank with your knees. • Lean with the motorcycle; don’t try to sit perpendicular to the road while the motorcycle is leaning over. • Keep an even throttle through the turn, or even accelerate a little bit. Checking the Bike before the Ride It’s not fun to have things go wrong on a motorcycle, but if you spend a minute before you go off on a ride, you can increase the chances that nothing will.

Incoming search terms:

MOTO GUZZI Quota 1100 ES Specifications And Owner's Manual

0

Filed Under (Moto Guzzi) by admin on 25-11-2010

download
Engine 4-stroke, twin cylinder Cylinder configuration: 90° V-twin Bore: 9 2 mm Stroke: 80 mm Capacity: 1064 cc Compression ratio: 9.5:1 Max. torque: Nm 85 (kgm 8.7) at 3,800 rpm Max. power: Kw 51 (CV 70) a 6,400 rev/min Timing system With rods and rockers and 2 valves per cylinder. One camshaft in the crankcase driven by duplex chain with automatic chain tensioner. Feed system Indirect electronic injection, timed sequential MAGNETI MARELLI IAW 15M “Alfa-N” system, single throttlebody, Weber IW031 injectors, electric pump with pressure regulator, digital control of optimized injection times. Lubrication Pressure fed by gear pump. Wire mesh and cartridge filters on oil sump. Normal lubrication pressure 3.8÷4.2 kg/cm2 (pressure valve on oil sump). Low oil pressure sensor (electrical) on crankcase. Generator / Alternator On front of crankshaft. Output power: 350W at 5000 rev./min. (14V – 25A). Ignition “MAGNETI MARELLI” Inductive discharge digital electronics. Spark plugs: NGK BPR 6 ES. Spark plug gap: 0.7 mm 2 ignition coils Starter Electric starter motor 12V-1.2 Kw with electromagnetic ratchet control. Ring gear on the flywheel. START « » push-button on right handlebar. Transmission Clutch Dry, twin driven plates. Located on engine flywheel. Clutch lever on left handlebar. Primary drive With helical gears, 1:1.3529 (Z=17/23). Gearbox 5-speed, front engaging, constant mesh. Incorporated Cush drive Control pedal on left side of machine. Gear ratios: 1st 1:2 (Z=14/28) 2nd 1:1.3158 (Z=19/25) 3rd 1:1 (Z=23/23) 4th 1:0.8462 (Z=26/22) 5th 1:0.7308 (Z=26/19) Final drive Cardan shaft with gears Ratio: 1:4.125 (Z=8/33) Overall gear ratios (engine-wheel) 1st gear = 1: 11.1618 2nd gear = 1: 7.3433 3rd gear = 1: 5.5809 4th gear = 1: 4.7223 5th gear = 1: 4.0783 Frame Double steel rectangular bar with double cradle

2003 COBRA PW3 Owners / Service Manual

0

Filed Under (Cobra) by admin on 10-11-2010

download
Starting Procedure Before starting the machine inspect the following: • Fill the 2-stroke injector oil reservoir with Cobra’s specially formulated Cobra Venom 2-cycle Race Oil . • Insure that the fuel tank contains an adequate volume of fuel to complete the distance required. ( Sunoco MO2X or 93 octane pump gas). • Check for proper tire pressure in both tires. • Observe the chain tension and adjust if necessary. • Observe the coolant level and fill if necessary. • Verify that the chain rollers do not have improper wear. • Inspect the frame for; o Cracks in the metal. o Cracking paint which might indicate overly stressed material. • Verify that the handlebars are tight. • Check the throttle for; o Smooth operation and sound closing. o Frayed strands of the cable inside the throttle housing. • Check for loose bolts and nuts, and re-torque as necessary. • Verify that the air filter is clean and properly saturated with oil. • Turn the fuel on by rotating the fuel petcock knob to the vertically downward position (reserve position is horizontally forward). CAUTION: For best results from your Cobra Motorcycle use only the recommended fuels. Testing has shown that most ‘race’ fuels actually degrade performance. When your pre-ride inspection is complete the bike may be started. For a cold engine follow this procedure. 1. Place the motorcycle on a stand of sufficient strength that positions the motorcycle in a level upright position with the rear wheel off the ground. 2. On the carburetor, flip the black choke knob upward from the right side of the bike. 3. Kick start the engine by kicking the lever forward. 4. Rev the engine in short spurts, turning the throttle no more than 1/4 open until the engine will run without the choke. 5. Verify a functional engine shut-off switch by shutting off the engine. 6. Restart the engine and proceed with riding when the engine is sufficiently warm (i.e. the side of the cylinder is warm to touch). CAUTION: Never rev an engine full throttle when it’s cold or slightly warmed up. Cobra recommends that you tell your child to take it easy the first couple of minutes in practice until the engine comes up to full operating temperature. Make sure your engine is properly warmed up before racing.

KTM 250/300/380 SX,MXC,EXC ENGINE REPAIR MANUAL

0

Filed Under (KTM) by admin on 19-11-2010

download
Carburetor adjustment Basic information on the original carburetor setting The original carburetor setting was adapted for an altitude of approx. 500 meters (1600 ft.) above sea level, and the ambient temperature of approx. 20°C (68°F), mainly for off-road use and central European premium-grade fuel (ROZ 95 MOZ). Mixing ratio 2-stroke motor oil : super fuel 1:40 – 1:60. Basic information on a change of the carburetor setting Always start out from the original carburetor setting. Essential requirements are a clean air filter system, air-tight exhaust system and an intact carburetor. Experience has shown that adjusting the main jet, the idling jet and the jet needle is sufficient and that changes of other parts of the carburetor will not greatly affect engine performance. Checking the setting of the TVC system The function of the TVC system is checked with the engine running. This test checks the start of advance and the end of advance. -For this, remove the left control cover. -Connect a rev counter (either to the ignition cable or to the blue/white cable in the electronics box, depending on the rev counter design). -Start engine, accelerate gently and observe when the TVC system starts to advance (tooth segment creeps upwards) Bleeding of the hydraulic clutch -Take off cover together with rubber bellows. -At the slave cylinder of the clutch, remove the bleeder nipple 2 . It its place, mount the bleeder syringe 3 which is filled with SAE 10 hydraulic oil

Harley-Davidson Electronic Ignition Module Installation instructions

0

Filed Under (Harley Davidson) by admin on 23-04-2012

download
Step 1: Switch main dashboard switch to “off” position (Ignition& light switch) Step 2: Disconnect negative (ground) cable from the Battery Step 3: Remove the Condenser and Breaker points from the circuit breaker timing base. Step 4: Disconnect advance/ retard cable from timing base Step 5: Remove timing base from timer shaft and housing (see your manual for instructions) Step 6: Remove circuit breaker wire stud or circuit breaker to coil wire assembly from timing base Step 7: Remove circuit breaker wire from Ignition coil, and mark terminal on coil with piece of tape. Step 8: Install the Electronic Ignition Module on the timing base. Mount this short black wire to one on the timer base screws by keeping some slack in this wire so the timing base can turn free. Solder the flag terminal to this short black wire and mount it under the timer to motor bolt. This way of mounting provides a much better grounding. Do NOT use the screws (number 1 or 2 screws from picture below) from the timing base!!!! Step 9: Now three wires pass this hole via the rubber grommet. Figure 1 Figure 2 Step 10: Reinstall the timer base on the timer shaft housing, and keep some slack in the wires before protruding the hole in the timer shaft housing, and secure with ground spring and cover retainer. Reconnect the advance/retard cable to the timer base. Step 11: Route the two long wires to the ignition coil. Check in the HD service manual for a proper route to the ignition coil. (Keep away from hot surfaces like exhaust systems). Cut the wires to the exact length necessary for mounting. Step 12: Determine the exact length of the wire loom. Keep in mind that one end of the loom enters the timer shaft housing by 1cm. Cut the loom to the proper length. Step 13: Insert both wires in the loom. Strip both wire ends and solder the two flag terminals on the wires. Step 14: Connect the red wire to the ignition coil, on the terminal where the 6 or 12 volt is supplied to. This terminal has at minimum one wire connected which runs to the main switch. Step 15: Connect the black wire to the ignition coil on the terminal which is empty, and has piece of tape on it. (Old place where the circuit breaker wire was connected to) Step 16: Install the trigger rotor on the timer shaft cam, and tighten the hex screw by using the hex key tool. Do not over tighten the screw! Step 17: Check for clearance between trigger rotor and Electronic Ignition Module. Appropriate clearance is between 0,5mm and 1,5mm . Minor adjustments can be made by unlocking the two screws and slightly shift/move the Electronic Ignition Module. Check if the rotor moves free. Timing instructions: Remove the spark plugs from the engine, but keep them connected to the spark coil cables and engine ground. This enables normal operation of the spark, and prevents unwanted engine firing on compression stroke. See service manual or handbook for timing instructions of your model Step 18: Reconnect the negative (ground) cable to the battery. Step 19: Switch main power to “on” position. The red light in the Electronic Ignition Module might already light up. If not, turn the kick starter slowly. The red light is on while charging (closed points)the Ignition coil, facing solid metal of the trigger rotor. The light goes off (open points) when the end of the solid surface of the trigger rotor passes the centre of the Electronic Ignition Module. At that point a spark is generated by the coil

Incoming search terms:

DYNA III ELECTRONIC IGNITION INSTALLATION INSTRUCTIONS

0

Filed Under (Tips and Review) by admin on 27-10-2010

download
1)Fasten the clamp to the electronic module using the 4-4O x 5/16 screws and lockouts provided. The damp and nuts go on the inside of the case. 2)Remove the fuel tank. Attach the module to the frame in the location selected. Cut off excess clamp material. 3)Remove an engine case or valve cover bolt and fasten the ground lug (black wire) securely to the engine. DO NOT ATTACH TO FRAME. 4])Locate the two ignition coils (they are positioned behind the left side cover on some models). There is a white wire going to the positive side of one coil that carries the switched 12 volts. A short blue/black wire then connects that point to the positive side of the other coil. Connect the separate red wire included with the kit to the spare spade terminal that is available on the positive terminal of the second coil. 5)Plug the red wire coming from the electronic module into the red wire installed in Step 4. 6)Remove the cap from the contact breaker housing. Remove the alternator cover, timing mark inspection plug, and spark plugs. 7)Remove the two screws and clips holding the points plate to the housing. Remove the screws holding the condensers to the housing. Disconnect the red and green wires where they plug into the wire harness (or coils), and remove the entire points/plate/condenser assembly. 8)Make sure the top of the housing is clean. Place the DYNA III sensor plate on the housing and orient it so that the wires exit to the rear. Place one of the original wire grommets on the front end of the plate and secure it with the screw and clip previously removed. Route the sensor cable wires through the other grommet (2 wires in the largest hole) and secure with the other screw and clip. Before tightening the plate screws, make sure the plate does not obstruct the cap screw holes. 9)Using a hex wrench in the alternator bolt, rotate the engine forward until the right hand cylinder is at top dead center on the compression stroke (D mark aligned with index mark on engine case). 10) Make sure the points cam is free of dirt and grease, and slip the DYNA III rotor over the cam Push the rotor down until it’s flange is in contact with the top of the cam. Orient the rotor so that the mark on top aligns with the line on the left (right cylinder) sensor. While pushing down on the rotor, tighten the set screws using the alien wrench supplied with the kit. 11)Rotate the engine by hand and check run-out (wobble) of rotor by watching the rotor/sensor gap. If the rotor is installed correctly, there should be no more than . 005 run-out, and it should not come in contact with either sensor. As a final check, turn the engine with the electric starter and observe the run-out. 12)Connect the three sensor cable plugs to the module receptacles, matching the red, white, and black wires. 13)Plug the remaining red and green wires onto the spade terminals where the original points connected, matching the colors