bike rack manufacturers china mail

You search Auto repair manual PDF bike rack manufacturers china mail, if there are search results will appear below. If search results do not exist, please search by others keyword.





HARLEY DAVIDSON PREMIUM TOUR-PAK LUGGAGE RACK KIT INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 01-02-2011

download
INSTALLATION Template Positioning (Rack Installation WITH SPOILER only) The location of the luggage rack has a direct relationship to the location of the Tour-Pak® Spoiler. The template (7) included in this kit will locate the luggage rack in the correct position for the current or future installation of a Tour-Pak Spoiler. NOTE A template is not required if installing rack without spoiler. 1. If a spoiler is already installed, or if the installation of a Tour-Pak-mounted spoiler may be desired in the future, cut the template along the appropriate line. 2. Carefully place the trimmed template on top of the Tour- Pak, aligning the edges of the template with the top surface of the Tour-Pak lid. Tape the template to the lid in the desired location. The template will help to properly locate the rack so that a spoiler may be added in the future. Rack Installation on Tour-Pak 1. ALL installations: Open the lid, and remove all loose contents from the Tour-Pak. 2. See Figure 1. Slip the mounting pads (2) onto each of the mounting bosses (B) of the luggage rack (1). NOTES Kit 53665-87: Position rack with wide upright toward rear of vehicle. Kit 91793-85: Position rack with upright toward rear of vehicle. Carefully center the rack from left to right, and position the rack squarely on the lid for best appearance. Do not mount the rack too far forward to avoid contact with the backrest pad. 3. Position the rack on the Tour-Pak lid in the desired loca- tion. 4. Carefully raise the rack, and place masking tape (A) on the Tour-Pak lid where the four mounting bosses contact the cover. 5. Lower the rack onto the tape in the location chosen in Step 3. Using a soft lead pencil on the masking tape strips, trace a circle around each mounting boss. Remove the rack, and use a ruler to mark the exact center position of each mounting boss on the tape. 6. Drill four 1/16 inch (1.5 mm) diameter pilot holes through the masking tape and Tour-Pak lid at each mounting boss center position. Use a 9/32 inch (7 mm) diameter bit to drill the finish holes. 7. Remove the masking tape

HARLEY DAVIDSON TOUR-PAK RACK LIGHT KIT INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 06-02-2011

download
INSTALLATION 1. Remove all contents from Tour-Pak®. 2. For easier installation, remove Tour-Pak rack, if installed, by removing cap screw, washers and mounting pads. 3. See Figure 1. Remove rubber plug from bottom rear rail on left side of rack. 4. See Figure 2. Use line wire feeder in kit to thread through left rear rack foot and out through the back opening of rail. 5. Attach light harness wires to line wire feeder loop. 6. Carefully pull line wire feeder and light harness wires through rack mounting foot. 7. See Figure 5 and Table 1. Apply foam pads (5) to top surface of light. 8. Secure light (1) to rack with socket head screws (4) and washers (6). 1 is05242 1. Plug Figure 1. Left Side Rack Plug 1 is05244 1. Line wire feeder Figure 2. Thread Wires Through Rack 9. Position rack/light assembly to Tour-Pak lid and route wires through lid, washer and hollow mounting bolt. 10. Attach rack/light assembly to Tour-Pak using instructions and hardware provided with rack except for use of hollow bolt from Step 9. 11. Remove Tour-Pak liner. 12. Thread wires through black vinyl conduit. 13. Ultra Classic models: Follow Steps 14 through 2114. Locate and disconnect three pin AMP connector for Tour- Pak lights. 15. See Figure 3. Attach the Y-harness (2) to the three pin male connector (1) of Tour-Pak harness. 16. Route light wires from back of Tour-Pak along left side to front. Secure conduit with adhesive clips provided in kit. 17. Trim length of light wires and conduit to reach Y-harness. 18. Refer to the Service Manual electrical appendix to install terminal pins (8) to rack light wires and install terminals to three pin housing (7) as follows: a. #1 cavity = blue lead b. #2 cavity = red with yellow lead c. #3 cavity = black lead 19. Connect rack light to remaining Y-harness connector. 20. Replace Tour-Pak liner. 21. Check operation of Tour-Pak tail and stop light functions before operating motorcycle. 22. Classic models: See Figure 4. If necessary, drill hole in lower left bottom of Tour-Pak and install grommet. Route rack light wires through grommet. 23. Refer to the Service Manual electrical appendix to install terminal receptacle (8) to rack light wires and install terminals to three pin receptacle housing (7) as follows: a. #1 cavity = blue lead b. #2 cavity = red with yellow lead c. #3 cavity = black lead NOTE To prevent corrosion, fill the cavities of the connectors with dielectric grease (included in kit) prior to making connections. As an additional precaution against moisture seepage into the Tour-Pak, apply silicone sealant (not included in kit) to the entrance of the light harness wire tunnel. See figure 2 for location reference. 24. Connect rack light to male connector of two connector wire harness (12) and connect to accessory connector under seat. 25. Replace Tour-Pak liner. 26. Check operation of Tour-Pak tail and stop light functions before operating motorcycle

Incoming search terms:

HARLEY DAVIDSON CONTOURED TOUR-PAK LUGGAGE RACK KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 05-04-2011

download
INSTALLATION NOTE The location of the Tour-Pak spoiler has a direct relationship to the location of Tour-Pak mounted luggage rack. The spoiler template will locate the Tour-Pak spoiler in the correct position for the luggage rack so that the spoiler may be added in the future. It is recommended that the spoiler be installed first. See Figure 1. 1. Identify if the installation of a Tour-Pak mounted spoiler is desired in the future. Use the template if the spoiler will be installed. Cut the template along the appropriate line. Carefully place template on top of Tour-Pak lid, aligning edges of template with top surface of Tour-Pak. Tape template in desired location. 1 is 00579 1. Check clearance between rack and spoiler Figure 1. Tour-Pak Rack and Spoiler NOTE Position top rack with upright section toward rear of motorcycle. To avoid contact with the passenger backrest pad, do not mount the top rack in too far forward a position. 2. See Figure 2. Place the four mounting pads (1) onto the four mounting supports on top rack (2). Carefully center the rack on the lid and position the rack rear supports 5/8 inch to 3/4 inch (16 mm to 19 mm) in front of the emblem on the Tour-Pak lid, as shown. 1 is 00636 1.5/8 in. – 3/4 in. (16 mm – 19 mm) Figure 2. Locate Holes From Emblem 3. Use a grease pencil to temporarily mark the positions of the four mounting pads on Tour-Pak cover. NOTE Apply masking tape to the Tour-Pak cover painted surface at the four points where the top rack mounting holes will be drilled. The tape can be marked for hole location, and will help prevent the paint from being chipped during the drilling procedure. 4. Carefully remove top rack/mounting pad assembly. Place a strip of masking tape over each grease pencil mark on the Tour-Pak cover. Once again, position top rack/mounting pad assembly on Tour-Pak cover in the desired mounting location. 5. Using a soft lead pencil on the masking tape strips, trace a circle around each mounting pad. Remove top rack/mounting pad assembly. Use a ruler to mark the exact center of each circle drawn on the tape strips. NOTE Remove all contents from within the Tour-Pak to avoid possible contact with the moving drill bit during the following drilling procedure. 6. Drill starter holes using a 1/16 inch drill bit. Drill the finished holes for the mounting screws using a 9/32 inch drill bit. Remove masking tape strips. 7. Apply a small amount of silicone sealant around each mounting hole on interior surface of Tour-Pak cover

Incoming search terms:

HARLEY DAVIDSON TOUR-PAK KIT INTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 07-02-2011

download
INSTALLATION 1. Remove the rubber mat from the bottom of the Tour-Pak. 2. See Figure 1 and Table 1 to determine the proper hole configuration to attach the Tour-Pak to your luggage rack. Holes will be drilled as explained in Step 3 in the hole location for your luggage rack. Table 1. Luggage Rack and Hole Configurations Hole Configura- tion Luggage Rack C (3 holes) Stock 1997 B (4 holes) Detachable luggage rack 53107-96 A (5 holes) Luggage rack 53118-97A and luggage rack 53118-98 A (5 holes) Stock 1998 and later racks A (5 holes) Detachable Tour-Pak rack 53276-04 B (4 holes) Solo detachable Tour-Pak rack 53655-04 B (4 holes) Detachable Tour-Pak rack 53066-00B B (4 holes) Solo detachable Tour-Pak rack 53559-04A A (5 holes) Solo detachable Tour-Pak rack 53260-02 -J03631 1 of 3 B 1 A C 2 2 2 is00163 1. Front of motorcycle 2. Bottom view of Tour-Pak interior (rubber mat removed) Figure 1. Hole configurations for Tour-Pak attachment NOTE Drilling holes in Tour-Pak without wood underneath each hole site may result in the leather becoming damaged during the drilling process. 3. Place blocks of wood underneath the Tour-Pak where the holes will be drilled to prevent damage to the leather while drilling. Use the pre-drilled holes in the metal base as a guide and carefully drill the holes through the leather in the proper location using a 11/32 inch drill bit. 4. See Figure 2. For detachable luggage racks (53107- 96, 53066-00B and 53276-04): Install black cover tube to the front bar (1) of the luggage rack, as shown. This tube is used to provide a cleaner look. The black cover tube is not for use with other luggage racks. 5. Attach Tour-Pak to rack using the mounting screws provided in the Luggage Rack kit. Put bolt through from inside of Tour-Pak. Tighten screws to specifications found in the Luggage Rack kit. 6. Place the black rubber mat on the bottom of the Tour-Pak. 7. If luggage rack was removed, reattach to motorcycle according to kit instructions or Service Manual instructions

Incoming search terms:

Harley-Davidson The WHEELDOCK EZ-UP Center Stand Installation MANUAL

0

Filed Under (Harley Davidson) by admin on 21-03-2012

download
Unlike other center stands, the WHEELDOCK EZ UP stand requires very little effort to operate and can usually be done while still on the bike by simply pushing down on the foot lever with your left foot. Once you feel both feet of the center stand in contact with the ground, transfer your weight up off of the seat and onto the foot lever of the center stand. The stand should rotate under the bike and a bit forward lifting the bike quite easily. CAUTION: Never attempt to raise the bike with a passenger on board, as you will damage the foot lever. You can also raise the bike on the center stand by using the following traditional method: Place the bike on the side stand and step off to the side. From the left side of the bike, push the bike up to the vertical position and press down on the foot lever until both feet of the stand are in contact with the ground. Now apply weight to the foot lever while lifting up on the bike. For cleaning the rear wheel: first place a ½-inch piece of plywood under the stand and use this (beside the bike) method for placing the bike up on the plywood spacer; this will allow the wheel to rotate freely for cleaning. Do not try this while on the bike, as it will require too much foot pressure on the lever. You now have two options to get the bike off of the stand: You can simply rock the bike forward, or put the bike in gear and drive off in most cases as long as you are parked on a flat, level surface. Tips for solving common questions: If you have the correct height stand and you still have difficulty getting the bike up on the stand check the following: the bike must be in neutral, the wheel should be straight forward and not cocked, do not hold the front brake lever and make sure you have 15 lb or more air pressure in the rear suspension. These are the most common problems we encounter

Incoming search terms:

Harley-Davidson touring bikes WHEELDOCK EZ-UP Center Stand Installation Instructions

0

Filed Under (Harley Davidson) by admin on 18-04-2012

download
Unlike other center stands, the WHEELDOCK EZ UP stand requires very little effort to operate and can usually be done while still on the bike by simply pushing down on the foot lever with your left foot. Once you feel both feet of the center stand in contact with the ground, transfer your weight up off of the seat and onto the foot lever of the center stand. The stand should rotate under the bike and a bit forward lifting the bike quite easily. CAUTION: Never attempt to raise the bike with a passenger on board, as you will damage the foot lever. You can also raise the bike on the center stand by using the following traditional method: Place the bike on the side stand and step off to the side. From the left side of the bike, push the bike up to the vertical position and press down on the foot lever until both feet of the stand are in contact with the ground. Now apply weight to the foot lever while lifting up on the bike. For cleaning the rear wheel: first place a ½-inch piece of plywood under the stand and use this (beside the bike) method for placing the bike up on the plywood spacer; this will allow the wheel to rotate freely for cleaning. Do not try this while on the bike, as it will require too much foot pressure on the lever. You now have two options to get the bike off of the stand: You can simply rock the bike forward, or put the bike in gear and drive off in most cases as long as you are parked on a flat, level surface. Tips for solving common problems: If you have the correct height stand and you still have difficulty getting the bike up on the stand check the following: the bike must be in neutral, the wheel should be straight forward and not cocked, do not hold the front brake lever and make sure you have 15 lb or more air pressure in the rear suspension. These are the most common problems we encounter.

Incoming search terms:

HARLEY DAVIDSON XR1200 LUGGAGE RACK KIT REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 29-03-2011

download
Kit 53976-08 (XR1200 Passenger Upright Kit) is available for separate purchase. Contact your Harley-Davidson dealer for more information. Kit Contents See Figure 2 and Table 1. REMOVAL 1. Remove pillion and seat following the instructions in the appropriate Service Manual. 2. Remove the seat base following the instructions in the appropriate Service Manual. 3. See Figure 1. Remove the turn signal mounting screws (3) and discard. Allow the turn signal to hang by the harness until lower bracket installation. 4. Remove the rear fender support strut screws (6) and dis- card. INSTALLATION 1. See Figure 2. Install lower luggage rack mount bracket with screws (9), flat washers (10) and nuts (8). Bracket will mount around nut (Item 2 in Figure 1). Tighten to 19 ft-lbs (26 Nm) . 2. Install screws (7) and nuts (8) through the rear fender support strut and the lower luggage rack mount bracket. Tighten to 19 ft-lbs (26 Nm) . 3. Route the turn signal wire harnesses through the groove in the bracket. Install new turn signal mounting screws (11). Tighten screws to 3-5 ft-lbs (4-7 Nm) . 4. Install seat base following the instructions in the appropriate Service Manual. 5. Install upper luggage rack mount bracket (4) with original equipment seat base screws in the lower holes (A). Do not tighten at this time. 6. Install screws (3) into slotted holes in the upper luggage rack mount bracket (4) and flange nuts (6). Slide the upper bracket as far back in the slots as possible. Tighten screws (3) to 10 ft-lbs (13.5 Nm) 4 1 1 2 5 6 3 is05250 1. Lower luggage rack mount bracket screw (4) 2. Nut (2) 3. Turn signal mounting screw (4) 4. Upper luggage rack mount bracket 5. Luggage rack 6. Rear fender support strut screw (2) Figure 1. Luggage Rack Installation NOTE If installing the Passenger Upright Kit (part number 53976-08) (available separately), do not install spacers (2) and screws (3) in front holes. 7. Install luggage rack (1) aligning the holes with the holes in the upper luggage rack mount bracket. Install spacers (2) and screws (3) in holes. Tighten to 6-10 ft-lbs (8-13.5 Nm) . After installing seat, pull upward on seat to be sure it is locked in position. While riding, a loose seat can shift causing loss of control, which could result in death or serious injury. (00070b) 8. Install pillion and seat following the instructions in the appropriate Service Manual. Do not exceed luggage rack weight capacity. Too much weight can cause loss of control, which could result in death or serious injury. (00373a

Incoming search terms:

HARLEY DAVIDSON LUGGAGE RACK BAG INSTALLATION INTSRUCTIONS

0

Filed Under (Harley Davidson) by admin on 02-02-2011

download
INSTALLATION 1. Set the rack bag on top of the luggage rack with the main pocket opening facing the rear of the vehicle. 2. See Figure 2, Figure 3 and Figure 4. Determine which luggage rack is installed on the vehicle. 3. See Figure 1. Open the hook-and-loop closures in the appropriate locations for the installed luggage rack. 4. Fasten the closures around the bars of the luggage rack and pressing the hook-and-loop ends together. 5. Give the rack bag a final pull to verify the pack is securely attached. 1 2 3 4 7 5 6 is05516 1. Rear left closure 2. Rear center closure 3. Rear right closure 4. Front left closure 5. Front center closure 6. Front right closure 7. Rain cover storage Figure 1. ook-and-Loop Closure Locations 1 2 3 4 5 6 is05513 Figure 2. Premium Rack Closure Locations -J00861 1 of 2 1 3 4 6 is05514 Figure 3. Air Wing Rack Closure Locations 2 5 4 6 is05515 Figure 4. Contoured Rack Closure Locations USAGE Do not exceed luggage rack weight capacity. Too much weight can cause loss of control, which could result in death or serious injury. (00373a) •Combined load of top rack and Tour-Pak® must not exceed 25 lbs (11.3 Kg). Overloading the motorcycle will cause unstable handling and reduced braking efficiency, which could result in death or serious injury. See Figure 1. Open the hook-and-loop flap on the rain cover storage pocket (7) and wrap the tethered rain cover around the bag.

HARLEY DAVIDSON TOURING DETACHABLE TOUR-PAK RACK INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 09-02-2011

download
INSTALLATION NOTE See Figure 3. When installing Tour-Pak to Rack in the following Steps, note that holes on Rack provide two positions for mounting Tour-Pak in desired location. 1. Place Tour-Pak on support tube and open lid. NOTE See Figure 3. In the following step, the longer bolts (6) are used for 2005 and earlier (King only) and Chopped Tour-Paks while the shorter bolts (5) are used for Leather Tour-Pak and 2006 and later King Tour-Paks. 2. See Figure 3. Obtain bolt (5 or 6), two flat washers (3), concave spacer (4) and hex lock nut (2) from kit. Align rear center hole in Tour-Pak with same hole in support tube (8). Slide bolt with flat washer through Tour-Pak, through support tube, then through concave spacer (with concave side facing support tube). At bottom of support tube, install washer (3) and nylock cap nut (2). With concavity on spacer inline with the rail, hold nut and tighten bolt until snug. 3. Obtain bolts (5 or 6), two flat washers (3), concave spacer (4) and hex lock nut (2) from kit. Align top support tube (8) with detachable tour-pak rack holes (four). Slide bolts with flat washer through Tour-Pak, through support tube, through concave spacer (with concave side facing support tube) then through rack. At bottom of detachable tour-pak rack, install washer (3) and nylock cap nut (2). With concavity on spacer inline with the rail, hold nut and tighten bolt until snug. NOTE Always install the mounting bolts from inside the Tour-Pak. If the bolts are installed upside down, then the ends of the bolts can tear the molded liner and scratch objects, such as helmets, stored inside the Tour-Pak. 4. Repeat Step 3 and install hardware to the remaining three holes in Tour-Pak and mounting rack. 5. In a crosswise pattern, alternately tighten the five bolts to 96-120 in-lbs (10.8-13.5 Nm) . Be sure that concavity on each spacer is inline with the rail and has not rotated out of position. INSTALLATION-TOUR-PAK AND RACK 1. Follow the instructions included in the docking point kit and install docking points. 2. See Figure 1. While standing behind the motorcycle, place the front Tour-Pak rack notches into the front docking points (1). Make sure the notches seat fully into the front docking points. 2 1 is04025 1. Front Docking Point 2. Rear Docking Point Figure 1. Docking Point Bracket 3. See Figure 1 and Figure 2. Position the latches over the rear docking points (2). Check to be sure the latches fit into the neck of the rear docking points as shown in figure 2. This may require some gentle squeezing or spreading of the rack

The New Kawasaki ZX-6R Trading in gets easier and easier

0

Filed Under (Kawasaki) by admin on 18-02-2011

download
didn’t go to my local Kawasaki shop expecting to trade in the 2004 636 I’d been happily riding. I honestly didn’t expect there to be anything on the floor that would motivate me to bring the bike in. Some of you reading this may be able to relate to what I am saying, the day you don’t look for something is the day that you find exactly what you didn’t know you need. That was the day I decided I needed to take home the new ZX-6R. The reworking of the new ZX-6R is more than just about looking good. According to KMC the engine has been redesigned from the crankcase up for the first time in ten years. Racing technology built into the new bike is a close-ratio cassette transmission that can be removed without the needing to split the main crankcases in case you needed to make repairs or adjustments at the track. They also tell us that the fuel injection system has shorter throttle bodies with a smaller diameter bore which claim to give this new smaller sized engine more torque in the mid-range. It also comes with a GPS – Gear Position Sensor. The new ZX-6R comes stock with a slipper clutch which is one difference between the 2004 and 2007. My 2004′s rear wheel would hop if I geared down before a corner and my engine rpms were too high. The slipper clutch allows quicker downshifts. To experience the gains of a slipper clutch you don’t have to buy a 2007 Kawasaki – it was introduced to the 636 in 2005. A quick glance at the exhaust might leave the impression that the ZX-6R comes stock with stacked twin small diameter exhaust cans but if you look closely you will see it is a single oval pipe with a shotgun styled end cap. The titanium pipe has the pre-chamber and catalyser located below the engine to keep the weight on the bike low and centered and the temperature of the under seat silencer reduced. Looking at the new Kawasaki with its fairing removed, I wonder how much more it would have cost the consumer to have an exhaust system that not only works wonders but would be worth showing off? Even if some of the systems of the new 600 look better hidden by plastic the bike does have a cohesive look and every year the fit and finish of Kawasaki’s bikes seem to get better. You can look at this bike from almost any angle and nothing jumps out at you – unless you are on the right side of the bike looking at the rear brake reservoir. It seems odd to me that they would leave the rear brake reservoir exposed. Another design feature of the smooth body of the 2007 ZX-6R is the lack of tie down points for any luggage. It can be argued that this is a bike intended for Sunday morning canyon rides or track days on weekends but if you want to take the 600 out for a weekend away then there is aftermarket solution. Ventura Racks allow you go on vacation with your bike. A Ventura Rack provides you with a frame that you attach to your bike that you can secure luggage to. There is no drilling of body work and the Ventura rack I got fit onto the bike perfectly the first try. One of the things I really like about the Ventura Rack is that you can easily attach bags that you may already have or you have the option of buying the Ventura luggage system. Just give yourself time before a motorcycle trip to pack

Incoming search terms: