bjaj scoter whireingin bike battery charger pucs download

You search Auto repair manual PDF bjaj scoter whireingin bike battery charger pucs download, if there are search results will appear below. If search results do not exist, please search by others keyword.



  bjaj scoter whireingin bike battery charger pucs download Direct Download speed 5282 Kb/s

  bjaj scoter whireingin bike battery charger pucs download Full Version speed 6162 Kb/s



HARLEY DAVIDSON CHROME BATTERY COVER TRIM REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 21-03-2011

download
REMOVAL 1. See Figure 3. Remove button-head screw (A) that attaches battery cover (B) to battery tray (C). 2. See Figure 1. Remove battery cover by lifting it over the two tabs on the battery tray. NOTE The original equipment battery cover trim has four pinch tabs on the reverse side that attach it to the battery cover. 3. See Figure 2. Remove original equipment battery cover trim from battery cover by pushing the four pinch tabs out of the battery cover using a pliers or suitable tool. INSTALLATION 1. Place battery cover over the two tabs on battery tray (C) and attach it to battery tray with button-head screw (A). Tighten screw to 20-40 in-lbs (2.3-4.6 Nm). 2. Obtain chrome battery cover trim (1) from kit. 3. Using a 50/50 isopropyl alcohol/water solution, thoroughly clean the surface where the chrome trim will be installed. Let it dry completely. NOTE Test the trim mount fit prior to removing the adhesive backing from the chrome battery cover trim. 4. Remove adhesive liner from the chrome battery cover trim. NOTE The ideal temperature should be at least 60° F (16° C) for proper adhesion of the chrome trim on the battery cover. 5. Center and install chrome trim onto the battery cover. Apply firm pressure for one minute using a cloth to prevent scratching the battery cover and battery trim. 6. Let the adhesive cure for 24 hours at no less than 60° F (16° C)

Incoming search terms:

HARLEY-DAVIDSON 12 VOLT BATTERIES CARE AND MAINTENANCE

0

Filed Under (Harley Davidson) by admin on 30-01-2011

download
CARE AND MAINTENANCE Voltmeter Test See Table 2. The voltmeter test provides a general indicator of battery condition. Check the voltage of the battery to verify that it is in a 100% fully-charged condition. If the open circuit (disconnected) voltage reading is below 12.7 V, charge the battery and then check the voltage again after the battery has set for one to two hours. If the voltage reading is 12.7 V or above, perform a load test. Table 2. Voltmeter Test For Battery Charge Conditions STATE OF CHARGE VOLTAGE (OCV) 100% 12.7 V 75% 12.6 V 50% 12.3 V 25% 12.0 V 0% 11.8 V Disconnection and Removal Refer to a service manual for specific disconnection and removal steps. Pay attention to all warnings and cautions within the manual and remove battery from battery box/tray. Battery Charging Batteries contain sulfuric acid, which could cause severe burns to eyes and skin. Wear a protective face shield, rubberized gloves and protective clothing when working with batteries. KEEP BATTERIES AWAY FROM CHILDREN. (00063a) 1. Never charge a battery without first reviewing the instructions for the charger being used. 2. Perform a voltmeter test to determine the state of charge. See BATTERY TESTING, VOLTMETER TEST. If battery needs to be charged, proceed to Step 3. Remove battery from motorcycle before charging. Electrolyte leakage will damage motorcycle parts. (00213a) Explosive hydrogen gas, which escapes during charging, could cause death or serious injury. Charge battery in a well-ventilated area. Keep open flames, electrical sparks and smoking materials away from battery at all times. KEEP BATTERIES AWAY FROM CHILDREN. (00065a) 3. See applicable service manual and remove the battery from the motorcycle. Place the battery on a level surface. 4. Inspect battery for damage. Replace battery if visibly damaged or frozen. 5. Inspect battery charger, verify that the charger leads are not damaged, frayed or loose

Incoming search terms:

620A-230, 2620A-230-B 20 AMP ON BOARD BATTERY CHARGER Two Output OWNER'S MANUAL

0

Filed Under (Tips and Review) by admin on 28-11-2010

download
INSTALLING THE CHARGER Choosing Charging Location The charger should have at least eight inches of unobstructed area on all sides of the unit for effective cooling. The case of this charger will become warm during operation. Do not install the charger on carpeted, upholstered, or varnished surfaces. Mounting the Charger 1. Use corrosion resistant ¼” dia. bolts, backed by a flat washer, and secured to the mounting surface with a split-ring lock washer. 2. Hold the charger to the mounting surface and mark the holes. 3. Remove the charger and drill the mounting holes. 4. Align the charger and assemble the mounting hardware. Secure. Making DC and AC Connections Check polarity of the battery posts. The POSITIVE (POS., P, +) battery post usually has a larger diameter than the NEGATIVE (NEG., N, -) post. Refer to the pictures shown above for different configurations. After securing the battery connections, plug the AC line cord into an available AC outlet that is protected by a Ground Fault Circuit Interrupter (GFCI) breaker

Triumph Bonneville America And Speedmaster The Freak Installation Instructions and Parts List

0

Filed Under (Triumph) by admin on 29-10-2010

download
INSTALLATION In order to install The Freak, the factory air-box must be removed. Because of it’s design, the factory air-box is not an item that is easily removed. There are several parts that must be removed in order to get the air-box out of the bike in one piece. We recommend using the following method to remove your air box without having to cut it into smaller pieces in order to get it out of the frame. 1. PARTS REMOVAL In order to gain access to the air-box, it is necessary to remove certain parts of the motorcycle to gain access to the air-box area of the frame. Removing the following parts should be the first steps you take. A. Seats – Remove both seats starting with the passenger pillion, if applicable. B. Side cover and grommets – Remove the plastic side cover on the right side (throttle side) of your motorcycle. This is the faux oil-tank cover that has the name of your bike on it. Underneath the side cover there are three rubber grommets (1 on the frame tab, and two on the air-box) that support the side cover. Remove the two that are on the air-box and leave the one on the frame. You will attach the two that you removed to the right side bracket in Section 4C . C. Faux air filter covers – On the right side of the bike, remove the chrome faux air filter covers, by removing the one allen head screw that holds it onto the air-box. On the left hand side (clutch side) remove the faux air filter cover in the same manner, you removed the one on the right. D. Plastic shrouds – on the left side, remove the black plastic air-box shroud, by removing the two allen head screws holding it in place. Then remove the plastic shroud covering your fuse box (this is the piece that surrounds your ignition terminal next to the battery). E. Battery – Remove the battery by unscrewing the torx-head bolt that holds the chrome bracket in place. Remove the chrome bracket and the black plastic cap. Tilt the battery out of the box with the top towards you. Disconnect both battery terminal connectors, negative (-) terminal first. Remove the battery. F. Battery box – Remove the two bolts that hold the battery box to the frame. Pull the battery box out as far as you can, then remove the the ignition terminal from the battery box, by removing the two allen screws that hold it in place from the back. Next, remove the fuse box from the battery box, by pushing it out from the back. It is not necessary to disconnect any of the wiring going to the fuse box, or the ignition terminal. G. Rear fender – Remove the rear fender, by first disconnecting the taillight wires. Follow the wires from the tail light assembly on the inside of the rear fender (left side) towards the front of the bike until you come to the box connector. Disconnect the tail light wires at this connector, being careful not to break it. Once the wiring is disconnected, remove the 6 bolts that hold it to the struts. Have someone hold the fender for you while you are removing all of the bolts so that it does not drop once the bolts are removed. Slide the fender out the rear of the bike. 2. PREPARE THE MOTORCYCLE FOR AIR-BOX REMOVAL To remove the factory air-box without damaging it, it is necessary to lift the bike. We recommend the use of a multi-position ATV/motorcycle jack with a minimum lift height of 10″. A. Setting up the lift – Place the lift under your bike and secure your bike to the lift according to the lift manufacturer’s instructions. B. Raise slightly – Lift the motorcycle to the point where the rear springs are without tension, but NOT to where the rear tire is off the ground. C. Remove the rear springs – Take off each of the rear springs by removing the the two bolts on each spring. Once all the bolts are removed gently pull the springs out off of the studs. If they do not pull off easily, you can raise or lower the bike slightly with the lift to ease tension on the spring. Remember, you should not have the rear tire off the ground at this point. The bike should only be raised enough to relax the tension in the springs. D. Remove the mufflers – Remove the mufflers by loosening the clamp at the exhaust header, and by removing the rear foot peg hangers. If the mufflers are not removed, they can become damaged by the axles in Section 2H . E. Disconnect the carburetors – With a small flathead screwdriver, pull the retainer springs out of the channel of the carburetor intake tubes (the two large black tubes coming from the air box into the back of each carburetor), and simply push them towards the air box off of the carbs

Incoming search terms:

HARLEY DAVIDSON BATTERY CHARGING HARNESS (THREE-PIN) INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 11-02-2011

download
1. Follow the instructions in your Owner’s Manual to remove the seat and any other components (side covers, etc.) necessary to provide access to the battery. 2. Refer to the applicable view in Figure 1 for your model. Break the battery negative (-) connection by removing the hardware assembly from the negative battery terminal. 3. Break the positive (+) battery connection by removing the hardware assembly from the positive battery terminal. 4. Clean the battery terminals and cable connectors using a wire brush or sandpaper to remove any oxidation. 5. Apply a light coating of Harley-Davidson electrical contact lubricant (Part Number 99861-02) to the battery terminals, cable connectors, battery charging harness ring terminals and connector located under the weather- shield cap. Connect positive (+) battery cable first. If positive (+) cable should contact ground with negative (-) cable connected, the resulting sparks can cause a battery explosion, which could result in death or serious injury. (00068a) 6. Refer to the view in Figure 1 used for disassembly. Install the positive (RED) lead of the harness to the positive (+) battery post following the sequence shown. • On 1999 and earlier models (with original equipment), torque the positive (+) terminal post bolt to 40 in-lbs (4.5 Nm). • On 2000 and later models (with original equipment), torque the positive (+) terminal post bolt to 60-96 in-lbs (6.8-10.9 Nm). 7. Attach the negative (BLACK) lead of the harness to the negative (-) battery post following the sequence shown. • On 1999 and earlier models (with original equipment), torque the negative (-) terminal post bolt to 40 in-lbs (4.5 Nm). • On 2000 and later models (with original equipment), torque the negative (-) terminal post bolt to 60-96 in-lbs (6.8-10.9 Nm). Harness Routing Do not route the harness near any moving parts. Contact with moving parts may result in damage to harness. Refer to the following sections to determine the correct harness routing for your model. Be sure to avoid any components that may pinch or cut the harness, and avoid components that radiate heat. Take up any slack in the cable and store out of sight. Secure the harness with cable straps (H-D Part Number 10006), which can be purchased separately from any Harley Davidson Dealer. VRSC Model Harness Routing 1. See Figure 2. Route the battery harness/ connector (3) toward the front of the bike following the upper left frame tube. Cleanly tuck the in-line fuse (2) into the space in front of the battery. 2. Continue to route the harness/ gray connector to the front of the bike and behind the vent cover. Secure the harness with a cable strap and let the connector protrude past the cover for easy access. Trim any excess from the cable strap

Incoming search terms:

HARLEY DAVIDSON DYNA BATTERY COVER INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 18-03-2011

download
INSTALLATION 1. Remove seat. To prevent accidental vehicle start-up, which could cause death or serious injury, disconnect negative (-) battery cable before proceeding. (00048a) Disconnect negative (-) battery cable first. If positive (+) cable should contact ground with negative (-) cable connected, the resulting sparks can cause a battery explosion, which could result in death or serious injury. (00049a) 2. Disconnect battery cables, negative cable first. 3. Follow instructions in applicable Service Manual to loosen and lower battery tray. 4. Remove top and side covers and discard. 5. See Figure 1. Install cover from kit as follows: a. Align bottom of cover with tray (2) making sure that three clips on bottom properly seat (center) on both sides of retaining lip (6) at the base of the battery tray. b. Position top of cover (5) under the frame tube. 6. Raise tray and cover following instructions in Service Manual and tighten bolts (3,4) securely. 5 3 2 1 4 6 is 01648 1. Battery 2. Battery tray 3. Upper mounting bolt 4. Lower mounting bolt 5. Battery cover 6. Retaining lip Figure 1. Battery Cover and Mounting Hardware Connect positive (+) battery cable first. If positive (+) cable should contact ground with negative (-) cable connected, the resulting sparks can cause a battery explosion, which could result in death or serious injury. (00068a) 7. Connect battery cables, positive cable first. 8. Install seat

SUZUKI SV650 ELECTRICAL SYSTEM REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Suzuki) by admin on 26-02-2011

download
CAUTIONS IN SERVICING CONNECTOR • * When connecting a connector, be sure to push it in until a click is felt. • * Inspect the connector for corrosion, contamination and breakage in its cover . COUPLER • With a lock type coupler, be sure to release the lock before disconnecting it and push it in fully till the lock works when connecting it . • * When disconnecting the coupler, be sure to hold the coupler itself and do not pull the lead wires . • * Inspect each terminal on the coupler for being loose or bent . • * Inspect each terminal for corrosion and contamination. CLAMP • * Clamp the wire harness at such positions as indicated in “WIRE HARNESS ROUTING”. ( r- 79-14 to 9-16) • * Bend the clamp properly so that the wire harness is clamped securely. • * In clamping the wire harness, use care not to allow it to hang down. • * Do not use wire or any other substitute for the band type clamp. FUSE • * When a fuse blows, always investigate the cause, correct it and then replace the fuse . • * Do not use a fuse of a different capacity . • * Do not use wire or any other substitute for the fuse . i SEMI-CONDUCTOR EQUIPPED PART • * Be careful not to drop the part with a semi-conductor built in such as a ECM. • * When inspecting this part, follow inspection instruction strictly . Neglecting proper procedure may cause damage to this part . BATTERY • The MF battery used in this motorcycle does not require maintenance (e.g., electrolyte level inspection, distilled water replenishment) . • * During normal charging, no hydrogen gas is produced. However, if the battery is overcharged, hydrogen gas may be produced. Therefore, be sure there are no fire or spark sources (e.g., short circuit) nearby when charging the battery . • * Be sure to recharge the battery in a well-ventilated and open area. •Note that the charging system for the MF battery is different from that of a conventional battery. Do not replace the MF battery with a conventional battery . CONNECTING THE BATTERY •When disconnecting terminals from the battery for disassembly or servicing, be sure to disconnect the O battery lead wire, first. • * When connecting the battery lead wires, be sure to connect the OO battery lead wire, first . • * If the terminal is corroded, remove the battery, pour warm water over it and clean it with a wire brush . • * After connecting the battery, apply a light coat of grease to the battery terminals. • * Install the cover over the O battery terminal. WIRING PROCEDURE • * Properly route the wire harness according to the “WIRE ROUTING” section. (C’9-14 to 9-16) ELECTRICAL SYSTEM 8- 3
8-4 ELECTRICAL SYSTEM USING THE MULTI CIRCUIT TESTER •Properly use the multi circuit tester Oand Oprobes. Improper use can cause damage to the motorcycle and tester. • * If the voltage and current values are not known, begin measuring in the highest range . • * When measuring the resistance, make sure that no voltage is applied. If voltage is applied, the tester will be damaged . • * After using the tester, be sure to turn the switch to the OFF position. CAUTION Before using the multi circuit tester, read its instruction manual.

SUZUKI SV1000 ELECTRICAL SYSTEM SERVICE MANUAL

0

Filed Under (Suzuki) by admin on 26-02-2011

download
COUPLER •With a lock type coupler, be sure to release the lock before disconnecting it and push it in fully till the lock works when connecting it . • * When disconnecting the coupler, be sure to hold the coupler itself and do not pull the lead wires . • * Inspect each terminal on the coupler for being loose or bent . • * Inspect each terminal for corrosion and contamination. CLAMP • * Clamp the wire harness at such positions as indicated in “WIRE HARNESS ROUTING”. (C” -78-14) • * Bend the clamp properly so that the wire harness is clamped securely . • * In clamping the wire harness, use care not to allow it to hang down. • * Do not use wire or any other substitute for the band type clamp. FUSE • * When a fuse blows, always investigate the cause, correct it and then replace the fuse . • * Do not use a fuse of a different capacity . • * Do not use wire or any other substitute for the fuse . SEMI-CONDUCTOR EQUIPPED PART • * Be careful not to drop the part with a semi-conductor built in such as a ECM. • * When inspecting this part, follow inspection instruction strictly . Neglecting proper procedure may cause damage to this part . ELECTRICAL SYSTEM 7- 3 7-4 ELECTRICAL SYSTEM BATTERY •The MF battery used in this motorcycle does not require maintenance (e.g., electrolyte level inspection, distilled water replenishment) . • * During normal charging, no hydrogen gas is produced. However, if the battery is overcharged, hydrogen gas may be produced. Therefore, be sure there are no fire or spark sources (e.g., short circuit) nearby when charging the battery . • * Be sure to recharge the battery in a well-ventilated and open area. • Note that the charging system for the MF battery is different from that of a conventional battery. Do not replace the MF battery with a conventional battery . CONNECTING THE BATTERY •When disconnecting terminals from the battery for disassembly or servicing, be sure to disconnect the O battery lead wire, first. • * When connecting the battery lead wires, be sure to connect the OO battery lead wire first . • * If the terminal is corroded, remove the battery, pour warm water over it and clean it with a wire brush . • * After connecting the battery, apply a light coat of grease to the battery terminals. • * Install the cover over the O battery terminal. WIRING PROCEDURE • * Properly route the wire harness according to the “WIRE HARNESS ROUTING” section. (CJ8-14)

Incoming search terms:

Honda CR 125/ 250R The MSD Enhancer Ignition INSTALLATION

0

Filed Under (Honda) by admin on 27-11-2011

download
The following explains some technical aspects of the Enhancer Ignition. Battery: The battery is necessary to the operation of the Enhancer in two regards. • The battery supplies voltage to the complex timing feature of the Enhancer.
• The Enhancer has a built in boost circuit that amplifies the spark energy at low rpm where the stock magneto is insufficient. The MSD NiCad Battery pack, PN 4381, must be charged with the recommended battery charger or an MSD Fast Charger, PN 4385. The battery should be completely discharged before recharging. If a 7.2 Battery Charger is used, the recommended time for charging is seven hours. With the MSD Fast Charger the battery only needs to charge for one hour. Note: No fast charger besides the MSD Fast Charger may be used to charge the MSD NiCad Battery. Damage to the battery will occur. Timing: The Enhancer Ignition allows the user to adjust the ignition timing curve to optimize engine
power output. This is done by rotating the potentiometer shaft located on the back of the ignition. Clockwise rotation retards the timing while counterclockwise advances the timing (Figure 1). Coil: The MSD Enhancer Ignition System includes a special Pro CD Coil. This coil has an extremely low primary resistance and a high turns ratio to produce maximum spark energy. The Pro CD Coil is encapsulated in a Rynite compound that is impervious to contaminates and vibration. Note: Do not use the stock coil with the Enhancer Ignition

Harley-Davidson touring bikes WHEELDOCK EZ-UP Center Stand Installation Instructions

0

Filed Under (Harley Davidson) by admin on 18-04-2012

download
Unlike other center stands, the WHEELDOCK EZ UP stand requires very little effort to operate and can usually be done while still on the bike by simply pushing down on the foot lever with your left foot. Once you feel both feet of the center stand in contact with the ground, transfer your weight up off of the seat and onto the foot lever of the center stand. The stand should rotate under the bike and a bit forward lifting the bike quite easily. CAUTION: Never attempt to raise the bike with a passenger on board, as you will damage the foot lever. You can also raise the bike on the center stand by using the following traditional method: Place the bike on the side stand and step off to the side. From the left side of the bike, push the bike up to the vertical position and press down on the foot lever until both feet of the stand are in contact with the ground. Now apply weight to the foot lever while lifting up on the bike. For cleaning the rear wheel: first place a ½-inch piece of plywood under the stand and use this (beside the bike) method for placing the bike up on the plywood spacer; this will allow the wheel to rotate freely for cleaning. Do not try this while on the bike, as it will require too much foot pressure on the lever. You now have two options to get the bike off of the stand: You can simply rock the bike forward, or put the bike in gear and drive off in most cases as long as you are parked on a flat, level surface. Tips for solving common problems: If you have the correct height stand and you still have difficulty getting the bike up on the stand check the following: the bike must be in neutral, the wheel should be straight forward and not cocked, do not hold the front brake lever and make sure you have 15 lb or more air pressure in the rear suspension. These are the most common problems we encounter.

Incoming search terms:

Incoming search terms: