bikebug deluxe

You search Auto repair manual PDF bikebug deluxe, if there are search results will appear below. If search results do not exist, please search by others keyword.



  bikebug deluxe Direct Download speed 5282 Kb/s

  bikebug deluxe Full Version speed 6162 Kb/s



2008 Harley Davidson Softail Deluxe Exhaust Installation Supplement to Installation Manua

0

Filed Under (Harley Davidson) by admin on 16-02-2011

download
1. Install LH and RH passenger foot peg mount using 3/8×2-1/4″ hex head bolts, 3/8″ SAE flat washers, 3/8″ lock was and 1″ spacers between the motorcycl frame and mount. Figure 1 hers e xhaust ter) n’t Cut 6-1/4″ from end Cut 1/2″ from end Figure 2 2. Remove exhaust chrome covers from header pipes. 3. It is not necessary to remove the front cylinder’s front cover. Remove header pipes from cylinder heads. Cut pipes as shown in Figure 2. 4. Replace header pipes Cut cover 5-5/8″ from end – Shown already cut Figure 3 5. Cut top cover as shown in Figure 3. 6. Install supplied extension pipes as shown in Figure 3 using the OE e clamps. (Clamps covered by covers in picture – covers will be installed la Rotate clamps to make sure they don’t interfere with the foot peg mounts. Do tighten clamps yet. 7. Mount exhaust hanger bracket to body frame with (3) supplied vibration mounts. Figure 4. Figure 4 8. Install supplied clamps to ends of mufflers and fit over exhaust extensions. 9. Attach exhaust pipes to hanger bracket with OEM hardware (4 bolts). Apply Red Loctite to OEM bolts. Figure 4. 10. Install all chrome covers 11. Tighten all exhaust clamps. Figure 5 12. Install supplied chrome cover with clamp removed from cut OE chrome cover. Supplied cover slips over OE chrome cover. Push cover forward to prevent the body from hitting the cover. Figure 5. 13. Move OE clamp backwards and install 14. Position luggage rack as shown in figure 5. Install luggage rack with OE bolt in the Figure 6 Bracket OE Bolt Clamp Figure 7 Drill ¼” holes bracket using OE bolt and supplied 3/8″ bolt. Figure 6. 7 and drill two ¼” holes in shock tower mount. 1 rear and the supplied ¼” bolts in the front.

HARLEY DAVIDSON SOFTAIL DELUXE SEATS INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 06-03-2011

download
These kits fit 2005 and later FLSTN model motorcycles. Additional Parts Required NOTE A Service Manual for your model motorcycle is available from a Harley-Davidson Dealer. Kit Contents See Figure 3 and Table 1. INSTALLATION 1. Remove existing seat according to Owner’s Manual Instructions. Save all attaching hardware. 2. See Figure 1. Install two flange nuts (1) from kit onto the seat mounting studs. Tighten flange nuts to 5-8 ft-lbs (7- 11 Nm) . 1 is03023 1. Install flange nuts Figure 1. Flange Nut Locations NOTE See Figure 3 for Steps 3-6. 3. Remove two screws (A) and rear mounting bracket (B) from stock seat. Save all hardware. 4. Install the rear mounting bracket (B) removed in Step 3 onto the new seat using the seat bracket screws (A). Tighten screws to 19 in-lbs (2.1 Nm) . 5. Install new seat (1) on the motorcycle by inserting the tab at the front of the seat into the slot at the rear of the fuel tank. After installing seat, pull upward on seat to be sure it is locked in position. While riding, a loose seat can shift causing loss of control, which could result in death or serious injury. (00070b) 6. Fasten rear seat bracket (B) to fender nut using stock mounting screw (C). 7. See Figure 2. To install grabstrap, remove front screw and washer from rear fender support. Install grabstrap with thick washers (1), thin washers (3) and screws (4) from kit. Tighten to 21-27 ft-lbs (28-37 Nm)

BUSHTEC GL1800 STANDARD & DELUXE VERTICAL RECEIVER HITCH SYSTEM Trailer Hitch Installation Instructions

0

Filed Under (Honda) by admin on 24-11-2011

download
Place the motorcycle on its centerstand on level ground. Remove the four bolts in the seat handles with a 6mm Allen head socket and remove the seat. NOTE: The rubber bushingsinside the seat may fall out during removal; Make sure they are in place upon reassembly.2. Remove both side covers.3. Remove the (5) five bolts in the rear fender (license plate panel, between saddlebags)with a 5mm Allen head socket. Remove the rear fender. NOTE: The fifth bolt is behindthe license plate.4. Remove the (3) three bolts in the passenger floorboard holder cover with a 5mm Allenhead socket. Remove the cover and repeat for other side.5. Remove the (2) bolts in the rear saddlebag guard with a 12mm socket. Remove thesaddlebag guard and repeat for other side 6. Remove the bolt in the muffler hanger using a 12mm socket. Repeat for other side.7. Loosen, but do not remove, the muffler clamps using a 6mm Allen head socket. Rotatethe mufflers down slightly to allow the hitch hoop to slide between the mufflers and the saddlebag

2005-2009 ROYAL STAR TOUR DELUXE & 1999-2010 VENTURE OVAL BAG SLASH SLIP-ON MUFFLER SET INSTALLATION MANUAL

0

Filed Under (Yamaha) by admin on 09-11-2010

download
1. Loosen the bolt on the front clamp securing the muffler to the headpipe. Important: Do not unbolt the OEM headpipes. 2. Loosen and remove the bolt from the muffler hanger located beneath the saddlebag. 3. Pull the muffler off the headpipe. It may be necessary to rotate the muffler and wiggle it a bit to free it. 4. Place a new exhaust clamp on the front of your new Oval Slash pipe. 5. Slide the new exhaust over the headpipe by rotating it and pushing it forward at the same time. 6. Align the hole in the mounting bracket and reinsert the OEM rear mounting bolt with the supplied nut and lock washer. Finger tighten only at this point of the installation. 7. After the brackets are in place, securely tighten all exhaust pipe clamps and brackets. 8. Reinstall the saddlebag. 9. Repeat Step #1 through Step #9 for the other side of the motorcycle. 10. For optimum performance we recommend the carburetors air/fuel mixtures be adjusted for the change in exhaust flow and back pressure. For best results, this procedure should be performed by a qualified Yamaha service technician. 11. Tighten all bolts/nuts after riding 100 miles, including baffle retaining screws

2005 Yamaha Royal Star Tour Deluxe speedo Healer Installation Manual

0

Filed Under (Yamaha) by admin on 09-11-2010

download
The speed sensor is on the left side (looking from the back towards the front of the motorcycle). Just FYI, here is the speed sensor coming off of the drive shaft behind the left saddlebag. The speed sensor connection for the Speedo Healer is behind this red cover. Take off the seat. There are two screws. One pointed out by the arrow and one on the opposite side. Also, remove the screw on the red cover. After removing the screw on the red cover, remove the cover by pulling it straight away from the bike. It is held on by 2 rubber grommets. The arrow points to the speed sensor coupler. Pull the connection apart. There is a little tab holding the connector together that will need to be depressed in order to get it apart.Hook the SH harness into the appropriate connectors. It only goes one way. The Yamaha plug and go kit works perfectly with no splicing required. Here is a close-up of the connection. Run the cable up under the bar towards the battery and hook the wires up to the Speedo Healer unit. The speedo healer fits nicely right behind the battery. You can barely see it next to the intercom. Note, none of the wires in this example have been secured yet. Put the red cover back on. Figure out the error that needs to be adjusted and make the adjustments to the Speed Healer per their instructions. Put the seat back on and you’re good to go. Be sure to verify that your adjustment was correct before believing your speedometer to be accurate. With the right adjustment, it will be, but don’t wait for a cop to tell you that you miscalculated! The electronic cruise control was not affected by the installation of this unit. I ended up setting mine to -7.5% after chasing my wife’s ’03 Vue for a couple of times. I ended up reading 59mph to her 60mph (previously it read 65mph to her 60mph) which is right where I wanted it since her speedometer reads a little fast, too. My back tire is about halfway worn. Your adjustment may vary

Yamaha Royalstar Royal Star Tour Deluxe Speedo Healer Installation

0

Filed Under (Yamaha) by admin on 07-01-2012

download
he speed sensor is on the left side (looking from the back towards the front of the motorcycle). Just FYI, here is the speed sensor coming off of the drive shaft behind the left saddlebag. – 7/2 -The speed sensor connection for the Speedo Healer is behind this red cover. Take off the seat. There are two screws. One pointed out by the arrow and one on the opposite side. Also, remove the screw on the red cover. After removing the screw on the red cover, remove the cover by pulling it straight away from the bike. It is held on by 2 rubber grommets. – 7/3 -The arrow points to the speed sensor coupler. Pull the connection apart. There is a little tab holding the connector together that will need to be depressed in order to get it apart. – 7/4 -Hook the SH harness into the appropriate connectors. It only goes one way. The Yamaha plug and go kit works perfectly with no splicing required. Here is a close-up of the connection. – 7/5 -Run the cable up under the bar towards the battery and hook the wires up to the Speedo Healer unit. – 76 -The speedo healer fits nicely right behind the battery. You can barely see it next to the intercom. Note, none of the wires in this example have been secured yet. Put the red cover back on. Figure out the error that needs to be adjusted and make the adjustments to the Speed Healer per their instructions. Put the seat back on and you’re good to go. Be sure to verify that your adjustment was correct before believing your speedometer to be accurate. With the right adjustment, it will be, but don’t wait for a cop to tell you that you miscalculated! The electronic cruise control was not affected by the installation of this unit. I ended up setting mine to -7.5% after chasing my wife’s ’03 Vue for a couple of times. I ended up reading 59mph to her 60mph (previously it read 65mph to her 60mph) which is right where I wanted it since her speedometer reads a little fast, too. My back tire is about halfway worn. Your adjustment may vary

Incoming search terms:

HONDA GL1500CD/ VALKYRIE Specifications

0

Filed Under (Honda) by admin on 29-01-2011

download
position when it comes to the environment. We continue to develop low-emission technologies for our current and future motorcycles, ATVs, scooters and personal watercraft. We already produce models that exceed the stringent 2008 CARB emissions requirements years ahead of schedule. And that’s the kind of performance everybody can appreciate. BE A RESPONSIBLE RIDER. Riding a motorcycle is an exercise in responsibility—to yourself, to others, to the environment and to the sport. So remember, wear a helmet, eye protection and protective clothing whenever you ride. Never ride under the influence of drugs or alcohol, and never use the street as a racetrack. Inspect your motorcycle before riding, read your owner’s manual, and see your local Honda Dealer concerning reimbursement through the Honda Rider’s Club of America™for Motorcycle Safety Foundation (MSF) rider training.* Always obey local laws, use common sense, and respect the rights of others when you ride. Make sure you have a proper license when riding on public roads, and never modify your motorcycle’s exhaust system. 03 SPECIFICATIONS ACCESSORIES VALKYRIE Log on to our website at honda.com for more information about Honda Genuine Accessories . On a bike like the Valkyrie, you can never have too much chrome. And that’s precisely why we offer our Chrome Sidecovers and Chrome Swingarm-Pivot cover to help really brighten up these areas. Here’s one of our most popular Valkyrie accessory options. These Leather Saddlebags look great, hold plenty, and match some of the other leather accessories we have available. Got a long trip planned, or is winter right around the corner? Then make sure you take a look at-or should we say take a look through-a Honda Genuine Accessories Windshield for your new Valkyrie. GL1500CD 1520cc liquid-cooled horizontally opposed six-cylinder with belt-driven overhead camshafts Six 28mm constant-velocity carburetors 71.0 x 64.0mm Solid-state digital Five-speed constant-mesh Shaft 150/80R-17 radial 180/70R-16 radial Dual-disc with twin-piston calipers 28.9 inches 66.5 inches 5.3 gallons, including 1.1 gallon reserve 681 pounds Black Windshield, leather saddlebags, chrome exhaust tips, chrome rear carrier, CB transceiver kit, passenger CB talk switch, studded backrest pad, studded main seat, studded rear seat, deluxe backrest pad

Incoming search terms: